[v3,08/10] phy: cadence: Add driver for HDP-TX DisplyPort PHY

Message ID e2706bb8937a10ad7edf253fe8c928f6b22e25f1.1667911321.git.Sandor.yu@nxp.com
State New
Headers
Series Initial support for Cadence MHDP(HDMI/DP) for i.MX8MQ |

Commit Message

Sandor Yu Nov. 8, 2022, 1 p.m. UTC
  Add Cadence HDP-TX DisplayPort PHY driver.

Cadence HDP-TX PHY could be put in either DP mode or
HDMI mode base on the configuration chosen.
DisplayPort PHY mode is configurated in the driver.

Signed-off-by: Sandor Yu <Sandor.yu@nxp.com>
---
 drivers/phy/cadence/Kconfig                |   8 +
 drivers/phy/cadence/Makefile               |   1 +
 drivers/phy/cadence/phy-cadence-hdptx-dp.c | 774 +++++++++++++++++++++
 3 files changed, 783 insertions(+)
 create mode 100644 drivers/phy/cadence/phy-cadence-hdptx-dp.c
  

Comments

Vinod Koul Nov. 10, 2022, 7:40 a.m. UTC | #1
On 08-11-22, 21:00, Sandor Yu wrote:
> Add Cadence HDP-TX DisplayPort PHY driver.
> 
> Cadence HDP-TX PHY could be put in either DP mode or
> HDMI mode base on the configuration chosen.
> DisplayPort PHY mode is configurated in the driver.
> 
> Signed-off-by: Sandor Yu <Sandor.yu@nxp.com>
> ---
>  drivers/phy/cadence/Kconfig                |   8 +
>  drivers/phy/cadence/Makefile               |   1 +
>  drivers/phy/cadence/phy-cadence-hdptx-dp.c | 774 +++++++++++++++++++++
>  3 files changed, 783 insertions(+)
>  create mode 100644 drivers/phy/cadence/phy-cadence-hdptx-dp.c
> 
> diff --git a/drivers/phy/cadence/Kconfig b/drivers/phy/cadence/Kconfig
> index 1adde2d99ae7..1e1914d3afdc 100644
> --- a/drivers/phy/cadence/Kconfig
> +++ b/drivers/phy/cadence/Kconfig
> @@ -46,3 +46,11 @@ config PHY_CADENCE_SALVO
>  	  Enable this to support the Cadence SALVO PHY driver,
>  	  this PHY is a legacy PHY, and only are used for USB3
>  	  and USB2.
> +
> +config PHY_CADENCE_HDPTX_DP

alphabetically sorted please

> +	tristate "Cadence HDPTX DP PHY Driver"
> +	depends on OF && HAS_IOMEM
> +	depends on COMMON_CLK
> +	select GENERIC_PHY
> +	help
> +	  Enable this to support the Cadence HDPTX DP PHY driver
> diff --git a/drivers/phy/cadence/Makefile b/drivers/phy/cadence/Makefile
> index e17f035ddece..fbdb0bc5ff11 100644
> --- a/drivers/phy/cadence/Makefile
> +++ b/drivers/phy/cadence/Makefile
> @@ -4,3 +4,4 @@ obj-$(CONFIG_PHY_CADENCE_DPHY)	+= cdns-dphy.o
>  obj-$(CONFIG_PHY_CADENCE_DPHY_RX)	+= cdns-dphy-rx.o
>  obj-$(CONFIG_PHY_CADENCE_SIERRA)	+= phy-cadence-sierra.o
>  obj-$(CONFIG_PHY_CADENCE_SALVO)	+= phy-cadence-salvo.o
> +obj-$(CONFIG_PHY_CADENCE_HDPTX_DP)	+= phy-cadence-hdptx-dp.o

here too

> diff --git a/drivers/phy/cadence/phy-cadence-hdptx-dp.c b/drivers/phy/cadence/phy-cadence-hdptx-dp.c
> new file mode 100644
> index 000000000000..079d43772d1d
> --- /dev/null
> +++ b/drivers/phy/cadence/phy-cadence-hdptx-dp.c
> @@ -0,0 +1,774 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Cadence HDP-TX Display Port Interface (DP) PHY driver
> + *
> + * Copyright (C) 2022 NXP Semiconductor, Inc.
> + */
> +#include <asm/unaligned.h>
> +#include <linux/clk.h>
> +#include <linux/kernel.h>
> +#include <linux/phy/phy.h>
> +#include <linux/platform_device.h>
> +#include <linux/io.h>
> +#include <linux/iopoll.h>
> +
> +#include <drm/bridge/cdns-mhdp-mailbox.h>
> +
> +#define ADDR_PHY_AFE	0x80000
> +
> +/* PHY registers */
> +#define CMN_SSM_BIAS_TMR                0x0022
> +#define CMN_PLLSM0_PLLEN_TMR            0x0029
> +#define CMN_PLLSM0_PLLPRE_TMR           0x002A
> +#define CMN_PLLSM0_PLLVREF_TMR          0x002B
> +#define CMN_PLLSM0_PLLLOCK_TMR          0x002C
> +#define CMN_PLLSM0_USER_DEF_CTRL        0x002F
> +#define CMN_PSM_CLK_CTRL                0x0061
> +#define CMN_CDIAG_REFCLK_CTRL           0x0062
> +#define CMN_PLL0_VCOCAL_START           0x0081
> +#define CMN_PLL0_VCOCAL_INIT_TMR        0x0084
> +#define CMN_PLL0_VCOCAL_ITER_TMR        0x0085
> +#define CMN_PLL0_INTDIV                 0x0094
> +#define CMN_PLL0_FRACDIV                0x0095
> +#define CMN_PLL0_HIGH_THR               0x0096
> +#define CMN_PLL0_DSM_DIAG               0x0097
> +#define CMN_PLL0_SS_CTRL1               0x0098
> +#define CMN_PLL0_SS_CTRL2               0x0099
> +#define CMN_ICAL_INIT_TMR               0x00C4
> +#define CMN_ICAL_ITER_TMR               0x00C5
> +#define CMN_RXCAL_INIT_TMR              0x00D4
> +#define CMN_RXCAL_ITER_TMR              0x00D5
> +#define CMN_TXPUCAL_CTRL                0x00E0
> +#define CMN_TXPUCAL_INIT_TMR            0x00E4
> +#define CMN_TXPUCAL_ITER_TMR            0x00E5
> +#define CMN_TXPDCAL_CTRL                0x00F0
> +#define CMN_TXPDCAL_INIT_TMR            0x00F4
> +#define CMN_TXPDCAL_ITER_TMR            0x00F5
> +#define CMN_ICAL_ADJ_INIT_TMR           0x0102
> +#define CMN_ICAL_ADJ_ITER_TMR           0x0103
> +#define CMN_RX_ADJ_INIT_TMR             0x0106
> +#define CMN_RX_ADJ_ITER_TMR             0x0107
> +#define CMN_TXPU_ADJ_CTRL               0x0108
> +#define CMN_TXPU_ADJ_INIT_TMR           0x010A
> +#define CMN_TXPU_ADJ_ITER_TMR           0x010B
> +#define CMN_TXPD_ADJ_CTRL               0x010c
> +#define CMN_TXPD_ADJ_INIT_TMR           0x010E
> +#define CMN_TXPD_ADJ_ITER_TMR           0x010F
> +#define CMN_DIAG_PLL0_FBH_OVRD          0x01C0
> +#define CMN_DIAG_PLL0_FBL_OVRD          0x01C1
> +#define CMN_DIAG_PLL0_OVRD              0x01C2
> +#define CMN_DIAG_PLL0_TEST_MODE         0x01C4
> +#define CMN_DIAG_PLL0_V2I_TUNE          0x01C5
> +#define CMN_DIAG_PLL0_CP_TUNE           0x01C6
> +#define CMN_DIAG_PLL0_LF_PROG           0x01C7
> +#define CMN_DIAG_PLL0_PTATIS_TUNE1      0x01C8
> +#define CMN_DIAG_PLL0_PTATIS_TUNE2      0x01C9
> +#define CMN_DIAG_PLL0_INCLK_CTRL        0x01CA
> +#define CMN_DIAG_PLL0_PXL_DIVH          0x01CB
> +#define CMN_DIAG_PLL0_PXL_DIVL          0x01CC
> +#define CMN_DIAG_HSCLK_SEL              0x01E0
> +#define CMN_DIAG_PER_CAL_ADJ            0x01EC
> +#define CMN_DIAG_CAL_CTRL               0x01ED
> +#define CMN_DIAG_ACYA                   0x01FF
> +#define XCVR_PSM_RCTRL                  0x4001
> +#define XCVR_PSM_CAL_TMR                0x4002
> +#define XCVR_PSM_A0IN_TMR               0x4003
> +#define TX_TXCC_CAL_SCLR_MULT_0         0x4047
> +#define TX_TXCC_CPOST_MULT_00_0         0x404C
> +#define TX_TXCC_MGNFS_MULT_000_0        0x4050
> +#define XCVR_DIAG_PLLDRC_CTRL           0x40E0
> +#define XCVR_DIAG_PLLDRC_CTRL           0x40E0
> +#define XCVR_DIAG_HSCLK_SEL             0x40E1
> +#define XCVR_DIAG_BIDI_CTRL             0x40E8
> +#define XCVR_DIAG_LANE_FCM_EN_MGN_TMR   0x40F2
> +#define XCVR_DIAG_LANE_FCM_EN_MGN       0x40F2
> +#define TX_PSC_A0                       0x4100
> +#define TX_PSC_A1                       0x4101
> +#define TX_PSC_A2                       0x4102
> +#define TX_PSC_A3                       0x4103
> +#define TX_RCVDET_CTRL                  0x4120
> +#define TX_RCVDET_EN_TMR                0x4122
> +#define TX_RCVDET_EN_TMR                0x4122
> +#define TX_RCVDET_ST_TMR                0x4123
> +#define TX_RCVDET_ST_TMR                0x4123
> +#define TX_BIST_CTRL                    0x4140
> +#define TX_BIST_UDDWR                   0x4141
> +#define TX_DIAG_TX_CTRL                 0x41E0
> +#define TX_DIAG_TX_DRV                  0x41E1
> +#define TX_DIAG_BGREF_PREDRV_DELAY      0x41E7
> +#define TX_DIAG_BGREF_PREDRV_DELAY      0x41E7
> +#define XCVR_PSM_RCTRL_1                0x4201
> +#define TX_TXCC_CAL_SCLR_MULT_1         0x4247
> +#define TX_TXCC_CPOST_MULT_00_1         0x424C
> +#define TX_TXCC_MGNFS_MULT_000_1        0x4250
> +#define XCVR_DIAG_PLLDRC_CTRL_1         0x42E0
> +#define XCVR_DIAG_HSCLK_SEL_1           0x42E1
> +#define XCVR_DIAG_LANE_FCM_EN_MGN_TMR_1 0x42F2
> +#define TX_RCVDET_EN_TMR_1              0x4322
> +#define TX_RCVDET_ST_TMR_1              0x4323
> +#define TX_DIAG_ACYA_0                  0x41FF
> +#define TX_DIAG_ACYA_1                  0x43FF
> +#define TX_DIAG_ACYA_2                  0x45FF
> +#define TX_DIAG_ACYA_3                  0x47FF
> +#define TX_ANA_CTRL_REG_1               0x5020
> +#define TX_ANA_CTRL_REG_2               0x5021
> +#define TXDA_COEFF_CALC                 0x5022
> +#define TX_DIG_CTRL_REG_1               0x5023
> +#define TX_DIG_CTRL_REG_2               0x5024
> +#define TXDA_CYA_AUXDA_CYA              0x5025
> +#define TX_ANA_CTRL_REG_3               0x5026
> +#define TX_ANA_CTRL_REG_4               0x5027
> +#define TX_ANA_CTRL_REG_5               0x5029
> +#define RX_PSC_A0                       0x8000
> +#define RX_PSC_CAL                      0x8006
> +#define PMA_LANE_CFG                    0xC000
> +#define PIPE_CMN_CTRL1                  0xC001
> +#define PIPE_CMN_CTRL2                  0xC002
> +#define PIPE_COM_LOCK_CFG1              0xC003
> +#define PIPE_COM_LOCK_CFG2              0xC004
> +#define PIPE_RCV_DET_INH                0xC005
> +#define PHY_HDP_MODE_CTRL               0xC008
> +#define PHY_HDP_CLK_CTL                 0xC009
> +#define STS                             0xC00F
> +#define PHY_ISO_CMN_CTRL                0xC010
> +#define PHY_ISO_CMN_CTRL                0xC010
> +#define PHY_HDP_TX_CTL_L0               0xC408
> +#define PHY_DP_TX_CTL                   0xC408
> +#define PHY_HDP_TX_CTL_L1               0xC448
> +#define PHY_HDP_TX_CTL_L2               0xC488
> +#define PHY_HDP_TX_CTL_L3               0xC4C8
> +#define PHY_PMA_CMN_CTRL1               0xC800
> +#define PMA_CMN_CTRL1                   0xC800
> +#define PHY_PMA_ISO_CMN_CTRL            0xC810
> +#define PHY_PMA_ISO_PLL_CTRL1           0xC812
> +#define PHY_PMA_ISOLATION_CTRL          0xC81F
> +#define PHY_ISOLATION_CTRL              0xC81F
> +#define PHY_PMA_ISO_XCVR_CTRL           0xCC11
> +#define PHY_PMA_ISO_LINK_MODE           0xCC12
> +#define PHY_PMA_ISO_PWRST_CTRL          0xCC13
> +#define PHY_PMA_ISO_TX_DATA_LO          0xCC14
> +#define PHY_PMA_ISO_TX_DATA_HI          0xCC15
> +#define PHY_PMA_ISO_RX_DATA_LO          0xCC16
> +#define PHY_PMA_ISO_RX_DATA_HI          0xCC17

do you use all these?

