[v4,3/3] docs: iio: add documentation for adis16475 driver
Commit Message
Add documentation for adis16475 driver which describes
the driver device files and shows how the user may use the
ABI for various scenarios (configuration, measurement, etc.).
Signed-off-by: Ramona Gradinariu <ramona.gradinariu@analog.com>
---
changes in v4:
- fixed typos
- added IIO interfacing tools section
Documentation/iio/adis16475.rst | 406 ++++++++++++++++++++++++++++++++
Documentation/iio/index.rst | 1 +
2 files changed, 407 insertions(+)
create mode 100644 Documentation/iio/adis16475.rst
--
2.34.1
new file mode 100644
@@ -0,0 +1,406 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+================
+ADIS16475 driver
+================
+
+This driver supports Analog Device's IMUs on SPI bus.
+
+1. Supported devices
+====================
+
+* `ADIS16465 <https://www.analog.com/ADIS16465>`_
+* `ADIS16467 <https://www.analog.com/ADIS16467>`_
+* `ADIS16470 <https://www.analog.com/ADIS16470>`_
+* `ADIS16475 <https://www.analog.com/ADIS16475>`_
+* `ADIS16477 <https://www.analog.com/ADIS16477>`_
+* `ADIS16500 <https://www.analog.com/ADIS16500>`_
+* `ADIS16505 <https://www.analog.com/ADIS16505>`_
+* `ADIS16507 <https://www.analog.com/ADIS16507>`_
+
+Each supported device is a precision, miniature microelectromechanical system
+(MEMS) inertial measurement unit (IMU) that includes a triaxial gyroscope and a
+triaxial accelerometer. Each inertial sensor in the IMU device combines with
+signal conditioning that optimizes dynamic performance. The factory calibration
+characterizes each sensor for sensitivity, bias, alignment, linear acceleration
+(gyroscope bias), and point of percussion (accelerometer location). As a result,
+each sensor has dynamic compensation formulas that provide accurate sensor
+measurements over a broad set of conditions.
+
+2. Device attributes
+====================
+
+Accelerometer, gyroscope measurements are always provided. Furthermore, the
+driver offers the capability to retrieve the delta angle and the delta velocity
+measurements computed by the device.
+
+The delta angle measurements represent a calculation of angular displacement
+between each sample update, while the delta velocity measurements represent a
+calculation of linear velocity change between each sample update.
+
+Finally, temperature data are provided which show a coarse measurement of
+the temperature inside of the IMU device. This data is most useful for
+monitoring relative changes in the thermal environment.
+
+The signal chain of each inertial sensor (accelerometers and gyroscopes)
+includes the application of unique correction formulas, which are derived from
+extensive characterization of bias, sensitivity, alignment, response to linear
+acceleration (gyroscopes), and point of percussion (accelerometer location)
+over a temperature range of −40°C to +85°C, for each ADIS device. These
+correction formulas are not accessible, but users do have the opportunity to
+adjust the bias for each sensor individually through the calibbias attribute.
+
+Each IIO device, has a device folder under /sys/bus/iio/devices/iio:deviceX,
+where X is the IIO index of the device. Under these folders reside a set of
+device files, depending on the characteristics and features of the hardware
+device in questions. These files are consistently generalized and documented in
+the IIO ABI documentation.
+
+The following tables show the adis16475 related device files, found in the
+specific device folder path /sys/bus/iio/devices/iio:deviceX.
