[V2] arm64: dts: ti: k3-am68-sk-som: Add support for OSPI flash
Commit Message
From: Sinthu Raja <sinthu.raja@ti.com>
AM68 SK has an OSPI NOR flash on its SOM connected to OSPI0 instance.
Enable support for the same. Also, describe the OSPI flash partition
information through the device tree, according to the offsets in the
bootloader.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
---
Changes in V2:
=============
1. Address review comments
a. remove pin E20, which is not connected.
V1: https://patchwork.kernel.org/project/linux-arm-kernel/patch/20240206092334.30307-1-sinthu.raja@ti.com/
arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi | 78 ++++++++++++++++++++++
1 file changed, 78 insertions(+)
@@ -130,6 +130,24 @@ rtos_ipc_memory_region: ipc-memories@a8000000 {
};
};
+&wkup_pmx0 {
+ mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default {
+ pinctrl-single,pins = <
+ J721S2_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (D19) MCU_OSPI0_CLK */
+ J721S2_WKUP_IOPAD(0x02c, PIN_OUTPUT, 0) /* (F15) MCU_OSPI0_CSn0 */
+ J721S2_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (C19) MCU_OSPI0_D0 */
+ J721S2_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (F16) MCU_OSPI0_D1 */
+ J721S2_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (G15) MCU_OSPI0_D2 */
+ J721S2_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (F18) MCU_OSPI0_D3 */
+ J721S2_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (E19) MCU_OSPI0_D4 */
+ J721S2_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (G19) MCU_OSPI0_D5 */
+ J721S2_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (F19) MCU_OSPI0_D6 */
+ J721S2_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (F20) MCU_OSPI0_D7 */
+ J721S2_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (E18) MCU_OSPI0_DQS */
+ >;
+ };
+};
+
&wkup_pmx2 {
wkup_i2c0_pins_default: wkup-i2c0-default-pins {
pinctrl-single,pins = <
@@ -152,6 +170,66 @@ eeprom@51 {
};
};
+&ospi0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0x0>;
+ spi-tx-bus-width = <8>;
+ spi-rx-bus-width = <8>;
+ spi-max-frequency = <25000000>;
+ cdns,tshsl-ns = <60>;
+ cdns,tsd2d-ns = <60>;
+ cdns,tchsh-ns = <60>;
+ cdns,tslch-ns = <60>;
+ cdns,read-delay = <4>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "ospi.tiboot3";
+ reg = <0x0 0x80000>;
+ };
+
+ partition@80000 {
+ label = "ospi.tispl";
+ reg = <0x80000 0x200000>;
+ };
+
+ partition@280000 {
+ label = "ospi.u-boot";
+ reg = <0x280000 0x400000>;
+ };
+
+ partition@680000 {
+ label = "ospi.env";
+ reg = <0x680000 0x40000>;
+ };
+
+ partition@6c0000 {
+ label = "ospi.env.backup";
+ reg = <0x6c0000 0x40000>;
+ };
+
+ partition@800000 {
+ label = "ospi.rootfs";
+ reg = <0x800000 0x37c0000>;
+ };
+
+ partition@3fc0000 {
+ label = "ospi.phypattern";
+ reg = <0x3fc0000 0x40000>;
+ };
+ };
+ };
+};
+
&mailbox0_cluster0 {
status = "okay";
interrupts = <436>;