[10/19] media: i2c: ov4689: Make horizontal blanking configurable

Message ID 20231211175023.1680247-11-mike.rudenko@gmail.com
State New
Headers
Series Omnivision OV4689 refactoring and improvements |

Commit Message

Mikhail Rudenko Dec. 11, 2023, 5:50 p.m. UTC
  Make horizontal blanking configurable. To do so, set HTS register
according to the requested horizontal blanking in ov4689_set_ctrl
instead of the register table. Default HTS value is not changed by
this patch. Minimal HTS value is found experimentally and corresponds
to 90 fps framerate at minimum vertical blanking. Real HTS value is
the register value multiplied by 4.

Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
---
 drivers/media/i2c/ov4689.c | 33 +++++++++++++++++++++------------
 1 file changed, 21 insertions(+), 12 deletions(-)
  

Comments

Laurent Pinchart Dec. 11, 2023, 10:08 p.m. UTC | #1
Hi Mikhail,

Thank you for the patch.

On Mon, Dec 11, 2023 at 08:50:13PM +0300, Mikhail Rudenko wrote:
> Make horizontal blanking configurable. To do so, set HTS register
> according to the requested horizontal blanking in ov4689_set_ctrl
> instead of the register table. Default HTS value is not changed by
> this patch. Minimal HTS value is found experimentally and corresponds
> to 90 fps framerate at minimum vertical blanking. Real HTS value is
> the register value multiplied by 4.
> 
> Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
> ---
>  drivers/media/i2c/ov4689.c | 33 +++++++++++++++++++++------------
>  1 file changed, 21 insertions(+), 12 deletions(-)
> 
> diff --git a/drivers/media/i2c/ov4689.c b/drivers/media/i2c/ov4689.c
> index 9fa06941a0e5..67d4004bdcfb 100644
> --- a/drivers/media/i2c/ov4689.c
> +++ b/drivers/media/i2c/ov4689.c
> @@ -30,7 +30,6 @@
>  #define OV4689_REG_EXPOSURE		CCI_REG24(0x3500)
>  #define OV4689_EXPOSURE_MIN		4
>  #define OV4689_EXPOSURE_STEP		1
> -#define OV4689_VTS_MAX			0x7fff
>  
>  #define OV4689_REG_GAIN			CCI_REG16(0x3508)
>  #define OV4689_GAIN_STEP		1
> @@ -41,6 +40,11 @@
>  #define OV4689_TEST_PATTERN_DISABLE	0x0
>  
>  #define OV4689_REG_VTS			CCI_REG16(0x380e)
> +#define OV4689_VTS_MAX			0x7fff
> +
> +#define OV4689_REG_HTS			CCI_REG16(0x380c)
> +#define OV4689_HTS_DIVIDER		4
> +#define OV4689_HTS_MAX			0x7fff

Could you move this just before REG_VTS to keep registers sorted by
address ?

