[v4,2/3] arm64: dts: ti: k3-am642-evm: add ICSSG1 Ethernet support
Commit Message
ICSSG1 provides dual Gigabit Ethernet support with proper FW loaded.
The ICSSG1 MII0 (RGMII1) has DP83869 PHY attached to it. The ICSSG1 shares
MII1 (RGMII2) PHY DP83869 with CPSW3g and it's assigned by default to
CPSW3g. The MDIO access to MII1 (RGMII2) PHY DP83869 is controlled by MDIO
bus switch and also assigned to CPSW3g. Therefore the ICSSG1 MII1 (RGMII2)
port is kept disable and ICSSG1 is enabled in single MAC mode by
default.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
---
arch/arm64/boot/dts/ti/k3-am642-evm.dts | 97 +++++++++++++++++++++++++
1 file changed, 97 insertions(+)
Comments
On 05/02/2024 11:05, MD Danish Anwar wrote:
> ICSSG1 provides dual Gigabit Ethernet support with proper FW loaded.
>
> The ICSSG1 MII0 (RGMII1) has DP83869 PHY attached to it. The ICSSG1 shares
> MII1 (RGMII2) PHY DP83869 with CPSW3g and it's assigned by default to
> CPSW3g. The MDIO access to MII1 (RGMII2) PHY DP83869 is controlled by MDIO
> bus switch and also assigned to CPSW3g. Therefore the ICSSG1 MII1 (RGMII2)
> port is kept disable and ICSSG1 is enabled in single MAC mode by
> default.
>
> Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
> Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
> ---
> arch/arm64/boot/dts/ti/k3-am642-evm.dts | 97 +++++++++++++++++++++++++
> 1 file changed, 97 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am642-evm.dts b/arch/arm64/boot/dts/ti/k3-am642-evm.dts
> index 8c5651d2cf5d..6b97e447c486 100644
> --- a/arch/arm64/boot/dts/ti/k3-am642-evm.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am642-evm.dts
> @@ -32,6 +32,7 @@ aliases {
> mmc1 = &sdhci1;
> ethernet0 = &cpsw_port1;
> ethernet1 = &cpsw_port2;
> + ethernet2 = &icssg1_emac0;
> };
>
> memory@80000000 {
> @@ -229,6 +230,66 @@ transceiver2: can-phy1 {
> max-bitrate = <5000000>;
> standby-gpios = <&exp1 9 GPIO_ACTIVE_HIGH>;
> };
> +
> + icssg1_eth: icssg1-eth {
> + compatible = "ti,am642-icssg-prueth";
> + pinctrl-names = "default";
> + pinctrl-0 = <&icssg1_rgmii1_pins_default>;
> + sram = <&oc_sram>;
> + ti,prus = <&pru1_0>, <&rtu1_0>, <&tx_pru1_0>, <&pru1_1>, <&rtu1_1>, <&tx_pru1_1>;
> + firmware-name = "ti-pruss/am64x-sr2-pru0-prueth-fw.elf",
> + "ti-pruss/am64x-sr2-rtu0-prueth-fw.elf",
> + "ti-pruss/am64x-sr2-txpru0-prueth-fw.elf",
> + "ti-pruss/am64x-sr2-pru1-prueth-fw.elf",
> + "ti-pruss/am64x-sr2-rtu1-prueth-fw.elf",
> + "ti-pruss/am64x-sr2-txpru1-prueth-fw.elf";
> +
> + ti,pruss-gp-mux-sel = <2>, /* MII mode */
> + <2>,
> + <2>,
> + <2>, /* MII mode */
> + <2>,
> + <2>;
> + ti,mii-g-rt = <&icssg1_mii_g_rt>;
> + ti,mii-rt = <&icssg1_mii_rt>;
> + ti,iep = <&icssg1_iep0>, <&icssg1_iep1>;
> + interrupt-parent = <&icssg1_intc>;
> + interrupts = <24 0 2>, <25 1 3>;
> + interrupt-names = "tx_ts0", "tx_ts1";
> + dmas = <&main_pktdma 0xc200 15>, /* egress slice 0 */
> + <&main_pktdma 0xc201 15>, /* egress slice 0 */
> + <&main_pktdma 0xc202 15>, /* egress slice 0 */
> + <&main_pktdma 0xc203 15>, /* egress slice 0 */
> + <&main_pktdma 0xc204 15>, /* egress slice 1 */
> + <&main_pktdma 0xc205 15>, /* egress slice 1 */
> + <&main_pktdma 0xc206 15>, /* egress slice 1 */
> + <&main_pktdma 0xc207 15>, /* egress slice 1 */
> + <&main_pktdma 0x4200 15>, /* ingress slice 0 */
> + <&main_pktdma 0x4201 15>; /* ingress slice 1 */
> + dma-names = "tx0-0", "tx0-1", "tx0-2", "tx0-3",
> + "tx1-0", "tx1-1", "tx1-2", "tx1-3",
> + "rx0", "rx1";
> +
> + ethernet-ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + icssg1_emac0: port@0 {
> + reg = <0>;
> + phy-handle = <&icssg1_phy1>;
> + phy-mode = "rgmii-id";
> + ti,syscon-rgmii-delay = <&main_conf 0x4110>;
"syscon" compatible will be eventually dropped from the main_conf node.
