[2/2] phy: add driver for MediaTek XFI T-PHY

Message ID dd6b40ea1f7f8459a9a2cfe7fa60c1108332ade6.1706823233.git.daniel@makrotopia.org
State New
Headers
Series [1/2] dt-bindings: phy: mediatek,xfi-tphy: add new bindings |

Commit Message

Daniel Golle Feb. 1, 2024, 9:53 p.m. UTC
  Add driver for MediaTek's XFI T-PHY, 10 Gigabit/s Ethernet SerDes PHY
which can be found in the MT7988 SoC.

The PHY can operates only in PHY_MODE_ETHERNET, the submode is one of
PHY_INTERFACE_MODE_* corresponding to the supported modes:

 * USXGMII                 \
 * 10GBase-R                }- USXGMII PCS - XGDM  \
 * 5GBase-R                /                        \
                                                     }- Ethernet MAC
 * 2500Base-X              \                        /
 * 1000Base-X               }- LynxI PCS - GDM     /
 * Cisco SGMII (MAC side)  /

In order to work-around a performance issue present on the first of
two XFI T-PHYs present in MT7988, special tuning is applied which can be
selected by adding the 'mediatek,usxgmii-performance-errata' property to
the device tree node.

There is no documentation for most registers used for the
analog/tuning part, however, most of the registers have been partially
reverse-engineered from MediaTek's SDK implementation (an opaque
sequence of 32-bit register writes) and descriptions for all relevant
digital registers and bits such as resets and muxes have been supplied
by MediaTek.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
---
 MAINTAINERS                             |   1 +
 drivers/phy/mediatek/Kconfig            |  12 +
 drivers/phy/mediatek/Makefile           |   1 +
 drivers/phy/mediatek/phy-mtk-xfi-tphy.c | 392 ++++++++++++++++++++++++
 4 files changed, 406 insertions(+)
 create mode 100644 drivers/phy/mediatek/phy-mtk-xfi-tphy.c
  

Comments

Chunfeng Yun (云春峰) Feb. 4, 2024, 6:29 a.m. UTC | #1
On Thu, 2024-02-01 at 21:53 +0000, Daniel Golle wrote:
>  	 
> External email : Please do not click links or open attachments until
> you have verified the sender or the content.
>  Add driver for MediaTek's XFI T-PHY, 10 Gigabit/s Ethernet SerDes
> PHY
> which can be found in the MT7988 SoC.
> 
> The PHY can operates only in PHY_MODE_ETHERNET, the submode is one of
> PHY_INTERFACE_MODE_* corresponding to the supported modes:
> 
>  * USXGMII                 \
>  * 10GBase-R                }- USXGMII PCS - XGDM  \
>  * 5GBase-R                /                        \
>                                                      }- Ethernet MAC
>  * 2500Base-X              \                        /
>  * 1000Base-X               }- LynxI PCS - GDM     /
>  * Cisco SGMII (MAC side)  /
> 
> In order to work-around a performance issue present on the first of
> two XFI T-PHYs present in MT7988, special tuning is applied which can
> be
> selected by adding the 'mediatek,usxgmii-performance-errata' property
> to
> the device tree node.
> 
> There is no documentation for most registers used for the
> analog/tuning part, however, most of the registers have been
> partially
> reverse-engineered from MediaTek's SDK implementation (an opaque
> sequence of 32-bit register writes) and descriptions for all relevant
> digital registers and bits such as resets and muxes have been
> supplied
> by MediaTek.
> 
> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
> ---
>  MAINTAINERS                             |   1 +
>  drivers/phy/mediatek/Kconfig            |  12 +
>  drivers/phy/mediatek/Makefile           |   1 +
>  drivers/phy/mediatek/phy-mtk-xfi-tphy.c | 392
> ++++++++++++++++++++++++
>  4 files changed, 406 insertions(+)
>  create mode 100644 drivers/phy/mediatek/phy-mtk-xfi-tphy.c
> 
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 52769631bdb1a..52e4192470bd9 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -13715,6 +13715,7 @@ L:netdev@vger.kernel.org
>  S:Maintained
>  F:drivers/net/phy/mediatek-ge-soc.c
>  F:drivers/net/phy/mediatek-ge.c
> +F:drivers/phy/mediatek/phy-mtk-xfi-tphy.c
>  
>  MEDIATEK I2C CONTROLLER DRIVER
>  M:Qii Wang <qii.wang@mediatek.com>
> diff --git a/drivers/phy/mediatek/Kconfig
> b/drivers/phy/mediatek/Kconfig
> index 3125ecb5d119f..5161d130c7f8b 100644
> --- a/drivers/phy/mediatek/Kconfig
> +++ b/drivers/phy/mediatek/Kconfig
> @@ -13,6 +13,18 @@ config PHY_MTK_PCIE
>    callback for PCIe GEN3 port, it supports software efuse
>    initialization.
>  
> +config PHY_MTK_XFI_TPHY
> +tristate "MediaTek XFI T-PHY Driver"
> +depends on ARCH_MEDIATEK || COMPILE_TEST
> +depends on OF && OF_ADDRESS
> +depends on HAS_IOMEM
> +select GENERIC_PHY
> +help
> +  Say 'Y' here to add support for MediaTek XFI T-PHY driver.
> +  The driver provides access to the Ethernet SerDes T-PHY supporting
> +  1GE and 2.5GE modes via the LynxI PCS, and 5GE and 10GE modes
> +  via the USXGMII PCS found in MediaTek SoCs with 10G Ethernet.
> +
>  config PHY_MTK_TPHY
>  tristate "MediaTek T-PHY Driver"
>  depends on ARCH_MEDIATEK || COMPILE_TEST
> diff --git a/drivers/phy/mediatek/Makefile
> b/drivers/phy/mediatek/Makefile
> index c9a50395533eb..fa7217178e7f4 100644
> --- a/drivers/phy/mediatek/Makefile
> +++ b/drivers/phy/mediatek/Makefile
> @@ -8,6 +8,7 @@ obj-$(CONFIG_PHY_MTK_PCIE)+= phy-mtk-pcie.o
>  obj-$(CONFIG_PHY_MTK_TPHY)+= phy-mtk-tphy.o
>  obj-$(CONFIG_PHY_MTK_UFS)+= phy-mtk-ufs.o
>  obj-$(CONFIG_PHY_MTK_XSPHY)+= phy-mtk-xsphy.o
> +obj-$(CONFIG_PHY_MTK_XFI_TPHY)+= phy-mtk-xfi-tphy.o
>  
>  phy-mtk-hdmi-drv-y:= phy-mtk-hdmi.o
>  phy-mtk-hdmi-drv-y+= phy-mtk-hdmi-mt2701.o
> diff --git a/drivers/phy/mediatek/phy-mtk-xfi-tphy.c
> b/drivers/phy/mediatek/phy-mtk-xfi-tphy.c
> new file mode 100644
> index 0000000000000..d50e6320860e5
> --- /dev/null
> +++ b/drivers/phy/mediatek/phy-mtk-xfi-tphy.c
> @@ -0,0 +1,392 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +/* MediaTek 10GE SerDes PHY driver
> + *
> + * Copyright (c) 2024 Daniel Golle <daniel@makrotopia.org>
> + *                    Bc-bocun Chen <bc-bocun.chen@mediatek.com>
> + * based on mtk_usxgmii.c found in MediaTek's SDK released under
> GPL-2.0
> + * Copyright (c) 2022 MediaTek Inc.
> + * Author: Henry Yen <henry.yen@mediatek.com>
> + */
> +
> +#include <linux/module.h>
> +#include <linux/device.h>
> +#include <linux/platform_device.h>
> +#include <linux/of.h>
> +#include <linux/io.h>
> +#include <linux/clk.h>
> +#include <linux/reset.h>
> +#include <linux/phy.h>
> +#include <linux/phy/phy.h>
> +
> +#define MTK_XFI_TPHY_NUM_CLOCKS2
> +
> +#define REG_DIG_GLB_700x0070
> +#define  XTP_PCS_RX_EQ_IN_PROGRESS(x)FIELD_PREP(GENMASK(25, 24),
> (x))
> +#define  XTP_PCS_MODE_MASKGENMASK(17, 16)
> +#define  XTP_PCS_MODE(x)FIELD_PREP(GENMASK(17, 16), (x))
> +#define  XTP_PCS_RST_BBIT(15)
> +#define  XTP_FRC_PCS_RST_BBIT(14)
> +#define  XTP_PCS_PWD_SYNC_MASKGENMASK(13, 12)
> +#define  XTP_PCS_PWD_SYNC(x)FIELD_PREP(XTP_PCS_PWD_SYNC_MASK, (x))
> +#define  XTP_PCS_PWD_ASYNC_MASKGENMASK(11, 10)
> +#define  XTP_PCS_PWD_ASYNC(x)FIELD_PREP(XTP_PCS_PWD_ASYNC_MASK, (x))
> +#define  XTP_FRC_PCS_PWD_ASYNCBIT(8)
> +#define  XTP_PCS_UPDTBIT(4)
> +#define  XTP_PCS_IN_FR_RGBIT(0)
> +
> +#define REG_DIG_GLB_F40x00f4
> +#define  XFI_DPHY_PCS_SELBIT(0)
> +#define   XFI_DPHY_PCS_SEL_SGMIIFIELD_PREP(XFI_DPHY_PCS_SEL, 1)
> +#define   XFI_DPHY_PCS_SEL_USXGMIIFIELD_PREP(XFI_DPHY_PCS_SEL, 0)
> +#define  XFI_DPHY_AD_SGDT_FRC_ENBIT(5)
> +
> +#define REG_DIG_LN_TRX_400x3040
> +#define  XTP_LN_FRC_TX_DATA_ENBIT(29)
> +#define  XTP_LN_TX_DATA_ENBIT(28)
> +
> +#define REG_DIG_LN_TRX_B00x30b0
> +#define  XTP_LN_FRC_TX_MACCK_ENBIT(5)
> +#define  XTP_LN_TX_MACCK_ENBIT(4)
> +
> +#define REG_ANA_GLB_D00x90d0
> +#define  XTP_GLB_USXGMII_SEL_MASKGENMASK(3, 1)
> +#define  XTP_GLB_USXGMII_SEL(x)FIELD_PREP(GENMASK(3, 1), (x))
> +#define  XTP_GLB_USXGMII_ENBIT(0)
> +
> +struct mtk_xfi_tphy {
> +void __iomem*base;
> +struct device*dev;
> +struct reset_control*reset;
> +struct clk_bulk_dataclocks[MTK_XFI_TPHY_NUM_CLOCKS];
> +boolda_war;
> +};
> +
> +static void mtk_xfi_tphy_write(struct mtk_xfi_tphy *xfi_tphy, u16
> reg,
> +       u32 value)
> +{
> +iowrite32(value, xfi_tphy->base + reg);
> +}
> +
> +static void mtk_xfi_tphy_rmw(struct mtk_xfi_tphy *xfi_tphy, u16 reg,
> +     u32 clr, u32 set)
> +{
> +u32 val;
> +
> +val = ioread32(xfi_tphy->base + reg);
> +val &= ~clr;
> +val |= set;
> +iowrite32(val, xfi_tphy->base + reg);
> +}
> +
> +static void mtk_xfi_tphy_set(struct mtk_xfi_tphy *xfi_tphy, u16 reg,
> +     u32 set)
> +{
> +mtk_xfi_tphy_rmw(xfi_tphy, reg, 0, set);
> +}
> +
> +static void mtk_xfi_tphy_clear(struct mtk_xfi_tphy *xfi_tphy, u16
> reg,
> +       u32 clr)
> +{
> +mtk_xfi_tphy_rmw(xfi_tphy, reg, clr, 0);
> +}

Helpers defined in phy-mtk-io.h can be used instead?