> +
> +#define MAX_NUM_LANES		4
> +#define DEFAULT_MAX_BIT_RATE	5400 /* in Mbps */
> +
> +#define REF_CLK_27MHZ		27000000
> +
> +enum dp_link_rate {
> +	RATE_1_6 = 162000,
> +	RATE_2_1 = 216000,
> +	RATE_2_4 = 243000,
> +	RATE_2_7 = 270000,
> +	RATE_3_2 = 324000,
> +	RATE_4_3 = 432000,
> +	RATE_5_4 = 540000,
> +	RATE_8_1 = 810000,
> +};
> +
> +struct phy_pll_reg {
> +	u16 val[7];
> +	u32 addr;
> +};
> +
> +static const struct phy_pll_reg phy_pll_27m_cfg[] = {
> +	/*  1.62    2.16    2.43    2.7     3.24    4.32    5.4      register address */
> +	{{ 0x010E, 0x010E, 0x010E, 0x010E, 0x010E, 0x010E, 0x010E }, CMN_PLL0_VCOCAL_INIT_TMR },
> +	{{ 0x001B, 0x001B, 0x001B, 0x001B, 0x001B, 0x001B, 0x001B }, CMN_PLL0_VCOCAL_ITER_TMR },
> +	{{ 0x30B9, 0x3087, 0x3096, 0x30B4, 0x30B9, 0x3087, 0x30B4 }, CMN_PLL0_VCOCAL_START },
> +	{{ 0x0077, 0x009F, 0x00B3, 0x00C7, 0x0077, 0x009F, 0x00C7 }, CMN_PLL0_INTDIV },
> +	{{ 0xF9DA, 0xF7CD, 0xF6C7, 0xF5C1, 0xF9DA, 0xF7CD, 0xF5C1 }, CMN_PLL0_FRACDIV },
> +	{{ 0x001E, 0x0028, 0x002D, 0x0032, 0x001E, 0x0028, 0x0032 }, CMN_PLL0_HIGH_THR },
> +	{{ 0x0020, 0x0020, 0x0020, 0x0020, 0x0020, 0x0020, 0x0020 }, CMN_PLL0_DSM_DIAG },
> +	{{ 0x0000, 0x1000, 0x1000, 0x1000, 0x0000, 0x1000, 0x1000 }, CMN_PLLSM0_USER_DEF_CTRL },
> +	{{ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000 }, CMN_DIAG_PLL0_OVRD },
> +	{{ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000 }, CMN_DIAG_PLL0_FBH_OVRD },
> +	{{ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000 }, CMN_DIAG_PLL0_FBL_OVRD },
> +	{{ 0x0006, 0x0007, 0x0007, 0x0007, 0x0006, 0x0007, 0x0007 }, CMN_DIAG_PLL0_V2I_TUNE },
> +	{{ 0x0043, 0x0043, 0x0043, 0x0042, 0x0043, 0x0043, 0x0042 }, CMN_DIAG_PLL0_CP_TUNE },
> +	{{ 0x0008, 0x0008, 0x0008, 0x0008, 0x0008, 0x0008, 0x0008 }, CMN_DIAG_PLL0_LF_PROG },
> +	{{ 0x0100, 0x0001, 0x0001, 0x0001, 0x0100, 0x0001, 0x0001 }, CMN_DIAG_PLL0_PTATIS_TUNE1 },
> +	{{ 0x0007, 0x0001, 0x0001, 0x0001, 0x0007, 0x0001, 0x0001 }, CMN_DIAG_PLL0_PTATIS_TUNE2 },
> +	{{ 0x0020, 0x0020, 0x0020, 0x0020, 0x0020, 0x0020, 0x0020 }, CMN_DIAG_PLL0_TEST_MODE},
> +	{{ 0x0016, 0x0016, 0x0016, 0x0016, 0x0016, 0x0016, 0x0016 }, CMN_PSM_CLK_CTRL }
> +};
> +
> +struct cdns_hdptx_dp_phy {
> +	void __iomem *regs;	/* DPTX registers base */
> +	struct device *dev;
> +	struct phy *phy;
> +	struct mutex mbox_mutex; /* mutex to protect mailbox */
> +	struct clk *ref_clk;
> +	u32 ref_clk_rate;
> +	u32 num_lanes;
> +	u32 max_bit_rate; /* Maximum link bit rate to use (in Mbps) */
> +	u32 link_rate;
> +	bool power_up;
> +};
> +
> +static int cdns_phy_reg_write(struct cdns_hdptx_dp_phy *cdns_phy, u32 addr, u32 val)
> +{
> +	return cdns_mhdp_reg_write(cdns_phy, ADDR_PHY_AFE + (addr << 2), val);
> +}
> +
> +static u32 cdns_phy_reg_read(struct cdns_hdptx_dp_phy *cdns_phy, u32 addr)
> +{
> +	u32 reg32;
> +
> +	cdns_mhdp_reg_read(cdns_phy, ADDR_PHY_AFE + (addr << 2), &reg32);
> +	return reg32;
> +}
> +
> +static int link_rate_index(u32 rate)
> +{
> +	switch (rate) {
> +	case RATE_1_6:
> +		return 0;
> +	case RATE_2_1:
> +		return 1;
> +	case RATE_2_4:
> +		return 2;
> +	case RATE_2_7:
> +		return 3;
> +	case RATE_3_2:
> +		return 4;
> +	case RATE_4_3:
> +		return 5;
> +	case RATE_5_4:
> +		return 6;
> +	default:
> +		return -1;
> +	}
> +}
> +
> +static int hdptx_dp_ref_clk(struct cdns_hdptx_dp_phy *cdns_phy)
> +{
> +	struct device *dev = cdns_phy->dev;
> +	u32 ref_clk_rate;
> +	int ret;
> +
> +	cdns_phy->ref_clk = devm_clk_get(dev, "refclk");
> +	if (IS_ERR(cdns_phy->ref_clk)) {
> +		dev_err(dev, "phy ref clock not found\n");
> +		return PTR_ERR(cdns_phy->ref_clk);
> +	}
> +
> +	ret = clk_prepare_enable(cdns_phy->ref_clk);
> +	if (ret) {
> +		dev_err(cdns_phy->dev, "Failed to prepare ref clock\n");
> +		return ret;
> +	}
> +
> +	ref_clk_rate = clk_get_rate(cdns_phy->ref_clk);
> +	if (!ref_clk_rate) {
> +		dev_err(cdns_phy->dev, "Failed to get ref clock rate\n");
> +		goto err_ref_clk;
> +	}
> +
> +	if (ref_clk_rate == REF_CLK_27MHZ)
> +		cdns_phy->ref_clk_rate = ref_clk_rate;
> +	else {
> +		dev_err(cdns_phy->dev, "Not support Ref Clock Rate(%dHz)\n", ref_clk_rate);
> +		goto err_ref_clk;
> +	}
> +
> +	return 0;
> +
> +err_ref_clk:
> +	clk_disable_unprepare(cdns_phy->ref_clk);
> +	return -EINVAL;
> +}
> +
> +static void hdptx_dp_aux_cfg(struct cdns_hdptx_dp_phy *cdns_phy)
> +{
> +	/* Power up Aux */
> +	cdns_phy_reg_write(cdns_phy, TXDA_CYA_AUXDA_CYA, 1);
> +
> +	cdns_phy_reg_write(cdns_phy, TX_DIG_CTRL_REG_1, 0x3);
> +	ndelay(150);
> +	cdns_phy_reg_write(cdns_phy, TX_DIG_CTRL_REG_2, 36);
> +	ndelay(150);
> +	cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_2, 0x0100);
> +	ndelay(150);
> +	cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_2, 0x0300);
> +	ndelay(150);
> +	cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_3, 0x0000);
> +	ndelay(150);
> +	cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_1, 0x2008);
> +	ndelay(150);
> +	cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_1, 0x2018);
> +	ndelay(150);
> +	cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_1, 0xA018);
> +	ndelay(150);
> +	cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_2, 0x030C);
> +	ndelay(150);
> +	cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_5, 0x0000);
> +	ndelay(150);
> +	cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_4, 0x1001);
> +	ndelay(150);
> +	cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_1, 0xA098);
> +	ndelay(150);
> +	cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_1, 0xA198);
> +	ndelay(150);
> +	cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_2, 0x030d);
> +	ndelay(150);
> +	cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_2, 0x030f);
> +}
> +
> +/* PMA common configuration for 27MHz */
> +static void hdptx_dp_phy_pma_cmn_cfg_27mhz(struct cdns_hdptx_dp_phy *cdns_phy)
> +{
> +	u32 num_lanes = cdns_phy->num_lanes;
> +	u16 val;
> +	int k;
> +
> +	val = cdns_phy_reg_read(cdns_phy, PHY_PMA_CMN_CTRL1);
> +	val &= 0xFFF7;
> +	val |= 0x0008;
> +	cdns_phy_reg_write(cdns_phy, PHY_PMA_CMN_CTRL1, val);
> +
> +	/* Startup state machine registers */
> +	cdns_phy_reg_write(cdns_phy, CMN_SSM_BIAS_TMR, 0x0087);
> +	cdns_phy_reg_write(cdns_phy, CMN_PLLSM0_PLLEN_TMR, 0x001B);
> +	cdns_phy_reg_write(cdns_phy, CMN_PLLSM0_PLLPRE_TMR, 0x0036);
> +	cdns_phy_reg_write(cdns_phy, CMN_PLLSM0_PLLVREF_TMR, 0x001B);
> +	cdns_phy_reg_write(cdns_phy, CMN_PLLSM0_PLLLOCK_TMR, 0x006C);
> +
> +	/* Current calibration registers */
> +	cdns_phy_reg_write(cdns_phy, CMN_ICAL_INIT_TMR, 0x0044);
> +	cdns_phy_reg_write(cdns_phy, CMN_ICAL_ITER_TMR, 0x0006);
> +	cdns_phy_reg_write(cdns_phy, CMN_ICAL_ADJ_INIT_TMR, 0x0022);
> +	cdns_phy_reg_write(cdns_phy, CMN_ICAL_ADJ_ITER_TMR, 0x0006);
> +
> +	/* Resistor calibration registers */
> +	cdns_phy_reg_write(cdns_phy, CMN_TXPUCAL_INIT_TMR, 0x0022);
> +	cdns_phy_reg_write(cdns_phy, CMN_TXPUCAL_ITER_TMR, 0x0006);
> +	cdns_phy_reg_write(cdns_phy, CMN_TXPU_ADJ_INIT_TMR, 0x0022);
> +	cdns_phy_reg_write(cdns_phy, CMN_TXPU_ADJ_ITER_TMR, 0x0006);
> +	cdns_phy_reg_write(cdns_phy, CMN_TXPDCAL_INIT_TMR, 0x0022);
> +	cdns_phy_reg_write(cdns_phy, CMN_TXPDCAL_ITER_TMR, 0x0006);
> +	cdns_phy_reg_write(cdns_phy, CMN_TXPD_ADJ_INIT_TMR, 0x0022);
> +	cdns_phy_reg_write(cdns_phy, CMN_TXPD_ADJ_ITER_TMR, 0x0006);
> +	cdns_phy_reg_write(cdns_phy, CMN_RXCAL_INIT_TMR, 0x0022);
> +	cdns_phy_reg_write(cdns_phy, CMN_RXCAL_ITER_TMR, 0x0006);
> +	cdns_phy_reg_write(cdns_phy, CMN_RX_ADJ_INIT_TMR, 0x0022);
> +	cdns_phy_reg_write(cdns_phy, CMN_RX_ADJ_ITER_TMR, 0x0006);
> +
> +	for (k = 0; k < num_lanes; k = k + 1) {
> +		/* Power state machine registers */
> +		cdns_phy_reg_write(cdns_phy, XCVR_PSM_CAL_TMR  | (k << 9), 0x016D);
> +		cdns_phy_reg_write(cdns_phy, XCVR_PSM_A0IN_TMR | (k << 9), 0x016D);
> +		/* Transceiver control and diagnostic registers */
> +		cdns_phy_reg_write(cdns_phy, XCVR_DIAG_LANE_FCM_EN_MGN_TMR | (k << 9), 0x00A2);
> +		cdns_phy_reg_write(cdns_phy, TX_DIAG_BGREF_PREDRV_DELAY    | (k << 9), 0x0097);
> +		/* Transmitter receiver detect registers */
> +		cdns_phy_reg_write(cdns_phy, TX_RCVDET_EN_TMR | (k << 9), 0x0A8C);
> +		cdns_phy_reg_write(cdns_phy, TX_RCVDET_ST_TMR | (k << 9), 0x0036);
> +	}
> +
> +	cdns_phy_reg_write(cdns_phy, TX_DIAG_ACYA_0, 1);
> +	cdns_phy_reg_write(cdns_phy, TX_DIAG_ACYA_1, 1);
> +	cdns_phy_reg_write(cdns_phy, TX_DIAG_ACYA_2, 1);
> +	cdns_phy_reg_write(cdns_phy, TX_DIAG_ACYA_3, 1);
> +}
> +
> +static void hdptx_dp_phy_pma_cmn_pll0_27mhz(struct cdns_hdptx_dp_phy *cdns_phy)
> +{
> +	u32 num_lanes = cdns_phy->num_lanes;
> +	u32 link_rate = cdns_phy->link_rate;
> +	u16 val;
> +	int index, i, k;
> +
> +	/* DP PLL data rate 0/1 clock divider value */
> +	val = cdns_phy_reg_read(cdns_phy, PHY_HDP_CLK_CTL);
> +	val &= 0x00FF;
> +	if (link_rate <= RATE_2_7)
> +		val |= 0x2400;
> +	else
> +		val |= 0x1200;
> +	cdns_phy_reg_write(cdns_phy, PHY_HDP_CLK_CTL, val);
> +
> +	/* High speed clock 0/1 div */
> +	val = cdns_phy_reg_read(cdns_phy, CMN_DIAG_HSCLK_SEL);
> +	val &= 0xFFCC;
> +	if (link_rate <= RATE_2_7)
> +		val |= 0x0011;
> +	cdns_phy_reg_write(cdns_phy, CMN_DIAG_HSCLK_SEL, val);
> +
> +	for (k = 0; k < num_lanes; k++) {
> +		val = cdns_phy_reg_read(cdns_phy, (XCVR_DIAG_HSCLK_SEL | (k << 9)));
> +		val = val & 0xCFFF;
> +		if (link_rate <= RATE_2_7)
> +			val |= 0x1000;
> +		cdns_phy_reg_write(cdns_phy, (XCVR_DIAG_HSCLK_SEL | (k << 9)), val);
> +	}
> +
> +	/* DP PHY PLL 27MHz configuration */
> +	index = link_rate_index(link_rate);
> +	for (i = 0; i < ARRAY_SIZE(phy_pll_27m_cfg); i++)
> +		cdns_phy_reg_write(cdns_phy, phy_pll_27m_cfg[i].addr,
> +				phy_pll_27m_cfg[i].val[index]);
> +
> +	/* Transceiver control and diagnostic registers */
> +	for (k = 0; k < num_lanes; k++) {
> +		val = cdns_phy_reg_read(cdns_phy, (XCVR_DIAG_PLLDRC_CTRL | (k << 9)));
> +		val = val & 0x8FFF;
> +		if (link_rate <= RATE_2_7)
> +			val |= 0x2000;
> +		else
> +			val |= 0x1000;