>  
>  #define OV4689_LANES			4
>  #define OV4689_XVCLK_FREQ		24000000
> @@ -61,6 +65,7 @@ struct ov4689_mode {
>  	u32 width;
>  	u32 height;
>  	u32 hts_def;
> +	u32 hts_min;
>  	u32 vts_def;
>  	u32 exp_def;
>  	u32 pixel_rate;
> @@ -104,7 +109,7 @@ struct ov4689_gain_range {
>  
>  /*
>   * Xclk 24Mhz
> - * max_framerate 30fps
> + * max_framerate 90fps
>   * mipi_datarate per lane 1008Mbps
>   */
>  static const struct cci_reg_sequence ov4689_2688x1520_regs[] = {
> @@ -175,8 +180,6 @@ static const struct cci_reg_sequence ov4689_2688x1520_regs[] = {
>  	/* Timing control */
>  	{CCI_REG8(0x3801), 0x08}, /* H_CROP_START_L h_crop_start[7:0] = 0x08 */
>  	{CCI_REG8(0x3805), 0x97}, /* H_CROP_END_L h_crop_end[7:0] = 0x97 */
> -	{CCI_REG8(0x380c), 0x0a}, /* TIMING_HTS_H hts[14:8] = 0x0a */
> -	{CCI_REG8(0x380d), 0x0e}, /* TIMING_HTS_L hts[7:0] = 0x0e */
>  	{CCI_REG8(0x3811), 0x08}, /* H_WIN_OFF_L h_win_off[7:0] = 0x08*/
>  	{CCI_REG8(0x3813), 0x04}, /* V_WIN_OFF_L v_win_off[7:0] = 0x04 */
>  	{CCI_REG8(0x3819), 0x01}, /* VSYNC_END_L vsync_end_point[7:0] = 0x01 */
> @@ -237,7 +240,8 @@ static const struct ov4689_mode supported_modes[] = {
>  		.crop_top = 8,
>  		.crop_left = 16,
>  		.exp_def = 1536,
> -		.hts_def = 4 * 2574,
> +		.hts_def = 10296,
> +		.hts_min = 3432,
>  		.vts_def = 1554,
>  		.pixel_rate = 480000000,
>  		.reg_list = ov4689_2688x1520_regs,
> @@ -596,6 +600,11 @@ static int ov4689_set_ctrl(struct v4l2_ctrl *ctrl)
>  	case V4L2_CID_TEST_PATTERN:
>  		ret = ov4689_enable_test_pattern(ov4689, val);
>  		break;
> +	case V4L2_CID_HBLANK:
> +		cci_write(regmap, OV4689_REG_HTS,
> +			  (val + ov4689->cur_mode->width) /
> +			  OV4689_HTS_DIVIDER, &ret);
> +		break;
>  	default:
>  		dev_warn(dev, "%s Unhandled id:0x%x, val:0x%x\n",
>  			 __func__, ctrl->id, val);
> @@ -618,13 +627,13 @@ static int ov4689_initialize_controls(struct ov4689 *ov4689)
>  	struct v4l2_ctrl_handler *handler;
>  	const struct ov4689_mode *mode;
>  	s64 exposure_max, vblank_def;
> +	s64 hblank_def, hblank_min;
>  	struct v4l2_ctrl *ctrl;
> -	s64 h_blank_def;
>  	int ret;
>  
>  	handler = &ov4689->ctrl_handler;
>  	mode = ov4689->cur_mode;
> -	ret = v4l2_ctrl_handler_init(handler, 10);
> +	ret = v4l2_ctrl_handler_init(handler, 11);

The HBLANK control already exists, you're only changing how it is
initialized. I see 8 controls being created by the driver directly,
plus 2 created by v4l2_ctrl_new_fwnode_properties(), so I think 10 is a
correct value here.

With these small issues addressed,

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

>  	if (ret)
>  		return ret;
>  
> @@ -636,11 +645,11 @@ static int ov4689_initialize_controls(struct ov4689 *ov4689)
>  	v4l2_ctrl_new_std(handler, NULL, V4L2_CID_PIXEL_RATE, 0,
>  			  mode->pixel_rate, 1, mode->pixel_rate);
>  
> -	h_blank_def = mode->hts_def - mode->width;
> -	ctrl = v4l2_ctrl_new_std(handler, NULL, V4L2_CID_HBLANK, h_blank_def,
> -				 h_blank_def, 1, h_blank_def);
> -	if (ctrl)
> -		ctrl->flags |= V4L2_CTRL_FLAG_READ_ONLY;
> +	hblank_def = mode->hts_def - mode->width;
> +	hblank_min = mode->hts_min - mode->width;
> +	v4l2_ctrl_new_std(handler, &ov4689_ctrl_ops, V4L2_CID_HBLANK,
> +			  hblank_min, OV4689_HTS_MAX - mode->width,
> +			  OV4689_HTS_DIVIDER, hblank_def);
>  
>  	vblank_def = mode->vts_def - mode->height;
>  	v4l2_ctrl_new_std(handler, &ov4689_ctrl_ops, V4L2_CID_VBLANK,
  
Mikhail Rudenko Dec. 12, 2023, 12:37 p.m. UTC | #2
On 2023-12-12 at 00:08 +02, Laurent Pinchart <laurent.pinchart@ideasonboard.com> wrote:

> Hi Mikhail,
>
> Thank you for the patch.
>
> On Mon, Dec 11, 2023 at 08:50:13PM +0300, Mikhail Rudenko wrote:
>> Make horizontal blanking configurable. To do so, set HTS register
>> according to the requested horizontal blanking in ov4689_set_ctrl
>> instead of the register table. Default HTS value is not changed by
>> this patch. Minimal HTS value is found experimentally and corresponds
>> to 90 fps framerate at minimum vertical blanking. Real HTS value is
>> the register value multiplied by 4.
>>
>> Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
>> ---
>>  drivers/media/i2c/ov4689.c | 33 +++++++++++++++++++++------------
>>  1 file changed, 21 insertions(+), 12 deletions(-)
>>
>> diff --git a/drivers/media/i2c/ov4689.c b/drivers/media/i2c/ov4689.c
>> index 9fa06941a0e5..67d4004bdcfb 100644
>> --- a/drivers/media/i2c/ov4689.c
>> +++ b/drivers/media/i2c/ov4689.c
>> @@ -30,7 +30,6 @@
>>  #define OV4689_REG_EXPOSURE		CCI_REG24(0x3500)
>>  #define OV4689_EXPOSURE_MIN		4
>>  #define OV4689_EXPOSURE_STEP		1
>> -#define OV4689_VTS_MAX			0x7fff
>>
>>  #define OV4689_REG_GAIN			CCI_REG16(0x3508)
>>  #define OV4689_GAIN_STEP		1
>> @@ -41,6 +40,11 @@
>>  #define OV4689_TEST_PATTERN_DISABLE	0x0
>>
>>  #define OV4689_REG_VTS			CCI_REG16(0x380e)
>> +#define OV4689_VTS_MAX			0x7fff
>> +
>> +#define OV4689_REG_HTS			CCI_REG16(0x380c)
>> +#define OV4689_HTS_DIVIDER		4
>> +#define OV4689_HTS_MAX			0x7fff
>
> Could you move this just before REG_VTS to keep registers sorted by
> address ?

Ack, will fix in v2.

>>
>>  #define OV4689_LANES			4
>>  #define OV4689_XVCLK_FREQ		24000000
>> @@ -61,6 +65,7 @@ struct ov4689_mode {
>>  	u32 width;
>>  	u32 height;
>>  	u32 hts_def;
>> +	u32 hts_min;
>>  	u32 vts_def;
>>  	u32 exp_def;
>>  	u32 pixel_rate;
>> @@ -104,7 +109,7 @@ struct ov4689_gain_range {
>>
>>  /*
>>   * Xclk 24Mhz
>> - * max_framerate 30fps
>> + * max_framerate 90fps
>>   * mipi_datarate per lane 1008Mbps
>>   */
>>  static const struct cci_reg_sequence ov4689_2688x1520_regs[] = {
>> @@ -175,8 +180,6 @@ static const struct cci_reg_sequence ov4689_2688x1520_regs[] = {
>>  	/* Timing control */
>>  	{CCI_REG8(0x3801), 0x08}, /* H_CROP_START_L h_crop_start[7:0] = 0x08 */
>>  	{CCI_REG8(0x3805), 0x97}, /* H_CROP_END_L h_crop_end[7:0] = 0x97 */
>> -	{CCI_REG8(0x380c), 0x0a}, /* TIMING_HTS_H hts[14:8] = 0x0a */
>> -	{CCI_REG8(0x380d), 0x0e}, /* TIMING_HTS_L hts[7:0] = 0x0e */
>>  	{CCI_REG8(0x3811), 0x08}, /* H_WIN_OFF_L h_win_off[7:0] = 0x08*/
>>  	{CCI_REG8(0x3813), 0x04}, /* V_WIN_OFF_L v_win_off[7:0] = 0x04 */
>>  	{CCI_REG8(0x3819), 0x01}, /* VSYNC_END_L vsync_end_point[7:0] = 0x01 */
>> @@ -237,7 +240,8 @@ static const struct ov4689_mode supported_modes[] = {
>>  		.crop_top = 8,
>>  		.crop_left = 16,
>>  		.exp_def = 1536,
>> -		.hts_def = 4 * 2574,
>> +		.hts_def = 10296,
>> +		.hts_min = 3432,
>>  		.vts_def = 1554,
>>  		.pixel_rate = 480000000,
>>  		.reg_list = ov4689_2688x1520_regs,
>> @@ -596,6 +600,11 @@ static int ov4689_set_ctrl(struct v4l2_ctrl *ctrl)
>>  	case V4L2_CID_TEST_PATTERN:
>>  		ret = ov4689_enable_test_pattern(ov4689, val);
>>  		break;
>> +	case V4L2_CID_HBLANK:
>> +		cci_write(regmap, OV4689_REG_HTS,
>> +			  (val + ov4689->cur_mode->width) /
>> +			  OV4689_HTS_DIVIDER, &ret);
>> +		break;
>>  	default:
>>  		dev_warn(dev, "%s Unhandled id:0x%x, val:0x%x\n",
>>  			 __func__, ctrl->id, val);
>> @@ -618,13 +627,13 @@ static int ov4689_initialize_controls(struct ov4689 *ov4689)
>>  	struct v4l2_ctrl_handler *handler;
>>  	const struct ov4689_mode *mode;
>>  	s64 exposure_max, vblank_def;
>> +	s64 hblank_def, hblank_min;
>>  	struct v4l2_ctrl *ctrl;
>> -	s64 h_blank_def;
>>  	int ret;
>>
>>  	handler = &ov4689->ctrl_handler;
>>  	mode = ov4689->cur_mode;
>> -	ret = v4l2_ctrl_handler_init(handler, 10);
>> +	ret = v4l2_ctrl_handler_init(handler, 11);
>
> The HBLANK control already exists, you're only changing how it is
> initialized. I see 8 controls being created by the driver directly,
> plus 2 created by v4l2_ctrl_new_fwnode_properties(), so I think 10 is a
> correct value here.