> +
> +static void mtk_xfi_tphy_setup(struct mtk_xfi_tphy *xfi_tphy,
> +       phy_interface_t interface)
> +{
> +bool is_2p5g = (interface == PHY_INTERFACE_MODE_2500BASEX);
> +bool is_1g = (interface == PHY_INTERFACE_MODE_1000BASEX ||
> +      interface == PHY_INTERFACE_MODE_SGMII);
> +bool is_10g = (interface == PHY_INTERFACE_MODE_10GBASER ||
> +       interface == PHY_INTERFACE_MODE_USXGMII);
> +bool is_5g = (interface == PHY_INTERFACE_MODE_5GBASER);
> +bool is_xgmii = (is_10g || is_5g);
> +
> +dev_dbg(xfi_tphy->dev, "setting up for mode %s\n",
> phy_modes(interface));
> +
> +/* Setup PLL setting */
> +mtk_xfi_tphy_rmw(xfi_tphy, 0x9024, 0x100000, is_10g ? 0x0 :
> 0x100000);
> +mtk_xfi_tphy_rmw(xfi_tphy, 0x2020, 0x202000, is_5g ? 0x202000 :
> 0x0);
> +mtk_xfi_tphy_rmw(xfi_tphy, 0x2030, 0x500, is_1g ? 0x0 : 0x500);
> +mtk_xfi_tphy_rmw(xfi_tphy, 0x2034, 0xa00, is_1g ? 0x0 : 0xa00);
> +mtk_xfi_tphy_rmw(xfi_tphy, 0x2040, 0x340000, is_1g ? 0x200000 :
> +     0x140000);
> +
> +/* Setup RXFE BW setting */
> +mtk_xfi_tphy_rmw(xfi_tphy, 0x50f0, 0xc10, is_1g ? 0x410 :
> +  is_5g ? 0x800 : 0x400);
> +mtk_xfi_tphy_rmw(xfi_tphy, 0x50e0, 0x4000, is_5g ? 0x0 : 0x4000);
> +
> +/* Setup RX CDR setting */
> +mtk_xfi_tphy_rmw(xfi_tphy, 0x506c, 0x30000, is_5g ? 0x0 : 0x30000);
> +mtk_xfi_tphy_rmw(xfi_tphy, 0x5070, 0x670000, is_5g ? 0x620000 :
> 0x50000);
> +mtk_xfi_tphy_rmw(xfi_tphy, 0x5074, 0x180000, is_5g ? 0x180000 :
> 0x0);
> +mtk_xfi_tphy_rmw(xfi_tphy, 0x5078, 0xf000400, is_5g ? 0x8000000 :
> +      0x7000400);
> +mtk_xfi_tphy_rmw(xfi_tphy, 0x507c, 0x5000500, is_5g ? 0x4000400 :
> +      0x1000100);
> +mtk_xfi_tphy_rmw(xfi_tphy, 0x5080, 0x1410, is_1g ? 0x400 :
> +   is_5g ? 0x1010 : 0x0);
> +mtk_xfi_tphy_rmw(xfi_tphy, 0x5084, 0x30300, is_1g ? 0x30300 :
> +    is_5g ? 0x30100 :
> +    0x100);
> +mtk_xfi_tphy_rmw(xfi_tphy, 0x5088, 0x60200, is_1g ? 0x20200 :
> + is_5g ? 0x40000 :
> + 0x20000);
> +
> +/* Setting RXFE adaptation range setting */
> +mtk_xfi_tphy_rmw(xfi_tphy, 0x50e4, 0xc0000, is_5g ? 0x0 : 0xc0000);
> +mtk_xfi_tphy_rmw(xfi_tphy, 0x50e8, 0x40000, is_5g ? 0x0 : 0x40000);
> +mtk_xfi_tphy_rmw(xfi_tphy, 0x50ec, 0xa00, is_1g ? 0x200 : 0x800);
> +mtk_xfi_tphy_rmw(xfi_tphy, 0x50a8, 0xee0000, is_5g ? 0x800000 :
> +     0x6e0000);
> +mtk_xfi_tphy_rmw(xfi_tphy, 0x6004, 0x190000, is_5g ? 0x0 :
> 0x190000);
> +if (is_10g)
> +mtk_xfi_tphy_write(xfi_tphy, 0x00f8, 0x01423342);
> +else if (is_5g)
> +mtk_xfi_tphy_write(xfi_tphy, 0x00f8, 0x00a132a1);
> +else if (is_2p5g)
> +mtk_xfi_tphy_write(xfi_tphy, 0x00f8, 0x009c329c);
> +else
> +mtk_xfi_tphy_write(xfi_tphy, 0x00f8, 0x00fa32fa);
Still have many magic number.

> +
> +/* Force SGDT_OUT off and select PCS */
> +mtk_xfi_tphy_rmw(xfi_tphy, REG_DIG_GLB_F4,
> + XFI_DPHY_AD_SGDT_FRC_EN | XFI_DPHY_PCS_SEL,
> + XFI_DPHY_AD_SGDT_FRC_EN |
> + (is_xgmii ? XFI_DPHY_PCS_SEL_USXGMII :
> +     XFI_DPHY_PCS_SEL_SGMII));
> +
> +
> +/* Force GLB_CKDET_OUT */
> +mtk_xfi_tphy_set(xfi_tphy, 0x0030, 0xc00);
> +
> +/* Force AEQ on */
> +mtk_xfi_tphy_write(xfi_tphy, REG_DIG_GLB_70,
> +   XTP_PCS_RX_EQ_IN_PROGRESS(2) |
> +   XTP_PCS_PWD_SYNC(2) |
> +   XTP_PCS_PWD_ASYNC(2));
> +
> +usleep_range(1, 5);
> +
> +/* Setup TX DA default value */
> +mtk_xfi_tphy_rmw(xfi_tphy, 0x30b0, 0x30, 0x20);
> +mtk_xfi_tphy_write(xfi_tphy, 0x3028, 0x00008a01);
> +mtk_xfi_tphy_write(xfi_tphy, 0x302c, 0x0000a884);
> +mtk_xfi_tphy_write(xfi_tphy, 0x3024, 0x00083002);
> +
> +/* Setup RG default value */
> +if (is_xgmii) {
> +mtk_xfi_tphy_write(xfi_tphy, 0x3010, 0x00022220);
> +mtk_xfi_tphy_write(xfi_tphy, 0x5064, 0x0f020a01);
> +mtk_xfi_tphy_write(xfi_tphy, 0x50b4, 0x06100600);
> +if (interface == PHY_INTERFACE_MODE_USXGMII)
> +mtk_xfi_tphy_write(xfi_tphy, 0x3048, 0x40704000);
> +else
> +mtk_xfi_tphy_write(xfi_tphy, 0x3048, 0x47684100);
> +} else {
> +mtk_xfi_tphy_write(xfi_tphy, 0x3010, 0x00011110);
> +mtk_xfi_tphy_write(xfi_tphy, 0x3048, 0x40704000);
> +}
> +
> +if (is_1g)
> +mtk_xfi_tphy_write(xfi_tphy, 0x3064, 0x0000c000);
> +
> +/* Setup RX EQ initial value */
> +mtk_xfi_tphy_rmw(xfi_tphy, 0x3050, 0xa8000000,
> + (interface != PHY_INTERFACE_MODE_10GBASER) ?
> +  0xa8000000 : 0x0);
> +mtk_xfi_tphy_rmw(xfi_tphy, 0x3054, 0xaa,
> + (interface != PHY_INTERFACE_MODE_10GBASER) ?
> +  0xaa : 0x0);
> +
> +if (is_xgmii)
> +mtk_xfi_tphy_write(xfi_tphy, 0x306c, 0x00000f00);
> +else if (is_2p5g)
> +mtk_xfi_tphy_write(xfi_tphy, 0x306c, 0x22000f00);
> +else
> +mtk_xfi_tphy_write(xfi_tphy, 0x306c, 0x20200f00);
> +
> +if (interface == PHY_INTERFACE_MODE_10GBASER && xfi_tphy->da_war)
> +mtk_xfi_tphy_rmw(xfi_tphy, 0xa008, 0x10000, 0x10000);
> +
> +mtk_xfi_tphy_rmw(xfi_tphy, 0xa060, 0x50000, is_xgmii ? 0x40000 :
> +       0x50000);
> +
> +/* Setup PHYA speed */
> +mtk_xfi_tphy_rmw(xfi_tphy, REG_ANA_GLB_D0,
> + XTP_GLB_USXGMII_SEL_MASK | XTP_GLB_USXGMII_EN,
> + is_10g ?  XTP_GLB_USXGMII_SEL(0) :
> + is_5g ?   XTP_GLB_USXGMII_SEL(1) :
> + is_2p5g ? XTP_GLB_USXGMII_SEL(2) :
> +   XTP_GLB_USXGMII_SEL(3));
> +mtk_xfi_tphy_set(xfi_tphy, REG_ANA_GLB_D0, XTP_GLB_USXGMII_EN);
> +
> +/* Release reset */
> +mtk_xfi_tphy_set(xfi_tphy, REG_DIG_GLB_70,
> + XTP_PCS_RST_B | XTP_FRC_PCS_RST_B);
> +usleep_range(150, 500);
> +
> +/* Switch to P0 */
> +mtk_xfi_tphy_rmw(xfi_tphy, REG_DIG_GLB_70,
> + XTP_PCS_PWD_SYNC_MASK |
> + XTP_PCS_PWD_ASYNC_MASK,
> + XTP_FRC_PCS_PWD_ASYNC |
> + XTP_PCS_UPDT | XTP_PCS_IN_FR_RG);
> +usleep_range(1, 5);
> +
> +mtk_xfi_tphy_clear(xfi_tphy, REG_DIG_GLB_70, XTP_PCS_UPDT);
> +usleep_range(15, 50);
> +
> +if (is_xgmii) {
> +/* Switch to Gen3 */
> +mtk_xfi_tphy_rmw(xfi_tphy, REG_DIG_GLB_70,
> + XTP_PCS_MODE_MASK | XTP_PCS_UPDT,
> + XTP_PCS_MODE(2) | XTP_PCS_UPDT);
> +} else {
> +/* Switch to Gen2 */
> +mtk_xfi_tphy_rmw(xfi_tphy, REG_DIG_GLB_70,
> + XTP_PCS_MODE_MASK | XTP_PCS_UPDT,
> + XTP_PCS_MODE(1) | XTP_PCS_UPDT);
> +}
> +usleep_range(1, 5);
> +
> +mtk_xfi_tphy_clear(xfi_tphy, REG_DIG_GLB_70, XTP_PCS_UPDT);
> +
> +usleep_range(100, 500);
> +
> +/* Enable MAC CK */
> +mtk_xfi_tphy_set(xfi_tphy, REG_DIG_LN_TRX_B0, XTP_LN_TX_MACCK_EN);
> +mtk_xfi_tphy_clear(xfi_tphy, REG_DIG_GLB_F4,
> XFI_DPHY_AD_SGDT_FRC_EN);
> +
> +/* Enable TX data */
> +mtk_xfi_tphy_set(xfi_tphy, REG_DIG_LN_TRX_40,
> + XTP_LN_FRC_TX_DATA_EN | XTP_LN_TX_DATA_EN);
> +usleep_range(400, 1000);
> +}
> +
> +static int mtk_xfi_tphy_set_mode(struct phy *phy, enum phy_mode
> mode, int
> + submode)
> +{
> +struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy);
> +
> +if (mode != PHY_MODE_ETHERNET)
> +return -EINVAL;
> +
> +switch (submode) {
> +case PHY_INTERFACE_MODE_1000BASEX:
> +case PHY_INTERFACE_MODE_2500BASEX:
> +case PHY_INTERFACE_MODE_SGMII:
> +case PHY_INTERFACE_MODE_5GBASER:
> +case PHY_INTERFACE_MODE_10GBASER:
> +case PHY_INTERFACE_MODE_USXGMII:
> +mtk_xfi_tphy_setup(xfi_tphy, submode);
> +return 0;
> +default:
> +return -EINVAL;
> +}
> +}
> +
> +static int mtk_xfi_tphy_reset(struct phy *phy)
> +{
> +struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy);
> +
> +reset_control_assert(xfi_tphy->reset);
> +usleep_range(100, 500);
> +reset_control_deassert(xfi_tphy->reset);
> +usleep_range(1, 10);
> +
> +return 0;
> +}
> +
> +static int mtk_xfi_tphy_power_on(struct phy *phy)
> +{
> +struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy);
> +
> +return clk_bulk_prepare_enable(MTK_XFI_TPHY_NUM_CLOCKS, xfi_tphy-
> >clocks);
> +}
> +
> +static int mtk_xfi_tphy_power_off(struct phy *phy)
> +{
> +struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy);
> +
> +clk_bulk_disable_unprepare(MTK_XFI_TPHY_NUM_CLOCKS, xfi_tphy-
> >clocks);
> +
> +return 0;
> +}
> +
> +static const struct phy_ops mtk_xfi_tphy_ops = {
> +.power_on= mtk_xfi_tphy_power_on,
> +.power_off= mtk_xfi_tphy_power_off,
> +.set_mode= mtk_xfi_tphy_set_mode,
> +.reset= mtk_xfi_tphy_reset,
> +.owner= THIS_MODULE,
> +};
> +
> +static int mtk_xfi_tphy_probe(struct platform_device *pdev)
> +{
> +struct device_node *np = pdev->dev.of_node;
> +struct phy_provider *phy_provider;
> +struct mtk_xfi_tphy *xfi_tphy;
> +struct phy *phy;
> +
> +if (!np)
> +return -ENODEV;
> +
> +xfi_tphy = devm_kzalloc(&pdev->dev, sizeof(*xfi_tphy), GFP_KERNEL);
> +if (!xfi_tphy)
> +return -ENOMEM;
> +
> +xfi_tphy->base = devm_of_iomap(&pdev->dev, np, 0, NULL);
> +if (!xfi_tphy->base)
> +return -EIO;
> +
> +xfi_tphy->dev = &pdev->dev;
> +
> +xfi_tphy->clocks[0].id = "topxtal";
> +xfi_tphy->clocks[0].clk = devm_clk_get(&pdev->dev, xfi_tphy-
> >clocks[0].id);
> +if (IS_ERR(xfi_tphy->clocks[0].clk))
> +return PTR_ERR(xfi_tphy->clocks[0].clk);
> +
> +xfi_tphy->clocks[1].id = "xfipll";
> +xfi_tphy->clocks[1].clk = devm_clk_get(&pdev->dev, xfi_tphy-
> >clocks[1].id);
> +if (IS_ERR(xfi_tphy->clocks[1].clk))
> +return PTR_ERR(xfi_tphy->clocks[1].clk);
> +
> +xfi_tphy->reset = devm_reset_control_get_exclusive(&pdev->dev,
> NULL);
> +if (IS_ERR(xfi_tphy->reset))
> +return PTR_ERR(xfi_tphy->reset);
> +
> +xfi_tphy->da_war = of_property_read_bool(np,
> + "mediatek,usxgmii-performance-errata");
> +
> +phy = devm_phy_create(&pdev->dev, NULL, &mtk_xfi_tphy_ops);
> +if (IS_ERR(phy))
> +return PTR_ERR(phy);
> +
> +phy_set_drvdata(phy, xfi_tphy);
> +
> +phy_provider = devm_of_phy_provider_register(&pdev->dev,
> +     of_phy_simple_xlate);
> +
> +return PTR_ERR_OR_ZERO(phy_provider);
> +}
> +
> +static const struct of_device_id mtk_xfi_tphy_match[] = {
> +{ .compatible = "mediatek,mt7988-xfi-tphy", },
> +{ }
> +};
> +MODULE_DEVICE_TABLE(of, mtk_xfi_tphy_match);
> +
> +static struct platform_driver mtk_xfi_tphy_driver = {
> +.probe = mtk_xfi_tphy_probe,
> +.driver = {
> +.name = "mtk-xfi-tphy",
> +.of_match_table = mtk_xfi_tphy_match,
> +},
> +};
> +module_platform_driver(mtk_xfi_tphy_driver);
> +
> +MODULE_DESCRIPTION("MediaTek XFI T-PHY driver");
> +MODULE_AUTHOR("Daniel Golle <daniel@makrotopia.org>");
> +MODULE_AUTHOR("Bc-bocun Chen <bc-bocun.chen@mediatek.com>");
> +MODULE_LICENSE("GPL");
> -- 
> 2.43.0
  