> +		cdns_phy_reg_write(cdns_phy, (XCVR_DIAG_PLLDRC_CTRL | (k << 9)), val);
> +	}
> +
> +	for (k = 0; k < num_lanes; k = k + 1) {
> +		/* Power state machine registers */
> +		cdns_phy_reg_write(cdns_phy, (XCVR_PSM_RCTRL | (k << 9)),  0xBEFC);
> +		cdns_phy_reg_write(cdns_phy, (TX_PSC_A0 | (k << 9)), 0x6799);
> +		cdns_phy_reg_write(cdns_phy, (TX_PSC_A1 | (k << 9)), 0x6798);
> +		cdns_phy_reg_write(cdns_phy, (TX_PSC_A2 | (k << 9)), 0x0098);
> +		cdns_phy_reg_write(cdns_phy, (TX_PSC_A3 | (k << 9)), 0x0098);
> +		/* Receiver calibration power state definition register */
> +		val = cdns_phy_reg_read(cdns_phy, RX_PSC_CAL | (k << 9));
> +		val &= 0xFFBB;
> +		cdns_phy_reg_write(cdns_phy, (RX_PSC_CAL | (k << 9)), val);
> +		val = cdns_phy_reg_read(cdns_phy, RX_PSC_A0  | (k << 9));
> +		val &= 0xFFBB;
> +		cdns_phy_reg_write(cdns_phy, (RX_PSC_A0  | (k << 9)), val);
> +	}
> +}
> +
> +static void hdptx_dp_phy_ref_clock_type(struct cdns_hdptx_dp_phy *cdns_phy)
> +{
> +	u32 val;
> +
> +	val = cdns_phy_reg_read(cdns_phy, PHY_PMA_CMN_CTRL1);
> +	val &= 0xFF8F;
> +	/*
> +	 * single ended reference clock (val |= 0x0030);
> +	 * differential clock  (val |= 0x0000);
> +	 *
> +	 * for differential clock on the refclk_p and
> +	 * refclk_m off chip pins: CMN_DIAG_ACYA[8]=1'b1
> +	 * cdns_phy_reg_write(cdns_phy, CMN_DIAG_ACYA, 0x0100);
> +	 */
> +	val |= 0x0030;
> +	cdns_phy_reg_write(cdns_phy, PHY_PMA_CMN_CTRL1, val);
> +}
> +
> +static int hdptx_dp_phy_power_up(struct cdns_hdptx_dp_phy *cdns_phy)
> +{
> +	u32 val, i;
> +
> +	/* Enable HDP PLL’s for high speed clocks */
> +	val = cdns_phy_reg_read(cdns_phy, PHY_HDP_CLK_CTL);
> +	val |= (1 << 0);
> +	cdns_phy_reg_write(cdns_phy, PHY_HDP_CLK_CTL, val);
> +	/* Wait for PLL ready ACK */
> +	for (i = 0; i < 10; i++) {
> +		val = cdns_phy_reg_read(cdns_phy, PHY_HDP_CLK_CTL);
> +		if (val & (1 << 1))
> +			break;
> +		msleep(20);
> +	}
> +	if (i == 10) {
> +		dev_err(cdns_phy->dev, "Wait PLL Ack failed\n");
> +		return -1;
> +	}
> +
> +	/* Enable HDP PLL’s data rate and full rate clocks out of PMA. */
> +	val = cdns_phy_reg_read(cdns_phy, PHY_HDP_CLK_CTL);
> +	val |= (1 << 2);
> +	cdns_phy_reg_write(cdns_phy, PHY_HDP_CLK_CTL, val);
> +	/* Wait for PLL clock enable ACK */
> +	for (i = 0; i < 10; i++) {
> +		val = cdns_phy_reg_read(cdns_phy, PHY_HDP_CLK_CTL);
> +		if (val & (1 << 3))
> +			break;
> +		msleep(20);
> +	}
> +	if (i == 10) {
> +		dev_err(cdns_phy->dev, "Wait PLL clock enable ACk failed\n");
> +		return -1;
> +	}
> +
> +	/* Configure PHY in A2 Mode */
> +	cdns_phy_reg_write(cdns_phy, PHY_HDP_MODE_CTRL, 0x0004);
> +	/* Wait for Power State A2 Ack */
> +	for (i = 0; i < 10; i++) {
> +		val = cdns_phy_reg_read(cdns_phy, PHY_HDP_MODE_CTRL);
> +		if (val & (1 << 6))
> +			break;
> +		msleep(20);
> +	}
> +	if (i == 10) {
> +		dev_err(cdns_phy->dev, "Wait A2 Ack failed\n");
> +		return -1;
> +	}
> +
> +	/* Configure PHY in A0 mode (PHY must be in the A0 power
> +	 * state in order to transmit data)
> +	 */
> +	cdns_phy_reg_write(cdns_phy, PHY_HDP_MODE_CTRL, 0x0101);
> +
> +	/* Wait for Power State A0 Ack */
> +	for (i = 0; i < 10; i++) {
> +		val = cdns_phy_reg_read(cdns_phy, PHY_HDP_MODE_CTRL);
> +		if (val & (1 << 4))
> +			break;
> +		msleep(20);
> +	}
> +	if (i == 10) {
> +		dev_err(cdns_phy->dev, "Wait A0 Ack failed\n");
> +		return -1;
> +	}
> +
> +	cdns_phy->power_up = true;
> +
> +	return 0;
> +}
> +
> +static void hdptx_dp_phy_power_down(struct cdns_hdptx_dp_phy *cdns_phy)
> +{
> +	u16 val;
> +	int i;
> +
> +	if (!cdns_phy->power_up)
> +		return;
> +
> +	/* Place the PHY lanes in the A3 power state. */
> +	cdns_phy_reg_write(cdns_phy, PHY_HDP_MODE_CTRL, 0x8);
> +	/* Wait for Power State A3 Ack */
> +	for (i = 0; i < 10; i++) {
> +		val = cdns_phy_reg_read(cdns_phy, PHY_HDP_MODE_CTRL);
> +		if (val & (1 << 7))
> +			break;
> +		msleep(20);
> +	}
> +	if (i == 10) {
> +		dev_err(cdns_phy->dev, "Wait A3 Ack failed\n");
> +		return;
> +	}
> +
> +	/* Disable HDP PLL’s data rate and full rate clocks out of PMA. */
> +	val = cdns_phy_reg_read(cdns_phy, PHY_HDP_CLK_CTL);
> +	val &= ~(1 << 2);
> +	cdns_phy_reg_write(cdns_phy, PHY_HDP_CLK_CTL, val);
> +	/* Wait for PLL clock gate ACK */
> +	for (i = 0; i < 10; i++) {
> +		val = cdns_phy_reg_read(cdns_phy, PHY_HDP_CLK_CTL);
> +		if (!(val & (1 << 3)))
> +			break;
> +		msleep(20);
> +	}
> +	if (i == 10) {
> +		dev_err(cdns_phy->dev, "Wait PLL clock gate Ack failed\n");
> +		return;
> +	}
> +
> +	/* Disable HDP PLL’s for high speed clocks */
> +	val = cdns_phy_reg_read(cdns_phy, PHY_HDP_CLK_CTL);
> +	val &= ~(1 << 0);
> +	cdns_phy_reg_write(cdns_phy, PHY_HDP_CLK_CTL, val);
> +	/* Wait for PLL disable ACK */
> +	for (i = 0; i < 10; i++) {
> +		val = cdns_phy_reg_read(cdns_phy, PHY_HDP_CLK_CTL);
> +		if (!(val & (1 << 1)))
> +			break;
> +		msleep(20);
> +	}
> +	if (i == 10) {
> +		dev_err(cdns_phy->dev, "Wait PLL disable Ack failed\n");
> +		return;
> +	}
> +}
> +
> +static int cdns_hdptx_dp_phy_on(struct phy *phy)
> +{
> +	struct cdns_hdptx_dp_phy *cdns_phy = phy_get_drvdata(phy);
> +
> +	return hdptx_dp_phy_power_up(cdns_phy);
> +}
> +
> +static int cdns_hdptx_dp_phy_off(struct phy *phy)
> +{
> +	struct cdns_hdptx_dp_phy *cdns_phy = phy_get_drvdata(phy);
> +
> +	hdptx_dp_phy_power_down(cdns_phy);
> +
> +	return 0;
> +}
> +
> +static int cdns_hdptx_dp_phy_init(struct phy *phy)
> +{
> +	struct cdns_hdptx_dp_phy *cdns_phy = phy_get_drvdata(phy);
> +	int ret;
> +
> +	hdptx_dp_phy_ref_clock_type(cdns_phy);
> +
> +	/* PHY power up */
> +	ret = hdptx_dp_phy_power_up(cdns_phy);
> +	if (ret < 0)
> +		return ret;
> +
> +	hdptx_dp_aux_cfg(cdns_phy);
> +
> +	return ret;
> +}
> +
> +static int cdns_hdptx_dp_configure(struct phy *phy,
> +				     union phy_configure_opts *opts)
> +{
> +	struct cdns_hdptx_dp_phy *cdns_phy = phy_get_drvdata(phy);
> +	int ret;
> +
> +	cdns_phy->link_rate = opts->dp.link_rate;
> +
> +	/* Disable phy clock if PHY in power up state */
> +	hdptx_dp_phy_power_down(cdns_phy);
> +
> +	if (cdns_phy->ref_clk_rate == REF_CLK_27MHZ) {
> +		hdptx_dp_phy_pma_cmn_cfg_27mhz(cdns_phy);
> +		hdptx_dp_phy_pma_cmn_pll0_27mhz(cdns_phy);
> +	} else
> +		dev_err(cdns_phy->dev, "Not support ref clock rate\n");
> +
> +	/* PHY power up */
> +	ret = hdptx_dp_phy_power_up(cdns_phy);
> +
> +	return ret;
> +}
> +
> +static const struct phy_ops cdns_hdptx_dp_phy_ops = {
> +	.init		= cdns_hdptx_dp_phy_init,
> +	.configure	= cdns_hdptx_dp_configure,
> +	.power_on	= cdns_hdptx_dp_phy_on,
> +	.power_off	= cdns_hdptx_dp_phy_off,
> +	.owner		= THIS_MODULE,
> +};
> +
> +static int cdns_hdptx_dp_phy_probe(struct platform_device *pdev)
> +{
> +	struct cdns_hdptx_dp_phy *cdns_phy;
> +	struct device *dev = &pdev->dev;
> +	struct device_node *node = dev->of_node;
> +	struct phy_provider *phy_provider;
> +	struct resource *res;
> +	struct phy *phy;
> +	int ret;
> +
> +	cdns_phy = devm_kzalloc(dev, sizeof(*cdns_phy), GFP_KERNEL);
> +	if (!cdns_phy)
> +		return -ENOMEM;
> +
> +	dev_set_drvdata(dev, cdns_phy);
> +	cdns_phy->dev = dev;
> +	mutex_init(&cdns_phy->mbox_mutex);
> +
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	if (!res)
> +		return -ENODEV;
> +	cdns_phy->regs = devm_ioremap(dev, res->start, resource_size(res));
> +	if (IS_ERR(cdns_phy->regs))
> +		return PTR_ERR(cdns_phy->regs);
> +
> +	if (of_property_read_u32(node, "cdns,num-lanes",
> +				 &cdns_phy->num_lanes)) {
> +		dev_err(dev, "%s: No \"cdns,num-lanes\"-property.\n",
> +			node->full_name);
> +		return -EINVAL;
> +	}
> +
> +	phy = devm_phy_create(dev, node, &cdns_hdptx_dp_phy_ops);
> +	if (IS_ERR(phy))
> +		return PTR_ERR(phy);
> +
> +	cdns_phy->max_bit_rate = DEFAULT_MAX_BIT_RATE;
> +	of_property_read_u32(node, "cdns,max-bit-rate",
> +			     &cdns_phy->max_bit_rate);
> +
> +	switch (cdns_phy->max_bit_rate) {
> +	/* valid bit rate */
> +	case 1620:
> +	case 2160:
> +	case 2430:
> +	case 2700:
> +	case 3240:
> +	case 4320:
> +	case 5400:
> +		break;
> +	case 8100:
> +	default:
> +		dev_err(dev, "unsupported max bit rate: %dMbps\n",
> +				cdns_phy->max_bit_rate);
> +		return -EINVAL;
> +	}
> +
> +	dev_dbg(dev, "DP max bit rate %d.%03d Gbps\n",
> +		cdns_phy->max_bit_rate / 1000,
> +		cdns_phy->max_bit_rate % 1000);
> +
> +	phy->attrs.bus_width = cdns_phy->num_lanes;
> +	phy->attrs.max_link_rate = cdns_phy->max_bit_rate;
> +	phy->attrs.mode = PHY_MODE_DP;
> +
> +	cdns_phy->phy = phy;
> +	phy_set_drvdata(phy, cdns_phy);
> +
> +	if (cdns_phy->num_lanes > MAX_NUM_LANES) {
> +		dev_err(dev, "Invalid lane configuration\n");
> +		return -EINVAL;
> +	}
> +
> +	ret = hdptx_dp_ref_clk(cdns_phy);
> +	if (ret) {
> +		dev_err(dev, "Init clk fail\n");
> +		return -EINVAL;
> +	}
> +
> +	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
> +	if (IS_ERR(phy_provider)) {
> +		ret =  PTR_ERR(phy_provider);
> +		goto clk_disable;
> +	}
> +
> +	dev_dbg(dev, "link: (%d lanes)", cdns_phy->num_lanes);
> +
> +	return 0;
> +
> +clk_disable:
> +	clk_disable_unprepare(cdns_phy->ref_clk);
> +
> +	return -EINVAL;
> +}
> +
> +static int cdns_hdptx_dp_phy_remove(struct platform_device *pdev)
> +{
> +	struct cdns_hdptx_dp_phy *cdns_phy = platform_get_drvdata(pdev);
> +
> +	clk_disable_unprepare(cdns_phy->ref_clk);
> +
> +	return 0;
> +}
> +
> +static const struct of_device_id cdns_hdptx_dp_phy_of_match[] = {
> +	{
> +		.compatible = "cdns,hdptx-dp-phy",
> +	},
> +	{}
> +};
> +MODULE_DEVICE_TABLE(of, cdns_hdptx_dp_phy_of_match);
> +
> +static struct platform_driver cdns_hdptx_dp_phy_driver = {
> +	.probe	= cdns_hdptx_dp_phy_probe,
> +	.remove = cdns_hdptx_dp_phy_remove,
> +	.driver = {
> +		.name	= "cdns-hdptx-dp-phy",
> +		.of_match_table	= cdns_hdptx_dp_phy_of_match,
> +	}
> +};
> +module_platform_driver(cdns_hdptx_dp_phy_driver);
> +
> +MODULE_AUTHOR("Sandor Yu <sandor.yu@nxp.com>");
> +MODULE_DESCRIPTION("Cadence HDP-TX DisplayPort PHY driver");
> +MODULE_LICENSE("GPL");
> -- 
> 2.34.1
  
