For qca8084 chip, there are GCC, TLMM and security control
modules besides the PHY, these moudles are accessed with 32
bits value, which has the special MDIO sequences to read or
write this 32bit register.
There are initial configurations needed to make qca8084 PHY
probeable, and the PHY address of qca8084 can also be customized
before creating the PHY device on MDIO bus register, all these
configurations are located in switch modules that are accessed
by the 32bit register.
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
---
drivers/net/mdio/mdio-ipq4019.c | 74 +++++++++++++++++++++++++++++++++
1 file changed, 74 insertions(+)
@@ -53,6 +53,14 @@
#define CMN_PLL_POWER_ON_AND_RESET 0x780
#define CMN_ANA_EN_SW_RSTN BIT(6)
+/* QCA8084 includes the PHY chip, GCC/TLMM and the control modules,
+ * except for the PHY register, other registers are accessed by MDIO bus
+ * with 32bit value, which has the special MDIO sequences to access the
+ * switch modules register.
+ */
+#define IPQ_HIGH_ADDR_PREFIX 0x18
+#define IPQ_LOW_ADDR_PREFIX 0x10
+
enum mdio_clk_id {
MDIO_CLK_MDIO_AHB,
MDIO_CLK_UNIPHY0_AHB,
@@ -243,6 +251,72 @@ static int ipq4019_mdio_write_c22(struct mii_bus *bus, int mii_id, int regnum,
return 0;
}
+static inline void split_addr(u32 regaddr, u16 *r1, u16 *r2, u16 *page, u16 *sw_addr)
+{
+ *r1 = regaddr & 0x1c;
+
+ regaddr >>= 5;
+ *r2 = regaddr & 0x7;
+
+ regaddr >>= 3;
+ *page = regaddr & 0xffff;
+
+ regaddr >>= 16;
+ *sw_addr = regaddr & 0xff;
+}
+
+static int qca8084_set_page(struct mii_bus *bus, u16 sw_addr, u16 page)
+{
+ return bus->write(bus, IPQ_HIGH_ADDR_PREFIX | (sw_addr >> 5), sw_addr & 0x1f, page);
+}
+
+static int qca8084_mii_read(struct mii_bus *bus, u16 addr, u16 reg, u32 *val)
+{
+ int ret, data;
+
+ ret = bus->read(bus, addr, reg);
+ if (ret >= 0) {
+ data = ret;
+
+ ret = bus->read(bus, addr, reg | BIT(1));
+ if (ret >= 0)
+ *val = data | ret << 16;
+ }
+
+ return ret < 0 ? ret : 0;
+}
+
+static int qca8084_mii_write(struct mii_bus *bus, u16 addr, u16 reg, u32 val)
+{
+ int ret;
+
+ ret = bus->write(bus, addr, reg, lower_16_bits(val));
+ if (!ret)
+ ret = bus->write(bus, addr, reg | BIT(1), upper_16_bits(val));
+
+ return ret;
+}
+
+static int qca8084_modify(struct mii_bus *bus, u32 regaddr, u32 clear, u32 set)
+{
+ u16 reg, addr, page, sw_addr;
+ u32 val;
+ int ret;
+
+ split_addr(regaddr, ®, &addr, &page, &sw_addr);
+ ret = qca8084_set_page(bus, sw_addr, page);
+ if (ret < 0)
+ return ret;
+
+ ret = qca8084_mii_read(bus, IPQ_LOW_ADDR_PREFIX | addr, reg, &val);
+ if (ret < 0)
+ return ret;
+
+ val &= ~clear;
+ val |= set;
+ return qca8084_mii_write(bus, IPQ_LOW_ADDR_PREFIX | addr, reg, val);
+};
+
/* For the CMN PLL block, the reference clock can be configured according to
* the device tree property "cmn_ref_clk", the internal 48MHZ is used by default
* on the ipq533 platform.