diff mbox series

[v5,3/3] arm64: dts: allwinner: orange-pi-one-plus: Fix ethernet

Message ID 20231220203537.83479-4-jernej.skrabec@gmail.com
State New
Headers
Series arm64: add ethernet to orange pi 3 & one plus |

Commit Message

Jernej Škrabec Dec. 20, 2023, 8:35 p.m. UTC 
  Orange Pi One Plus has two regulators that power the Realtek RTL8211E
PHY. According to the datasheet, both regulators need to be enabled
at the same time, or that "phy-io" should be enabled slightly earlier
than "ephy" regulator.

RTL8211E/RTL8211EG datasheet says:

  Note 4: 2.5V (or 1.8/1.5V) RGMII power should be risen simultaneously
  or slightly earlier than 3.3V power. Rising 2.5V (or 1.8/1.5V) power
  later than 3.3V power may lead to errors.

Original submission ignored these rules, so it works in some cases but
not all. On top of that, regulator voltages don't reflect actual ones
in hardware. Rework ethernet and PHY nodes to properly reflect HW.

Fixes: 7ee32a17e0d6 ("arm64: dts: allwinner: h6: orangepi-one-plus: Enable ethernet")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
---
 .../allwinner/sun50i-h6-orangepi-one-plus.dts | 29 ++++++++++++++-----
 1 file changed, 22 insertions(+), 7 deletions(-)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts
index 29a081e72a9b..9c76eecaacce 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts
@@ -12,15 +12,15 @@  aliases {
 		ethernet0 = &emac;
 	};
 
-	reg_gmac_3v3: gmac-3v3 {
+	reg_gmac_2v5: gmac-2v5 {
 		compatible = "regulator-fixed";
-		regulator-name = "vcc-gmac-3v3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		startup-delay-us = <100000>;
+		regulator-name = "gmac-2v5";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
 		enable-active-high;
 		gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */
-		vin-supply = <&reg_aldo2>;
+		off-on-delay-us = <100000>;
+		vin-supply = <&reg_vcc5v>;
 	};
 };
 
@@ -29,7 +29,6 @@  &emac {
 	pinctrl-0 = <&ext_rgmii_pins>;
 	phy-mode = "rgmii-id";
 	phy-handle = <&ext_rgmii_phy>;
-	phy-supply = <&reg_gmac_3v3>;
 	allwinner,rx-delay-ps = <200>;
 	allwinner,tx-delay-ps = <200>;
 	status = "okay";
@@ -39,5 +38,21 @@  &mdio {
 	ext_rgmii_phy: ethernet-phy@1 {
 		compatible = "ethernet-phy-ieee802.3-c22";
 		reg = <1>;
+		/*
+		 * The board uses 2.5V RGMII signalling. Power sequence to enable
+		 * the phy is to enable GMAC-2V5 and GMAC-3V (aldo2) power rails
+		 * at the same time and to wait 100ms. The driver enables phy-io
+		 * first. Delay is achieved with enable-ramp-delay on reg_aldo2.
+		 */
+		phy-io-supply = <&reg_gmac_2v5>;
+		ephy-supply = <&reg_aldo2>;
+
+		reset-gpios = <&pio 3 14 GPIO_ACTIVE_LOW>; /* PD14 */
+		reset-assert-us = <15000>;
+		reset-deassert-us = <40000>;
 	};
 };
+
+&reg_aldo2 {
+	regulator-enable-ramp-delay = <100000>;
+};