Sandor Yu Nov. 10, 2022, 8:10 a.m. UTC | #2
Thanks your comments,

> -----Original Message-----
> From: Vinod Koul <vkoul@kernel.org>
> Sent: 2022年11月10日 15:41
> To: Sandor Yu <sandor.yu@nxp.com>
> Cc: dri-devel@lists.freedesktop.org; devicetree@vger.kernel.org;
> linux-arm-kernel@lists.infradead.org; linux-kernel@vger.kernel.org;
> linux-phy@lists.infradead.org; andrzej.hajda@intel.com;
> neil.armstrong@linaro.org; robert.foss@linaro.org;
> Laurent.pinchart@ideasonboard.com; jonas@kwiboo.se;
> jernej.skrabec@gmail.com; robh+dt@kernel.org;
> krzysztof.kozlowski+dt@linaro.org; shawnguo@kernel.org;
> s.hauer@pengutronix.de; kernel@pengutronix.de; dl-linux-imx
> <linux-imx@nxp.com>; tzimmermann@suse.de; lyude@redhat.com;
> javierm@redhat.com; ville.syrjala@linux.intel.com; sam@ravnborg.org;
> jani.nikula@intel.com; maxime@cerno.tech;
> penguin-kernel@i-love.sakura.ne.jp; Oliver Brown <oliver.brown@nxp.com>
> Subject: [EXT] Re: [PATCH v3 08/10] phy: cadence: Add driver for HDP-TX
> DisplyPort PHY
> 
> Caution: EXT Email
> 
> On 08-11-22, 21:00, Sandor Yu wrote:
> > Add Cadence HDP-TX DisplayPort PHY driver.
> >
> > Cadence HDP-TX PHY could be put in either DP mode or HDMI mode base
> on
> > the configuration chosen.
> > DisplayPort PHY mode is configurated in the driver.
> >
> > Signed-off-by: Sandor Yu <Sandor.yu@nxp.com>
> > ---
> >  drivers/phy/cadence/Kconfig                |   8 +
> >  drivers/phy/cadence/Makefile               |   1 +
> >  drivers/phy/cadence/phy-cadence-hdptx-dp.c | 774
> > +++++++++++++++++++++
> >  3 files changed, 783 insertions(+)
> >  create mode 100644 drivers/phy/cadence/phy-cadence-hdptx-dp.c
> >
> > diff --git a/drivers/phy/cadence/Kconfig b/drivers/phy/cadence/Kconfig
> > index 1adde2d99ae7..1e1914d3afdc 100644
> > --- a/drivers/phy/cadence/Kconfig
> > +++ b/drivers/phy/cadence/Kconfig
> > @@ -46,3 +46,11 @@ config PHY_CADENCE_SALVO
> >         Enable this to support the Cadence SALVO PHY driver,
> >         this PHY is a legacy PHY, and only are used for USB3
> >         and USB2.
> > +
> > +config PHY_CADENCE_HDPTX_DP
> 
> alphabetically sorted please
OK.
> 
> > +     tristate "Cadence HDPTX DP PHY Driver"
> > +     depends on OF && HAS_IOMEM
> > +     depends on COMMON_CLK
> > +     select GENERIC_PHY
> > +     help
> > +       Enable this to support the Cadence HDPTX DP PHY driver
> > diff --git a/drivers/phy/cadence/Makefile
> > b/drivers/phy/cadence/Makefile index e17f035ddece..fbdb0bc5ff11 100644
> > --- a/drivers/phy/cadence/Makefile
> > +++ b/drivers/phy/cadence/Makefile
> > @@ -4,3 +4,4 @@ obj-$(CONFIG_PHY_CADENCE_DPHY)        +=
> cdns-dphy.o
> >  obj-$(CONFIG_PHY_CADENCE_DPHY_RX)    += cdns-dphy-rx.o
> >  obj-$(CONFIG_PHY_CADENCE_SIERRA)     += phy-cadence-sierra.o
> >  obj-$(CONFIG_PHY_CADENCE_SALVO)      += phy-cadence-salvo.o
> > +obj-$(CONFIG_PHY_CADENCE_HDPTX_DP)   += phy-cadence-hdptx-dp.o
> 
> here too
OK.
> 
> > diff --git a/drivers/phy/cadence/phy-cadence-hdptx-dp.c
> > b/drivers/phy/cadence/phy-cadence-hdptx-dp.c
> > new file mode 100644
> > index 000000000000..079d43772d1d
> > --- /dev/null
> > +++ b/drivers/phy/cadence/phy-cadence-hdptx-dp.c
> > @@ -0,0 +1,774 @@
> > +// SPDX-License-Identifier: GPL-2.0-only
> > +/*
> > + * Cadence HDP-TX Display Port Interface (DP) PHY driver
> > + *
> > + * Copyright (C) 2022 NXP Semiconductor, Inc.
> > + */
> > +#include <asm/unaligned.h>
> > +#include <linux/clk.h>
> > +#include <linux/kernel.h>
> > +#include <linux/phy/phy.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/io.h>
> > +#include <linux/iopoll.h>
> > +
> > +#include <drm/bridge/cdns-mhdp-mailbox.h>
> > +
> > +#define ADDR_PHY_AFE 0x80000
> > +
> > +/* PHY registers */
> > +#define CMN_SSM_BIAS_TMR                0x0022
> > +#define CMN_PLLSM0_PLLEN_TMR            0x0029
> > +#define CMN_PLLSM0_PLLPRE_TMR           0x002A
> > +#define CMN_PLLSM0_PLLVREF_TMR          0x002B
> > +#define CMN_PLLSM0_PLLLOCK_TMR          0x002C
> > +#define CMN_PLLSM0_USER_DEF_CTRL        0x002F
> > +#define CMN_PSM_CLK_CTRL                0x0061
> > +#define CMN_CDIAG_REFCLK_CTRL           0x0062
> > +#define CMN_PLL0_VCOCAL_START           0x0081
> > +#define CMN_PLL0_VCOCAL_INIT_TMR        0x0084
> > +#define CMN_PLL0_VCOCAL_ITER_TMR        0x0085
> > +#define CMN_PLL0_INTDIV                 0x0094
> > +#define CMN_PLL0_FRACDIV                0x0095
> > +#define CMN_PLL0_HIGH_THR               0x0096
> > +#define CMN_PLL0_DSM_DIAG               0x0097
> > +#define CMN_PLL0_SS_CTRL1               0x0098
> > +#define CMN_PLL0_SS_CTRL2               0x0099
> > +#define CMN_ICAL_INIT_TMR               0x00C4
> > +#define CMN_ICAL_ITER_TMR               0x00C5
> > +#define CMN_RXCAL_INIT_TMR              0x00D4
> > +#define CMN_RXCAL_ITER_TMR              0x00D5
> > +#define CMN_TXPUCAL_CTRL                0x00E0
> > +#define CMN_TXPUCAL_INIT_TMR            0x00E4
> > +#define CMN_TXPUCAL_ITER_TMR            0x00E5
> > +#define CMN_TXPDCAL_CTRL                0x00F0
> > +#define CMN_TXPDCAL_INIT_TMR            0x00F4
> > +#define CMN_TXPDCAL_ITER_TMR            0x00F5
> > +#define CMN_ICAL_ADJ_INIT_TMR           0x0102
> > +#define CMN_ICAL_ADJ_ITER_TMR           0x0103
> > +#define CMN_RX_ADJ_INIT_TMR             0x0106
> > +#define CMN_RX_ADJ_ITER_TMR             0x0107
> > +#define CMN_TXPU_ADJ_CTRL               0x0108
> > +#define CMN_TXPU_ADJ_INIT_TMR           0x010A
> > +#define CMN_TXPU_ADJ_ITER_TMR           0x010B
> > +#define CMN_TXPD_ADJ_CTRL               0x010c
> > +#define CMN_TXPD_ADJ_INIT_TMR           0x010E
> > +#define CMN_TXPD_ADJ_ITER_TMR           0x010F
> > +#define CMN_DIAG_PLL0_FBH_OVRD          0x01C0
> > +#define CMN_DIAG_PLL0_FBL_OVRD          0x01C1
> > +#define CMN_DIAG_PLL0_OVRD              0x01C2
> > +#define CMN_DIAG_PLL0_TEST_MODE         0x01C4
> > +#define CMN_DIAG_PLL0_V2I_TUNE          0x01C5
> > +#define CMN_DIAG_PLL0_CP_TUNE           0x01C6
> > +#define CMN_DIAG_PLL0_LF_PROG           0x01C7
> > +#define CMN_DIAG_PLL0_PTATIS_TUNE1      0x01C8
> > +#define CMN_DIAG_PLL0_PTATIS_TUNE2      0x01C9
> > +#define CMN_DIAG_PLL0_INCLK_CTRL        0x01CA
> > +#define CMN_DIAG_PLL0_PXL_DIVH          0x01CB
> > +#define CMN_DIAG_PLL0_PXL_DIVL          0x01CC
> > +#define CMN_DIAG_HSCLK_SEL              0x01E0
> > +#define CMN_DIAG_PER_CAL_ADJ            0x01EC
> > +#define CMN_DIAG_CAL_CTRL               0x01ED
> > +#define CMN_DIAG_ACYA                   0x01FF
> > +#define XCVR_PSM_RCTRL                  0x4001
> > +#define XCVR_PSM_CAL_TMR                0x4002
> > +#define XCVR_PSM_A0IN_TMR               0x4003
> > +#define TX_TXCC_CAL_SCLR_MULT_0         0x4047
> > +#define TX_TXCC_CPOST_MULT_00_0         0x404C
> > +#define TX_TXCC_MGNFS_MULT_000_0        0x4050
> > +#define XCVR_DIAG_PLLDRC_CTRL           0x40E0
> > +#define XCVR_DIAG_PLLDRC_CTRL           0x40E0
> > +#define XCVR_DIAG_HSCLK_SEL             0x40E1
> > +#define XCVR_DIAG_BIDI_CTRL             0x40E8
> > +#define XCVR_DIAG_LANE_FCM_EN_MGN_TMR   0x40F2
> > +#define XCVR_DIAG_LANE_FCM_EN_MGN       0x40F2
> > +#define TX_PSC_A0                       0x4100
> > +#define TX_PSC_A1                       0x4101
> > +#define TX_PSC_A2                       0x4102
> > +#define TX_PSC_A3                       0x4103
> > +#define TX_RCVDET_CTRL                  0x4120
> > +#define TX_RCVDET_EN_TMR                0x4122
> > +#define TX_RCVDET_EN_TMR                0x4122
> > +#define TX_RCVDET_ST_TMR                0x4123
> > +#define TX_RCVDET_ST_TMR                0x4123
> > +#define TX_BIST_CTRL                    0x4140
> > +#define TX_BIST_UDDWR                   0x4141
> > +#define TX_DIAG_TX_CTRL                 0x41E0
> > +#define TX_DIAG_TX_DRV                  0x41E1
> > +#define TX_DIAG_BGREF_PREDRV_DELAY      0x41E7
> > +#define TX_DIAG_BGREF_PREDRV_DELAY      0x41E7
> > +#define XCVR_PSM_RCTRL_1                0x4201
> > +#define TX_TXCC_CAL_SCLR_MULT_1         0x4247
> > +#define TX_TXCC_CPOST_MULT_00_1         0x424C
> > +#define TX_TXCC_MGNFS_MULT_000_1        0x4250
> > +#define XCVR_DIAG_PLLDRC_CTRL_1         0x42E0
> > +#define XCVR_DIAG_HSCLK_SEL_1           0x42E1
> > +#define XCVR_DIAG_LANE_FCM_EN_MGN_TMR_1 0x42F2
> > +#define TX_RCVDET_EN_TMR_1              0x4322
> > +#define TX_RCVDET_ST_TMR_1              0x4323
> > +#define TX_DIAG_ACYA_0                  0x41FF
> > +#define TX_DIAG_ACYA_1                  0x43FF
> > +#define TX_DIAG_ACYA_2                  0x45FF
> > +#define TX_DIAG_ACYA_3                  0x47FF
> > +#define TX_ANA_CTRL_REG_1               0x5020
> > +#define TX_ANA_CTRL_REG_2               0x5021
> > +#define TXDA_COEFF_CALC                 0x5022
> > +#define TX_DIG_CTRL_REG_1               0x5023
> > +#define TX_DIG_CTRL_REG_2               0x5024
> > +#define TXDA_CYA_AUXDA_CYA              0x5025
> > +#define TX_ANA_CTRL_REG_3               0x5026
> > +#define TX_ANA_CTRL_REG_4               0x5027
> > +#define TX_ANA_CTRL_REG_5               0x5029
> > +#define RX_PSC_A0                       0x8000
> > +#define RX_PSC_CAL                      0x8006
> > +#define PMA_LANE_CFG                    0xC000
> > +#define PIPE_CMN_CTRL1                  0xC001
> > +#define PIPE_CMN_CTRL2                  0xC002
> > +#define PIPE_COM_LOCK_CFG1              0xC003
> > +#define PIPE_COM_LOCK_CFG2              0xC004
> > +#define PIPE_RCV_DET_INH                0xC005
> > +#define PHY_HDP_MODE_CTRL               0xC008
> > +#define PHY_HDP_CLK_CTL                 0xC009
> > +#define STS                             0xC00F
> > +#define PHY_ISO_CMN_CTRL                0xC010
> > +#define PHY_ISO_CMN_CTRL                0xC010
> > +#define PHY_HDP_TX_CTL_L0               0xC408
> > +#define PHY_DP_TX_CTL                   0xC408
> > +#define PHY_HDP_TX_CTL_L1               0xC448
> > +#define PHY_HDP_TX_CTL_L2               0xC488
> > +#define PHY_HDP_TX_CTL_L3               0xC4C8
> > +#define PHY_PMA_CMN_CTRL1               0xC800
> > +#define PMA_CMN_CTRL1                   0xC800
> > +#define PHY_PMA_ISO_CMN_CTRL            0xC810
> > +#define PHY_PMA_ISO_PLL_CTRL1           0xC812
> > +#define PHY_PMA_ISOLATION_CTRL          0xC81F
> > +#define PHY_ISOLATION_CTRL              0xC81F
> > +#define PHY_PMA_ISO_XCVR_CTRL           0xCC11
> > +#define PHY_PMA_ISO_LINK_MODE           0xCC12
> > +#define PHY_PMA_ISO_PWRST_CTRL          0xCC13
> > +#define PHY_PMA_ISO_TX_DATA_LO          0xCC14
> > +#define PHY_PMA_ISO_TX_DATA_HI          0xCC15
> > +#define PHY_PMA_ISO_RX_DATA_LO          0xCC16
> > +#define PHY_PMA_ISO_RX_DATA_HI          0xCC17
> 
> do you use all these?
I will remove unused later.
> 
> > +
> > +#define MAX_NUM_LANES                4
> > +#define DEFAULT_MAX_BIT_RATE 5400 /* in Mbps */
> > +
> > +#define REF_CLK_27MHZ                27000000
> > +
> > +enum dp_link_rate {
> > +     RATE_1_6 = 162000,
> > +     RATE_2_1 = 216000,
> > +     RATE_2_4 = 243000,
> > +     RATE_2_7 = 270000,
> > +     RATE_3_2 = 324000,
> > +     RATE_4_3 = 432000,
> > +     RATE_5_4 = 540000,
> > +     RATE_8_1 = 810000,
> > +};
> > +
> > +struct phy_pll_reg {
> > +     u16 val[7];
> > +     u32 addr;
> > +};
> > +
> > +static const struct phy_pll_reg phy_pll_27m_cfg[] = {
> > +     /*  1.62    2.16    2.43    2.7     3.24    4.32    5.4
> register address */
> > +     {{ 0x010E, 0x010E, 0x010E, 0x010E, 0x010E, 0x010E, 0x010E },
> CMN_PLL0_VCOCAL_INIT_TMR },
> > +     {{ 0x001B, 0x001B, 0x001B, 0x001B, 0x001B, 0x001B, 0x001B },
> CMN_PLL0_VCOCAL_ITER_TMR },
> > +     {{ 0x30B9, 0x3087, 0x3096, 0x30B4, 0x30B9, 0x3087, 0x30B4 },