AngeloGioacchino Del Regno Feb. 5, 2024, 3:26 p.m. UTC | #2
Il 02/02/24 17:33, Daniel Golle ha scritto:
> Hi Angelo,
> 
> thank you for promptly reviewing my submission and providing valuable
> feedback!
> 
> On Fri, Feb 02, 2024 at 02:21:48PM +0100, AngeloGioacchino Del Regno wrote:
>> Il 01/02/24 22:53, Daniel Golle ha scritto:
>>> Add driver for MediaTek's XFI T-PHY, 10 Gigabit/s Ethernet SerDes PHY
>>> which can be found in the MT7988 SoC.
>>>
>>> The PHY can operates only in PHY_MODE_ETHERNET, the submode is one of
>>> PHY_INTERFACE_MODE_* corresponding to the supported modes:
>>>
>>>    * USXGMII                 \
>>>    * 10GBase-R                }- USXGMII PCS - XGDM  \
>>>    * 5GBase-R                /                        \
>>>                                                        }- Ethernet MAC
>>>    * 2500Base-X              \                        /
>>>    * 1000Base-X               }- LynxI PCS - GDM     /
>>>    * Cisco SGMII (MAC side)  /
>>>
>>> In order to work-around a performance issue present on the first of
>>> two XFI T-PHYs present in MT7988, special tuning is applied which can be
>>> selected by adding the 'mediatek,usxgmii-performance-errata' property to
>>> the device tree node.
>>>
>>> There is no documentation for most registers used for the
>>> analog/tuning part, however, most of the registers have been partially
>>> reverse-engineered from MediaTek's SDK implementation (an opaque
>>> sequence of 32-bit register writes) and descriptions for all relevant
>>> digital registers and bits such as resets and muxes have been supplied
>>> by MediaTek.
>>>
>>> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
>>> ---
>>>    MAINTAINERS                             |   1 +
>>>    drivers/phy/mediatek/Kconfig            |  12 +
>>>    drivers/phy/mediatek/Makefile           |   1 +
>>>    drivers/phy/mediatek/phy-mtk-xfi-tphy.c | 392 ++++++++++++++++++++++++
>>>    4 files changed, 406 insertions(+)
>>>    create mode 100644 drivers/phy/mediatek/phy-mtk-xfi-tphy.c
>>>
>>> diff --git a/MAINTAINERS b/MAINTAINERS
>>> index 52769631bdb1a..52e4192470bd9 100644
>>> --- a/MAINTAINERS
>>> +++ b/MAINTAINERS
>>> @@ -13715,6 +13715,7 @@ L:	netdev@vger.kernel.org
>>>    S:	Maintained
>>>    F:	drivers/net/phy/mediatek-ge-soc.c
>>>    F:	drivers/net/phy/mediatek-ge.c
>>> +F:	drivers/phy/mediatek/phy-mtk-xfi-tphy.c
>>>    MEDIATEK I2C CONTROLLER DRIVER
>>>    M:	Qii Wang <qii.wang@mediatek.com>
>>> diff --git a/drivers/phy/mediatek/Kconfig b/drivers/phy/mediatek/Kconfig
>>> index 3125ecb5d119f..5161d130c7f8b 100644
>>> --- a/drivers/phy/mediatek/Kconfig
>>> +++ b/drivers/phy/mediatek/Kconfig
>>> @@ -13,6 +13,18 @@ config PHY_MTK_PCIE
>>>    	  callback for PCIe GEN3 port, it supports software efuse
>>>    	  initialization.
>>> +config PHY_MTK_XFI_TPHY
>>> +	tristate "MediaTek XFI T-PHY Driver"
>>> +	depends on ARCH_MEDIATEK || COMPILE_TEST
>>> +	depends on OF && OF_ADDRESS
>>> +	depends on HAS_IOMEM
>>> +	select GENERIC_PHY
>>> +	help
>>> +	  Say 'Y' here to add support for MediaTek XFI T-PHY driver.
>>> +	  The driver provides access to the Ethernet SerDes T-PHY supporting
>>> +	  1GE and 2.5GE modes via the LynxI PCS, and 5GE and 10GE modes
>>> +	  via the USXGMII PCS found in MediaTek SoCs with 10G Ethernet.
>>> +
>>>    config PHY_MTK_TPHY
>>>    	tristate "MediaTek T-PHY Driver"
>>>    	depends on ARCH_MEDIATEK || COMPILE_TEST
>>> diff --git a/drivers/phy/mediatek/Makefile b/drivers/phy/mediatek/Makefile
>>> index c9a50395533eb..fa7217178e7f4 100644
>>> --- a/drivers/phy/mediatek/Makefile
>>> +++ b/drivers/phy/mediatek/Makefile
>>> @@ -8,6 +8,7 @@ obj-$(CONFIG_PHY_MTK_PCIE)		+= phy-mtk-pcie.o
>>>    obj-$(CONFIG_PHY_MTK_TPHY)		+= phy-mtk-tphy.o
>>>    obj-$(CONFIG_PHY_MTK_UFS)		+= phy-mtk-ufs.o
>>>    obj-$(CONFIG_PHY_MTK_XSPHY)		+= phy-mtk-xsphy.o
>>> +obj-$(CONFIG_PHY_MTK_XFI_TPHY)		+= phy-mtk-xfi-tphy.o
>>>    phy-mtk-hdmi-drv-y			:= phy-mtk-hdmi.o
>>>    phy-mtk-hdmi-drv-y			+= phy-mtk-hdmi-mt2701.o
>>> diff --git a/drivers/phy/mediatek/phy-mtk-xfi-tphy.c b/drivers/phy/mediatek/phy-mtk-xfi-tphy.c
>>> new file mode 100644
>>> index 0000000000000..d50e6320860e5
>>> --- /dev/null
>>> +++ b/drivers/phy/mediatek/phy-mtk-xfi-tphy.c
>>> @@ -0,0 +1,392 @@
>>> +// SPDX-License-Identifier: GPL-2.0-or-later
>>> +/* MediaTek 10GE SerDes PHY driver
>>
>> MediaTek 10GE SerDes XFI T-PHY driver ?
> 
> Ack. Will unify the name accross all files.
> 
>>
>>> + *
>>> + * Copyright (c) 2024 Daniel Golle <daniel@makrotopia.org>
>>> + *                    Bc-bocun Chen <bc-bocun.chen@mediatek.com>
>>> + * based on mtk_usxgmii.c found in MediaTek's SDK released under GPL-2.0
>>> + * Copyright (c) 2022 MediaTek Inc.
>>> + * Author: Henry Yen <henry.yen@mediatek.com>
>>> + */
>>> +
>>> +#include <linux/module.h>
>>> +#include <linux/device.h>
>>> +#include <linux/platform_device.h>
>>> +#include <linux/of.h>
>>> +#include <linux/io.h>
>>> +#include <linux/clk.h>
>>> +#include <linux/reset.h>
>>> +#include <linux/phy.h>
>>> +#include <linux/phy/phy.h>
>>> +
>>> +#define MTK_XFI_TPHY_NUM_CLOCKS		2
>>> +
>>> +#define REG_DIG_GLB_70			0x0070
>>> +#define  XTP_PCS_RX_EQ_IN_PROGRESS(x)	FIELD_PREP(GENMASK(25, 24), (x))
>>> +#define  XTP_PCS_MODE_MASK		GENMASK(17, 16)
>>> +#define  XTP_PCS_MODE(x)		FIELD_PREP(GENMASK(17, 16), (x))
>>> +#define  XTP_PCS_RST_B			BIT(15)
>>> +#define  XTP_FRC_PCS_RST_B		BIT(14)
>>> +#define  XTP_PCS_PWD_SYNC_MASK		GENMASK(13, 12)
>>> +#define  XTP_PCS_PWD_SYNC(x)		FIELD_PREP(XTP_PCS_PWD_SYNC_MASK, (x))
>>> +#define  XTP_PCS_PWD_ASYNC_MASK		GENMASK(11, 10)
>>> +#define  XTP_PCS_PWD_ASYNC(x)		FIELD_PREP(XTP_PCS_PWD_ASYNC_MASK, (x))
>>> +#define  XTP_FRC_PCS_PWD_ASYNC		BIT(8)
>>> +#define  XTP_PCS_UPDT			BIT(4)
>>> +#define  XTP_PCS_IN_FR_RG		BIT(0)
>>> +
>>> +#define REG_DIG_GLB_F4			0x00f4
>>> +#define  XFI_DPHY_PCS_SEL		BIT(0)
>>> +#define   XFI_DPHY_PCS_SEL_SGMII	FIELD_PREP(XFI_DPHY_PCS_SEL, 1)
>>> +#define   XFI_DPHY_PCS_SEL_USXGMII	FIELD_PREP(XFI_DPHY_PCS_SEL, 0)
>>> +#define  XFI_DPHY_AD_SGDT_FRC_EN	BIT(5)
>>> +
>>> +#define REG_DIG_LN_TRX_40		0x3040
>>> +#define  XTP_LN_FRC_TX_DATA_EN		BIT(29)
>>> +#define  XTP_LN_TX_DATA_EN		BIT(28)
>>> +
>>> +#define REG_DIG_LN_TRX_B0		0x30b0
>>> +#define  XTP_LN_FRC_TX_MACCK_EN		BIT(5)
>>> +#define  XTP_LN_TX_MACCK_EN		BIT(4)
>>> +
>>> +#define REG_ANA_GLB_D0			0x90d0
>>> +#define  XTP_GLB_USXGMII_SEL_MASK	GENMASK(3, 1)
>>> +#define  XTP_GLB_USXGMII_SEL(x)		FIELD_PREP(GENMASK(3, 1), (x))
>>> +#define  XTP_GLB_USXGMII_EN		BIT(0)
>>> +
>>> +struct mtk_xfi_tphy {
>>> +	void __iomem		*base;
>>> +	struct device		*dev;
>>> +	struct reset_control	*reset;
>>> +	struct clk_bulk_data	clocks[MTK_XFI_TPHY_NUM_CLOCKS];
>>> +	bool			da_war;
>>> +};
>>> +
>>> +static void mtk_xfi_tphy_write(struct mtk_xfi_tphy *xfi_tphy, u16 reg,
>>> +			       u32 value)
>>> +{
>>> +	iowrite32(value, xfi_tphy->base + reg);
>>> +}
>>> +
>>> +static void mtk_xfi_tphy_rmw(struct mtk_xfi_tphy *xfi_tphy, u16 reg,
>>> +			     u32 clr, u32 set)
>>> +{
>>> +	u32 val;
>>> +
>>> +	val = ioread32(xfi_tphy->base + reg);
>>> +	val &= ~clr;
>>> +	val |= set;
>>> +	iowrite32(val, xfi_tphy->base + reg);
>>> +}
>>> +
>>> +static void mtk_xfi_tphy_set(struct mtk_xfi_tphy *xfi_tphy, u16 reg,
>>> +			     u32 set)
>>> +{
>>> +	mtk_xfi_tphy_rmw(xfi_tphy, reg, 0, set);
>>> +}
>>> +
>>> +static void mtk_xfi_tphy_clear(struct mtk_xfi_tphy *xfi_tphy, u16 reg,
>>> +			       u32 clr)
>>> +{
>>> +	mtk_xfi_tphy_rmw(xfi_tphy, reg, clr, 0);
>>> +}
>>> +
>>> +static void mtk_xfi_tphy_setup(struct mtk_xfi_tphy *xfi_tphy,
>>> +			       phy_interface_t interface)
>>> +{
>>> +	bool is_2p5g = (interface == PHY_INTERFACE_MODE_2500BASEX);
>>> +	bool is_1g = (interface == PHY_INTERFACE_MODE_1000BASEX ||
>>> +		      interface == PHY_INTERFACE_MODE_SGMII);
>>> +	bool is_10g = (interface == PHY_INTERFACE_MODE_10GBASER ||
>>> +		       interface == PHY_INTERFACE_MODE_USXGMII);
>>> +	bool is_5g = (interface == PHY_INTERFACE_MODE_5GBASER);
>>> +	bool is_xgmii = (is_10g || is_5g);
>>
>> is_usxgmii, I'd say.
> 
> This boolean is mostly used to destinguish which path to use at the
> T-junction of the PHY, ie. up to 2500Base-X goes to LynxI PCS while
> 5GBase-R, 10GBase-R and USXGMII go to USXGMII PCS (which handles all
> three modes and not just USXGMII).
> 
> Calling the boolean 'is_usxgmii' is a bit confusing as it not only
> means (interface == interface == PHY_INTERFACE_MODE_USXGMII) but
> rather also covers (interface == PHY_INTERFACE_MODE_10GBASER) as well
> as (interface == PHY_INTERFACE_MODE_5GBASER) which are not USXGMII.
> 
> Maybe we invert it and call it 'use_lynxi_pcs' instead?
> 