Yes, will adjust here and in the further patches.

> With these small issues addressed,
>
> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
>
>>  	if (ret)
>>  		return ret;
>>
>> @@ -636,11 +645,11 @@ static int ov4689_initialize_controls(struct ov4689 *ov4689)
>>  	v4l2_ctrl_new_std(handler, NULL, V4L2_CID_PIXEL_RATE, 0,
>>  			  mode->pixel_rate, 1, mode->pixel_rate);
>>
>> -	h_blank_def = mode->hts_def - mode->width;
>> -	ctrl = v4l2_ctrl_new_std(handler, NULL, V4L2_CID_HBLANK, h_blank_def,
>> -				 h_blank_def, 1, h_blank_def);
>> -	if (ctrl)
>> -		ctrl->flags |= V4L2_CTRL_FLAG_READ_ONLY;
>> +	hblank_def = mode->hts_def - mode->width;
>> +	hblank_min = mode->hts_min - mode->width;
>> +	v4l2_ctrl_new_std(handler, &ov4689_ctrl_ops, V4L2_CID_HBLANK,
>> +			  hblank_min, OV4689_HTS_MAX - mode->width,
>> +			  OV4689_HTS_DIVIDER, hblank_def);
>>
>>  	vblank_def = mode->vts_def - mode->height;
>>  	v4l2_ctrl_new_std(handler, &ov4689_ctrl_ops, V4L2_CID_VBLANK,


--
Best regards,
Mikhail Rudenko
  

Patch

diff --git a/drivers/media/i2c/ov4689.c b/drivers/media/i2c/ov4689.c
index 9fa06941a0e5..67d4004bdcfb 100644
--- a/drivers/media/i2c/ov4689.c
+++ b/drivers/media/i2c/ov4689.c
@@ -30,7 +30,6 @@ 
 #define OV4689_REG_EXPOSURE		CCI_REG24(0x3500)
 #define OV4689_EXPOSURE_MIN		4
 #define OV4689_EXPOSURE_STEP		1
-#define OV4689_VTS_MAX			0x7fff
 
 #define OV4689_REG_GAIN			CCI_REG16(0x3508)
 #define OV4689_GAIN_STEP		1
@@ -41,6 +40,11 @@ 
 #define OV4689_TEST_PATTERN_DISABLE	0x0
 
 #define OV4689_REG_VTS			CCI_REG16(0x380e)
+#define OV4689_VTS_MAX			0x7fff
+
+#define OV4689_REG_HTS			CCI_REG16(0x380c)
+#define OV4689_HTS_DIVIDER		4
+#define OV4689_HTS_MAX			0x7fff
 
 #define OV4689_LANES			4
 #define OV4689_XVCLK_FREQ		24000000
@@ -61,6 +65,7 @@  struct ov4689_mode {
 	u32 width;
 	u32 height;
 	u32 hts_def;
+	u32 hts_min;
 	u32 vts_def;
 	u32 exp_def;
 	u32 pixel_rate;
@@ -104,7 +109,7 @@  struct ov4689_gain_range {
 