> CMN_PLL0_VCOCAL_START },
> > +     {{ 0x0077, 0x009F, 0x00B3, 0x00C7, 0x0077, 0x009F, 0x00C7 },
> CMN_PLL0_INTDIV },
> > +     {{ 0xF9DA, 0xF7CD, 0xF6C7, 0xF5C1, 0xF9DA, 0xF7CD, 0xF5C1 },
> CMN_PLL0_FRACDIV },
> > +     {{ 0x001E, 0x0028, 0x002D, 0x0032, 0x001E, 0x0028, 0x0032 },
> CMN_PLL0_HIGH_THR },
> > +     {{ 0x0020, 0x0020, 0x0020, 0x0020, 0x0020, 0x0020, 0x0020 },
> CMN_PLL0_DSM_DIAG },
> > +     {{ 0x0000, 0x1000, 0x1000, 0x1000, 0x0000, 0x1000, 0x1000 },
> CMN_PLLSM0_USER_DEF_CTRL },
> > +     {{ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000 },
> CMN_DIAG_PLL0_OVRD },
> > +     {{ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000 },
> CMN_DIAG_PLL0_FBH_OVRD },
> > +     {{ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000 },
> CMN_DIAG_PLL0_FBL_OVRD },
> > +     {{ 0x0006, 0x0007, 0x0007, 0x0007, 0x0006, 0x0007, 0x0007 },
> CMN_DIAG_PLL0_V2I_TUNE },
> > +     {{ 0x0043, 0x0043, 0x0043, 0x0042, 0x0043, 0x0043, 0x0042 },
> CMN_DIAG_PLL0_CP_TUNE },
> > +     {{ 0x0008, 0x0008, 0x0008, 0x0008, 0x0008, 0x0008, 0x0008 },
> CMN_DIAG_PLL0_LF_PROG },
> > +     {{ 0x0100, 0x0001, 0x0001, 0x0001, 0x0100, 0x0001, 0x0001 },
> CMN_DIAG_PLL0_PTATIS_TUNE1 },
> > +     {{ 0x0007, 0x0001, 0x0001, 0x0001, 0x0007, 0x0001, 0x0001 },
> CMN_DIAG_PLL0_PTATIS_TUNE2 },
> > +     {{ 0x0020, 0x0020, 0x0020, 0x0020, 0x0020, 0x0020, 0x0020 },
> CMN_DIAG_PLL0_TEST_MODE},
> > +     {{ 0x0016, 0x0016, 0x0016, 0x0016, 0x0016, 0x0016, 0x0016 },
> > +CMN_PSM_CLK_CTRL } };
> > +
> > +struct cdns_hdptx_dp_phy {
> > +     void __iomem *regs;     /* DPTX registers base */
> > +     struct device *dev;
> > +     struct phy *phy;
> > +     struct mutex mbox_mutex; /* mutex to protect mailbox */
> > +     struct clk *ref_clk;
> > +     u32 ref_clk_rate;
> > +     u32 num_lanes;
> > +     u32 max_bit_rate; /* Maximum link bit rate to use (in Mbps) */
> > +     u32 link_rate;
> > +     bool power_up;
> > +};
> > +
> > +static int cdns_phy_reg_write(struct cdns_hdptx_dp_phy *cdns_phy, u32
> > +addr, u32 val) {
> > +     return cdns_mhdp_reg_write(cdns_phy, ADDR_PHY_AFE + (addr <<
> 2),
> > +val); }
> > +
> > +static u32 cdns_phy_reg_read(struct cdns_hdptx_dp_phy *cdns_phy, u32
> > +addr) {
> > +     u32 reg32;
> > +
> > +     cdns_mhdp_reg_read(cdns_phy, ADDR_PHY_AFE + (addr << 2),
> &reg32);
> > +     return reg32;
> > +}
> > +
> > +static int link_rate_index(u32 rate)
> > +{
> > +     switch (rate) {
> > +     case RATE_1_6:
> > +             return 0;
> > +     case RATE_2_1:
> > +             return 1;
> > +     case RATE_2_4:
> > +             return 2;
> > +     case RATE_2_7:
> > +             return 3;
> > +     case RATE_3_2:
> > +             return 4;
> > +     case RATE_4_3:
> > +             return 5;
> > +     case RATE_5_4:
> > +             return 6;
> > +     default:
> > +             return -1;
> > +     }
> > +}
> > +
> > +static int hdptx_dp_ref_clk(struct cdns_hdptx_dp_phy *cdns_phy) {
> > +     struct device *dev = cdns_phy->dev;
> > +     u32 ref_clk_rate;
> > +     int ret;
> > +
> > +     cdns_phy->ref_clk = devm_clk_get(dev, "refclk");
> > +     if (IS_ERR(cdns_phy->ref_clk)) {
> > +             dev_err(dev, "phy ref clock not found\n");
> > +             return PTR_ERR(cdns_phy->ref_clk);
> > +     }
> > +
> > +     ret = clk_prepare_enable(cdns_phy->ref_clk);
> > +     if (ret) {
> > +             dev_err(cdns_phy->dev, "Failed to prepare ref clock\n");
> > +             return ret;
> > +     }
> > +
> > +     ref_clk_rate = clk_get_rate(cdns_phy->ref_clk);
> > +     if (!ref_clk_rate) {
> > +             dev_err(cdns_phy->dev, "Failed to get ref clock rate\n");
> > +             goto err_ref_clk;
> > +     }
> > +
> > +     if (ref_clk_rate == REF_CLK_27MHZ)
> > +             cdns_phy->ref_clk_rate = ref_clk_rate;
> > +     else {
> > +             dev_err(cdns_phy->dev, "Not support Ref Clock
> Rate(%dHz)\n", ref_clk_rate);
> > +             goto err_ref_clk;
> > +     }
> > +
> > +     return 0;
> > +
> > +err_ref_clk:
> > +     clk_disable_unprepare(cdns_phy->ref_clk);
> > +     return -EINVAL;
> > +}
> > +
> > +static void hdptx_dp_aux_cfg(struct cdns_hdptx_dp_phy *cdns_phy) {
> > +     /* Power up Aux */
> > +     cdns_phy_reg_write(cdns_phy, TXDA_CYA_AUXDA_CYA, 1);
> > +
> > +     cdns_phy_reg_write(cdns_phy, TX_DIG_CTRL_REG_1, 0x3);
> > +     ndelay(150);
> > +     cdns_phy_reg_write(cdns_phy, TX_DIG_CTRL_REG_2, 36);
> > +     ndelay(150);
> > +     cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_2, 0x0100);
> > +     ndelay(150);
> > +     cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_2, 0x0300);
> > +     ndelay(150);
> > +     cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_3, 0x0000);
> > +     ndelay(150);
> > +     cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_1, 0x2008);
> > +     ndelay(150);
> > +     cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_1, 0x2018);
> > +     ndelay(150);
> > +     cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_1, 0xA018);
> > +     ndelay(150);
> > +     cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_2, 0x030C);
> > +     ndelay(150);
> > +     cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_5, 0x0000);
> > +     ndelay(150);
> > +     cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_4, 0x1001);
> > +     ndelay(150);
> > +     cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_1, 0xA098);
> > +     ndelay(150);
> > +     cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_1, 0xA198);
> > +     ndelay(150);
> > +     cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_2, 0x030d);
> > +     ndelay(150);
> > +     cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_2, 0x030f); }
> > +
> > +/* PMA common configuration for 27MHz */ static void
> > +hdptx_dp_phy_pma_cmn_cfg_27mhz(struct cdns_hdptx_dp_phy
> *cdns_phy) {
> > +     u32 num_lanes = cdns_phy->num_lanes;
> > +     u16 val;
> > +     int k;
> > +
> > +     val = cdns_phy_reg_read(cdns_phy, PHY_PMA_CMN_CTRL1);
> > +     val &= 0xFFF7;
> > +     val |= 0x0008;
> > +     cdns_phy_reg_write(cdns_phy, PHY_PMA_CMN_CTRL1, val);
> > +
> > +     /* Startup state machine registers */
> > +     cdns_phy_reg_write(cdns_phy, CMN_SSM_BIAS_TMR, 0x0087);
> > +     cdns_phy_reg_write(cdns_phy, CMN_PLLSM0_PLLEN_TMR,
> 0x001B);
> > +     cdns_phy_reg_write(cdns_phy, CMN_PLLSM0_PLLPRE_TMR,
> 0x0036);
> > +     cdns_phy_reg_write(cdns_phy, CMN_PLLSM0_PLLVREF_TMR,
> 0x001B);
> > +     cdns_phy_reg_write(cdns_phy, CMN_PLLSM0_PLLLOCK_TMR,
> 0x006C);
> > +
> > +     /* Current calibration registers */
> > +     cdns_phy_reg_write(cdns_phy, CMN_ICAL_INIT_TMR, 0x0044);
> > +     cdns_phy_reg_write(cdns_phy, CMN_ICAL_ITER_TMR, 0x0006);
> > +     cdns_phy_reg_write(cdns_phy, CMN_ICAL_ADJ_INIT_TMR,
> 0x0022);
> > +     cdns_phy_reg_write(cdns_phy, CMN_ICAL_ADJ_ITER_TMR,
> 0x0006);
> > +
> > +     /* Resistor calibration registers */
> > +     cdns_phy_reg_write(cdns_phy, CMN_TXPUCAL_INIT_TMR, 0x0022);
> > +     cdns_phy_reg_write(cdns_phy, CMN_TXPUCAL_ITER_TMR,
> 0x0006);
> > +     cdns_phy_reg_write(cdns_phy, CMN_TXPU_ADJ_INIT_TMR,
> 0x0022);
> > +     cdns_phy_reg_write(cdns_phy, CMN_TXPU_ADJ_ITER_TMR,
> 0x0006);
> > +     cdns_phy_reg_write(cdns_phy, CMN_TXPDCAL_INIT_TMR, 0x0022);
> > +     cdns_phy_reg_write(cdns_phy, CMN_TXPDCAL_ITER_TMR,
> 0x0006);
> > +     cdns_phy_reg_write(cdns_phy, CMN_TXPD_ADJ_INIT_TMR,
> 0x0022);
> > +     cdns_phy_reg_write(cdns_phy, CMN_TXPD_ADJ_ITER_TMR,
> 0x0006);
> > +     cdns_phy_reg_write(cdns_phy, CMN_RXCAL_INIT_TMR, 0x0022);
> > +     cdns_phy_reg_write(cdns_phy, CMN_RXCAL_ITER_TMR, 0x0006);
> > +     cdns_phy_reg_write(cdns_phy, CMN_RX_ADJ_INIT_TMR, 0x0022);
> > +     cdns_phy_reg_write(cdns_phy, CMN_RX_ADJ_ITER_TMR, 0x0006);
> > +
> > +     for (k = 0; k < num_lanes; k = k + 1) {
> > +             /* Power state machine registers */
> > +             cdns_phy_reg_write(cdns_phy, XCVR_PSM_CAL_TMR  |
> (k << 9), 0x016D);
> > +             cdns_phy_reg_write(cdns_phy, XCVR_PSM_A0IN_TMR |
> (k << 9), 0x016D);
> > +             /* Transceiver control and diagnostic registers */
> > +             cdns_phy_reg_write(cdns_phy,
> XCVR_DIAG_LANE_FCM_EN_MGN_TMR | (k << 9), 0x00A2);
> > +             cdns_phy_reg_write(cdns_phy,
> TX_DIAG_BGREF_PREDRV_DELAY    | (k << 9), 0x0097);
> > +             /* Transmitter receiver detect registers */
> > +             cdns_phy_reg_write(cdns_phy, TX_RCVDET_EN_TMR | (k
> << 9), 0x0A8C);
> > +             cdns_phy_reg_write(cdns_phy, TX_RCVDET_ST_TMR | (k
> << 9), 0x0036);
> > +     }
> > +
> > +     cdns_phy_reg_write(cdns_phy, TX_DIAG_ACYA_0, 1);
> > +     cdns_phy_reg_write(cdns_phy, TX_DIAG_ACYA_1, 1);
> > +     cdns_phy_reg_write(cdns_phy, TX_DIAG_ACYA_2, 1);
> > +     cdns_phy_reg_write(cdns_phy, TX_DIAG_ACYA_3, 1); }
> > +
> > +static void hdptx_dp_phy_pma_cmn_pll0_27mhz(struct
> cdns_hdptx_dp_phy
> > +*cdns_phy) {
> > +     u32 num_lanes = cdns_phy->num_lanes;
> > +     u32 link_rate = cdns_phy->link_rate;
> > +     u16 val;
> > +     int index, i, k;
> > +
> > +     /* DP PLL data rate 0/1 clock divider value */
> > +     val = cdns_phy_reg_read(cdns_phy, PHY_HDP_CLK_CTL);
> > +     val &= 0x00FF;
> > +     if (link_rate <= RATE_2_7)
> > +             val |= 0x2400;
> > +     else
> > +             val |= 0x1200;
> > +     cdns_phy_reg_write(cdns_phy, PHY_HDP_CLK_CTL, val);
> > +
> > +     /* High speed clock 0/1 div */
> > +     val = cdns_phy_reg_read(cdns_phy, CMN_DIAG_HSCLK_SEL);
> > +     val &= 0xFFCC;
> > +     if (link_rate <= RATE_2_7)
> > +             val |= 0x0011;
> > +     cdns_phy_reg_write(cdns_phy, CMN_DIAG_HSCLK_SEL, val);
> > +
> > +     for (k = 0; k < num_lanes; k++) {
> > +             val = cdns_phy_reg_read(cdns_phy,
> (XCVR_DIAG_HSCLK_SEL | (k << 9)));
> > +             val = val & 0xCFFF;
> > +             if (link_rate <= RATE_2_7)
> > +                     val |= 0x1000;
> > +             cdns_phy_reg_write(cdns_phy, (XCVR_DIAG_HSCLK_SEL |
> (k << 9)), val);
> > +     }
> > +
> > +     /* DP PHY PLL 27MHz configuration */
> > +     index = link_rate_index(link_rate);
> > +     for (i = 0; i < ARRAY_SIZE(phy_pll_27m_cfg); i++)
> > +             cdns_phy_reg_write(cdns_phy, phy_pll_27m_cfg[i].addr,
> > +                             phy_pll_27m_cfg[i].val[index]);
> > +
> > +     /* Transceiver control and diagnostic registers */
> > +     for (k = 0; k < num_lanes; k++) {
> > +             val = cdns_phy_reg_read(cdns_phy,
> (XCVR_DIAG_PLLDRC_CTRL | (k << 9)));
> > +             val = val & 0x8FFF;
> > +             if (link_rate <= RATE_2_7)
> > +                     val |= 0x2000;
> > +             else
> > +                     val |= 0x1000;
> > +             cdns_phy_reg_write(cdns_phy,
> (XCVR_DIAG_PLLDRC_CTRL | (k << 9)), val);
> > +     }
> > +
> > +     for (k = 0; k < num_lanes; k = k + 1) {
> > +             /* Power state machine registers */
> > +             cdns_phy_reg_write(cdns_phy, (XCVR_PSM_RCTRL | (k <<
> 9)),  0xBEFC);
> > +             cdns_phy_reg_write(cdns_phy, (TX_PSC_A0 | (k << 9)),
> 0x6799);
> > +             cdns_phy_reg_write(cdns_phy, (TX_PSC_A1 | (k << 9)),
> 0x6798);
> > +             cdns_phy_reg_write(cdns_phy, (TX_PSC_A2 | (k << 9)),
> 0x0098);
> > +             cdns_phy_reg_write(cdns_phy, (TX_PSC_A3 | (k << 9)),
> 0x0098);
> > +             /* Receiver calibration power state definition register */
> > +             val = cdns_phy_reg_read(cdns_phy, RX_PSC_CAL | (k <<
> 9));
> > +             val &= 0xFFBB;
