[3/3] arm64: dts: ti: k3-j7200: Add support for multiple CAN instances
Commit Message
CAN instances 0 and 1 in the mcu domain are brought on the common
processor board through headers J30 and J31 respectively. Thus, add
their respective transceivers 1 and 2 dt nodes to add support for
these CAN instances.
CAN instance 3 in the main domain is brought on the common
processor board through header J27. The CAN High and Low lines
from the SoC are routed through a mux on the SoM. The select lines need
to be set for the CAN signals to get connected to the transceiver 3 on
the common processor board. Therefore, add transceiver dt nodes to add
support for this CAN instance.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
---
.../dts/ti/k3-j7200-common-proc-board.dts | 83 +++++++++++++++++++
1 file changed, 83 insertions(+)
@@ -88,6 +88,34 @@ vdd_sd_dv: gpio-regulator-TLV71033 {
states = <1800000 0x0>,
<3300000 0x1>;
};
+
+ transceiver1: can-phy1 {
+ compatible = "ti,tcan1043";
+ #phy-cells = <0>;
+ max-bitrate = <5000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcu_mcan0_gpio_pins_default>;
+ standby-gpios = <&wkup_gpio0 58 GPIO_ACTIVE_LOW>;
+ enable-gpios = <&wkup_gpio0 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ transceiver2: can-phy2 {
+ compatible = "ti,tcan1042";
+ #phy-cells = <0>;
+ max-bitrate = <5000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcu_mcan1_gpio_pins_default>;
+ standby-gpios = <&wkup_gpio0 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ transceiver3: can-phy3 {
+ compatible = "ti,tcan1043";
+ #phy-cells = <0>;
+ max-bitrate = <5000000>;
+ standby-gpios = <&exp2 7 GPIO_ACTIVE_LOW>;
+ enable-gpios = <&exp2 6 GPIO_ACTIVE_HIGH>;
+ mux-states = <&mux0 1>;
+ };
};
&wkup_pmx0 {
@@ -138,6 +166,33 @@ J721E_WKUP_IOPAD(0x0034, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
J721E_WKUP_IOPAD(0x0030, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
>;
};
+
+ mcu_mcan0_pins_default: mcu-mcan0-default-pins {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0x54, PIN_INPUT, 0) /* (A17) MCU_MCAN0_RX */
+ J721E_WKUP_IOPAD(0x50, PIN_OUTPUT, 0) /* (A16) MCU_MCAN0_TX */
+ >;
+ };
+
+ mcu_mcan1_pins_default: mcu-mcan1-default-pins {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0x6c, PIN_INPUT, 0) /* (B16) WKUP_GPIO0_5.MCU_MCAN1_RX */
+ J721E_WKUP_IOPAD(0x68, PIN_OUTPUT, 0) /* (D13) WKUP_GPIO0_4.MCU_MCAN1_TX */
+ >;
+ };
+
+ mcu_mcan0_gpio_pins_default: mcu-mcan0-gpio-default-pins {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0x58, PIN_INPUT, 7) /* (B18) WKUP_GPIO0_0 */
+ J721E_WKUP_IOPAD(0x40, PIN_INPUT, 7) /* (B17) MCU_SPI0_D1 */
+ >;
+ };
+
+ mcu_mcan1_gpio_pins_default: mcu-mcan1-gpio-default-pins {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0x60, PIN_INPUT, 7) /* (D14) WKUP_GPIO0_2 */
+ >;
+ };
};
&main_pmx0 {
@@ -189,6 +244,13 @@ vdd_sd_dv_pins_default: vdd-sd-dv-default-pins {
J721E_IOPAD(0xd0, PIN_OUTPUT, 7) /* (T5) SPI0_D1.GPIO0_55 */
>;
};
+
+ main_mcan3_pins_default: main-mcan3-default-pins {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x3c, PIN_INPUT, 0) /* (W16) MCAN3_RX */
+ J721E_IOPAD(0x38, PIN_OUTPUT, 0) /* (Y21) MCAN3_TX */
+ >;
+ };
};
&main_pmx1 {
@@ -394,3 +456,24 @@ &pcie1_ep {
num-lanes = <2>;
status = "disabled";
};
+
+&mcu_mcan0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcu_mcan0_pins_default>;
+ phys = <&transceiver1>;
+};
+
+&mcu_mcan1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcu_mcan1_pins_default>;
+ phys = <&transceiver2>;
+};
+
+&main_mcan3 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mcan3_pins_default>;
+ phys = <&transceiver3>;
+};