 /*
  * Xclk 24Mhz
- * max_framerate 30fps
+ * max_framerate 90fps
  * mipi_datarate per lane 1008Mbps
  */
 static const struct cci_reg_sequence ov4689_2688x1520_regs[] = {
@@ -175,8 +180,6 @@  static const struct cci_reg_sequence ov4689_2688x1520_regs[] = {
 	/* Timing control */
 	{CCI_REG8(0x3801), 0x08}, /* H_CROP_START_L h_crop_start[7:0] = 0x08 */
 	{CCI_REG8(0x3805), 0x97}, /* H_CROP_END_L h_crop_end[7:0] = 0x97 */
-	{CCI_REG8(0x380c), 0x0a}, /* TIMING_HTS_H hts[14:8] = 0x0a */
-	{CCI_REG8(0x380d), 0x0e}, /* TIMING_HTS_L hts[7:0] = 0x0e */
 	{CCI_REG8(0x3811), 0x08}, /* H_WIN_OFF_L h_win_off[7:0] = 0x08*/
 	{CCI_REG8(0x3813), 0x04}, /* V_WIN_OFF_L v_win_off[7:0] = 0x04 */
 	{CCI_REG8(0x3819), 0x01}, /* VSYNC_END_L vsync_end_point[7:0] = 0x01 */
@@ -237,7 +240,8 @@  static const struct ov4689_mode supported_modes[] = {
 		.crop_top = 8,
 		.crop_left = 16,
 		.exp_def = 1536,
-		.hts_def = 4 * 2574,
+		.hts_def = 10296,
+		.hts_min = 3432,
 		.vts_def = 1554,
 		.pixel_rate = 480000000,
 		.reg_list = ov4689_2688x1520_regs,
@@ -596,6 +600,11 @@  static int ov4689_set_ctrl(struct v4l2_ctrl *ctrl)
 	case V4L2_CID_TEST_PATTERN:
 		ret = ov4689_enable_test_pattern(ov4689, val);
 		break;
+	case V4L2_CID_HBLANK:
+		cci_write(regmap, OV4689_REG_HTS,
+			  (val + ov4689->cur_mode->width) /
+			  OV4689_HTS_DIVIDER, &ret);
+		break;
 	default:
 		dev_warn(dev, "%s Unhandled id:0x%x, val:0x%x\n",
 			 __func__, ctrl->id, val);
@@ -618,13 +627,13 @@  static int ov4689_initialize_controls(struct ov4689 *ov4689)
 	struct v4l2_ctrl_handler *handler;
 	const struct ov4689_mode *mode;
 	s64 exposure_max, vblank_def;
+	s64 hblank_def, hblank_min;
 	struct v4l2_ctrl *ctrl;
-	s64 h_blank_def;
 	int ret;
 
 	handler = &ov4689->ctrl_handler;
 	mode = ov4689->cur_mode;
-	ret = v4l2_ctrl_handler_init(handler, 10);
+	ret = v4l2_ctrl_handler_init(handler, 11);
 	if (ret)
 		return ret;
 
@@ -636,11 +645,11 @@  static int ov4689_initialize_controls(struct ov4689 *ov4689)
 	v4l2_ctrl_new_std(handler, NULL, V4L2_CID_PIXEL_RATE, 0,
 			  mode->pixel_rate, 1, mode->pixel_rate);
 
-	h_blank_def = mode->hts_def - mode->width;
-	ctrl = v4l2_ctrl_new_std(handler, NULL, V4L2_CID_HBLANK, h_blank_def,
-				 h_blank_def, 1, h_blank_def);
-	if (ctrl)
-		ctrl->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+	hblank_def = mode->hts_def - mode->width;
+	hblank_min = mode->hts_min - mode->width;
+	v4l2_ctrl_new_std(handler, &ov4689_ctrl_ops, V4L2_CID_HBLANK,
+			  hblank_min, OV4689_HTS_MAX - mode->width,
+			  OV4689_HTS_DIVIDER, hblank_def);
 
 	vblank_def = mode->vts_def - mode->height;
 	v4l2_ctrl_new_std(handler, &ov4689_ctrl_ops, V4L2_CID_VBLANK,