> > +             cdns_phy_reg_write(cdns_phy, (RX_PSC_CAL | (k << 9)),
> val);
> > +             val = cdns_phy_reg_read(cdns_phy, RX_PSC_A0  | (k <<
> 9));
> > +             val &= 0xFFBB;
> > +             cdns_phy_reg_write(cdns_phy, (RX_PSC_A0  | (k << 9)),
> val);
> > +     }
> > +}
> > +
> > +static void hdptx_dp_phy_ref_clock_type(struct cdns_hdptx_dp_phy
> > +*cdns_phy) {
> > +     u32 val;
> > +
> > +     val = cdns_phy_reg_read(cdns_phy, PHY_PMA_CMN_CTRL1);
> > +     val &= 0xFF8F;
> > +     /*
> > +      * single ended reference clock (val |= 0x0030);
> > +      * differential clock  (val |= 0x0000);
> > +      *
> > +      * for differential clock on the refclk_p and
> > +      * refclk_m off chip pins: CMN_DIAG_ACYA[8]=1'b1
> > +      * cdns_phy_reg_write(cdns_phy, CMN_DIAG_ACYA, 0x0100);
> > +      */
> > +     val |= 0x0030;
> > +     cdns_phy_reg_write(cdns_phy, PHY_PMA_CMN_CTRL1, val); }
> > +
> > +static int hdptx_dp_phy_power_up(struct cdns_hdptx_dp_phy *cdns_phy)
> > +{
> > +     u32 val, i;
> > +
> > +     /* Enable HDP PLL’s for high speed clocks */
> > +     val = cdns_phy_reg_read(cdns_phy, PHY_HDP_CLK_CTL);
> > +     val |= (1 << 0);
> > +     cdns_phy_reg_write(cdns_phy, PHY_HDP_CLK_CTL, val);
> > +     /* Wait for PLL ready ACK */
> > +     for (i = 0; i < 10; i++) {
> > +             val = cdns_phy_reg_read(cdns_phy, PHY_HDP_CLK_CTL);
> > +             if (val & (1 << 1))
> > +                     break;
> > +             msleep(20);
> > +     }
> > +     if (i == 10) {
> > +             dev_err(cdns_phy->dev, "Wait PLL Ack failed\n");
> > +             return -1;
> > +     }
> > +
> > +     /* Enable HDP PLL’s data rate and full rate clocks out of PMA. */
> > +     val = cdns_phy_reg_read(cdns_phy, PHY_HDP_CLK_CTL);
> > +     val |= (1 << 2);
> > +     cdns_phy_reg_write(cdns_phy, PHY_HDP_CLK_CTL, val);
> > +     /* Wait for PLL clock enable ACK */
> > +     for (i = 0; i < 10; i++) {
> > +             val = cdns_phy_reg_read(cdns_phy, PHY_HDP_CLK_CTL);
> > +             if (val & (1 << 3))
> > +                     break;
> > +             msleep(20);
> > +     }
> > +     if (i == 10) {
> > +             dev_err(cdns_phy->dev, "Wait PLL clock enable ACk
> failed\n");
> > +             return -1;
> > +     }
> > +
> > +     /* Configure PHY in A2 Mode */
> > +     cdns_phy_reg_write(cdns_phy, PHY_HDP_MODE_CTRL, 0x0004);
> > +     /* Wait for Power State A2 Ack */
> > +     for (i = 0; i < 10; i++) {
> > +             val = cdns_phy_reg_read(cdns_phy,
> PHY_HDP_MODE_CTRL);
> > +             if (val & (1 << 6))
> > +                     break;
> > +             msleep(20);
> > +     }
> > +     if (i == 10) {
> > +             dev_err(cdns_phy->dev, "Wait A2 Ack failed\n");
> > +             return -1;
> > +     }
> > +
> > +     /* Configure PHY in A0 mode (PHY must be in the A0 power
> > +      * state in order to transmit data)
> > +      */
> > +     cdns_phy_reg_write(cdns_phy, PHY_HDP_MODE_CTRL, 0x0101);
> > +
> > +     /* Wait for Power State A0 Ack */
> > +     for (i = 0; i < 10; i++) {
> > +             val = cdns_phy_reg_read(cdns_phy,
> PHY_HDP_MODE_CTRL);
> > +             if (val & (1 << 4))
> > +                     break;
> > +             msleep(20);
> > +     }
> > +     if (i == 10) {
> > +             dev_err(cdns_phy->dev, "Wait A0 Ack failed\n");
> > +             return -1;
> > +     }
> > +
> > +     cdns_phy->power_up = true;
> > +
> > +     return 0;
> > +}
> > +
> > +static void hdptx_dp_phy_power_down(struct cdns_hdptx_dp_phy
> > +*cdns_phy) {
> > +     u16 val;
> > +     int i;
> > +
> > +     if (!cdns_phy->power_up)
> > +             return;
> > +
> > +     /* Place the PHY lanes in the A3 power state. */
> > +     cdns_phy_reg_write(cdns_phy, PHY_HDP_MODE_CTRL, 0x8);
> > +     /* Wait for Power State A3 Ack */
> > +     for (i = 0; i < 10; i++) {
> > +             val = cdns_phy_reg_read(cdns_phy,
> PHY_HDP_MODE_CTRL);
> > +             if (val & (1 << 7))
> > +                     break;
> > +             msleep(20);
> > +     }
> > +     if (i == 10) {
> > +             dev_err(cdns_phy->dev, "Wait A3 Ack failed\n");
> > +             return;
> > +     }
> > +
> > +     /* Disable HDP PLL’s data rate and full rate clocks out of PMA. */
> > +     val = cdns_phy_reg_read(cdns_phy, PHY_HDP_CLK_CTL);
> > +     val &= ~(1 << 2);
> > +     cdns_phy_reg_write(cdns_phy, PHY_HDP_CLK_CTL, val);
> > +     /* Wait for PLL clock gate ACK */
> > +     for (i = 0; i < 10; i++) {
> > +             val = cdns_phy_reg_read(cdns_phy, PHY_HDP_CLK_CTL);
> > +             if (!(val & (1 << 3)))
> > +                     break;
> > +             msleep(20);
> > +     }
> > +     if (i == 10) {
> > +             dev_err(cdns_phy->dev, "Wait PLL clock gate Ack
> failed\n");
> > +             return;
> > +     }
> > +
> > +     /* Disable HDP PLL’s for high speed clocks */
> > +     val = cdns_phy_reg_read(cdns_phy, PHY_HDP_CLK_CTL);
> > +     val &= ~(1 << 0);
> > +     cdns_phy_reg_write(cdns_phy, PHY_HDP_CLK_CTL, val);
> > +     /* Wait for PLL disable ACK */
> > +     for (i = 0; i < 10; i++) {
> > +             val = cdns_phy_reg_read(cdns_phy, PHY_HDP_CLK_CTL);
> > +             if (!(val & (1 << 1)))
> > +                     break;
> > +             msleep(20);
> > +     }
> > +     if (i == 10) {
> > +             dev_err(cdns_phy->dev, "Wait PLL disable Ack failed\n");
> > +             return;
> > +     }
> > +}
> > +
> > +static int cdns_hdptx_dp_phy_on(struct phy *phy) {
> > +     struct cdns_hdptx_dp_phy *cdns_phy = phy_get_drvdata(phy);
> > +
> > +     return hdptx_dp_phy_power_up(cdns_phy); }
> > +
> > +static int cdns_hdptx_dp_phy_off(struct phy *phy) {
> > +     struct cdns_hdptx_dp_phy *cdns_phy = phy_get_drvdata(phy);
> > +
> > +     hdptx_dp_phy_power_down(cdns_phy);
> > +
> > +     return 0;
> > +}
> > +
> > +static int cdns_hdptx_dp_phy_init(struct phy *phy) {
> > +     struct cdns_hdptx_dp_phy *cdns_phy = phy_get_drvdata(phy);
> > +     int ret;
> > +
> > +     hdptx_dp_phy_ref_clock_type(cdns_phy);
> > +
> > +     /* PHY power up */
> > +     ret = hdptx_dp_phy_power_up(cdns_phy);
> > +     if (ret < 0)
> > +             return ret;
> > +
> > +     hdptx_dp_aux_cfg(cdns_phy);
> > +
> > +     return ret;
> > +}
> > +
> > +static int cdns_hdptx_dp_configure(struct phy *phy,
> > +                                  union phy_configure_opts *opts)
> {
> > +     struct cdns_hdptx_dp_phy *cdns_phy = phy_get_drvdata(phy);
> > +     int ret;
> > +
> > +     cdns_phy->link_rate = opts->dp.link_rate;
> > +
> > +     /* Disable phy clock if PHY in power up state */
> > +     hdptx_dp_phy_power_down(cdns_phy);
> > +
> > +     if (cdns_phy->ref_clk_rate == REF_CLK_27MHZ) {
> > +             hdptx_dp_phy_pma_cmn_cfg_27mhz(cdns_phy);
> > +             hdptx_dp_phy_pma_cmn_pll0_27mhz(cdns_phy);
> > +     } else
> > +             dev_err(cdns_phy->dev, "Not support ref clock rate\n");
> > +
> > +     /* PHY power up */
> > +     ret = hdptx_dp_phy_power_up(cdns_phy);
> > +
> > +     return ret;
> > +}
> > +
> > +static const struct phy_ops cdns_hdptx_dp_phy_ops = {
> > +     .init           = cdns_hdptx_dp_phy_init,
> > +     .configure      = cdns_hdptx_dp_configure,
> > +     .power_on       = cdns_hdptx_dp_phy_on,
> > +     .power_off      = cdns_hdptx_dp_phy_off,
> > +     .owner          = THIS_MODULE,
> > +};
> > +
> > +static int cdns_hdptx_dp_phy_probe(struct platform_device *pdev) {
> > +     struct cdns_hdptx_dp_phy *cdns_phy;
> > +     struct device *dev = &pdev->dev;
> > +     struct device_node *node = dev->of_node;
> > +     struct phy_provider *phy_provider;
> > +     struct resource *res;
> > +     struct phy *phy;
> > +     int ret;
> > +
> > +     cdns_phy = devm_kzalloc(dev, sizeof(*cdns_phy), GFP_KERNEL);
> > +     if (!cdns_phy)
> > +             return -ENOMEM;
> > +
> > +     dev_set_drvdata(dev, cdns_phy);
> > +     cdns_phy->dev = dev;
> > +     mutex_init(&cdns_phy->mbox_mutex);
> > +
> > +     res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > +     if (!res)
> > +             return -ENODEV;
> > +     cdns_phy->regs = devm_ioremap(dev, res->start,
> resource_size(res));
> > +     if (IS_ERR(cdns_phy->regs))
> > +             return PTR_ERR(cdns_phy->regs);
> > +
> > +     if (of_property_read_u32(node, "cdns,num-lanes",
> > +                              &cdns_phy->num_lanes)) {
> > +             dev_err(dev, "%s: No \"cdns,num-lanes\"-property.\n",
> > +                     node->full_name);
> > +             return -EINVAL;
> > +     }
> > +
> > +     phy = devm_phy_create(dev, node, &cdns_hdptx_dp_phy_ops);
> > +     if (IS_ERR(phy))
> > +             return PTR_ERR(phy);
> > +
> > +     cdns_phy->max_bit_rate = DEFAULT_MAX_BIT_RATE;
> > +     of_property_read_u32(node, "cdns,max-bit-rate",
> > +                          &cdns_phy->max_bit_rate);
> > +
> > +     switch (cdns_phy->max_bit_rate) {
> > +     /* valid bit rate */
> > +     case 1620:
> > +     case 2160:
> > +     case 2430:
> > +     case 2700:
> > +     case 3240:
> > +     case 4320:
> > +     case 5400:
> > +             break;
> > +     case 8100:
> > +     default:
> > +             dev_err(dev, "unsupported max bit rate: %dMbps\n",
> > +                             cdns_phy->max_bit_rate);
> > +             return -EINVAL;
> > +     }
> > +
> > +     dev_dbg(dev, "DP max bit rate %d.%03d Gbps\n",
> > +             cdns_phy->max_bit_rate / 1000,
> > +             cdns_phy->max_bit_rate % 1000);
> > +
> > +     phy->attrs.bus_width = cdns_phy->num_lanes;
> > +     phy->attrs.max_link_rate = cdns_phy->max_bit_rate;
> > +     phy->attrs.mode = PHY_MODE_DP;
> > +
> > +     cdns_phy->phy = phy;
> > +     phy_set_drvdata(phy, cdns_phy);
> > +
> > +     if (cdns_phy->num_lanes > MAX_NUM_LANES) {
> > +             dev_err(dev, "Invalid lane configuration\n");
> > +             return -EINVAL;
> > +     }
> > +
> > +     ret = hdptx_dp_ref_clk(cdns_phy);
> > +     if (ret) {
> > +             dev_err(dev, "Init clk fail\n");
> > +             return -EINVAL;
> > +     }
> > +
> > +     phy_provider = devm_of_phy_provider_register(dev,
> of_phy_simple_xlate);
> > +     if (IS_ERR(phy_provider)) {
> > +             ret =  PTR_ERR(phy_provider);
> > +             goto clk_disable;
> > +     }
> > +
> > +     dev_dbg(dev, "link: (%d lanes)", cdns_phy->num_lanes);
> > +
> > +     return 0;
> > +
> > +clk_disable:
> > +     clk_disable_unprepare(cdns_phy->ref_clk);
> > +
> > +     return -EINVAL;
> > +}
> > +
> > +static int cdns_hdptx_dp_phy_remove(struct platform_device *pdev) {
> > +     struct cdns_hdptx_dp_phy *cdns_phy =
> platform_get_drvdata(pdev);
> > +
> > +     clk_disable_unprepare(cdns_phy->ref_clk);
> > +
> > +     return 0;
> > +}
> > +
> > +static const struct of_device_id cdns_hdptx_dp_phy_of_match[] = {
> > +     {
> > +             .compatible = "cdns,hdptx-dp-phy",
> > +     },
> > +     {}
> > +};
> > +MODULE_DEVICE_TABLE(of, cdns_hdptx_dp_phy_of_match);
> > +
> > +static struct platform_driver cdns_hdptx_dp_phy_driver = {
> > +     .probe  = cdns_hdptx_dp_phy_probe,
> > +     .remove = cdns_hdptx_dp_phy_remove,
> > +     .driver = {
> > +             .name   = "cdns-hdptx-dp-phy",
> > +             .of_match_table = cdns_hdptx_dp_phy_of_match,
> > +     }
> > +};
> > +module_platform_driver(cdns_hdptx_dp_phy_driver);
> > +
> > +MODULE_AUTHOR("Sandor Yu <sandor.yu@nxp.com>");
> > +MODULE_DESCRIPTION("Cadence HDP-TX DisplayPort PHY driver");
> > +MODULE_LICENSE("GPL");
> > --
> > 2.34.1
> 
> --
> ~Vinod