+
++-------------------------------------------+----------------------------------------------------------+
+| 3-Axis Accelerometer related device files | Description |
++-------------------------------------------+----------------------------------------------------------+
+| in_accel_scale | Scale for the accelerometer channels. |
++-------------------------------------------+----------------------------------------------------------+
+| in_accel_x_calibbias | Calibration offset for the X-axis accelerometer channel. |
++-------------------------------------------+----------------------------------------------------------+
+| in_accel_calibbias_x | x-axis acceleration offset correction |
++-------------------------------------------+----------------------------------------------------------+
+| in_accel_x_raw | Raw X-axis accelerometer channel value. |
++-------------------------------------------+----------------------------------------------------------+
+| in_accel_calibbias_y | y-axis acceleration offset correction |
++-------------------------------------------+----------------------------------------------------------+
+| in_accel_y_raw | Raw Y-axis accelerometer channel value. |
++-------------------------------------------+----------------------------------------------------------+
+| in_accel_z_calibbias | Calibration offset for the Z-axis accelerometer channel. |
++-------------------------------------------+----------------------------------------------------------+
+| in_accel_z_raw | Raw Z-axis accelerometer channel value. |
++-------------------------------------------+----------------------------------------------------------+
+| in_deltavelocity_scale | Scale for delta velocity channels. |
++-------------------------------------------+----------------------------------------------------------+
+| in_deltavelocity_x_raw | Raw X-axis delta velocity channel value. |
++-------------------------------------------+----------------------------------------------------------+
+| in_deltavelocity_y_raw | Raw Y-axis delta velocity channel value. |
++-------------------------------------------+----------------------------------------------------------+
+| in_deltavelocity_z_raw | Raw Z-axis delta velocity channel value. |
++-------------------------------------------+----------------------------------------------------------+
+
++---------------------------------------+------------------------------------------------------+
+| 3-Axis Gyroscope related device files | Description |
++---------------------------------------+------------------------------------------------------+
+| in_anglvel_scale | Scale for the gyroscope channels. |
++---------------------------------------+------------------------------------------------------+
+| in_anglvel_x_calibbias | Calibration offset for the X-axis gyroscope channel. |
++---------------------------------------+------------------------------------------------------+
+| in_anglvel_calibbias_x | x-axis gyroscope offset correction |
++---------------------------------------+------------------------------------------------------+
+| in_anglvel_x_raw | Raw X-axis gyroscope channel value. |
++---------------------------------------+------------------------------------------------------+
+| in_anglvel_calibbias_y | y-axis gyroscope offset correction |
++---------------------------------------+------------------------------------------------------+
+| in_anglvel_y_raw | Raw Y-axis gyroscope channel value. |
++---------------------------------------+------------------------------------------------------+
+| in_anglvel_z_calibbias | Calibration offset for the Z-axis gyroscope channel. |
++---------------------------------------+------------------------------------------------------+
+| in_anglvel_z_raw | Raw Z-axis gyroscope channel value. |
++---------------------------------------+------------------------------------------------------+
+| in_deltaangl_scale | Scale for delta angle channels. |
++---------------------------------------+------------------------------------------------------+
+| in_deltaangl_x_raw | Raw X-axis delta angle channel value. |
++---------------------------------------+------------------------------------------------------+
+| in_deltaangl_y_raw | Raw Y-axis delta angle channel value. |
++---------------------------------------+------------------------------------------------------+
+| in_deltaangl_z_raw | Raw Z-axis delta angle channel value. |
++---------------------------------------+------------------------------------------------------+
+
++----------------------------------+-------------------------------------------+
+| Temperature sensor related files | Description |
++----------------------------------+-------------------------------------------+
+| in_temp0_raw | Raw temperature channel value. |
++----------------------------------+-------------------------------------------+
+| in_temp0_scale | Scale for the temperature sensor channel. |
++----------------------------------+-------------------------------------------+
+
++-------------------------------+---------------------------------------------------------+
+| Miscellaneous device files | Description |
++-------------------------------+---------------------------------------------------------+
+| name | Name of the IIO device. |
++-------------------------------+---------------------------------------------------------+
+| sampling_frequency | Currently selected sample rate. |
++-------------------------------+---------------------------------------------------------+
+| filter_low_pass_3db_frequency | Bandwidth for the accelerometer and gyroscope channels. |
++-------------------------------+---------------------------------------------------------+
+
+The following table shows the adis16475 related device debug files, found in the
+specific device debug folder path /sys/kernel/debug/iio/iio:deviceX.
+
++----------------------+-------------------------------------------------------------------------+
+| Debugfs device files | Description |
++----------------------+-------------------------------------------------------------------------+
+| serial_number | The serial number of the chip in hexadecimal format. |
++----------------------+-------------------------------------------------------------------------+
+| product_id | Chip specific product id (e.g. 16475, 16500, 16505, etc.). |
++----------------------+-------------------------------------------------------------------------+
+| flash_count | The number of flash writes performed on the device. |
++----------------------+-------------------------------------------------------------------------+
+| firmware_revision | String containing the firmware revision in the following format ##.##. |
++----------------------+-------------------------------------------------------------------------+
+| firmware_date | String containing the firmware date in the following format mm-dd-yyyy. |
++----------------------+-------------------------------------------------------------------------+
+
+Channels processed values
+-------------------------
+
+A channel value can be read from its _raw attribute. The value returned is the
+raw value as reported by the devices. To get the processed value of the channel,
+apply the following formula:
+
+.. code-block:: bash
+
+ processed value = (_raw + _offset) * _scale
+
+Where _offset and _scale are device attributes. If no _offset attribute is
+present, simply assume its value is 0.