Since you were able to provide such a good explanation of that, I wonder why
you didn't add that as a comment in the code?

That way, there will be no confusion for sure, even if you keep "is_xgmii" :-)

>>
>>> +
>>> +	dev_dbg(xfi_tphy->dev, "setting up for mode %s\n", phy_modes(interface));
>>> +
>>> +	/* Setup PLL setting */
>>> +	mtk_xfi_tphy_rmw(xfi_tphy, 0x9024, 0x100000, is_10g ? 0x0 : 0x100000);
>>> +	mtk_xfi_tphy_rmw(xfi_tphy, 0x2020, 0x202000, is_5g ? 0x202000 : 0x0);
>>> +	mtk_xfi_tphy_rmw(xfi_tphy, 0x2030, 0x500, is_1g ? 0x0 : 0x500);
>>> +	mtk_xfi_tphy_rmw(xfi_tphy, 0x2034, 0xa00, is_1g ? 0x0 : 0xa00);
>>> +	mtk_xfi_tphy_rmw(xfi_tphy, 0x2040, 0x340000, is_1g ? 0x200000 :
>>> +							     0x140000);
>>> +
>>> +	/* Setup RXFE BW setting */
>>> +	mtk_xfi_tphy_rmw(xfi_tphy, 0x50f0, 0xc10, is_1g ? 0x410 :
>>> +							  is_5g ? 0x800 : 0x400);
>>> +	mtk_xfi_tphy_rmw(xfi_tphy, 0x50e0, 0x4000, is_5g ? 0x0 : 0x4000);
>>> +
>>> +	/* Setup RX CDR setting */
>>> +	mtk_xfi_tphy_rmw(xfi_tphy, 0x506c, 0x30000, is_5g ? 0x0 : 0x30000);
>>> +	mtk_xfi_tphy_rmw(xfi_tphy, 0x5070, 0x670000, is_5g ? 0x620000 : 0x50000);
>>> +	mtk_xfi_tphy_rmw(xfi_tphy, 0x5074, 0x180000, is_5g ? 0x180000 : 0x0);
>>> +	mtk_xfi_tphy_rmw(xfi_tphy, 0x5078, 0xf000400, is_5g ? 0x8000000 :
>>> +							      0x7000400);
>>> +	mtk_xfi_tphy_rmw(xfi_tphy, 0x507c, 0x5000500, is_5g ? 0x4000400 :
>>> +							      0x1000100);
>>> +	mtk_xfi_tphy_rmw(xfi_tphy, 0x5080, 0x1410, is_1g ? 0x400 :
>>> +							   is_5g ? 0x1010 : 0x0);
>>> +	mtk_xfi_tphy_rmw(xfi_tphy, 0x5084, 0x30300, is_1g ? 0x30300 :
>>> +							    is_5g ? 0x30100 :
>>> +								    0x100);
>>> +	mtk_xfi_tphy_rmw(xfi_tphy, 0x5088, 0x60200, is_1g ? 0x20200 :
>>> +							 is_5g ? 0x40000 :
>>> +								 0x20000);
>>> +
>>> +	/* Setting RXFE adaptation range setting */
>>> +	mtk_xfi_tphy_rmw(xfi_tphy, 0x50e4, 0xc0000, is_5g ? 0x0 : 0xc0000);
>>> +	mtk_xfi_tphy_rmw(xfi_tphy, 0x50e8, 0x40000, is_5g ? 0x0 : 0x40000);
>>> +	mtk_xfi_tphy_rmw(xfi_tphy, 0x50ec, 0xa00, is_1g ? 0x200 : 0x800);
>>> +	mtk_xfi_tphy_rmw(xfi_tphy, 0x50a8, 0xee0000, is_5g ? 0x800000 :
>>> +							     0x6e0000);
>>> +	mtk_xfi_tphy_rmw(xfi_tphy, 0x6004, 0x190000, is_5g ? 0x0 : 0x190000);
>>> +	if (is_10g)
>>> +		mtk_xfi_tphy_write(xfi_tphy, 0x00f8, 0x01423342);
>>> +	else if (is_5g)
>>> +		mtk_xfi_tphy_write(xfi_tphy, 0x00f8, 0x00a132a1);
>>> +	else if (is_2p5g)
>>> +		mtk_xfi_tphy_write(xfi_tphy, 0x00f8, 0x009c329c);
>>> +	else
>>> +		mtk_xfi_tphy_write(xfi_tphy, 0x00f8, 0x00fa32fa);
>>> +
>>> +	/* Force SGDT_OUT off and select PCS */
>>> +	mtk_xfi_tphy_rmw(xfi_tphy, REG_DIG_GLB_F4,
>>> +			 XFI_DPHY_AD_SGDT_FRC_EN | XFI_DPHY_PCS_SEL,
>>> +			 XFI_DPHY_AD_SGDT_FRC_EN |
>>> +			 (is_xgmii ? XFI_DPHY_PCS_SEL_USXGMII :
>>> +				     XFI_DPHY_PCS_SEL_SGMII));
>>> +
>>> +
>>> +	/* Force GLB_CKDET_OUT */
>>> +	mtk_xfi_tphy_set(xfi_tphy, 0x0030, 0xc00);
>>> +
>>> +	/* Force AEQ on */
>>> +	mtk_xfi_tphy_write(xfi_tphy, REG_DIG_GLB_70,
>>> +			   XTP_PCS_RX_EQ_IN_PROGRESS(2) |
>>> +			   XTP_PCS_PWD_SYNC(2) |
>>> +			   XTP_PCS_PWD_ASYNC(2));
>>> +
>>> +	usleep_range(1, 5);
>>> +
>>> +	/* Setup TX DA default value */
>>> +	mtk_xfi_tphy_rmw(xfi_tphy, 0x30b0, 0x30, 0x20);
>>> +	mtk_xfi_tphy_write(xfi_tphy, 0x3028, 0x00008a01);
>>> +	mtk_xfi_tphy_write(xfi_tphy, 0x302c, 0x0000a884);
>>> +	mtk_xfi_tphy_write(xfi_tphy, 0x3024, 0x00083002);
>>> +
>>> +	/* Setup RG default value */
>>> +	if (is_xgmii) {
>>> +		mtk_xfi_tphy_write(xfi_tphy, 0x3010, 0x00022220);
>>> +		mtk_xfi_tphy_write(xfi_tphy, 0x5064, 0x0f020a01);
>>> +		mtk_xfi_tphy_write(xfi_tphy, 0x50b4, 0x06100600);
>>> +		if (interface == PHY_INTERFACE_MODE_USXGMII)
>>> +			mtk_xfi_tphy_write(xfi_tphy, 0x3048, 0x40704000);
>>> +		else
>>> +			mtk_xfi_tphy_write(xfi_tphy, 0x3048, 0x47684100);
>>> +	} else {
>>> +		mtk_xfi_tphy_write(xfi_tphy, 0x3010, 0x00011110);
>>> +		mtk_xfi_tphy_write(xfi_tphy, 0x3048, 0x40704000);
>>> +	}
>>> +
>>> +	if (is_1g)
>>> +		mtk_xfi_tphy_write(xfi_tphy, 0x3064, 0x0000c000);
>>> +
>>> +	/* Setup RX EQ initial value */
>>> +	mtk_xfi_tphy_rmw(xfi_tphy, 0x3050, 0xa8000000,
>>> +			 (interface != PHY_INTERFACE_MODE_10GBASER) ?
>>> +			  0xa8000000 : 0x0);
>>> +	mtk_xfi_tphy_rmw(xfi_tphy, 0x3054, 0xaa,
>>> +			 (interface != PHY_INTERFACE_MODE_10GBASER) ?
>>> +			  0xaa : 0x0);
>>> +
>>> +	if (is_xgmii)
>>> +		mtk_xfi_tphy_write(xfi_tphy, 0x306c, 0x00000f00);
>>> +	else if (is_2p5g)
>>> +		mtk_xfi_tphy_write(xfi_tphy, 0x306c, 0x22000f00);
>>> +	else
>>> +		mtk_xfi_tphy_write(xfi_tphy, 0x306c, 0x20200f00);
>>> +
>>> +	if (interface == PHY_INTERFACE_MODE_10GBASER && xfi_tphy->da_war)
>>> +		mtk_xfi_tphy_rmw(xfi_tphy, 0xa008, 0x10000, 0x10000);
>>> +
>>> +	mtk_xfi_tphy_rmw(xfi_tphy, 0xa060, 0x50000, is_xgmii ? 0x40000 :
>>> +							       0x50000);
>>> +
>>> +	/* Setup PHYA speed */
>>> +	mtk_xfi_tphy_rmw(xfi_tphy, REG_ANA_GLB_D0,
>>> +			 XTP_GLB_USXGMII_SEL_MASK | XTP_GLB_USXGMII_EN,
>>> +			 is_10g ?  XTP_GLB_USXGMII_SEL(0) :
>>> +			 is_5g ?   XTP_GLB_USXGMII_SEL(1) :
>>> +			 is_2p5g ? XTP_GLB_USXGMII_SEL(2) :
>>> +				   XTP_GLB_USXGMII_SEL(3));
>>> +	mtk_xfi_tphy_set(xfi_tphy, REG_ANA_GLB_D0, XTP_GLB_USXGMII_EN);
>>> +
>>> +	/* Release reset */
>>> +	mtk_xfi_tphy_set(xfi_tphy, REG_DIG_GLB_70,
>>> +			 XTP_PCS_RST_B | XTP_FRC_PCS_RST_B);
>>> +	usleep_range(150, 500);
>>> +
>>> +	/* Switch to P0 */
>>> +	mtk_xfi_tphy_rmw(xfi_tphy, REG_DIG_GLB_70,
>>> +			 XTP_PCS_PWD_SYNC_MASK |
>>> +			 XTP_PCS_PWD_ASYNC_MASK,
>>> +			 XTP_FRC_PCS_PWD_ASYNC |
>>> +			 XTP_PCS_UPDT | XTP_PCS_IN_FR_RG);
>>> +	usleep_range(1, 5);
>>> +
>>> +	mtk_xfi_tphy_clear(xfi_tphy, REG_DIG_GLB_70, XTP_PCS_UPDT);
>>> +	usleep_range(15, 50);
>>> +
>>> +	if (is_xgmii) {
>>> +		/* Switch to Gen3 */
>>> +		mtk_xfi_tphy_rmw(xfi_tphy, REG_DIG_GLB_70,
>>> +				 XTP_PCS_MODE_MASK | XTP_PCS_UPDT,
>>> +				 XTP_PCS_MODE(2) | XTP_PCS_UPDT);
>>> +	} else {
>>> +		/* Switch to Gen2 */
>>> +		mtk_xfi_tphy_rmw(xfi_tphy, REG_DIG_GLB_70,
>>> +				 XTP_PCS_MODE_MASK | XTP_PCS_UPDT,
>>> +				 XTP_PCS_MODE(1) | XTP_PCS_UPDT);
>>> +	}
>>> +	usleep_range(1, 5);
>>> +
>>> +	mtk_xfi_tphy_clear(xfi_tphy, REG_DIG_GLB_70, XTP_PCS_UPDT);
>>> +
>>> +	usleep_range(100, 500);
>>> +
>>> +	/* Enable MAC CK */
>>> +	mtk_xfi_tphy_set(xfi_tphy, REG_DIG_LN_TRX_B0, XTP_LN_TX_MACCK_EN);
>>> +	mtk_xfi_tphy_clear(xfi_tphy, REG_DIG_GLB_F4, XFI_DPHY_AD_SGDT_FRC_EN);
>>> +
>>> +	/* Enable TX data */
>>> +	mtk_xfi_tphy_set(xfi_tphy, REG_DIG_LN_TRX_40,
>>> +			 XTP_LN_FRC_TX_DATA_EN | XTP_LN_TX_DATA_EN);
>>> +	usleep_range(400, 1000);
>>> +}
>>> +
>>> +static int mtk_xfi_tphy_set_mode(struct phy *phy, enum phy_mode mode, int
>>> +				 submode)
>>> +{
>>> +	struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy);
>>> +
>>> +	if (mode != PHY_MODE_ETHERNET)
>>> +		return -EINVAL;
>>> +
>>> +	switch (submode) {
>>> +	case PHY_INTERFACE_MODE_1000BASEX:
>>
>> fallthrough;
> 
> I don't think so. No other kernel drivers are doing that and also there
> is no compiler warning what-so-ever when matching multiple cases in that
> way.
> 

