[v5,2/2] mtd: rawnand: rockchip: Align hwecc vs. raw page helper layouts
Commit Message
Currently, read/write_page_hwecc() and read/write_page_raw() are not
aligned: there is a mismatch in the OOB bytes which are not
read/written at the same offset in both cases (raw vs. hwecc).
This is a real problem when relying on the presence of the Page
Addresses (PA) when using the NAND chip as a boot device, as the
BootROM expects additional data in the OOB area at specific locations.
Rockchip boot blocks are written per 4 x 512 byte sectors per page.
Each page with boot blocks must have a page address (PA) pointer in OOB
to the next page. Pages are written in a pattern depending on the NAND chip ID.
Generate boot block page address and pattern for hwecc in user space
and copy PA data to/from the already reserved last 4 bytes before ECC
in the chip->oob_poi data layout.
Align the different helpers. This change breaks existing jffs2 users.
Fixes: 058e0e847d54 ("mtd: rawnand: rockchip: NFC driver for RK3308, RK2928 and others")
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
---
Changed V5:
Reword
Changed V4:
Reduce subject size
Add 'Fixes:' tag
Fix abbreviation
Reword
Changed V3:
Change prefixes
Reword
---
.../mtd/nand/raw/rockchip-nand-controller.c | 34 ++++++++++++-------
1 file changed, 21 insertions(+), 13 deletions(-)
--
2.30.2
Comments
On Fri, 2023-07-14 at 15:21:21 UTC, Johan Jonker wrote:
> Currently, read/write_page_hwecc() and read/write_page_raw() are not
> aligned: there is a mismatch in the OOB bytes which are not
> read/written at the same offset in both cases (raw vs. hwecc).
>
> This is a real problem when relying on the presence of the Page
> Addresses (PA) when using the NAND chip as a boot device, as the
> BootROM expects additional data in the OOB area at specific locations.
>
> Rockchip boot blocks are written per 4 x 512 byte sectors per page.
> Each page with boot blocks must have a page address (PA) pointer in OOB
> to the next page. Pages are written in a pattern depending on the NAND chip ID.
>
> Generate boot block page address and pattern for hwecc in user space
> and copy PA data to/from the already reserved last 4 bytes before ECC
> in the chip->oob_poi data layout.
>
> Align the different helpers. This change breaks existing jffs2 users.
>
> Fixes: 058e0e847d54 ("mtd: rawnand: rockchip: NFC driver for RK3308, RK2928 and others")
> Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Applied to https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git mtd/fixes, thanks.
Miquel
@@ -598,7 +598,7 @@ static int rk_nfc_write_page_hwecc(struct nand_chip *chip, const u8 *buf,
int pages_per_blk = mtd->erasesize / mtd->writesize;
int ret = 0, i, boot_rom_mode = 0;
dma_addr_t dma_data, dma_oob;
- u32 reg;
+ u32 tmp;
u8 *oob;
nand_prog_page_begin_op(chip, page, 0, NULL, 0);
@@ -625,6 +625,13 @@ static int rk_nfc_write_page_hwecc(struct nand_chip *chip, const u8 *buf,
*
* 0xFF 0xFF 0xFF 0xFF | BBM OOB1 OOB2 OOB3 | ...
*
+ * The code here just swaps the first 4 bytes with the last
+ * 4 bytes without losing any data.
+ *
+ * The chip->oob_poi data layout:
+ *
+ * BBM OOB1 OOB2 OOB3 |......| PA0 PA1 PA2 PA3
+ *
* Configure the ECC algorithm supported by the boot ROM.
*/
if ((page < (pages_per_blk * rknand->boot_blks)) &&
@@ -635,21 +642,17 @@ static int rk_nfc_write_page_hwecc(struct nand_chip *chip, const u8 *buf,
}
for (i = 0; i < ecc->steps; i++) {
- if (!i) {
- reg = 0xFFFFFFFF;
- } else {
+ if (!i)
+ oob = chip->oob_poi + (ecc->steps - 1) * NFC_SYS_DATA_SIZE;
+ else
oob = chip->oob_poi + (i - 1) * NFC_SYS_DATA_SIZE;
- reg = oob[0] | oob[1] << 8 | oob[2] << 16 |
- oob[3] << 24;
- }
- if (!i && boot_rom_mode)
- reg = (page & (pages_per_blk - 1)) * 4;
+ tmp = oob[0] | oob[1] << 8 | oob[2] << 16 | oob[3] << 24;
if (nfc->cfg->type == NFC_V9)
- nfc->oob_buf[i] = reg;
+ nfc->oob_buf[i] = tmp;
else
- nfc->oob_buf[i * (oob_step / 4)] = reg;
+ nfc->oob_buf[i * (oob_step / 4)] = tmp;
}
dma_data = dma_map_single(nfc->dev, (void *)nfc->page_buf,
@@ -812,12 +815,17 @@ static int rk_nfc_read_page_hwecc(struct nand_chip *chip, u8 *buf, int oob_on,
goto timeout_err;
}
- for (i = 1; i < ecc->steps; i++) {
- oob = chip->oob_poi + (i - 1) * NFC_SYS_DATA_SIZE;
+ for (i = 0; i < ecc->steps; i++) {
+ if (!i)
+ oob = chip->oob_poi + (ecc->steps - 1) * NFC_SYS_DATA_SIZE;
+ else
+ oob = chip->oob_poi + (i - 1) * NFC_SYS_DATA_SIZE;
+
if (nfc->cfg->type == NFC_V9)
tmp = nfc->oob_buf[i];
else
tmp = nfc->oob_buf[i * (oob_step / 4)];
+
*oob++ = (u8)tmp;
*oob++ = (u8)(tmp >> 8);
*oob++ = (u8)(tmp >> 16);