+
+The adis16475 driver offers data for 5 types of channels, the table below shows
+the measurement units for the processed value, which are defined by the IIO
+framework:
+
++-------------------------------------+---------------------------+
+| Channel type | Measurement unit |
++-------------------------------------+---------------------------+
+| Acceleration on X, Y, and Z axis | Meters per Second squared |
++-------------------------------------+---------------------------+
+| Angular velocity on X, Y and Z axis | Radians per second |
++-------------------------------------+---------------------------+
+| Delta velocity on X. Y, and Z axis | Meters per Second |
++-------------------------------------+---------------------------+
+| Delta angle on X, Y, and Z axis | Radians |
++-------------------------------------+---------------------------+
+| Temperature | Millidegrees Celsius |
++-------------------------------------+---------------------------+
+
+Usage examples
+--------------
+
+Show device name:
+
+.. code-block:: bash
+
+ root:/sys/bus/iio/devices/iio:device0> cat name
+ adis16505-2
+
+Show accelerometer channels value:
+
+.. code-block:: bash
+
+ root:/sys/bus/iio/devices/iio:device0> cat in_accel_x_raw
+ -275924
+ root:/sys/bus/iio/devices/iio:device0> cat in_accel_y_raw
+ -30142222
+ root:/sys/bus/iio/devices/iio:device0> cat in_accel_z_raw
+ 261265769
+ root:/sys/bus/iio/devices/iio:device0> cat in_accel_scale
+ 0.000000037
+
+- X-axis acceleration = in_accel_x_raw * in_accel_scale = −0.010209188 m/s^2
+- Y-axis acceleration = in_accel_y_raw * in_accel_scale = −1.115262214 m/s^2
+- Z-axis acceleration = in_accel_z_raw * in_accel_scale = 9.666833453 m/s^2
+
+Show gyroscope channels value:
+
+.. code-block:: bash
+
+ root:/sys/bus/iio/devices/iio:device0> cat in_anglvel_x_raw
+ -3324626
+ root:/sys/bus/iio/devices/iio:device0> cat in_anglvel_y_raw
+ 1336980
+ root:/sys/bus/iio/devices/iio:device0> cat in_anglvel_z_raw
+ -602983
+ root:/sys/bus/iio/devices/iio:device0> cat in_anglvel_scale
+ 0.000000006
+
+- X-axis angular velocity = in_anglvel_x_raw * in_anglvel_scale = −0.019947756 rad/s
+- Y-axis angular velocity = in_anglvel_y_raw * in_anglvel_scale = 0.00802188 rad/s
+- Z-axis angular velocity = in_anglvel_z_raw * in_anglvel_scale = −0.003617898 rad/s
+
+Set calibration offset for accelerometer channels:
+
+.. code-block:: bash
+
+ root:/sys/bus/iio/devices/iio:device0> cat in_accel_x_calibbias
+ 0
+
+ root:/sys/bus/iio/devices/iio:device0> echo 5000 > in_accel_x_calibbias
+ root:/sys/bus/iio/devices/iio:device0> cat in_accel_x_calibbias
+ 5000
+
+Set calibration offset for gyroscope channels:
+
+.. code-block:: bash
+
+ root:/sys/bus/iio/devices/iio:device0> cat in_anglvel_y_calibbias
+ 0
+
+ root:/sys/bus/iio/devices/iio:device0> echo -5000 > in_anglvel_y_calibbias
+ root:/sys/bus/iio/devices/iio:device0> cat in_anglvel_y_calibbias
+ -5000
+
+Set sampling frequency:
+
+.. code-block:: bash
+
+ root:/sys/bus/iio/devices/iio:device0> cat sampling_frequency
+ 2000.000000
+
+ root:/sys/bus/iio/devices/iio:device0> echo 1000 > sampling_frequency
+ 1000.000000
+
+Set bandwidth for accelerometer and gyroscope:
+
+.. code-block:: bash
+
+ root:/sys/bus/iio/devices/iio:device0> cat filter_low_pass_3db_frequency
+ 720
+
+ root:/sys/bus/iio/devices/iio:device0> echo 360 > filter_low_pass_3db_frequency
+ root:/sys/bus/iio/devices/iio:device0> cat filter_low_pass_3db_frequency
+ 360
+
+Show serial number:
+
+.. code-block:: bash
+
+ root:/sys/kernel/debug/iio/iio:device0> cat serial_number
+ 0x04f9
+
+Show product id:
+
+.. code-block:: bash
+
+ root:/sys/kernel/debug/iio/iio:device0> cat product_id
+ 16505
+
+Show flash count:
+
+.. code-block:: bash
+
+ root:/sys/kernel/debug/iio/iio:device0> cat flash_count
+ 150
+
+Show firmware revision:
+
+.. code-block:: bash
+
+ root:/sys/kernel/debug/iio/iio:device0> cat firmware_revision
+ 1.6
+
+Show firmware date:
+
+.. code-block:: bash
+
+ root:/sys/kernel/debug/iio/iio:device0> cat firmware_date
+ 06-27-2019
+
+3. Device buffers
+=================
+
+This driver supports IIO buffers.