Right. Just verified. Keep it like that then.

>>
>>> +	case PHY_INTERFACE_MODE_2500BASEX:
>>
>> fallthrough;
>>
>>> +	case PHY_INTERFACE_MODE_SGMII:
>>
>> ... etc :-)
>>
>>> +	case PHY_INTERFACE_MODE_5GBASER:
>>> +	case PHY_INTERFACE_MODE_10GBASER:
>>> +	case PHY_INTERFACE_MODE_USXGMII:
>>
>> Does this PHY support PHY_INTERFACE_MODE_XGMII ?
>>
>>> +		mtk_xfi_tphy_setup(xfi_tphy, submode);
>>> +		return 0;
>>> +	default:
>>> +		return -EINVAL;
>>> +	}
>>> +}
>>> +
>>> +static int mtk_xfi_tphy_reset(struct phy *phy)
>>> +{
>>> +	struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy);
>>> +
>>> +	reset_control_assert(xfi_tphy->reset);
>>> +	usleep_range(100, 500);
>>> +	reset_control_deassert(xfi_tphy->reset);
>>> +	usleep_range(1, 10);
>>> +
>>> +	return 0;
>>> +}
>>> +
>>> +static int mtk_xfi_tphy_power_on(struct phy *phy)
>>> +{
>>> +	struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy);
>>> +
>>> +	return clk_bulk_prepare_enable(MTK_XFI_TPHY_NUM_CLOCKS, xfi_tphy->clocks);
>>> +}
>>> +
>>> +static int mtk_xfi_tphy_power_off(struct phy *phy)
>>> +{
>>> +	struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy);
>>> +
>>> +	clk_bulk_disable_unprepare(MTK_XFI_TPHY_NUM_CLOCKS, xfi_tphy->clocks);
>>> +
>>> +	return 0;
>>> +}
>>> +
>>> +static const struct phy_ops mtk_xfi_tphy_ops = {
>>> +	.power_on	= mtk_xfi_tphy_power_on,
>>> +	.power_off	= mtk_xfi_tphy_power_off,
>>> +	.set_mode	= mtk_xfi_tphy_set_mode,
>>> +	.reset		= mtk_xfi_tphy_reset,
>>> +	.owner		= THIS_MODULE,
>>> +};
>>> +
>>> +static int mtk_xfi_tphy_probe(struct platform_device *pdev)
>>> +{
>>> +	struct device_node *np = pdev->dev.of_node;
>>> +	struct phy_provider *phy_provider;
>>> +	struct mtk_xfi_tphy *xfi_tphy;
>>> +	struct phy *phy;
>>> +
>>> +	if (!np)
>>> +		return -ENODEV;
>>> +
>>> +	xfi_tphy = devm_kzalloc(&pdev->dev, sizeof(*xfi_tphy), GFP_KERNEL);
>>> +	if (!xfi_tphy)
>>> +		return -ENOMEM;
>>> +
>>> +	xfi_tphy->base = devm_of_iomap(&pdev->dev, np, 0, NULL);
>>
>> Why devm_of_iomap() and not devm_platform_ioremap_resource()?
> 
> True, I will make use of devm_platform_ioremap_resource().
> 
>>
>>> +	if (!xfi_tphy->base)
>>> +		return -EIO;
>>> +
>>> +	xfi_tphy->dev = &pdev->dev;
>>> +
>>> +	xfi_tphy->clocks[0].id = "topxtal";
>>
>> xfi_tphy->clocks[0].id = "topxtal";
>> xfi_tphy->clocks[1].id = "xfipll";
>>
>> ret = devm_clk_bulk_get(&pdev->dev, MTK_XFI_TPHY_NUM_CLOCKS, xfi_tphy->clocks);
>> if (ret)
>> 	return ret;
>>
>> ...it's that simple :-P
> 
> Ok, thanks :)
> 
>>
>>> +	xfi_tphy->clocks[0].clk = devm_clk_get(&pdev->dev, xfi_tphy->clocks[0].id);
>>> +	if (IS_ERR(xfi_tphy->clocks[0].clk))
>>> +		return PTR_ERR(xfi_tphy->clocks[0].clk);
>>> +
>>> +	xfi_tphy->clocks[1].id = "xfipll";
>>> +	xfi_tphy->clocks[1].clk = devm_clk_get(&pdev->dev, xfi_tphy->clocks[1].id);
>>> +	if (IS_ERR(xfi_tphy->clocks[1].clk))
>>> +		return PTR_ERR(xfi_tphy->clocks[1].clk);
>>> +
>>> +	xfi_tphy->reset = devm_reset_control_get_exclusive(&pdev->dev, NULL);
>>> +	if (IS_ERR(xfi_tphy->reset))
>>> +		return PTR_ERR(xfi_tphy->reset);
>>> +
>>> +	xfi_tphy->da_war = of_property_read_bool(np,
>>> +						 "mediatek,usxgmii-performance-errata");
>>> +
>>
>> One line please
>>
>>> +	phy = devm_phy_create(&pdev->dev, NULL, &mtk_xfi_tphy_ops);
>>> +	if (IS_ERR(phy))
>>> +		return PTR_ERR(phy);
>>> +
>>> +	phy_set_drvdata(phy, xfi_tphy);
>>> +
>>> +	phy_provider = devm_of_phy_provider_register(&pdev->dev,
>>> +						     of_phy_simple_xlate);
>>
>> ditto
>>
>>> +
>>> +	return PTR_ERR_OR_ZERO(phy_provider);
>>> +}
>>> +
>>> +static const struct of_device_id mtk_xfi_tphy_match[] = {
>>> +	{ .compatible = "mediatek,mt7988-xfi-tphy", },
>>> +	{ }
>>
>> 	{ .compatible = "mediatek,mt7988-xfi-tphy" },
>> 	{ /* sentinel */ }
> 
> Ack.
> 
>>
>>> +};
>>> +MODULE_DEVICE_TABLE(of, mtk_xfi_tphy_match);
>>> +
>>> +static struct platform_driver mtk_xfi_tphy_driver = {
>>> +	.probe = mtk_xfi_tphy_probe,
>>> +	.driver = {
>>> +		.name = "mtk-xfi-tphy",
>>> +		.of_match_table = mtk_xfi_tphy_match,
>>> +	},
>>> +};
>>> +module_platform_driver(mtk_xfi_tphy_driver);
>>> +
>>> +MODULE_DESCRIPTION("MediaTek XFI T-PHY driver");
>>
>> MODULE_DESCRIPTION("MediaTek 10GE SerDes XFI T-PHY driver");
> 
> Ack, will unify the name everywhere.
> 
>>
>> Cheers,
>> Angelo
>>
>>> +MODULE_AUTHOR("Daniel Golle <daniel@makrotopia.org>");
>>> +MODULE_AUTHOR("Bc-bocun Chen <bc-bocun.chen@mediatek.com>");
>>> +MODULE_LICENSE("GPL");
>>
>>
  
