[v4,1/6] tty: serial: amba: cleanup whitespace
Commit Message
Fix whitespace in include/linux/amba/serial.h to match current kernel
coding standards. Fixes about:
- CHECK: spaces preferred around that '|' (ctx:VxV)
- ERROR: code indent should use tabs where possible
- WARNING: Unnecessary space before function pointer arguments
- WARNING: please, no spaces at the start of a line
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
---
include/linux/amba/serial.h | 28 ++++++++++++++--------------
1 file changed, 14 insertions(+), 14 deletions(-)
@@ -75,10 +75,10 @@
#define UART011_DR_PE (1 << 9)
#define UART011_DR_FE (1 << 8)
-#define UART01x_RSR_OE 0x08
-#define UART01x_RSR_BE 0x04
-#define UART01x_RSR_PE 0x02
-#define UART01x_RSR_FE 0x01
+#define UART01x_RSR_OE 0x08
+#define UART01x_RSR_BE 0x04
+#define UART01x_RSR_PE 0x02
+#define UART01x_RSR_FE 0x01
#define UART011_FR_RI 0x100
#define UART011_FR_TXFE 0x080
@@ -86,9 +86,9 @@
#define UART01x_FR_TXFF 0x020
#define UART01x_FR_RXFE 0x010
#define UART01x_FR_BUSY 0x008
-#define UART01x_FR_DCD 0x004
-#define UART01x_FR_DSR 0x002
-#define UART01x_FR_CTS 0x001
+#define UART01x_FR_DCD 0x004
+#define UART01x_FR_DSR 0x002
+#define UART01x_FR_CTS 0x001
#define UART01x_FR_TMSK (UART01x_FR_TXFF + UART01x_FR_BUSY)
/*
@@ -110,14 +110,14 @@
#define UART011_CR_TXE 0x0100 /* transmit enable */
#define UART011_CR_LBE 0x0080 /* loopback enable */
#define UART010_CR_RTIE 0x0040
-#define UART010_CR_TIE 0x0020
-#define UART010_CR_RIE 0x0010
+#define UART010_CR_TIE 0x0020
+#define UART010_CR_RIE 0x0010
#define UART010_CR_MSIE 0x0008
#define ST_UART011_CR_OVSFACT 0x0008 /* Oversampling factor */
#define UART01x_CR_IIRLP 0x0004 /* SIR low power mode */
#define UART01x_CR_SIREN 0x0002 /* SIR enable */
#define UART01x_CR_UARTEN 0x0001 /* UART enable */
-
+
#define UART011_LCRH_SPS 0x80
#define UART01x_LCRH_WLEN_8 0x60
#define UART01x_LCRH_WLEN_7 0x40
@@ -203,8 +203,8 @@
#define UART011_TXDMAE (1 << 1) /* enable transmit dma */
#define UART011_RXDMAE (1 << 0) /* enable receive dma */
-#define UART01x_RSR_ANY (UART01x_RSR_OE|UART01x_RSR_BE|UART01x_RSR_PE|UART01x_RSR_FE)
-#define UART01x_FR_MODEM_ANY (UART01x_FR_DCD|UART01x_FR_DSR|UART01x_FR_CTS)
+#define UART01x_RSR_ANY (UART01x_RSR_OE | UART01x_RSR_BE | UART01x_RSR_PE | UART01x_RSR_FE)
+#define UART01x_FR_MODEM_ANY (UART01x_FR_DCD | UART01x_FR_DSR | UART01x_FR_CTS)
#ifndef __ASSEMBLY__
struct amba_device; /* in uncompress this is included but amba/bus.h is not */
@@ -220,8 +220,8 @@ struct amba_pl011_data {
bool dma_rx_poll_enable;
unsigned int dma_rx_poll_rate;
unsigned int dma_rx_poll_timeout;
- void (*init) (void);
- void (*exit) (void);
+ void (*init)(void);
+ void (*exit)(void);
};
#endif