[V3,1/2] arm64: dts: ti: k3-am69-sk: Enable CAN interfaces for AM69 SK board
Commit Message
From: Dasnavis Sabiya <sabiya.d@ti.com>
AM69 SK board has several CAN bus interfaces on both MCU and MAIN domains.
This enables the CAN interfaces on MCU and MAIN domain.
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
---
arch/arm64/boot/dts/ti/k3-am69-sk.dts | 82 +++++++++++++++++++++++++++
1 file changed, 82 insertions(+)
@@ -330,6 +330,30 @@ csi_mux: mux-controller {
idle-state = <0>;
};
+ transceiver1: can-phy0 {
+ compatible = "ti,tcan1042";
+ #phy-cells = <0>;
+ max-bitrate = <5000000>;
+ };
+
+ transceiver2: can-phy1 {
+ compatible = "ti,tcan1042";
+ #phy-cells = <0>;
+ max-bitrate = <5000000>;
+ };
+
+ transceiver3: can-phy2 {
+ compatible = "ti,tcan1042";
+ #phy-cells = <0>;
+ max-bitrate = <5000000>;
+ };
+
+ transceiver4: can-phy3 {
+ compatible = "ti,tcan1042";
+ #phy-cells = <0>;
+ max-bitrate = <5000000>;
+ };
+
};
&main_pmx0 {
@@ -445,6 +469,21 @@ hdmi_hpd_pins_default: hdmi-hpd-default-pins {
J784S4_IOPAD(0x000, PIN_INPUT, 7) /* (AN35) EXTINTN.GPIO0_0 */
>;
};
+
+ main_mcan6_pins_default: main-mcan6-default-pins {
+ pinctrl-single,pins = <
+ J784S4_IOPAD(0x098, PIN_INPUT, 0) /* (AH36) MCAN6_RX */
+ J784S4_IOPAD(0x094, PIN_OUTPUT, 0) /* (AG35) MCAN6_TX */
+ >;
+ };
+
+ main_mcan7_pins_default: main-mcan7-default-pins {
+ pinctrl-single,pins = <
+ J784S4_IOPAD(0x0A0, PIN_INPUT, 0) /* (AD34) MCAN7_RX */
+ J784S4_IOPAD(0x09C, PIN_OUTPUT, 0) /* (AF35) MCAN7_TX */
+ >;
+ };
+
};
&wkup_pmx2 {
@@ -541,6 +580,21 @@ hdmi_pdn_pins_default: hdmi-pdn-default-pins {
J784S4_WKUP_IOPAD(0x090, PIN_INPUT, 7) /* (H37) WKUP_GPIO0_14 */
>;
};
+
+ mcu_mcan0_pins_default: mcu-mcan0-default-pins {
+ pinctrl-single,pins = <
+ J784S4_WKUP_IOPAD(0x054, PIN_INPUT, 0) /* (F38) MCU_MCAN0_RX */
+ J784S4_WKUP_IOPAD(0x050, PIN_OUTPUT, 0) /* (K33) MCU_MCAN0_TX */
+ >;
+ };
+
+ mcu_mcan1_pins_default: mcu-mcan1-default-pins {
+ pinctrl-single,pins = <
+ J784S4_WKUP_IOPAD(0x06c, PIN_INPUT, 0) /* (K36) WKUP_GPIO0_5.MCU_MCAN1_RX */
+ J784S4_WKUP_IOPAD(0x068, PIN_OUTPUT, 0)/* (H35) WKUP_GPIO0_4.MCU_MCAN1_TX */
+ >;
+ };
+
};
&wkup_pmx3 {
@@ -1040,3 +1094,31 @@ dp0_out: endpoint {
};
};
};
+
+&mcu_mcan0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcu_mcan0_pins_default>;
+ phys = <&transceiver1>;
+};
+
+&mcu_mcan1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcu_mcan1_pins_default>;
+ phys = <&transceiver2>;
+};
+
+&main_mcan6 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mcan6_pins_default>;
+ phys = <&transceiver3>;
+};
+
+&main_mcan7 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mcan7_pins_default>;
+ phys = <&transceiver4>;
+};