The dvs gpio was still using a legacy number passed from the
platform data. There are no in-tree users of the platform data
so just switch it to a gpio descriptor and obtain it in probe(),
the device tree users will work just as fine with this.
Drop the entirely unused enable_gpio from the platform data
as well. The device tree bindings mentions this but the driver
does not look for it and makes no use of it: it should probably
be implemented properly in a separate patch.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
drivers/regulator/max8973-regulator.c | 36 ++++++++++-------------------
include/linux/regulator/max8973-regulator.h | 6 -----
2 files changed, 12 insertions(+), 30 deletions(-)
@@ -20,9 +20,7 @@
#include <linux/regulator/machine.h>
#include <linux/regulator/max8973-regulator.h>
#include <linux/regulator/of_regulator.h>
-#include <linux/gpio.h>
#include <linux/gpio/consumer.h>
-#include <linux/of_gpio.h>
#include <linux/i2c.h>
#include <linux/slab.h>
#include <linux/regmap.h>
@@ -102,7 +100,7 @@ struct max8973_chip {
struct regulator_desc desc;
struct regmap *regmap;
bool enable_external_control;
- int dvs_gpio;
+ struct gpio_desc *dvs_gpiod;
int lru_index[MAX8973_MAX_VOUT_REG];
int curr_vout_val[MAX8973_MAX_VOUT_REG];
int curr_vout_reg;
@@ -184,7 +182,7 @@ static int max8973_dcdc_set_voltage_sel(struct regulator_dev *rdev,
* If gpios are available to select the VOUT register then least
* recently used register for new configuration.
*/
- if (gpio_is_valid(max->dvs_gpio))
+ if (max->dvs_gpiod)
found = find_voltage_set_register(max, vsel,
&vout_reg, &gpio_val);
@@ -201,8 +199,8 @@ static int max8973_dcdc_set_voltage_sel(struct regulator_dev *rdev,
}
/* Select proper VOUT register vio gpios */
- if (gpio_is_valid(max->dvs_gpio)) {
- gpio_set_value_cansleep(max->dvs_gpio, gpio_val & 0x1);
+ if (max->dvs_gpiod) {
+ gpiod_set_value_cansleep(max->dvs_gpiod, gpio_val & 0x1);
max->curr_gpio_val = gpio_val;
}
return 0;
@@ -531,7 +529,6 @@ static struct max8973_regulator_platform_data *max8973_parse_dt(
pdata->enable_ext_control = of_property_read_bool(np,
"maxim,externally-enable");
- pdata->dvs_gpio = of_get_named_gpio(np, "maxim,dvs-gpio", 0);
ret = of_property_read_u32(np, "maxim,dvs-default-state", &pval);
if (!ret)
@@ -612,13 +609,17 @@ static int max8973_probe(struct i2c_client *client)
return -EIO;
}
- if (pdata->dvs_gpio == -EPROBE_DEFER)
- return -EPROBE_DEFER;
-
max = devm_kzalloc(&client->dev, sizeof(*max), GFP_KERNEL);
if (!max)
return -ENOMEM;
+ max->dvs_gpiod = devm_gpiod_get_optional(&client->dev, "maxim,dvs",
+ (pdata->dvs_def_state) ? GPIOD_OUT_HIGH : GPIOD_OUT_LOW);
+ if (IS_ERR(max->dvs_gpiod))
+ return dev_err_probe(&client->dev, PTR_ERR(max->dvs_gpiod),
+ "failed to obtain dvs gpio\n");
+ gpiod_set_consumer_name(max->dvs_gpiod, "max8973-dvs");
+
max->regmap = devm_regmap_init_i2c(client, &max8973_regmap_config);
if (IS_ERR(max->regmap)) {
ret = PTR_ERR(max->regmap);
@@ -663,7 +664,6 @@ static int max8973_probe(struct i2c_client *client)
max->desc.ramp_delay_table = max8973_buck_ramp_table;
max->desc.n_ramp_values = ARRAY_SIZE(max8973_buck_ramp_table);
- max->dvs_gpio = (pdata->dvs_gpio) ? pdata->dvs_gpio : -EINVAL;
max->enable_external_control = pdata->enable_ext_control;
max->curr_gpio_val = pdata->dvs_def_state;
max->curr_vout_reg = MAX8973_VOUT + pdata->dvs_def_state;
@@ -671,21 +671,9 @@ static int max8973_probe(struct i2c_client *client)
max->lru_index[0] = max->curr_vout_reg;
- if (gpio_is_valid(max->dvs_gpio)) {
- int gpio_flags;
+ if (max->dvs_gpiod) {
int i;
- gpio_flags = (pdata->dvs_def_state) ?
- GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW;
- ret = devm_gpio_request_one(&client->dev, max->dvs_gpio,
- gpio_flags, "max8973-dvs");
- if (ret) {
- dev_err(&client->dev,
- "gpio_request for gpio %d failed, err = %d\n",
- max->dvs_gpio, ret);
- return ret;
- }
-
/*
* Initialize the lru index with vout_reg id
* The index 0 will be most recently used and
@@ -48,10 +48,6 @@
* control signal from EN input pin. If it is false then
* voltage output will be enabled/disabled through EN bit of
* device register.
- * @enable_gpio: Enable GPIO. If EN pin is controlled through GPIO from host
- * then GPIO number can be provided. If no GPIO controlled then
- * it should be -1.
- * @dvs_gpio: GPIO for dvs. It should be -1 if this is tied with fixed logic.
* @dvs_def_state: Default state of dvs. 1 if it is high else 0.
*/
struct max8973_regulator_platform_data {
@@ -59,8 +55,6 @@ struct max8973_regulator_platform_data {
unsigned long control_flags;
unsigned long junction_temp_warning;
bool enable_ext_control;
- int enable_gpio;
- int dvs_gpio;
unsigned dvs_def_state:1;
};