It is not there on other platforms e.g. am62p
One solution is to add a device tree node in main_conf and reference to
that.
e.g.
https://lore.kernel.org/all/20240205135908.54656-3-rogerq@kernel.org/
> + /* Filled in by bootloader */
> + local-mac-address = [00 00 00 00 00 00];
> + };
> + icssg1_emac1: port@1 {
> + reg = <1>;
> + ti,syscon-rgmii-delay = <&main_conf 0x4114>;
here too
> + /* Filled in by bootloader */
> + local-mac-address = [00 00 00 00 00 00];
> + status = "disabled";
> + };
> + };
> + };
> };
>
> &main_pmx0 {
> @@ -383,6 +444,30 @@ ddr_vtt_pins_default: ddr-vtt-default-pins {
> AM64X_IOPAD(0x0030, PIN_OUTPUT_PULLUP, 7) /* (L18) OSPI0_CSN1.GPIO0_12 */
> >;
> };
> +
> + icssg1_mdio1_pins_default: icssg1-mdio1-default-pins {
> + pinctrl-single,pins = <
> + AM64X_IOPAD(0x015c, PIN_OUTPUT, 0) /* (Y6) PRG1_MDIO0_MDC */
> + AM64X_IOPAD(0x0158, PIN_INPUT, 0) /* (AA6) PRG1_MDIO0_MDIO */
> + >;
> + };
> +
> + icssg1_rgmii1_pins_default: icssg1-rgmii1-default-pins{
> + pinctrl-single,pins = <
> + AM64X_IOPAD(0x00b8, PIN_INPUT, 2) /* (Y7) PRG1_PRU0_GPO0.PRG1_RGMII1_RD0 */
> + AM64X_IOPAD(0x00bc, PIN_INPUT, 2) /* (U8) PRG1_PRU0_GPO1.PRG1_RGMII1_RD1 */
> + AM64X_IOPAD(0x00c0, PIN_INPUT, 2) /* (W8) PRG1_PRU0_GPO2.PRG1_RGMII1_RD2 */
> + AM64X_IOPAD(0x00c4, PIN_INPUT, 2) /* (V8) PRG1_PRU0_GPO3.PRG1_RGMII1_RD3 */
> + AM64X_IOPAD(0x00d0, PIN_INPUT, 2) /* (AA7) PRG1_PRU0_GPO6.PRG1_RGMII1_RXC */
> + AM64X_IOPAD(0x00c8, PIN_INPUT, 2) /* (Y8) PRG1_PRU0_GPO4.PRG1_RGMII1_RX_CTL */
> + AM64X_IOPAD(0x00e4, PIN_INPUT, 2) /* (AA8) PRG1_PRU0_GPO11.PRG1_RGMII1_TD0 */
> + AM64X_IOPAD(0x00e8, PIN_INPUT, 2) /* (U9) PRG1_PRU0_GPO12.PRG1_RGMII1_TD1 */
> + AM64X_IOPAD(0x00ec, PIN_INPUT, 2) /* (W9) PRG1_PRU0_GPO13.PRG1_RGMII1_TD2 */
> + AM64X_IOPAD(0x00f0, PIN_INPUT, 2) /* (AA9) PRG1_PRU0_GPO14.PRG1_RGMII1_TD3 */
> + AM64X_IOPAD(0x00f8, PIN_INPUT, 2) /* (V9) PRG1_PRU0_GPO16.PRG1_RGMII1_TXC */
> + AM64X_IOPAD(0x00f4, PIN_INPUT, 2) /* (Y9) PRG1_PRU0_GPO15.PRG1_RGMII1_TX_CTL */
> + >;
> + };
> };
>
> &main_uart0 {
> @@ -731,3 +816,15 @@ &main_mcan1 {
> pinctrl-0 = <&main_mcan1_pins_default>;