B.R
Sandor
  

Patch

diff --git a/drivers/phy/cadence/Kconfig b/drivers/phy/cadence/Kconfig
index 1adde2d99ae7..1e1914d3afdc 100644
--- a/drivers/phy/cadence/Kconfig
+++ b/drivers/phy/cadence/Kconfig
@@ -46,3 +46,11 @@  config PHY_CADENCE_SALVO
 	  Enable this to support the Cadence SALVO PHY driver,
 	  this PHY is a legacy PHY, and only are used for USB3
 	  and USB2.
+
+config PHY_CADENCE_HDPTX_DP
+	tristate "Cadence HDPTX DP PHY Driver"
+	depends on OF && HAS_IOMEM
+	depends on COMMON_CLK
+	select GENERIC_PHY
+	help
+	  Enable this to support the Cadence HDPTX DP PHY driver
diff --git a/drivers/phy/cadence/Makefile b/drivers/phy/cadence/Makefile
index e17f035ddece..fbdb0bc5ff11 100644
--- a/drivers/phy/cadence/Makefile
+++ b/drivers/phy/cadence/Makefile
@@ -4,3 +4,4 @@  obj-$(CONFIG_PHY_CADENCE_DPHY)	+= cdns-dphy.o
 obj-$(CONFIG_PHY_CADENCE_DPHY_RX)	+= cdns-dphy-rx.o
 obj-$(CONFIG_PHY_CADENCE_SIERRA)	+= phy-cadence-sierra.o
 obj-$(CONFIG_PHY_CADENCE_SALVO)	+= phy-cadence-salvo.o
+obj-$(CONFIG_PHY_CADENCE_HDPTX_DP)	+= phy-cadence-hdptx-dp.o
diff --git a/drivers/phy/cadence/phy-cadence-hdptx-dp.c b/drivers/phy/cadence/phy-cadence-hdptx-dp.c
new file mode 100644
index 000000000000..079d43772d1d
--- /dev/null
+++ b/drivers/phy/cadence/phy-cadence-hdptx-dp.c
@@ -0,0 +1,774 @@ 
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Cadence HDP-TX Display Port Interface (DP) PHY driver
+ *
+ * Copyright (C) 2022 NXP Semiconductor, Inc.
+ */
+#include <asm/unaligned.h>
+#include <linux/clk.h>
+#include <linux/kernel.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+
+#include <drm/bridge/cdns-mhdp-mailbox.h>
+
+#define ADDR_PHY_AFE	0x80000
+
+/* PHY registers */
+#define CMN_SSM_BIAS_TMR                0x0022
+#define CMN_PLLSM0_PLLEN_TMR            0x0029
+#define CMN_PLLSM0_PLLPRE_TMR           0x002A
+#define CMN_PLLSM0_PLLVREF_TMR          0x002B
+#define CMN_PLLSM0_PLLLOCK_TMR          0x002C
+#define CMN_PLLSM0_USER_DEF_CTRL        0x002F
+#define CMN_PSM_CLK_CTRL                0x0061
+#define CMN_CDIAG_REFCLK_CTRL           0x0062
+#define CMN_PLL0_VCOCAL_START           0x0081
+#define CMN_PLL0_VCOCAL_INIT_TMR        0x0084
+#define CMN_PLL0_VCOCAL_ITER_TMR        0x0085
+#define CMN_PLL0_INTDIV                 0x0094
+#define CMN_PLL0_FRACDIV                0x0095
+#define CMN_PLL0_HIGH_THR               0x0096
+#define CMN_PLL0_DSM_DIAG               0x0097
+#define CMN_PLL0_SS_CTRL1               0x0098
+#define CMN_PLL0_SS_CTRL2               0x0099
+#define CMN_ICAL_INIT_TMR               0x00C4
+#define CMN_ICAL_ITER_TMR               0x00C5
+#define CMN_RXCAL_INIT_TMR              0x00D4
+#define CMN_RXCAL_ITER_TMR              0x00D5
+#define CMN_TXPUCAL_CTRL                0x00E0
+#define CMN_TXPUCAL_INIT_TMR            0x00E4
+#define CMN_TXPUCAL_ITER_TMR            0x00E5
+#define CMN_TXPDCAL_CTRL                0x00F0
+#define CMN_TXPDCAL_INIT_TMR            0x00F4
+#define CMN_TXPDCAL_ITER_TMR            0x00F5
+#define CMN_ICAL_ADJ_INIT_TMR           0x0102
+#define CMN_ICAL_ADJ_ITER_TMR           0x0103
+#define CMN_RX_ADJ_INIT_TMR             0x0106
+#define CMN_RX_ADJ_ITER_TMR             0x0107
+#define CMN_TXPU_ADJ_CTRL               0x0108
+#define CMN_TXPU_ADJ_INIT_TMR           0x010A
+#define CMN_TXPU_ADJ_ITER_TMR           0x010B
+#define CMN_TXPD_ADJ_CTRL               0x010c
+#define CMN_TXPD_ADJ_INIT_TMR           0x010E
+#define CMN_TXPD_ADJ_ITER_TMR           0x010F
+#define CMN_DIAG_PLL0_FBH_OVRD          0x01C0
+#define CMN_DIAG_PLL0_FBL_OVRD          0x01C1
+#define CMN_DIAG_PLL0_OVRD              0x01C2
+#define CMN_DIAG_PLL0_TEST_MODE         0x01C4
+#define CMN_DIAG_PLL0_V2I_TUNE          0x01C5
+#define CMN_DIAG_PLL0_CP_TUNE           0x01C6
+#define CMN_DIAG_PLL0_LF_PROG           0x01C7
+#define CMN_DIAG_PLL0_PTATIS_TUNE1      0x01C8
+#define CMN_DIAG_PLL0_PTATIS_TUNE2      0x01C9
+#define CMN_DIAG_PLL0_INCLK_CTRL        0x01CA
+#define CMN_DIAG_PLL0_PXL_DIVH          0x01CB
+#define CMN_DIAG_PLL0_PXL_DIVL          0x01CC
+#define CMN_DIAG_HSCLK_SEL              0x01E0
+#define CMN_DIAG_PER_CAL_ADJ            0x01EC
+#define CMN_DIAG_CAL_CTRL               0x01ED
+#define CMN_DIAG_ACYA                   0x01FF
+#define XCVR_PSM_RCTRL                  0x4001
+#define XCVR_PSM_CAL_TMR                0x4002
+#define XCVR_PSM_A0IN_TMR               0x4003
+#define TX_TXCC_CAL_SCLR_MULT_0         0x4047
+#define TX_TXCC_CPOST_MULT_00_0         0x404C
+#define TX_TXCC_MGNFS_MULT_000_0        0x4050
+#define XCVR_DIAG_PLLDRC_CTRL           0x40E0
+#define XCVR_DIAG_PLLDRC_CTRL           0x40E0
+#define XCVR_DIAG_HSCLK_SEL             0x40E1
+#define XCVR_DIAG_BIDI_CTRL             0x40E8
+#define XCVR_DIAG_LANE_FCM_EN_MGN_TMR   0x40F2
+#define XCVR_DIAG_LANE_FCM_EN_MGN       0x40F2
+#define TX_PSC_A0                       0x4100
+#define TX_PSC_A1                       0x4101
+#define TX_PSC_A2                       0x4102
+#define TX_PSC_A3                       0x4103
+#define TX_RCVDET_CTRL                  0x4120
+#define TX_RCVDET_EN_TMR                0x4122
+#define TX_RCVDET_EN_TMR                0x4122
+#define TX_RCVDET_ST_TMR                0x4123
+#define TX_RCVDET_ST_TMR                0x4123
+#define TX_BIST_CTRL                    0x4140
+#define TX_BIST_UDDWR                   0x4141
+#define TX_DIAG_TX_CTRL                 0x41E0
+#define TX_DIAG_TX_DRV                  0x41E1
+#define TX_DIAG_BGREF_PREDRV_DELAY      0x41E7
+#define TX_DIAG_BGREF_PREDRV_DELAY      0x41E7
+#define XCVR_PSM_RCTRL_1                0x4201
+#define TX_TXCC_CAL_SCLR_MULT_1         0x4247
+#define TX_TXCC_CPOST_MULT_00_1         0x424C
+#define TX_TXCC_MGNFS_MULT_000_1        0x4250
+#define XCVR_DIAG_PLLDRC_CTRL_1         0x42E0
+#define XCVR_DIAG_HSCLK_SEL_1           0x42E1
+#define XCVR_DIAG_LANE_FCM_EN_MGN_TMR_1 0x42F2
+#define TX_RCVDET_EN_TMR_1              0x4322
+#define TX_RCVDET_ST_TMR_1              0x4323
+#define TX_DIAG_ACYA_0                  0x41FF
+#define TX_DIAG_ACYA_1                  0x43FF
+#define TX_DIAG_ACYA_2                  0x45FF
+#define TX_DIAG_ACYA_3                  0x47FF
+#define TX_ANA_CTRL_REG_1               0x5020
+#define TX_ANA_CTRL_REG_2               0x5021
+#define TXDA_COEFF_CALC                 0x5022
+#define TX_DIG_CTRL_REG_1               0x5023
+#define TX_DIG_CTRL_REG_2               0x5024
+#define TXDA_CYA_AUXDA_CYA              0x5025
+#define TX_ANA_CTRL_REG_3               0x5026
+#define TX_ANA_CTRL_REG_4               0x5027
+#define TX_ANA_CTRL_REG_5               0x5029
+#define RX_PSC_A0                       0x8000
+#define RX_PSC_CAL                      0x8006
+#define PMA_LANE_CFG                    0xC000
+#define PIPE_CMN_CTRL1                  0xC001
+#define PIPE_CMN_CTRL2                  0xC002
+#define PIPE_COM_LOCK_CFG1              0xC003
+#define PIPE_COM_LOCK_CFG2              0xC004
+#define PIPE_RCV_DET_INH                0xC005
+#define PHY_HDP_MODE_CTRL               0xC008
+#define PHY_HDP_CLK_CTL                 0xC009
+#define STS                             0xC00F
+#define PHY_ISO_CMN_CTRL                0xC010
+#define PHY_ISO_CMN_CTRL                0xC010
+#define PHY_HDP_TX_CTL_L0               0xC408
+#define PHY_DP_TX_CTL                   0xC408
+#define PHY_HDP_TX_CTL_L1               0xC448
+#define PHY_HDP_TX_CTL_L2               0xC488
+#define PHY_HDP_TX_CTL_L3               0xC4C8
+#define PHY_PMA_CMN_CTRL1               0xC800
+#define PMA_CMN_CTRL1                   0xC800
+#define PHY_PMA_ISO_CMN_CTRL            0xC810
+#define PHY_PMA_ISO_PLL_CTRL1           0xC812
+#define PHY_PMA_ISOLATION_CTRL          0xC81F
+#define PHY_ISOLATION_CTRL              0xC81F
+#define PHY_PMA_ISO_XCVR_CTRL           0xCC11
+#define PHY_PMA_ISO_LINK_MODE           0xCC12
+#define PHY_PMA_ISO_PWRST_CTRL          0xCC13
+#define PHY_PMA_ISO_TX_DATA_LO          0xCC14
+#define PHY_PMA_ISO_TX_DATA_HI          0xCC15
+#define PHY_PMA_ISO_RX_DATA_LO          0xCC16
+#define PHY_PMA_ISO_RX_DATA_HI          0xCC17
+
+#define MAX_NUM_LANES		4
+#define DEFAULT_MAX_BIT_RATE	5400 /* in Mbps */
+
+#define REF_CLK_27MHZ		27000000
+
+enum dp_link_rate {
+	RATE_1_6 = 162000,
+	RATE_2_1 = 216000,
+	RATE_2_4 = 243000,
+	RATE_2_7 = 270000,
+	RATE_3_2 = 324000,
+	RATE_4_3 = 432000,
+	RATE_5_4 = 540000,
+	RATE_8_1 = 810000,
+};
+
+struct phy_pll_reg {
+	u16 val[7];
+	u32 addr;
+};
+
+static const struct phy_pll_reg phy_pll_27m_cfg[] = {
+	/*  1.62    2.16    2.43    2.7     3.24    4.32    5.4      register address */
+	{{ 0x010E, 0x010E, 0x010E, 0x010E, 0x010E, 0x010E, 0x010E }, CMN_PLL0_VCOCAL_INIT_TMR },
+	{{ 0x001B, 0x001B, 0x001B, 0x001B, 0x001B, 0x001B, 0x001B }, CMN_PLL0_VCOCAL_ITER_TMR },
+	{{ 0x30B9, 0x3087, 0x3096, 0x30B4, 0x30B9, 0x3087, 0x30B4 }, CMN_PLL0_VCOCAL_START },
+	{{ 0x0077, 0x009F, 0x00B3, 0x00C7, 0x0077, 0x009F, 0x00C7 }, CMN_PLL0_INTDIV },
+	{{ 0xF9DA, 0xF7CD, 0xF6C7, 0xF5C1, 0xF9DA, 0xF7CD, 0xF5C1 }, CMN_PLL0_FRACDIV },
+	{{ 0x001E, 0x0028, 0x002D, 0x0032, 0x001E, 0x0028, 0x0032 }, CMN_PLL0_HIGH_THR },
+	{{ 0x0020, 0x0020, 0x0020, 0x0020, 0x0020, 0x0020, 0x0020 }, CMN_PLL0_DSM_DIAG },
+	{{ 0x0000, 0x1000, 0x1000, 0x1000, 0x0000, 0x1000, 0x1000 }, CMN_PLLSM0_USER_DEF_CTRL },
+	{{ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000 }, CMN_DIAG_PLL0_OVRD },
+	{{ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000 }, CMN_DIAG_PLL0_FBH_OVRD },
+	{{ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000 }, CMN_DIAG_PLL0_FBL_OVRD },
+	{{ 0x0006, 0x0007, 0x0007, 0x0007, 0x0006, 0x0007, 0x0007 }, CMN_DIAG_PLL0_V2I_TUNE },
+	{{ 0x0043, 0x0043, 0x0043, 0x0042, 0x0043, 0x0043, 0x0042 }, CMN_DIAG_PLL0_CP_TUNE },
+	{{ 0x0008, 0x0008, 0x0008, 0x0008, 0x0008, 0x0008, 0x0008 }, CMN_DIAG_PLL0_LF_PROG },
+	{{ 0x0100, 0x0001, 0x0001, 0x0001, 0x0100, 0x0001, 0x0001 }, CMN_DIAG_PLL0_PTATIS_TUNE1 },
+	{{ 0x0007, 0x0001, 0x0001, 0x0001, 0x0007, 0x0001, 0x0001 }, CMN_DIAG_PLL0_PTATIS_TUNE2 },
+	{{ 0x0020, 0x0020, 0x0020, 0x0020, 0x0020, 0x0020, 0x0020 }, CMN_DIAG_PLL0_TEST_MODE},
+	{{ 0x0016, 0x0016, 0x0016, 0x0016, 0x0016, 0x0016, 0x0016 }, CMN_PSM_CLK_CTRL }
+};
+
+struct cdns_hdptx_dp_phy {
+	void __iomem *regs;	/* DPTX registers base */
+	struct device *dev;
+	struct phy *phy;
+	struct mutex mbox_mutex; /* mutex to protect mailbox */
+	struct clk *ref_clk;
+	u32 ref_clk_rate;
+	u32 num_lanes;
+	u32 max_bit_rate; /* Maximum link bit rate to use (in Mbps) */
+	u32 link_rate;
+	bool power_up;
+};
+
+static int cdns_phy_reg_write(struct cdns_hdptx_dp_phy *cdns_phy, u32 addr, u32 val)
+{
+	return cdns_mhdp_reg_write(cdns_phy, ADDR_PHY_AFE + (addr << 2), val);
+}
+
+static u32 cdns_phy_reg_read(struct cdns_hdptx_dp_phy *cdns_phy, u32 addr)
+{
+	u32 reg32;
+
+	cdns_mhdp_reg_read(cdns_phy, ADDR_PHY_AFE + (addr << 2), &reg32);
+	return reg32;
+}
+
+static int link_rate_index(u32 rate)
+{
+	switch (rate) {
+	case RATE_1_6:
+		return 0;
+	case RATE_2_1:
+		return 1;
+	case RATE_2_4:
+		return 2;
+	case RATE_2_7:
+		return 3;
+	case RATE_3_2:
+		return 4;
+	case RATE_4_3:
+		return 5;
+	case RATE_5_4:
+		return 6;
+	default:
+		return -1;
+	}
+}
+
+static int hdptx_dp_ref_clk(struct cdns_hdptx_dp_phy *cdns_phy)
+{
+	struct device *dev = cdns_phy->dev;
+	u32 ref_clk_rate;
+	int ret;
+
+	cdns_phy->ref_clk = devm_clk_get(dev, "refclk");
+	if (IS_ERR(cdns_phy->ref_clk)) {
+		dev_err(dev, "phy ref clock not found\n");
+		return PTR_ERR(cdns_phy->ref_clk);
+	}
+
+	ret = clk_prepare_enable(cdns_phy->ref_clk);
+	if (ret) {
+		dev_err(cdns_phy->dev, "Failed to prepare ref clock\n");
+		return ret;
+	}
+
+	ref_clk_rate = clk_get_rate(cdns_phy->ref_clk);
+	if (!ref_clk_rate) {
+		dev_err(cdns_phy->dev, "Failed to get ref clock rate\n");
+		goto err_ref_clk;
+	}
+
+	if (ref_clk_rate == REF_CLK_27MHZ)
+		cdns_phy->ref_clk_rate = ref_clk_rate;
+	else {
+		dev_err(cdns_phy->dev, "Not support Ref Clock Rate(%dHz)\n", ref_clk_rate);
+		goto err_ref_clk;
+	}
+
+	return 0;
+
+err_ref_clk:
+	clk_disable_unprepare(cdns_phy->ref_clk);
+	return -EINVAL;
+}
+
+static void hdptx_dp_aux_cfg(struct cdns_hdptx_dp_phy *cdns_phy)
+{
+	/* Power up Aux */
+	cdns_phy_reg_write(cdns_phy, TXDA_CYA_AUXDA_CYA, 1);
+
+	cdns_phy_reg_write(cdns_phy, TX_DIG_CTRL_REG_1, 0x3);
+	ndelay(150);
+	cdns_phy_reg_write(cdns_phy, TX_DIG_CTRL_REG_2, 36);
+	ndelay(150);
+	cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_2, 0x0100);
+	ndelay(150);
+	cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_2, 0x0300);
+	ndelay(150);
+	cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_3, 0x0000);
+	ndelay(150);
+	cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_1, 0x2008);
+	ndelay(150);
+	cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_1, 0x2018);
+	ndelay(150);
+	cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_1, 0xA018);
+	ndelay(150);
+	cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_2, 0x030C);
+	ndelay(150);
+	cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_5, 0x0000);
+	ndelay(150);
+	cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_4, 0x1001);
+	ndelay(150);
+	cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_1, 0xA098);
+	ndelay(150);
+	cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_1, 0xA198);
+	ndelay(150);