AngeloGioacchino Del Regno Feb. 5, 2024, 3:29 p.m. UTC | #3
Il 04/02/24 07:29, Chunfeng Yun (云春峰) ha scritto:
> On Thu, 2024-02-01 at 21:53 +0000, Daniel Golle wrote:
>>   	
>> External email : Please do not click links or open attachments until
>> you have verified the sender or the content.
>>   Add driver for MediaTek's XFI T-PHY, 10 Gigabit/s Ethernet SerDes
>> PHY
>> which can be found in the MT7988 SoC.
>>
>> The PHY can operates only in PHY_MODE_ETHERNET, the submode is one of
>> PHY_INTERFACE_MODE_* corresponding to the supported modes:
>>
>>   * USXGMII                 \
>>   * 10GBase-R                }- USXGMII PCS - XGDM  \
>>   * 5GBase-R                /                        \
>>                                                       }- Ethernet MAC
>>   * 2500Base-X              \                        /
>>   * 1000Base-X               }- LynxI PCS - GDM     /
>>   * Cisco SGMII (MAC side)  /
>>
>> In order to work-around a performance issue present on the first of
>> two XFI T-PHYs present in MT7988, special tuning is applied which can
>> be
>> selected by adding the 'mediatek,usxgmii-performance-errata' property
>> to
>> the device tree node.
>>
>> There is no documentation for most registers used for the
>> analog/tuning part, however, most of the registers have been
>> partially
>> reverse-engineered from MediaTek's SDK implementation (an opaque
>> sequence of 32-bit register writes) and descriptions for all relevant
>> digital registers and bits such as resets and muxes have been
>> supplied
>> by MediaTek.
>>
>> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
>> ---
>>   MAINTAINERS                             |   1 +
>>   drivers/phy/mediatek/Kconfig            |  12 +
>>   drivers/phy/mediatek/Makefile           |   1 +
>>   drivers/phy/mediatek/phy-mtk-xfi-tphy.c | 392
>> ++++++++++++++++++++++++
>>   4 files changed, 406 insertions(+)
>>   create mode 100644 drivers/phy/mediatek/phy-mtk-xfi-tphy.c
>>
>> diff --git a/MAINTAINERS b/MAINTAINERS
>> index 52769631bdb1a..52e4192470bd9 100644
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -13715,6 +13715,7 @@ L:netdev@vger.kernel.org
>>   S:Maintained
>>   F:drivers/net/phy/mediatek-ge-soc.c
>>   F:drivers/net/phy/mediatek-ge.c
>> +F:drivers/phy/mediatek/phy-mtk-xfi-tphy.c
>>   
>>   MEDIATEK I2C CONTROLLER DRIVER
>>   M:Qii Wang <qii.wang@mediatek.com>
>> diff --git a/drivers/phy/mediatek/Kconfig
>> b/drivers/phy/mediatek/Kconfig
>> index 3125ecb5d119f..5161d130c7f8b 100644
>> --- a/drivers/phy/mediatek/Kconfig
>> +++ b/drivers/phy/mediatek/Kconfig
>> @@ -13,6 +13,18 @@ config PHY_MTK_PCIE
>>     callback for PCIe GEN3 port, it supports software efuse
>>     initialization.
>>   
>> +config PHY_MTK_XFI_TPHY
>> +tristate "MediaTek XFI T-PHY Driver"
>> +depends on ARCH_MEDIATEK || COMPILE_TEST
>> +depends on OF && OF_ADDRESS
>> +depends on HAS_IOMEM
>> +select GENERIC_PHY
>> +help
>> +  Say 'Y' here to add support for MediaTek XFI T-PHY driver.
>> +  The driver provides access to the Ethernet SerDes T-PHY supporting
>> +  1GE and 2.5GE modes via the LynxI PCS, and 5GE and 10GE modes
>> +  via the USXGMII PCS found in MediaTek SoCs with 10G Ethernet.
>> +
>>   config PHY_MTK_TPHY
>>   tristate "MediaTek T-PHY Driver"
>>   depends on ARCH_MEDIATEK || COMPILE_TEST
>> diff --git a/drivers/phy/mediatek/Makefile
>> b/drivers/phy/mediatek/Makefile
>> index c9a50395533eb..fa7217178e7f4 100644
>> --- a/drivers/phy/mediatek/Makefile
>> +++ b/drivers/phy/mediatek/Makefile
>> @@ -8,6 +8,7 @@ obj-$(CONFIG_PHY_MTK_PCIE)+= phy-mtk-pcie.o
>>   obj-$(CONFIG_PHY_MTK_TPHY)+= phy-mtk-tphy.o
>>   obj-$(CONFIG_PHY_MTK_UFS)+= phy-mtk-ufs.o
>>   obj-$(CONFIG_PHY_MTK_XSPHY)+= phy-mtk-xsphy.o
>> +obj-$(CONFIG_PHY_MTK_XFI_TPHY)+= phy-mtk-xfi-tphy.o
>>   
>>   phy-mtk-hdmi-drv-y:= phy-mtk-hdmi.o
>>   phy-mtk-hdmi-drv-y+= phy-mtk-hdmi-mt2701.o
>> diff --git a/drivers/phy/mediatek/phy-mtk-xfi-tphy.c
>> b/drivers/phy/mediatek/phy-mtk-xfi-tphy.c
>> new file mode 100644
>> index 0000000000000..d50e6320860e5
>> --- /dev/null
>> +++ b/drivers/phy/mediatek/phy-mtk-xfi-tphy.c
>> @@ -0,0 +1,392 @@
>> +// SPDX-License-Identifier: GPL-2.0-or-later
>> +/* MediaTek 10GE SerDes PHY driver
>> + *
>> + * Copyright (c) 2024 Daniel Golle <daniel@makrotopia.org>
>> + *                    Bc-bocun Chen <bc-bocun.chen@mediatek.com>
>> + * based on mtk_usxgmii.c found in MediaTek's SDK released under
>> GPL-2.0
>> + * Copyright (c) 2022 MediaTek Inc.
>> + * Author: Henry Yen <henry.yen@mediatek.com>
>> + */
>> +
>> +#include <linux/module.h>
>> +#include <linux/device.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/of.h>
>> +#include <linux/io.h>
>> +#include <linux/clk.h>
>> +#include <linux/reset.h>
>> +#include <linux/phy.h>
>> +#include <linux/phy/phy.h>
>> +
>> +#define MTK_XFI_TPHY_NUM_CLOCKS2
>> +
>> +#define REG_DIG_GLB_700x0070
>> +#define  XTP_PCS_RX_EQ_IN_PROGRESS(x)FIELD_PREP(GENMASK(25, 24),
>> (x))
>> +#define  XTP_PCS_MODE_MASKGENMASK(17, 16)
>> +#define  XTP_PCS_MODE(x)FIELD_PREP(GENMASK(17, 16), (x))
>> +#define  XTP_PCS_RST_BBIT(15)
>> +#define  XTP_FRC_PCS_RST_BBIT(14)
>> +#define  XTP_PCS_PWD_SYNC_MASKGENMASK(13, 12)
>> +#define  XTP_PCS_PWD_SYNC(x)FIELD_PREP(XTP_PCS_PWD_SYNC_MASK, (x))
>> +#define  XTP_PCS_PWD_ASYNC_MASKGENMASK(11, 10)
>> +#define  XTP_PCS_PWD_ASYNC(x)FIELD_PREP(XTP_PCS_PWD_ASYNC_MASK, (x))
>> +#define  XTP_FRC_PCS_PWD_ASYNCBIT(8)
>> +#define  XTP_PCS_UPDTBIT(4)
>> +#define  XTP_PCS_IN_FR_RGBIT(0)
>> +
>> +#define REG_DIG_GLB_F40x00f4
>> +#define  XFI_DPHY_PCS_SELBIT(0)
>> +#define   XFI_DPHY_PCS_SEL_SGMIIFIELD_PREP(XFI_DPHY_PCS_SEL, 1)
>> +#define   XFI_DPHY_PCS_SEL_USXGMIIFIELD_PREP(XFI_DPHY_PCS_SEL, 0)
>> +#define  XFI_DPHY_AD_SGDT_FRC_ENBIT(5)
>> +
>> +#define REG_DIG_LN_TRX_400x3040
>> +#define  XTP_LN_FRC_TX_DATA_ENBIT(29)
>> +#define  XTP_LN_TX_DATA_ENBIT(28)
>> +
>> +#define REG_DIG_LN_TRX_B00x30b0
>> +#define  XTP_LN_FRC_TX_MACCK_ENBIT(5)
>> +#define  XTP_LN_TX_MACCK_ENBIT(4)
>> +
>> +#define REG_ANA_GLB_D00x90d0
>> +#define  XTP_GLB_USXGMII_SEL_MASKGENMASK(3, 1)
>> +#define  XTP_GLB_USXGMII_SEL(x)FIELD_PREP(GENMASK(3, 1), (x))
>> +#define  XTP_GLB_USXGMII_ENBIT(0)
>> +
>> +struct mtk_xfi_tphy {
>> +void __iomem*base;
>> +struct device*dev;
>> +struct reset_control*reset;
>> +struct clk_bulk_dataclocks[MTK_XFI_TPHY_NUM_CLOCKS];
>> +boolda_war;
>> +};
>> +
>> +static void mtk_xfi_tphy_write(struct mtk_xfi_tphy *xfi_tphy, u16
>> reg,
>> +       u32 value)
>> +{
>> +iowrite32(value, xfi_tphy->base + reg);
>> +}
>> +
>> +static void mtk_xfi_tphy_rmw(struct mtk_xfi_tphy *xfi_tphy, u16 reg,
>> +     u32 clr, u32 set)
>> +{
>> +u32 val;
>> +
>> +val = ioread32(xfi_tphy->base + reg);
>> +val &= ~clr;
>> +val |= set;
>> +iowrite32(val, xfi_tphy->base + reg);
>> +}
>> +
>> +static void mtk_xfi_tphy_set(struct mtk_xfi_tphy *xfi_tphy, u16 reg,
>> +     u32 set)
>> +{
>> +mtk_xfi_tphy_rmw(xfi_tphy, reg, 0, set);
>> +}
>> +
>> +static void mtk_xfi_tphy_clear(struct mtk_xfi_tphy *xfi_tphy, u16
>> reg,
>> +       u32 clr)
>> +{
>> +mtk_xfi_tphy_rmw(xfi_tphy, reg, clr, 0);
>> +}
> 
> Helpers defined in phy-mtk-io.h can be used instead?
> 
>> +
>> +static void mtk_xfi_tphy_setup(struct mtk_xfi_tphy *xfi_tphy,
>> +       phy_interface_t interface)
>> +{
>> +bool is_2p5g = (interface == PHY_INTERFACE_MODE_2500BASEX);
>> +bool is_1g = (interface == PHY_INTERFACE_MODE_1000BASEX ||
>> +      interface == PHY_INTERFACE_MODE_SGMII);
>> +bool is_10g = (interface == PHY_INTERFACE_MODE_10GBASER ||
>> +       interface == PHY_INTERFACE_MODE_USXGMII);
>> +bool is_5g = (interface == PHY_INTERFACE_MODE_5GBASER);
>> +bool is_xgmii = (is_10g || is_5g);
>> +
>> +dev_dbg(xfi_tphy->dev, "setting up for mode %s\n",
>> phy_modes(interface));
>> +
>> +/* Setup PLL setting */
>> +mtk_xfi_tphy_rmw(xfi_tphy, 0x9024, 0x100000, is_10g ? 0x0 :
>> 0x100000);
>> +mtk_xfi_tphy_rmw(xfi_tphy, 0x2020, 0x202000, is_5g ? 0x202000 :
>> 0x0);
>> +mtk_xfi_tphy_rmw(xfi_tphy, 0x2030, 0x500, is_1g ? 0x0 : 0x500);
>> +mtk_xfi_tphy_rmw(xfi_tphy, 0x2034, 0xa00, is_1g ? 0x0 : 0xa00);
>> +mtk_xfi_tphy_rmw(xfi_tphy, 0x2040, 0x340000, is_1g ? 0x200000 :
>> +     0x140000);
>> +
>> +/* Setup RXFE BW setting */
>> +mtk_xfi_tphy_rmw(xfi_tphy, 0x50f0, 0xc10, is_1g ? 0x410 :
>> +  is_5g ? 0x800 : 0x400);
>> +mtk_xfi_tphy_rmw(xfi_tphy, 0x50e0, 0x4000, is_5g ? 0x0 : 0x4000);
>> +
>> +/* Setup RX CDR setting */
>> +mtk_xfi_tphy_rmw(xfi_tphy, 0x506c, 0x30000, is_5g ? 0x0 : 0x30000);
>> +mtk_xfi_tphy_rmw(xfi_tphy, 0x5070, 0x670000, is_5g ? 0x620000 :
>> 0x50000);
>> +mtk_xfi_tphy_rmw(xfi_tphy, 0x5074, 0x180000, is_5g ? 0x180000 :
>> 0x0);
>> +mtk_xfi_tphy_rmw(xfi_tphy, 0x5078, 0xf000400, is_5g ? 0x8000000 :
>> +      0x7000400);
>> +mtk_xfi_tphy_rmw(xfi_tphy, 0x507c, 0x5000500, is_5g ? 0x4000400 :
>> +      0x1000100);
>> +mtk_xfi_tphy_rmw(xfi_tphy, 0x5080, 0x1410, is_1g ? 0x400 :
>> +   is_5g ? 0x1010 : 0x0);
>> +mtk_xfi_tphy_rmw(xfi_tphy, 0x5084, 0x30300, is_1g ? 0x30300 :
>> +    is_5g ? 0x30100 :
>> +    0x100);
>> +mtk_xfi_tphy_rmw(xfi_tphy, 0x5088, 0x60200, is_1g ? 0x20200 :
>> + is_5g ? 0x40000 :
>> + 0x20000);
>> +
>> +/* Setting RXFE adaptation range setting */
>> +mtk_xfi_tphy_rmw(xfi_tphy, 0x50e4, 0xc0000, is_5g ? 0x0 : 0xc0000);
>> +mtk_xfi_tphy_rmw(xfi_tphy, 0x50e8, 0x40000, is_5g ? 0x0 : 0x40000);
>> +mtk_xfi_tphy_rmw(xfi_tphy, 0x50ec, 0xa00, is_1g ? 0x200 : 0x800);
>> +mtk_xfi_tphy_rmw(xfi_tphy, 0x50a8, 0xee0000, is_5g ? 0x800000 :
>> +     0x6e0000);
>> +mtk_xfi_tphy_rmw(xfi_tphy, 0x6004, 0x190000, is_5g ? 0x0 :
>> 0x190000);
>> +if (is_10g)
>> +mtk_xfi_tphy_write(xfi_tphy, 0x00f8, 0x01423342);
>> +else if (is_5g)
>> +mtk_xfi_tphy_write(xfi_tphy, 0x00f8, 0x00a132a1);
>> +else if (is_2p5g)
>> +mtk_xfi_tphy_write(xfi_tphy, 0x00f8, 0x009c329c);
>> +else
>> +mtk_xfi_tphy_write(xfi_tphy, 0x00f8, 0x00fa32fa);
> Still have many magic number.
> 

There's lack of documentation, that's why Daniel has all those magic numbers there.

