Remove the manual checks for register value changes in the
ksz8_w_phy_bmcr function. Instead, rely on regmap_update_bits() for
optimizing register updates.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
---
drivers/net/dsa/microchip/ksz8795.c | 96 +++++++++--------------------
1 file changed, 29 insertions(+), 67 deletions(-)
@@ -956,115 +956,77 @@ static int ksz8_w_phy_ctrl(struct ksz_device *dev, int port, u16 val)
*/
static int ksz8_w_phy_bmcr(struct ksz_device *dev, u16 port, u16 val)
{
+ u8 restart, speed, ctrl, restart_mask;
const u16 *regs = dev->info->regs;
- u8 restart, ctrl, speed, data;
int ret;
/* Do not support PHY reset function. */
if (val & BMCR_RESET)
return 0;
- ret = ksz_pread8(dev, port, regs[P_SPEED_STATUS], &speed);
- if (ret)
- return ret;
-
- data = speed;
+ speed = 0;
if (val & KSZ886X_BMCR_HP_MDIX)
- data |= PORT_HP_MDIX;
- else
- data &= ~PORT_HP_MDIX;
-
- if (data != speed) {
- ret = ksz_pwrite8(dev, port, regs[P_SPEED_STATUS], data);
- if (ret)
- return ret;
- }
+ speed |= PORT_HP_MDIX;
- ret = ksz_pread8(dev, port, regs[P_FORCE_CTRL], &ctrl);
+ ret = ksz_prmw8(dev, port, regs[P_SPEED_STATUS], PORT_HP_MDIX, speed);
if (ret)
return ret;
- data = ctrl;
+ ctrl = 0;
if (ksz_is_ksz88x3(dev)) {
if ((val & BMCR_ANENABLE))
- data |= PORT_AUTO_NEG_ENABLE;
- else
- data &= ~PORT_AUTO_NEG_ENABLE;
+ ctrl |= PORT_AUTO_NEG_ENABLE;
} else {
if (!(val & BMCR_ANENABLE))
- data |= PORT_AUTO_NEG_DISABLE;
- else
- data &= ~PORT_AUTO_NEG_DISABLE;
+ ctrl |= PORT_AUTO_NEG_DISABLE;
/* Fiber port does not support auto-negotiation. */
if (dev->ports[port].fiber)
- data |= PORT_AUTO_NEG_DISABLE;
+ ctrl |= PORT_AUTO_NEG_DISABLE;
}
if (val & BMCR_SPEED100)
- data |= PORT_FORCE_100_MBIT;
- else
- data &= ~PORT_FORCE_100_MBIT;
+ ctrl |= PORT_FORCE_100_MBIT;
if (val & BMCR_FULLDPLX)
- data |= PORT_FORCE_FULL_DUPLEX;
- else
- data &= ~PORT_FORCE_FULL_DUPLEX;
-
- if (data != ctrl) {
- ret = ksz_pwrite8(dev, port, regs[P_FORCE_CTRL], data);
- if (ret)
- return ret;
- }
+ ctrl |= PORT_FORCE_FULL_DUPLEX;
- ret = ksz_pread8(dev, port, regs[P_NEG_RESTART_CTRL], &restart);
+ ret = ksz_prmw8(dev, port, regs[P_FORCE_CTRL], PORT_FORCE_100_MBIT |
+ /* PORT_AUTO_NEG_ENABLE and PORT_AUTO_NEG_DISABLE are the same
+ * bits
+ */
+ PORT_FORCE_FULL_DUPLEX | PORT_AUTO_NEG_ENABLE, ctrl);
if (ret)
return ret;
- data = restart;
+ restart = 0;
+ restart_mask = PORT_LED_OFF | PORT_TX_DISABLE | PORT_AUTO_NEG_RESTART |
+ PORT_POWER_DOWN | PORT_AUTO_MDIX_DISABLE | PORT_FORCE_MDIX |
+ PORT_PHY_LOOPBACK;
+
if (val & KSZ886X_BMCR_DISABLE_LED)
- data |= PORT_LED_OFF;
- else
- data &= ~PORT_LED_OFF;
+ restart |= PORT_LED_OFF;
if (val & KSZ886X_BMCR_DISABLE_TRANSMIT)
- data |= PORT_TX_DISABLE;
- else
- data &= ~PORT_TX_DISABLE;
+ restart |= PORT_TX_DISABLE;
if (val & BMCR_ANRESTART)
- data |= PORT_AUTO_NEG_RESTART;
- else
- data &= ~(PORT_AUTO_NEG_RESTART);
+ restart |= PORT_AUTO_NEG_RESTART;
if (val & BMCR_PDOWN)
- data |= PORT_POWER_DOWN;
- else
- data &= ~PORT_POWER_DOWN;
+ restart |= PORT_POWER_DOWN;
if (val & KSZ886X_BMCR_DISABLE_AUTO_MDIX)
- data |= PORT_AUTO_MDIX_DISABLE;
- else
- data &= ~PORT_AUTO_MDIX_DISABLE;
+ restart |= PORT_AUTO_MDIX_DISABLE;
if (val & KSZ886X_BMCR_FORCE_MDI)
- data |= PORT_FORCE_MDIX;
- else
- data &= ~PORT_FORCE_MDIX;
+ restart |= PORT_FORCE_MDIX;
if (val & BMCR_LOOPBACK)
- data |= PORT_PHY_LOOPBACK;
- else
- data &= ~PORT_PHY_LOOPBACK;
-
- if (data != restart) {
- ret = ksz_pwrite8(dev, port, regs[P_NEG_RESTART_CTRL],
- data);
- if (ret)
- return ret;
- }
+ restart |= PORT_PHY_LOOPBACK;
- return 0;
+ return ksz_prmw8(dev, port, regs[P_NEG_RESTART_CTRL], restart_mask,
+ restart);
}
int ksz8_w_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 val)