@@ -203,6 +203,9 @@ struct edp_panel_entry {
/** @name: Name of this panel (for printing to logs). */
const char *name;
+
+ /** @override_edid_mode: Override the mode obtained by edid. */
+ const struct drm_display_mode *override_edid_mode;
};
struct panel_edp {
@@ -301,6 +304,25 @@ static unsigned int panel_edp_get_display_modes(struct panel_edp *panel,
return num;
}
+static int panel_edp_override_edid_mode(struct panel_edp *panel,
+ struct drm_connector *connector,
+ const struct drm_display_mode *override_mode)
+{
+ struct drm_display_mode *mode;
+
+ mode = drm_mode_duplicate(connector->dev, override_mode);
+ if (mode) {
+ mode->type |= DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
+ drm_mode_set_name(mode);
+ drm_mode_probed_add(connector, mode);
+ return 1;
+ }
+
+ dev_err(panel->base.dev, "failed to add additional mode\n");
+
+ return 0;
+}
+
static int panel_edp_get_non_edid_modes(struct panel_edp *panel,
struct drm_connector *connector)
{
@@ -568,6 +590,9 @@ static int panel_edp_get_modes(struct drm_panel *panel,
{
struct panel_edp *p = to_panel_edp(panel);
int num = 0;
+ bool has_override_edid_mode = p->detected_panel &&
+ p->detected_panel != ERR_PTR(-EINVAL) &&
+ p->detected_panel->override_edid_mode;
/* probe EDID if a DDC bus is available */
if (p->ddc) {
@@ -575,9 +600,18 @@ static int panel_edp_get_modes(struct drm_panel *panel,
if (!p->edid)
p->edid = drm_get_edid(connector, p->ddc);
-
- if (p->edid)
- num += drm_add_edid_modes(connector, p->edid);
+ if (p->edid) {
+ if (has_override_edid_mode) {
+ /*
+ * override_edid_mode is specified. Use
+ * override_edid_mode instead of from edid.
+ */
+ num += panel_edp_override_edid_mode(p, connector,
+ p->detected_panel->override_edid_mode);
+ } else {
+ num += drm_add_edid_modes(connector, p->edid);
+ }
+ }
pm_runtime_mark_last_busy(panel->dev);
pm_runtime_put_autosuspend(panel->dev);
@@ -950,6 +984,19 @@ static const struct panel_desc auo_b101ean01 = {
},
};
+static const struct drm_display_mode auo_b116xa3_mode = {
+ .clock = 70589,
+ .hdisplay = 1366,
+ .hsync_start = 1366 + 40,
+ .hsync_end = 1366 + 40 + 40,
+ .htotal = 1366 + 40 + 40 + 32,
+ .vdisplay = 768,
+ .vsync_start = 768 + 10,
+ .vsync_end = 768 + 10 + 12,
+ .vtotal = 768 + 10 + 12 + 6,
+ .flags = DRM_MODE_FLAG_NVSYNC | DRM_MODE_FLAG_NHSYNC,
+};
+
static const struct drm_display_mode auo_b116xak01_mode = {
.clock = 69300,
.hdisplay = 1366,
@@ -1878,6 +1925,15 @@ static const struct panel_delay delay_200_150_e200 = {
.delay = _delay \
}
+#define EDP_PANEL_ENTRY2(vend_chr_0, vend_chr_1, vend_chr_2, product_id, _delay, _name, _mode) \
+{ \
+ .name = _name, \
+ .panel_id = drm_edid_encode_panel_id(vend_chr_0, vend_chr_1, vend_chr_2, \
+ product_id), \
+ .delay = _delay, \
+ .override_edid_mode = _mode \
+}
+
/*
* This table is used to figure out power sequencing delays for panels that
* are detected by EDID. Entries here may point to entries in the
@@ -1895,9 +1951,11 @@ static const struct edp_panel_entry edp_panels[] = {
EDP_PANEL_ENTRY('A', 'U', 'O', 0x239b, &delay_200_500_e50, "B116XAN06.1"),
EDP_PANEL_ENTRY('A', 'U', 'O', 0x255c, &delay_200_500_e50, "B116XTN02.5"),
EDP_PANEL_ENTRY('A', 'U', 'O', 0x403d, &delay_200_500_e50, "B140HAN04.0"),
- EDP_PANEL_ENTRY('A', 'U', 'O', 0x405c, &auo_b116xak01.delay, "B116XAK01.0"),
+ EDP_PANEL_ENTRY2('A', 'U', 'O', 0x405c, &auo_b116xak01.delay, "B116XAK01.0",
+ &auo_b116xa3_mode),
EDP_PANEL_ENTRY('A', 'U', 'O', 0x582d, &delay_200_500_e50, "B133UAN01.0"),
- EDP_PANEL_ENTRY('A', 'U', 'O', 0x615c, &delay_200_500_e50, "B116XAN06.1"),
+ EDP_PANEL_ENTRY2('A', 'U', 'O', 0x615c, &delay_200_500_e50, "B116XAN06.1",
+ &auo_b116xa3_mode),
EDP_PANEL_ENTRY('A', 'U', 'O', 0x635c, &delay_200_500_e50, "B116XAN06.3"),
EDP_PANEL_ENTRY('A', 'U', 'O', 0x639c, &delay_200_500_e50, "B140HAK02.7"),
EDP_PANEL_ENTRY('A', 'U', 'O', 0x8594, &delay_200_500_e50, "B133UAN01.0"),