If you can help unrolling some definitions that'd be really appreciated, as that
would result in a cleaner driver.

Cheers,
Angelo
  

Patch

diff --git a/MAINTAINERS b/MAINTAINERS
index 52769631bdb1a..52e4192470bd9 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -13715,6 +13715,7 @@  L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/phy/mediatek-ge-soc.c
 F:	drivers/net/phy/mediatek-ge.c
+F:	drivers/phy/mediatek/phy-mtk-xfi-tphy.c
 
 MEDIATEK I2C CONTROLLER DRIVER
 M:	Qii Wang <qii.wang@mediatek.com>
diff --git a/drivers/phy/mediatek/Kconfig b/drivers/phy/mediatek/Kconfig
index 3125ecb5d119f..5161d130c7f8b 100644
--- a/drivers/phy/mediatek/Kconfig
+++ b/drivers/phy/mediatek/Kconfig
@@ -13,6 +13,18 @@  config PHY_MTK_PCIE
 	  callback for PCIe GEN3 port, it supports software efuse
 	  initialization.
 
+config PHY_MTK_XFI_TPHY
+	tristate "MediaTek XFI T-PHY Driver"
+	depends on ARCH_MEDIATEK || COMPILE_TEST
+	depends on OF && OF_ADDRESS
+	depends on HAS_IOMEM
+	select GENERIC_PHY
+	help
+	  Say 'Y' here to add support for MediaTek XFI T-PHY driver.
+	  The driver provides access to the Ethernet SerDes T-PHY supporting
+	  1GE and 2.5GE modes via the LynxI PCS, and 5GE and 10GE modes
+	  via the USXGMII PCS found in MediaTek SoCs with 10G Ethernet.
+
 config PHY_MTK_TPHY
 	tristate "MediaTek T-PHY Driver"
 	depends on ARCH_MEDIATEK || COMPILE_TEST
diff --git a/drivers/phy/mediatek/Makefile b/drivers/phy/mediatek/Makefile
index c9a50395533eb..fa7217178e7f4 100644
--- a/drivers/phy/mediatek/Makefile
+++ b/drivers/phy/mediatek/Makefile
@@ -8,6 +8,7 @@  obj-$(CONFIG_PHY_MTK_PCIE)		+= phy-mtk-pcie.o
 obj-$(CONFIG_PHY_MTK_TPHY)		+= phy-mtk-tphy.o
 obj-$(CONFIG_PHY_MTK_UFS)		+= phy-mtk-ufs.o
 obj-$(CONFIG_PHY_MTK_XSPHY)		+= phy-mtk-xsphy.o
+obj-$(CONFIG_PHY_MTK_XFI_TPHY)		+= phy-mtk-xfi-tphy.o
 