+	cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_2, 0x030d);
+	ndelay(150);
+	cdns_phy_reg_write(cdns_phy, TX_ANA_CTRL_REG_2, 0x030f);
+}
+
+/* PMA common configuration for 27MHz */
+static void hdptx_dp_phy_pma_cmn_cfg_27mhz(struct cdns_hdptx_dp_phy *cdns_phy)
+{
+	u32 num_lanes = cdns_phy->num_lanes;
+	u16 val;
+	int k;
+
+	val = cdns_phy_reg_read(cdns_phy, PHY_PMA_CMN_CTRL1);
+	val &= 0xFFF7;
+	val |= 0x0008;
+	cdns_phy_reg_write(cdns_phy, PHY_PMA_CMN_CTRL1, val);
+
+	/* Startup state machine registers */
+	cdns_phy_reg_write(cdns_phy, CMN_SSM_BIAS_TMR, 0x0087);
+	cdns_phy_reg_write(cdns_phy, CMN_PLLSM0_PLLEN_TMR, 0x001B);
+	cdns_phy_reg_write(cdns_phy, CMN_PLLSM0_PLLPRE_TMR, 0x0036);
+	cdns_phy_reg_write(cdns_phy, CMN_PLLSM0_PLLVREF_TMR, 0x001B);
+	cdns_phy_reg_write(cdns_phy, CMN_PLLSM0_PLLLOCK_TMR, 0x006C);
+
+	/* Current calibration registers */
+	cdns_phy_reg_write(cdns_phy, CMN_ICAL_INIT_TMR, 0x0044);
+	cdns_phy_reg_write(cdns_phy, CMN_ICAL_ITER_TMR, 0x0006);
+	cdns_phy_reg_write(cdns_phy, CMN_ICAL_ADJ_INIT_TMR, 0x0022);
+	cdns_phy_reg_write(cdns_phy, CMN_ICAL_ADJ_ITER_TMR, 0x0006);
+
+	/* Resistor calibration registers */
+	cdns_phy_reg_write(cdns_phy, CMN_TXPUCAL_INIT_TMR, 0x0022);
+	cdns_phy_reg_write(cdns_phy, CMN_TXPUCAL_ITER_TMR, 0x0006);
+	cdns_phy_reg_write(cdns_phy, CMN_TXPU_ADJ_INIT_TMR, 0x0022);
+	cdns_phy_reg_write(cdns_phy, CMN_TXPU_ADJ_ITER_TMR, 0x0006);
+	cdns_phy_reg_write(cdns_phy, CMN_TXPDCAL_INIT_TMR, 0x0022);
+	cdns_phy_reg_write(cdns_phy, CMN_TXPDCAL_ITER_TMR, 0x0006);
+	cdns_phy_reg_write(cdns_phy, CMN_TXPD_ADJ_INIT_TMR, 0x0022);
+	cdns_phy_reg_write(cdns_phy, CMN_TXPD_ADJ_ITER_TMR, 0x0006);
+	cdns_phy_reg_write(cdns_phy, CMN_RXCAL_INIT_TMR, 0x0022);
+	cdns_phy_reg_write(cdns_phy, CMN_RXCAL_ITER_TMR, 0x0006);
+	cdns_phy_reg_write(cdns_phy, CMN_RX_ADJ_INIT_TMR, 0x0022);
+	cdns_phy_reg_write(cdns_phy, CMN_RX_ADJ_ITER_TMR, 0x0006);
+
+	for (k = 0; k < num_lanes; k = k + 1) {
+		/* Power state machine registers */
+		cdns_phy_reg_write(cdns_phy, XCVR_PSM_CAL_TMR  | (k << 9), 0x016D);
+		cdns_phy_reg_write(cdns_phy, XCVR_PSM_A0IN_TMR | (k << 9), 0x016D);
+		/* Transceiver control and diagnostic registers */
+		cdns_phy_reg_write(cdns_phy, XCVR_DIAG_LANE_FCM_EN_MGN_TMR | (k << 9), 0x00A2);
+		cdns_phy_reg_write(cdns_phy, TX_DIAG_BGREF_PREDRV_DELAY    | (k << 9), 0x0097);
+		/* Transmitter receiver detect registers */
+		cdns_phy_reg_write(cdns_phy, TX_RCVDET_EN_TMR | (k << 9), 0x0A8C);
+		cdns_phy_reg_write(cdns_phy, TX_RCVDET_ST_TMR | (k << 9), 0x0036);
+	}
+
+	cdns_phy_reg_write(cdns_phy, TX_DIAG_ACYA_0, 1);
+	cdns_phy_reg_write(cdns_phy, TX_DIAG_ACYA_1, 1);
+	cdns_phy_reg_write(cdns_phy, TX_DIAG_ACYA_2, 1);
+	cdns_phy_reg_write(cdns_phy, TX_DIAG_ACYA_3, 1);
+}
+
+static void hdptx_dp_phy_pma_cmn_pll0_27mhz(struct cdns_hdptx_dp_phy *cdns_phy)
+{
+	u32 num_lanes = cdns_phy->num_lanes;
+	u32 link_rate = cdns_phy->link_rate;
+	u16 val;
+	int index, i, k;
+
+	/* DP PLL data rate 0/1 clock divider value */
+	val = cdns_phy_reg_read(cdns_phy, PHY_HDP_CLK_CTL);
+	val &= 0x00FF;
+	if (link_rate <= RATE_2_7)
+		val |= 0x2400;
+	else
+		val |= 0x1200;
+	cdns_phy_reg_write(cdns_phy, PHY_HDP_CLK_CTL, val);
+
+	/* High speed clock 0/1 div */
+	val = cdns_phy_reg_read(cdns_phy, CMN_DIAG_HSCLK_SEL);
+	val &= 0xFFCC;
+	if (link_rate <= RATE_2_7)
+		val |= 0x0011;
+	cdns_phy_reg_write(cdns_phy, CMN_DIAG_HSCLK_SEL, val);
+
+	for (k = 0; k < num_lanes; k++) {
+		val = cdns_phy_reg_read(cdns_phy, (XCVR_DIAG_HSCLK_SEL | (k << 9)));
+		val = val & 0xCFFF;
+		if (link_rate <= RATE_2_7)
+			val |= 0x1000;
+		cdns_phy_reg_write(cdns_phy, (XCVR_DIAG_HSCLK_SEL | (k << 9)), val);
+	}
+
+	/* DP PHY PLL 27MHz configuration */
+	index = link_rate_index(link_rate);
+	for (i = 0; i < ARRAY_SIZE(phy_pll_27m_cfg); i++)
+		cdns_phy_reg_write(cdns_phy, phy_pll_27m_cfg[i].addr,
+				phy_pll_27m_cfg[i].val[index]);
+
+	/* Transceiver control and diagnostic registers */
+	for (k = 0; k < num_lanes; k++) {
+		val = cdns_phy_reg_read(cdns_phy, (XCVR_DIAG_PLLDRC_CTRL | (k << 9)));
+		val = val & 0x8FFF;
+		if (link_rate <= RATE_2_7)
+			val |= 0x2000;
+		else
+			val |= 0x1000;
+		cdns_phy_reg_write(cdns_phy, (XCVR_DIAG_PLLDRC_CTRL | (k << 9)), val);
+	}
+
+	for (k = 0; k < num_lanes; k = k + 1) {
+		/* Power state machine registers */
+		cdns_phy_reg_write(cdns_phy, (XCVR_PSM_RCTRL | (k << 9)),  0xBEFC);
+		cdns_phy_reg_write(cdns_phy, (TX_PSC_A0 | (k << 9)), 0x6799);
+		cdns_phy_reg_write(cdns_phy, (TX_PSC_A1 | (k << 9)), 0x6798);
+		cdns_phy_reg_write(cdns_phy, (TX_PSC_A2 | (k << 9)), 0x0098);
+		cdns_phy_reg_write(cdns_phy, (TX_PSC_A3 | (k << 9)), 0x0098);
+		/* Receiver calibration power state definition register */
+		val = cdns_phy_reg_read(cdns_phy, RX_PSC_CAL | (k << 9));
+		val &= 0xFFBB;
+		cdns_phy_reg_write(cdns_phy, (RX_PSC_CAL | (k << 9)), val);
+		val = cdns_phy_reg_read(cdns_phy, RX_PSC_A0  | (k << 9));
+		val &= 0xFFBB;
+		cdns_phy_reg_write(cdns_phy, (RX_PSC_A0  | (k << 9)), val);
+	}
+}
+
+static void hdptx_dp_phy_ref_clock_type(struct cdns_hdptx_dp_phy *cdns_phy)
+{
+	u32 val;
+
+	val = cdns_phy_reg_read(cdns_phy, PHY_PMA_CMN_CTRL1);
+	val &= 0xFF8F;
+	/*
+	 * single ended reference clock (val |= 0x0030);
+	 * differential clock  (val |= 0x0000);
+	 *
+	 * for differential clock on the refclk_p and
+	 * refclk_m off chip pins: CMN_DIAG_ACYA[8]=1'b1
+	 * cdns_phy_reg_write(cdns_phy, CMN_DIAG_ACYA, 0x0100);
+	 */
+	val |= 0x0030;
+	cdns_phy_reg_write(cdns_phy, PHY_PMA_CMN_CTRL1, val);
+}
+
+static int hdptx_dp_phy_power_up(struct cdns_hdptx_dp_phy *cdns_phy)
+{
+	u32 val, i;
+
+	/* Enable HDP PLL’s for high speed clocks */
+	val = cdns_phy_reg_read(cdns_phy, PHY_HDP_CLK_CTL);
+	val |= (1 << 0);
+	cdns_phy_reg_write(cdns_phy, PHY_HDP_CLK_CTL, val);
+	/* Wait for PLL ready ACK */
+	for (i = 0; i < 10; i++) {
+		val = cdns_phy_reg_read(cdns_phy, PHY_HDP_CLK_CTL);
+		if (val & (1 << 1))
+			break;
+		msleep(20);
+	}
+	if (i == 10) {
+		dev_err(cdns_phy->dev, "Wait PLL Ack failed\n");
+		return -1;
+	}
+
+	/* Enable HDP PLL’s data rate and full rate clocks out of PMA. */
+	val = cdns_phy_reg_read(cdns_phy, PHY_HDP_CLK_CTL);
+	val |= (1 << 2);
+	cdns_phy_reg_write(cdns_phy, PHY_HDP_CLK_CTL, val);
+	/* Wait for PLL clock enable ACK */
+	for (i = 0; i < 10; i++) {
+		val = cdns_phy_reg_read(cdns_phy, PHY_HDP_CLK_CTL);
+		if (val & (1 << 3))
+			break;
+		msleep(20);
+	}
+	if (i == 10) {
+		dev_err(cdns_phy->dev, "Wait PLL clock enable ACk failed\n");
+		return -1;
+	}
+
+	/* Configure PHY in A2 Mode */
+	cdns_phy_reg_write(cdns_phy, PHY_HDP_MODE_CTRL, 0x0004);
+	/* Wait for Power State A2 Ack */
+	for (i = 0; i < 10; i++) {
+		val = cdns_phy_reg_read(cdns_phy, PHY_HDP_MODE_CTRL);
+		if (val & (1 << 6))
+			break;
+		msleep(20);
+	}
+	if (i == 10) {
+		dev_err(cdns_phy->dev, "Wait A2 Ack failed\n");
+		return -1;
+	}
+
+	/* Configure PHY in A0 mode (PHY must be in the A0 power
+	 * state in order to transmit data)
+	 */
+	cdns_phy_reg_write(cdns_phy, PHY_HDP_MODE_CTRL, 0x0101);
+
+	/* Wait for Power State A0 Ack */
+	for (i = 0; i < 10; i++) {
+		val = cdns_phy_reg_read(cdns_phy, PHY_HDP_MODE_CTRL);
+		if (val & (1 << 4))
+			break;
+		msleep(20);
+	}
+	if (i == 10) {
+		dev_err(cdns_phy->dev, "Wait A0 Ack failed\n");
+		return -1;
+	}
+
+	cdns_phy->power_up = true;
+
+	return 0;
+}
+
+static void hdptx_dp_phy_power_down(struct cdns_hdptx_dp_phy *cdns_phy)
+{
+	u16 val;
+	int i;
+
+	if (!cdns_phy->power_up)
+		return;
+
+	/* Place the PHY lanes in the A3 power state. */
+	cdns_phy_reg_write(cdns_phy, PHY_HDP_MODE_CTRL, 0x8);
+	/* Wait for Power State A3 Ack */
+	for (i = 0; i < 10; i++) {
+		val = cdns_phy_reg_read(cdns_phy, PHY_HDP_MODE_CTRL);
+		if (val & (1 << 7))
+			break;
+		msleep(20);
+	}
+	if (i == 10) {
+		dev_err(cdns_phy->dev, "Wait A3 Ack failed\n");
+		return;
+	}
+
+	/* Disable HDP PLL’s data rate and full rate clocks out of PMA. */
+	val = cdns_phy_reg_read(cdns_phy, PHY_HDP_CLK_CTL);
+	val &= ~(1 << 2);
+	cdns_phy_reg_write(cdns_phy, PHY_HDP_CLK_CTL, val);
+	/* Wait for PLL clock gate ACK */
+	for (i = 0; i < 10; i++) {
+		val = cdns_phy_reg_read(cdns_phy, PHY_HDP_CLK_CTL);
+		if (!(val & (1 << 3)))
+			break;
+		msleep(20);
+	}
+	if (i == 10) {
+		dev_err(cdns_phy->dev, "Wait PLL clock gate Ack failed\n");
+		return;
+	}
+
+	/* Disable HDP PLL’s for high speed clocks */
+	val = cdns_phy_reg_read(cdns_phy, PHY_HDP_CLK_CTL);
+	val &= ~(1 << 0);
+	cdns_phy_reg_write(cdns_phy, PHY_HDP_CLK_CTL, val);
+	/* Wait for PLL disable ACK */
+	for (i = 0; i < 10; i++) {
+		val = cdns_phy_reg_read(cdns_phy, PHY_HDP_CLK_CTL);
+		if (!(val & (1 << 1)))
+			break;
+		msleep(20);
+	}
+	if (i == 10) {
+		dev_err(cdns_phy->dev, "Wait PLL disable Ack failed\n");
+		return;
+	}
+}
+
+static int cdns_hdptx_dp_phy_on(struct phy *phy)
+{
+	struct cdns_hdptx_dp_phy *cdns_phy = phy_get_drvdata(phy);
+
+	return hdptx_dp_phy_power_up(cdns_phy);
+}
+
+static int cdns_hdptx_dp_phy_off(struct phy *phy)
+{
+	struct cdns_hdptx_dp_phy *cdns_phy = phy_get_drvdata(phy);
+
+	hdptx_dp_phy_power_down(cdns_phy);
+
+	return 0;
+}
+
+static int cdns_hdptx_dp_phy_init(struct phy *phy)
+{
+	struct cdns_hdptx_dp_phy *cdns_phy = phy_get_drvdata(phy);
+	int ret;
+
+	hdptx_dp_phy_ref_clock_type(cdns_phy);
+
+	/* PHY power up */
+	ret = hdptx_dp_phy_power_up(cdns_phy);
+	if (ret < 0)
+		return ret;
+
+	hdptx_dp_aux_cfg(cdns_phy);
+
+	return ret;
+}
+
+static int cdns_hdptx_dp_configure(struct phy *phy,
+				     union phy_configure_opts *opts)
+{
+	struct cdns_hdptx_dp_phy *cdns_phy = phy_get_drvdata(phy);
+	int ret;
+
+	cdns_phy->link_rate = opts->dp.link_rate;
+
+	/* Disable phy clock if PHY in power up state */
+	hdptx_dp_phy_power_down(cdns_phy);
+
+	if (cdns_phy->ref_clk_rate == REF_CLK_27MHZ) {
+		hdptx_dp_phy_pma_cmn_cfg_27mhz(cdns_phy);
+		hdptx_dp_phy_pma_cmn_pll0_27mhz(cdns_phy);
+	} else
+		dev_err(cdns_phy->dev, "Not support ref clock rate\n");
+
+	/* PHY power up */
+	ret = hdptx_dp_phy_power_up(cdns_phy);
+
+	return ret;
+}
+
+static const struct phy_ops cdns_hdptx_dp_phy_ops = {
+	.init		= cdns_hdptx_dp_phy_init,
+	.configure	= cdns_hdptx_dp_configure,
+	.power_on	= cdns_hdptx_dp_phy_on,
+	.power_off	= cdns_hdptx_dp_phy_off,
+	.owner		= THIS_MODULE,
+};
+
+static int cdns_hdptx_dp_phy_probe(struct platform_device *pdev)
+{
+	struct cdns_hdptx_dp_phy *cdns_phy;
+	struct device *dev = &pdev->dev;
+	struct device_node *node = dev->of_node;
+	struct phy_provider *phy_provider;
+	struct resource *res;
+	struct phy *phy;
+	int ret;
+
+	cdns_phy = devm_kzalloc(dev, sizeof(*cdns_phy), GFP_KERNEL);
+	if (!cdns_phy)
+		return -ENOMEM;
+
+	dev_set_drvdata(dev, cdns_phy);
+	cdns_phy->dev = dev;
+	mutex_init(&cdns_phy->mbox_mutex);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res)
+		return -ENODEV;
+	cdns_phy->regs = devm_ioremap(dev, res->start, resource_size(res));
+	if (IS_ERR(cdns_phy->regs))
+		return PTR_ERR(cdns_phy->regs);
+
+	if (of_property_read_u32(node, "cdns,num-lanes",
+				 &cdns_phy->num_lanes)) {
+		dev_err(dev, "%s: No \"cdns,num-lanes\"-property.\n",
+			node->full_name);
+		return -EINVAL;
+	}
+
+	phy = devm_phy_create(dev, node, &cdns_hdptx_dp_phy_ops);
+	if (IS_ERR(phy))
+		return PTR_ERR(phy);
+
+	cdns_phy->max_bit_rate = DEFAULT_MAX_BIT_RATE;
+	of_property_read_u32(node, "cdns,max-bit-rate",
+			     &cdns_phy->max_bit_rate);
+
+	switch (cdns_phy->max_bit_rate) {
+	/* valid bit rate */
+	case 1620:
+	case 2160:
+	case 2430:
+	case 2700:
+	case 3240:
+	case 4320:
+	case 5400:
+		break;
+	case 8100:
+	default:
+		dev_err(dev, "unsupported max bit rate: %dMbps\n",
+				cdns_phy->max_bit_rate);
+		return -EINVAL;
+	}
+
+	dev_dbg(dev, "DP max bit rate %d.%03d Gbps\n",
+		cdns_phy->max_bit_rate / 1000,
+		cdns_phy->max_bit_rate % 1000);
+
+	phy->attrs.bus_width = cdns_phy->num_lanes;
+	phy->attrs.max_link_rate = cdns_phy->max_bit_rate;
+	phy->attrs.mode = PHY_MODE_DP;
+
+	cdns_phy->phy = phy;
+	phy_set_drvdata(phy, cdns_phy);
+
+	if (cdns_phy->num_lanes > MAX_NUM_LANES) {
+		dev_err(dev, "Invalid lane configuration\n");
+		return -EINVAL;
+	}
+
+	ret = hdptx_dp_ref_clk(cdns_phy);
+	if (ret) {
+		dev_err(dev, "Init clk fail\n");
+		return -EINVAL;
+	}
+
+	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+	if (IS_ERR(phy_provider)) {
+		ret =  PTR_ERR(phy_provider);
+		goto clk_disable;
+	}
+
+	dev_dbg(dev, "link: (%d lanes)", cdns_phy->num_lanes);
+
+	return 0;
+
+clk_disable:
+	clk_disable_unprepare(cdns_phy->ref_clk);
+
+	return -EINVAL;
+}
+
+static int cdns_hdptx_dp_phy_remove(struct platform_device *pdev)
+{
+	struct cdns_hdptx_dp_phy *cdns_phy = platform_get_drvdata(pdev);
+
+	clk_disable_unprepare(cdns_phy->ref_clk);
+
+	return 0;
+}
+
+static const struct of_device_id cdns_hdptx_dp_phy_of_match[] = {
+	{
+		.compatible = "cdns,hdptx-dp-phy",
+	},
+	{}
+};
+MODULE_DEVICE_TABLE(of, cdns_hdptx_dp_phy_of_match);
+
+static struct platform_driver cdns_hdptx_dp_phy_driver = {
+	.probe	= cdns_hdptx_dp_phy_probe,
+	.remove = cdns_hdptx_dp_phy_remove,
+	.driver = {
+		.name	= "cdns-hdptx-dp-phy",
+		.of_match_table	= cdns_hdptx_dp_phy_of_match,
+	}
+};
+module_platform_driver(cdns_hdptx_dp_phy_driver);
+
+MODULE_AUTHOR("Sandor Yu <sandor.yu@nxp.com>");
+MODULE_DESCRIPTION("Cadence HDP-TX DisplayPort PHY driver");
+MODULE_LICENSE("GPL");