diff mbox series

[net-next,v3,08/13] net: phy: at803x: move specific at8031 WOL bits to dedicated function

Message ID 20231206235728.6985-9-ansuelsmth@gmail.com
State New
Headers
Series net: phy: at803x: cleanup |

Commit Message

Christian Marangi Dec. 6, 2023, 11:57 p.m. UTC 
  Move specific at8031 WOL enable/disable to dedicated function to make
at803x_set_wol more generic.

This is needed in preparation for PHY driver split as qca8081 share the
same function to toggle WOL settings.

In this new implementation WOL module in at8031 is enabled after the
generic interrupt is setup. This should not cause any problem as the
WOL_INT has a separate implementation and only relay on MAC bits.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
 drivers/net/phy/at803x.c | 42 ++++++++++++++++++++++++----------------
 1 file changed, 25 insertions(+), 17 deletions(-)
diff mbox series

Patch

diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c
index 02ac71f98466..2de7a59c0faa 100644
--- a/drivers/net/phy/at803x.c
+++ b/drivers/net/phy/at803x.c
@@ -466,27 +466,11 @@  static int at803x_set_wol(struct phy_device *phydev,
 			phy_write_mmd(phydev, MDIO_MMD_PCS, offsets[i],
 				      mac[(i * 2) + 1] | (mac[(i * 2)] << 8));
 
-		/* Enable WOL function for 1588 */
-		if (phydev->drv->phy_id == ATH8031_PHY_ID) {
-			ret = phy_modify_mmd(phydev, MDIO_MMD_PCS,
-					     AT803X_PHY_MMD3_WOL_CTRL,
-					     0, AT803X_WOL_EN);
-			if (ret)
-				return ret;
-		}
 		/* Enable WOL interrupt */
 		ret = phy_modify(phydev, AT803X_INTR_ENABLE, 0, AT803X_INTR_ENABLE_WOL);
 		if (ret)
 			return ret;
 	} else {
-		/* Disable WoL function for 1588 */
-		if (phydev->drv->phy_id == ATH8031_PHY_ID) {
-			ret = phy_modify_mmd(phydev, MDIO_MMD_PCS,
-					     AT803X_PHY_MMD3_WOL_CTRL,
-					     AT803X_WOL_EN, 0);
-			if (ret)
-				return ret;
-		}
 		/* Disable WOL interrupt */
 		ret = phy_modify(phydev, AT803X_INTR_ENABLE, AT803X_INTR_ENABLE_WOL, 0);
 		if (ret)
@@ -1611,6 +1595,30 @@  static int at8031_config_init(struct phy_device *phydev)
 	return at803x_config_init(phydev);
 }
 
+static int at8031_set_wol(struct phy_device *phydev,
+			  struct ethtool_wolinfo *wol)
+{
+	int ret;
+
+	/* First setup MAC address and enable WOL interrupt */
+	ret = at803x_set_wol(phydev, wol);
+	if (ret)
+		return ret;
+
+	if (wol->wolopts & WAKE_MAGIC)
+		/* Enable WOL function for 1588 */
+		ret = phy_modify_mmd(phydev, MDIO_MMD_PCS,
+				     AT803X_PHY_MMD3_WOL_CTRL,
+				     0, AT803X_WOL_EN);
+	else
+		/* Disable WoL function for 1588 */
+		ret = phy_modify_mmd(phydev, MDIO_MMD_PCS,
+				     AT803X_PHY_MMD3_WOL_CTRL,
+				     AT803X_WOL_EN, 0);
+
+	return ret;
+}
+
 static int qca83xx_config_init(struct phy_device *phydev)
 {
 	u8 switch_revision;
@@ -2123,7 +2131,7 @@  static struct phy_driver at803x_driver[] = {
 	.config_init		= at8031_config_init,
 	.config_aneg		= at803x_config_aneg,
 	.soft_reset		= genphy_soft_reset,
-	.set_wol		= at803x_set_wol,
+	.set_wol		= at8031_set_wol,
 	.get_wol		= at803x_get_wol,
 	.suspend		= at803x_suspend,
 	.resume			= at803x_resume,