 phy-mtk-hdmi-drv-y			:= phy-mtk-hdmi.o
 phy-mtk-hdmi-drv-y			+= phy-mtk-hdmi-mt2701.o
diff --git a/drivers/phy/mediatek/phy-mtk-xfi-tphy.c b/drivers/phy/mediatek/phy-mtk-xfi-tphy.c
new file mode 100644
index 0000000000000..d50e6320860e5
--- /dev/null
+++ b/drivers/phy/mediatek/phy-mtk-xfi-tphy.c
@@ -0,0 +1,392 @@ 
+// SPDX-License-Identifier: GPL-2.0-or-later
+/* MediaTek 10GE SerDes PHY driver
+ *
+ * Copyright (c) 2024 Daniel Golle <daniel@makrotopia.org>
+ *                    Bc-bocun Chen <bc-bocun.chen@mediatek.com>
+ * based on mtk_usxgmii.c found in MediaTek's SDK released under GPL-2.0
+ * Copyright (c) 2022 MediaTek Inc.
+ * Author: Henry Yen <henry.yen@mediatek.com>
+ */
+
+#include <linux/module.h>
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/io.h>
+#include <linux/clk.h>
+#include <linux/reset.h>
+#include <linux/phy.h>
+#include <linux/phy/phy.h>
+
+#define MTK_XFI_TPHY_NUM_CLOCKS		2
+
+#define REG_DIG_GLB_70			0x0070
+#define  XTP_PCS_RX_EQ_IN_PROGRESS(x)	FIELD_PREP(GENMASK(25, 24), (x))
+#define  XTP_PCS_MODE_MASK		GENMASK(17, 16)
+#define  XTP_PCS_MODE(x)		FIELD_PREP(GENMASK(17, 16), (x))
+#define  XTP_PCS_RST_B			BIT(15)
+#define  XTP_FRC_PCS_RST_B		BIT(14)
+#define  XTP_PCS_PWD_SYNC_MASK		GENMASK(13, 12)
+#define  XTP_PCS_PWD_SYNC(x)		FIELD_PREP(XTP_PCS_PWD_SYNC_MASK, (x))
+#define  XTP_PCS_PWD_ASYNC_MASK		GENMASK(11, 10)
+#define  XTP_PCS_PWD_ASYNC(x)		FIELD_PREP(XTP_PCS_PWD_ASYNC_MASK, (x))
+#define  XTP_FRC_PCS_PWD_ASYNC		BIT(8)
+#define  XTP_PCS_UPDT			BIT(4)
+#define  XTP_PCS_IN_FR_RG		BIT(0)
+
+#define REG_DIG_GLB_F4			0x00f4
+#define  XFI_DPHY_PCS_SEL		BIT(0)
+#define   XFI_DPHY_PCS_SEL_SGMII	FIELD_PREP(XFI_DPHY_PCS_SEL, 1)
+#define   XFI_DPHY_PCS_SEL_USXGMII	FIELD_PREP(XFI_DPHY_PCS_SEL, 0)
+#define  XFI_DPHY_AD_SGDT_FRC_EN	BIT(5)
+
+#define REG_DIG_LN_TRX_40		0x3040
+#define  XTP_LN_FRC_TX_DATA_EN		BIT(29)
+#define  XTP_LN_TX_DATA_EN		BIT(28)
+
+#define REG_DIG_LN_TRX_B0		0x30b0
+#define  XTP_LN_FRC_TX_MACCK_EN		BIT(5)
+#define  XTP_LN_TX_MACCK_EN		BIT(4)
+
+#define REG_ANA_GLB_D0			0x90d0
+#define  XTP_GLB_USXGMII_SEL_MASK	GENMASK(3, 1)
+#define  XTP_GLB_USXGMII_SEL(x)		FIELD_PREP(GENMASK(3, 1), (x))
+#define  XTP_GLB_USXGMII_EN		BIT(0)
+
+struct mtk_xfi_tphy {
+	void __iomem		*base;
+	struct device		*dev;
+	struct reset_control	*reset;
+	struct clk_bulk_data	clocks[MTK_XFI_TPHY_NUM_CLOCKS];
+	bool			da_war;
+};
+
+static void mtk_xfi_tphy_write(struct mtk_xfi_tphy *xfi_tphy, u16 reg,
+			       u32 value)
+{
+	iowrite32(value, xfi_tphy->base + reg);
+}
+
+static void mtk_xfi_tphy_rmw(struct mtk_xfi_tphy *xfi_tphy, u16 reg,
+			     u32 clr, u32 set)
+{
+	u32 val;
+
+	val = ioread32(xfi_tphy->base + reg);
+	val &= ~clr;
+	val |= set;
+	iowrite32(val, xfi_tphy->base + reg);
+}
+
+static void mtk_xfi_tphy_set(struct mtk_xfi_tphy *xfi_tphy, u16 reg,
+			     u32 set)
+{
+	mtk_xfi_tphy_rmw(xfi_tphy, reg, 0, set);
+}
+
+static void mtk_xfi_tphy_clear(struct mtk_xfi_tphy *xfi_tphy, u16 reg,
+			       u32 clr)
+{
+	mtk_xfi_tphy_rmw(xfi_tphy, reg, clr, 0);
+}
+
+static void mtk_xfi_tphy_setup(struct mtk_xfi_tphy *xfi_tphy,
+			       phy_interface_t interface)
+{
+	bool is_2p5g = (interface == PHY_INTERFACE_MODE_2500BASEX);
+	bool is_1g = (interface == PHY_INTERFACE_MODE_1000BASEX ||
+		      interface == PHY_INTERFACE_MODE_SGMII);
+	bool is_10g = (interface == PHY_INTERFACE_MODE_10GBASER ||
+		       interface == PHY_INTERFACE_MODE_USXGMII);
+	bool is_5g = (interface == PHY_INTERFACE_MODE_5GBASER);
+	bool is_xgmii = (is_10g || is_5g);
+
+	dev_dbg(xfi_tphy->dev, "setting up for mode %s\n", phy_modes(interface));
+
+	/* Setup PLL setting */
+	mtk_xfi_tphy_rmw(xfi_tphy, 0x9024, 0x100000, is_10g ? 0x0 : 0x100000);
+	mtk_xfi_tphy_rmw(xfi_tphy, 0x2020, 0x202000, is_5g ? 0x202000 : 0x0);
+	mtk_xfi_tphy_rmw(xfi_tphy, 0x2030, 0x500, is_1g ? 0x0 : 0x500);
+	mtk_xfi_tphy_rmw(xfi_tphy, 0x2034, 0xa00, is_1g ? 0x0 : 0xa00);
+	mtk_xfi_tphy_rmw(xfi_tphy, 0x2040, 0x340000, is_1g ? 0x200000 :
+							     0x140000);
+
+	/* Setup RXFE BW setting */
+	mtk_xfi_tphy_rmw(xfi_tphy, 0x50f0, 0xc10, is_1g ? 0x410 :
+							  is_5g ? 0x800 : 0x400);
+	mtk_xfi_tphy_rmw(xfi_tphy, 0x50e0, 0x4000, is_5g ? 0x0 : 0x4000);
+
+	/* Setup RX CDR setting */
+	mtk_xfi_tphy_rmw(xfi_tphy, 0x506c, 0x30000, is_5g ? 0x0 : 0x30000);
+	mtk_xfi_tphy_rmw(xfi_tphy, 0x5070, 0x670000, is_5g ? 0x620000 : 0x50000);
+	mtk_xfi_tphy_rmw(xfi_tphy, 0x5074, 0x180000, is_5g ? 0x180000 : 0x0);
+	mtk_xfi_tphy_rmw(xfi_tphy, 0x5078, 0xf000400, is_5g ? 0x8000000 :
+							      0x7000400);
+	mtk_xfi_tphy_rmw(xfi_tphy, 0x507c, 0x5000500, is_5g ? 0x4000400 :
+							      0x1000100);
+	mtk_xfi_tphy_rmw(xfi_tphy, 0x5080, 0x1410, is_1g ? 0x400 :
+							   is_5g ? 0x1010 : 0x0);
+	mtk_xfi_tphy_rmw(xfi_tphy, 0x5084, 0x30300, is_1g ? 0x30300 :
+							    is_5g ? 0x30100 :
+								    0x100);
+	mtk_xfi_tphy_rmw(xfi_tphy, 0x5088, 0x60200, is_1g ? 0x20200 :
+							 is_5g ? 0x40000 :
+								 0x20000);
+
+	/* Setting RXFE adaptation range setting */
+	mtk_xfi_tphy_rmw(xfi_tphy, 0x50e4, 0xc0000, is_5g ? 0x0 : 0xc0000);
+	mtk_xfi_tphy_rmw(xfi_tphy, 0x50e8, 0x40000, is_5g ? 0x0 : 0x40000);
+	mtk_xfi_tphy_rmw(xfi_tphy, 0x50ec, 0xa00, is_1g ? 0x200 : 0x800);
+	mtk_xfi_tphy_rmw(xfi_tphy, 0x50a8, 0xee0000, is_5g ? 0x800000 :
+							     0x6e0000);
+	mtk_xfi_tphy_rmw(xfi_tphy, 0x6004, 0x190000, is_5g ? 0x0 : 0x190000);
+	if (is_10g)
+		mtk_xfi_tphy_write(xfi_tphy, 0x00f8, 0x01423342);
+	else if (is_5g)
+		mtk_xfi_tphy_write(xfi_tphy, 0x00f8, 0x00a132a1);
+	else if (is_2p5g)
+		mtk_xfi_tphy_write(xfi_tphy, 0x00f8, 0x009c329c);
+	else
+		mtk_xfi_tphy_write(xfi_tphy, 0x00f8, 0x00fa32fa);
+
+	/* Force SGDT_OUT off and select PCS */
+	mtk_xfi_tphy_rmw(xfi_tphy, REG_DIG_GLB_F4,
+			 XFI_DPHY_AD_SGDT_FRC_EN | XFI_DPHY_PCS_SEL,
+			 XFI_DPHY_AD_SGDT_FRC_EN |
+			 (is_xgmii ? XFI_DPHY_PCS_SEL_USXGMII :
+				     XFI_DPHY_PCS_SEL_SGMII));
+
+
+	/* Force GLB_CKDET_OUT */
+	mtk_xfi_tphy_set(xfi_tphy, 0x0030, 0xc00);
+
+	/* Force AEQ on */
+	mtk_xfi_tphy_write(xfi_tphy, REG_DIG_GLB_70,
+			   XTP_PCS_RX_EQ_IN_PROGRESS(2) |
+			   XTP_PCS_PWD_SYNC(2) |
+			   XTP_PCS_PWD_ASYNC(2));
+
+	usleep_range(1, 5);
+
+	/* Setup TX DA default value */
+	mtk_xfi_tphy_rmw(xfi_tphy, 0x30b0, 0x30, 0x20);
+	mtk_xfi_tphy_write(xfi_tphy, 0x3028, 0x00008a01);
+	mtk_xfi_tphy_write(xfi_tphy, 0x302c, 0x0000a884);
+	mtk_xfi_tphy_write(xfi_tphy, 0x3024, 0x00083002);
+
+	/* Setup RG default value */
+	if (is_xgmii) {
+		mtk_xfi_tphy_write(xfi_tphy, 0x3010, 0x00022220);
+		mtk_xfi_tphy_write(xfi_tphy, 0x5064, 0x0f020a01);
+		mtk_xfi_tphy_write(xfi_tphy, 0x50b4, 0x06100600);
+		if (interface == PHY_INTERFACE_MODE_USXGMII)
+			mtk_xfi_tphy_write(xfi_tphy, 0x3048, 0x40704000);
+		else
+			mtk_xfi_tphy_write(xfi_tphy, 0x3048, 0x47684100);
+	} else {
+		mtk_xfi_tphy_write(xfi_tphy, 0x3010, 0x00011110);
+		mtk_xfi_tphy_write(xfi_tphy, 0x3048, 0x40704000);
+	}
+
+	if (is_1g)
+		mtk_xfi_tphy_write(xfi_tphy, 0x3064, 0x0000c000);
+
+	/* Setup RX EQ initial value */
+	mtk_xfi_tphy_rmw(xfi_tphy, 0x3050, 0xa8000000,
+			 (interface != PHY_INTERFACE_MODE_10GBASER) ?
+			  0xa8000000 : 0x0);
+	mtk_xfi_tphy_rmw(xfi_tphy, 0x3054, 0xaa,
+			 (interface != PHY_INTERFACE_MODE_10GBASER) ?
+			  0xaa : 0x0);
+
+	if (is_xgmii)
+		mtk_xfi_tphy_write(xfi_tphy, 0x306c, 0x00000f00);
+	else if (is_2p5g)
+		mtk_xfi_tphy_write(xfi_tphy, 0x306c, 0x22000f00);
+	else
+		mtk_xfi_tphy_write(xfi_tphy, 0x306c, 0x20200f00);
+
+	if (interface == PHY_INTERFACE_MODE_10GBASER && xfi_tphy->da_war)
+		mtk_xfi_tphy_rmw(xfi_tphy, 0xa008, 0x10000, 0x10000);
+
+	mtk_xfi_tphy_rmw(xfi_tphy, 0xa060, 0x50000, is_xgmii ? 0x40000 :
+							       0x50000);
+
+	/* Setup PHYA speed */
+	mtk_xfi_tphy_rmw(xfi_tphy, REG_ANA_GLB_D0,
+			 XTP_GLB_USXGMII_SEL_MASK | XTP_GLB_USXGMII_EN,
+			 is_10g ?  XTP_GLB_USXGMII_SEL(0) :
+			 is_5g ?   XTP_GLB_USXGMII_SEL(1) :
+			 is_2p5g ? XTP_GLB_USXGMII_SEL(2) :
+				   XTP_GLB_USXGMII_SEL(3));
+	mtk_xfi_tphy_set(xfi_tphy, REG_ANA_GLB_D0, XTP_GLB_USXGMII_EN);
+
+	/* Release reset */
+	mtk_xfi_tphy_set(xfi_tphy, REG_DIG_GLB_70,
+			 XTP_PCS_RST_B | XTP_FRC_PCS_RST_B);
+	usleep_range(150, 500);
+
+	/* Switch to P0 */
+	mtk_xfi_tphy_rmw(xfi_tphy, REG_DIG_GLB_70,
+			 XTP_PCS_PWD_SYNC_MASK |
+			 XTP_PCS_PWD_ASYNC_MASK,
+			 XTP_FRC_PCS_PWD_ASYNC |
+			 XTP_PCS_UPDT | XTP_PCS_IN_FR_RG);
+	usleep_range(1, 5);
+
+	mtk_xfi_tphy_clear(xfi_tphy, REG_DIG_GLB_70, XTP_PCS_UPDT);
+	usleep_range(15, 50);
+
+	if (is_xgmii) {
+		/* Switch to Gen3 */
+		mtk_xfi_tphy_rmw(xfi_tphy, REG_DIG_GLB_70,
+				 XTP_PCS_MODE_MASK | XTP_PCS_UPDT,
+				 XTP_PCS_MODE(2) | XTP_PCS_UPDT);
+	} else {
+		/* Switch to Gen2 */
+		mtk_xfi_tphy_rmw(xfi_tphy, REG_DIG_GLB_70,
+				 XTP_PCS_MODE_MASK | XTP_PCS_UPDT,
+				 XTP_PCS_MODE(1) | XTP_PCS_UPDT);
+	}
+	usleep_range(1, 5);
+
+	mtk_xfi_tphy_clear(xfi_tphy, REG_DIG_GLB_70, XTP_PCS_UPDT);
+
+	usleep_range(100, 500);
+
+	/* Enable MAC CK */
+	mtk_xfi_tphy_set(xfi_tphy, REG_DIG_LN_TRX_B0, XTP_LN_TX_MACCK_EN);
+	mtk_xfi_tphy_clear(xfi_tphy, REG_DIG_GLB_F4, XFI_DPHY_AD_SGDT_FRC_EN);
+
+	/* Enable TX data */
+	mtk_xfi_tphy_set(xfi_tphy, REG_DIG_LN_TRX_40,
+			 XTP_LN_FRC_TX_DATA_EN | XTP_LN_TX_DATA_EN);
+	usleep_range(400, 1000);
+}
+
+static int mtk_xfi_tphy_set_mode(struct phy *phy, enum phy_mode mode, int
+				 submode)
+{
+	struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy);
+
+	if (mode != PHY_MODE_ETHERNET)
+		return -EINVAL;
+
+	switch (submode) {
+	case PHY_INTERFACE_MODE_1000BASEX:
+	case PHY_INTERFACE_MODE_2500BASEX:
+	case PHY_INTERFACE_MODE_SGMII:
+	case PHY_INTERFACE_MODE_5GBASER:
+	case PHY_INTERFACE_MODE_10GBASER:
+	case PHY_INTERFACE_MODE_USXGMII:
+		mtk_xfi_tphy_setup(xfi_tphy, submode);
+		return 0;
+	default:
+		return -EINVAL;
+	}
+}
+
+static int mtk_xfi_tphy_reset(struct phy *phy)
+{
+	struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy);
+
+	reset_control_assert(xfi_tphy->reset);
+	usleep_range(100, 500);
+	reset_control_deassert(xfi_tphy->reset);
+	usleep_range(1, 10);
+
+	return 0;
+}
+
+static int mtk_xfi_tphy_power_on(struct phy *phy)
+{
+	struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy);
+
+	return clk_bulk_prepare_enable(MTK_XFI_TPHY_NUM_CLOCKS, xfi_tphy->clocks);
+}
+
+static int mtk_xfi_tphy_power_off(struct phy *phy)
+{
+	struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy);
+
+	clk_bulk_disable_unprepare(MTK_XFI_TPHY_NUM_CLOCKS, xfi_tphy->clocks);
+
+	return 0;
+}
+
+static const struct phy_ops mtk_xfi_tphy_ops = {
+	.power_on	= mtk_xfi_tphy_power_on,
+	.power_off	= mtk_xfi_tphy_power_off,
+	.set_mode	= mtk_xfi_tphy_set_mode,
+	.reset		= mtk_xfi_tphy_reset,
+	.owner		= THIS_MODULE,
+};
+
+static int mtk_xfi_tphy_probe(struct platform_device *pdev)
+{
+	struct device_node *np = pdev->dev.of_node;
+	struct phy_provider *phy_provider;
+	struct mtk_xfi_tphy *xfi_tphy;
+	struct phy *phy;
+
+	if (!np)
+		return -ENODEV;
+
+	xfi_tphy = devm_kzalloc(&pdev->dev, sizeof(*xfi_tphy), GFP_KERNEL);
+	if (!xfi_tphy)
+		return -ENOMEM;
+
+	xfi_tphy->base = devm_of_iomap(&pdev->dev, np, 0, NULL);
+	if (!xfi_tphy->base)
+		return -EIO;
+
+	xfi_tphy->dev = &pdev->dev;
+
+	xfi_tphy->clocks[0].id = "topxtal";
+	xfi_tphy->clocks[0].clk = devm_clk_get(&pdev->dev, xfi_tphy->clocks[0].id);
+	if (IS_ERR(xfi_tphy->clocks[0].clk))
+		return PTR_ERR(xfi_tphy->clocks[0].clk);
+
+	xfi_tphy->clocks[1].id = "xfipll";
+	xfi_tphy->clocks[1].clk = devm_clk_get(&pdev->dev, xfi_tphy->clocks[1].id);
+	if (IS_ERR(xfi_tphy->clocks[1].clk))
+		return PTR_ERR(xfi_tphy->clocks[1].clk);
+
+	xfi_tphy->reset = devm_reset_control_get_exclusive(&pdev->dev, NULL);
+	if (IS_ERR(xfi_tphy->reset))
+		return PTR_ERR(xfi_tphy->reset);
+
+	xfi_tphy->da_war = of_property_read_bool(np,
+						 "mediatek,usxgmii-performance-errata");
+
+	phy = devm_phy_create(&pdev->dev, NULL, &mtk_xfi_tphy_ops);
+	if (IS_ERR(phy))
+		return PTR_ERR(phy);
+
+	phy_set_drvdata(phy, xfi_tphy);
+
+	phy_provider = devm_of_phy_provider_register(&pdev->dev,
+						     of_phy_simple_xlate);
+
+	return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct of_device_id mtk_xfi_tphy_match[] = {
+	{ .compatible = "mediatek,mt7988-xfi-tphy", },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, mtk_xfi_tphy_match);
+
+static struct platform_driver mtk_xfi_tphy_driver = {
+	.probe = mtk_xfi_tphy_probe,
+	.driver = {
+		.name = "mtk-xfi-tphy",
+		.of_match_table = mtk_xfi_tphy_match,
+	},
+};
+module_platform_driver(mtk_xfi_tphy_driver);
+
+MODULE_DESCRIPTION("MediaTek XFI T-PHY driver");
+MODULE_AUTHOR("Daniel Golle <daniel@makrotopia.org>");
+MODULE_AUTHOR("Bc-bocun Chen <bc-bocun.chen@mediatek.com>");
+MODULE_LICENSE("GPL");