> phys = <&transceiver2>;
> };
> +
> +&icssg1_mdio {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&icssg1_mdio1_pins_default>;
> +
> + icssg1_phy1: ethernet-phy@f {
> + reg = <0xf>;
> + tx-internal-delay-ps = <250>;
> + rx-internal-delay-ps = <2000>;
> + };
> +};
@@ -32,6 +32,7 @@ aliases {
mmc1 = &sdhci1;
ethernet0 = &cpsw_port1;
ethernet1 = &cpsw_port2;
+ ethernet2 = &icssg1_emac0;
};
memory@80000000 {
@@ -229,6 +230,66 @@ transceiver2: can-phy1 {
max-bitrate = <5000000>;
standby-gpios = <&exp1 9 GPIO_ACTIVE_HIGH>;
};
+
+ icssg1_eth: icssg1-eth {
+ compatible = "ti,am642-icssg-prueth";
+ pinctrl-names = "default";
+ pinctrl-0 = <&icssg1_rgmii1_pins_default>;
+ sram = <&oc_sram>;
+ ti,prus = <&pru1_0>, <&rtu1_0>, <&tx_pru1_0>, <&pru1_1>, <&rtu1_1>, <&tx_pru1_1>;
+ firmware-name = "ti-pruss/am64x-sr2-pru0-prueth-fw.elf",
+ "ti-pruss/am64x-sr2-rtu0-prueth-fw.elf",
+ "ti-pruss/am64x-sr2-txpru0-prueth-fw.elf",
+ "ti-pruss/am64x-sr2-pru1-prueth-fw.elf",
+ "ti-pruss/am64x-sr2-rtu1-prueth-fw.elf",
+ "ti-pruss/am64x-sr2-txpru1-prueth-fw.elf";
+
+ ti,pruss-gp-mux-sel = <2>, /* MII mode */
+ <2>,
+ <2>,
+ <2>, /* MII mode */
+ <2>,
+ <2>;
+ ti,mii-g-rt = <&icssg1_mii_g_rt>;
+ ti,mii-rt = <&icssg1_mii_rt>;
+ ti,iep = <&icssg1_iep0>, <&icssg1_iep1>;
+ interrupt-parent = <&icssg1_intc>;
+ interrupts = <24 0 2>, <25 1 3>;
+ interrupt-names = "tx_ts0", "tx_ts1";
+ dmas = <&main_pktdma 0xc200 15>, /* egress slice 0 */
+ <&main_pktdma 0xc201 15>, /* egress slice 0 */
+ <&main_pktdma 0xc202 15>, /* egress slice 0 */
+ <&main_pktdma 0xc203 15>, /* egress slice 0 */
+ <&main_pktdma 0xc204 15>, /* egress slice 1 */
+ <&main_pktdma 0xc205 15>, /* egress slice 1 */
+ <&main_pktdma 0xc206 15>, /* egress slice 1 */
+ <&main_pktdma 0xc207 15>, /* egress slice 1 */
+ <&main_pktdma 0x4200 15>, /* ingress slice 0 */
+ <&main_pktdma 0x4201 15>; /* ingress slice 1 */
+ dma-names = "tx0-0", "tx0-1", "tx0-2", "tx0-3",
+ "tx1-0", "tx1-1", "tx1-2", "tx1-3",
+ "rx0", "rx1";
+
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ icssg1_emac0: port@0 {
+ reg = <0>;
+ phy-handle = <&icssg1_phy1>;