+
+All devices support retrieving the raw acceleration, gyroscope and temperature
+measurements using buffers.
+
+The following device families also support retrieving the delta velocity, delta
+angle and temperature measurements using buffers:
+ - ADIS16477
+ - ADIS16500
+ - ADIS16505
+ - ADIS16507
+
+However, when retrieving acceleration or gyroscope data using buffers, delta
+readings will not be available and vice versa.
+
+Usage examples
+--------------
+
+Set device trigger in current_trigger, if not already set:
+
+.. code-block:: bash
+
+ root:/sys/bus/iio/devices/iio:device0> cat trigger/current_trigger
+
+ root:/sys/bus/iio/devices/iio:device0> echo adis16505-2-dev0 > trigger/current_trigger
+ root:/sys/bus/iio/devices/iio:device0> cat trigger/current_trigger
+ adis16505-2-dev0
+
+Select channels for buffer read:
+
+.. code-block:: bash
+
+ root:/sys/bus/iio/devices/iio:device0> echo 1 > scan_elements/in_deltavelocity_x_en
+ root:/sys/bus/iio/devices/iio:device0> echo 1 > scan_elements/in_deltavelocity_y_en
+ root:/sys/bus/iio/devices/iio:device0> echo 1 > scan_elements/in_deltavelocity_z_en
+ root:/sys/bus/iio/devices/iio:device0> echo 1 > scan_elements/in_temp0_en
+
+Set the number of samples to be stored in the buffer:
+
+.. code-block:: bash
+
+ root:/sys/bus/iio/devices/iio:device0> echo 10 > buffer/length
+
+Enable buffer readings:
+
+.. code-block:: bash
+
+ root:/sys/bus/iio/devices/iio:device0> echo 1 > buffer/enable
+
+Obtain buffered data:
+
+.. code-block:: bash
+
+ root:/sys/bus/iio/devices/iio:device0> hexdump -C /dev/iio\:device0
+ ...
+ 00001680 01 1f 00 00 ff ff fe ef 00 00 47 bf 00 03 35 55 |..........G...5U|
+ 00001690 01 1f 00 00 ff ff ff d9 00 00 46 f1 00 03 35 35 |..........F...55|
+ 000016a0 01 1f 00 00 ff ff fe fc 00 00 46 cb 00 03 35 7b |..........F...5{|
+ 000016b0 01 1f 00 00 ff ff fe 41 00 00 47 0d 00 03 35 8b |.......A..G...5.|
+ 000016c0 01 1f 00 00 ff ff fe 37 00 00 46 b4 00 03 35 90 |.......7..F...5.|
+ 000016d0 01 1d 00 00 ff ff fe 5a 00 00 45 d7 00 03 36 08 |.......Z..E...6.|
+ 000016e0 01 1b 00 00 ff ff fe fb 00 00 45 e7 00 03 36 60 |..........E...6`|
+ 000016f0 01 1a 00 00 ff ff ff 17 00 00 46 bc 00 03 36 de |..........F...6.|
+ 00001700 01 1a 00 00 ff ff fe 59 00 00 46 d7 00 03 37 b8 |.......Y..F...7.|
+ 00001710 01 1a 00 00 ff ff fe ae 00 00 46 95 00 03 37 ba |..........F...7.|
+ 00001720 01 1a 00 00 ff ff fe c5 00 00 46 63 00 03 37 9f |..........Fc..7.|
+ 00001730 01 1a 00 00 ff ff fe 55 00 00 46 89 00 03 37 c1 |.......U..F...7.|
+ 00001740 01 1a 00 00 ff ff fe 31 00 00 46 aa 00 03 37 f7 |.......1..F...7.|
+ ...
+
+See Documentation/iio/iio_devbuf.rst for more information about how buffered
+data is structured.
+
+4. IIO Interfacing Tools
+========================
+
+Linux Kernel Tools
+------------------
+
+Linux Kernel provides some user space tools that can be used to retrieve data
+from IIO sysfs:
+
+* lsiio: example application that provides a list of IIO devices and triggers
+* iio_event_monitor: example application that reads events from an IIO device
+ and prints them
+* iio_generic_buffer: example application that reads data from buffer
+* iio_utils: set of APIs, typically used to access sysfs files.
+
+LibIIO
+------
+
+LibIIO is a C/C++ library that provides generic access to IIO devices. The
+library abstracts the low-level details of the hardware, and provides a simple
+yet complete programming interface that can be used for advanced projects.
+
+For more information about LibIIO, please see:
+https://github.com/analogdevicesinc/libiio
@@ -16,5 +16,6 @@ Industrial I/O Kernel Drivers
.. toctree::
:maxdepth: 1
+ adis16475
bno055
ep93xx_adc