+ phy-mode = "rgmii-id";
+ ti,syscon-rgmii-delay = <&main_conf 0x4110>;
+ /* Filled in by bootloader */
+ local-mac-address = [00 00 00 00 00 00];
+ };
+ icssg1_emac1: port@1 {
+ reg = <1>;
+ ti,syscon-rgmii-delay = <&main_conf 0x4114>;
+ /* Filled in by bootloader */
+ local-mac-address = [00 00 00 00 00 00];
+ status = "disabled";
+ };
+ };
+ };
};
&main_pmx0 {
@@ -383,6 +444,30 @@ ddr_vtt_pins_default: ddr-vtt-default-pins {
AM64X_IOPAD(0x0030, PIN_OUTPUT_PULLUP, 7) /* (L18) OSPI0_CSN1.GPIO0_12 */
>;
};
+
+ icssg1_mdio1_pins_default: icssg1-mdio1-default-pins {
+ pinctrl-single,pins = <
+ AM64X_IOPAD(0x015c, PIN_OUTPUT, 0) /* (Y6) PRG1_MDIO0_MDC */
+ AM64X_IOPAD(0x0158, PIN_INPUT, 0) /* (AA6) PRG1_MDIO0_MDIO */
+ >;
+ };
+
+ icssg1_rgmii1_pins_default: icssg1-rgmii1-default-pins{
+ pinctrl-single,pins = <
+ AM64X_IOPAD(0x00b8, PIN_INPUT, 2) /* (Y7) PRG1_PRU0_GPO0.PRG1_RGMII1_RD0 */
+ AM64X_IOPAD(0x00bc, PIN_INPUT, 2) /* (U8) PRG1_PRU0_GPO1.PRG1_RGMII1_RD1 */
+ AM64X_IOPAD(0x00c0, PIN_INPUT, 2) /* (W8) PRG1_PRU0_GPO2.PRG1_RGMII1_RD2 */
+ AM64X_IOPAD(0x00c4, PIN_INPUT, 2) /* (V8) PRG1_PRU0_GPO3.PRG1_RGMII1_RD3 */
+ AM64X_IOPAD(0x00d0, PIN_INPUT, 2) /* (AA7) PRG1_PRU0_GPO6.PRG1_RGMII1_RXC */
+ AM64X_IOPAD(0x00c8, PIN_INPUT, 2) /* (Y8) PRG1_PRU0_GPO4.PRG1_RGMII1_RX_CTL */
+ AM64X_IOPAD(0x00e4, PIN_INPUT, 2) /* (AA8) PRG1_PRU0_GPO11.PRG1_RGMII1_TD0 */
+ AM64X_IOPAD(0x00e8, PIN_INPUT, 2) /* (U9) PRG1_PRU0_GPO12.PRG1_RGMII1_TD1 */
+ AM64X_IOPAD(0x00ec, PIN_INPUT, 2) /* (W9) PRG1_PRU0_GPO13.PRG1_RGMII1_TD2 */
+ AM64X_IOPAD(0x00f0, PIN_INPUT, 2) /* (AA9) PRG1_PRU0_GPO14.PRG1_RGMII1_TD3 */
+ AM64X_IOPAD(0x00f8, PIN_INPUT, 2) /* (V9) PRG1_PRU0_GPO16.PRG1_RGMII1_TXC */
+ AM64X_IOPAD(0x00f4, PIN_INPUT, 2) /* (Y9) PRG1_PRU0_GPO15.PRG1_RGMII1_TX_CTL */
+ >;
+ };
};
&main_uart0 {
@@ -731,3 +816,15 @@ &main_mcan1 {
pinctrl-0 = <&main_mcan1_pins_default>;
phys = <&transceiver2>;
};
+
+&icssg1_mdio {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&icssg1_mdio1_pins_default>;
+
+ icssg1_phy1: ethernet-phy@f {
+ reg = <0xf>;
+ tx-internal-delay-ps = <250>;
+ rx-internal-delay-ps = <2000>;
+ };
+};