[1/1] PCI: Use FIELD_PREP() and remove *_SHIFT defines

Message ID 20231027083811.9200-1-ilpo.jarvinen@linux.intel.com
State New
Headers
Series [1/1] PCI: Use FIELD_PREP() and remove *_SHIFT defines |

Commit Message

Ilpo Järvinen Oct. 27, 2023, 8:38 a.m. UTC
  Instead of open-coded masking and shifting with PCI_CONF1_* bitfields,
use GENMASK() and FIELD_PREP(), and then remove the *_SHIFT defines
that are no longer needed.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
---

 drivers/pci/pci.h | 23 ++++++++++-------------
 1 file changed, 10 insertions(+), 13 deletions(-)
  

Comments

Bjorn Helgaas Oct. 31, 2023, 8:03 p.m. UTC | #1
On Fri, Oct 27, 2023 at 11:38:11AM +0300, Ilpo Järvinen wrote:
> Instead of open-coded masking and shifting with PCI_CONF1_* bitfields,
> use GENMASK() and FIELD_PREP(), and then remove the *_SHIFT defines
> that are no longer needed.
> 
> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
> ---
> 
>  drivers/pci/pci.h | 23 ++++++++++-------------
>  1 file changed, 10 insertions(+), 13 deletions(-)
> 
> diff --git a/drivers/pci/pci.h b/drivers/pci/pci.h
> index 39a8932dc340..31da9fde8aca 100644
> --- a/drivers/pci/pci.h
> +++ b/drivers/pci/pci.h
> @@ -2,6 +2,8 @@
>  #ifndef DRIVERS_PCI_H
>  #define DRIVERS_PCI_H
>  
> +#include <linux/bitfield.h>
> +#include <linux/bits.h>
>  #include <linux/pci.h>
>  
>  /* Number of possible devfns: 0.0 to 1f.7 inclusive */
> @@ -797,19 +799,15 @@ static inline pci_power_t mid_pci_get_power_state(struct pci_dev *pdev)
>   * Section 3.2.2.3.2, Figure 3-2, p. 50.
>   */
>  
> -#define PCI_CONF1_BUS_SHIFT	16 /* Bus number */
> -#define PCI_CONF1_DEV_SHIFT	11 /* Device number */
> -#define PCI_CONF1_FUNC_SHIFT	8  /* Function number */
> -
> -#define PCI_CONF1_BUS_MASK	0xff
> -#define PCI_CONF1_DEV_MASK	0x1f
> -#define PCI_CONF1_FUNC_MASK	0x7
> +#define PCI_CONF1_BUS_MASK	GENMASK(23, 16)
> +#define PCI_CONF1_DEV_MASK	GENMASK(15, 11)
> +#define PCI_CONF1_FUNC_MASK	GENMASK(10, 8)
>  #define PCI_CONF1_REG_MASK	0xfc /* Limit aligned offset to a maximum of 256B */
>  
>  #define PCI_CONF1_ENABLE	BIT(31)
> -#define PCI_CONF1_BUS(x)	(((x) & PCI_CONF1_BUS_MASK) << PCI_CONF1_BUS_SHIFT)
> -#define PCI_CONF1_DEV(x)	(((x) & PCI_CONF1_DEV_MASK) << PCI_CONF1_DEV_SHIFT)
> -#define PCI_CONF1_FUNC(x)	(((x) & PCI_CONF1_FUNC_MASK) << PCI_CONF1_FUNC_SHIFT)
> +#define PCI_CONF1_BUS(x)	FIELD_PREP(PCI_CONF1_BUS_MASK, (x))
> +#define PCI_CONF1_DEV(x)	FIELD_PREP(PCI_CONF1_DEV_MASK, (x))
> +#define PCI_CONF1_FUNC(x)	FIELD_PREP(PCI_CONF1_FUNC_MASK, (x))
>  #define PCI_CONF1_REG(x)	((x) & PCI_CONF1_REG_MASK)

I love getting rid of the _SHIFT #defines.

I'm a dinosaur and haven't been completely converted to the wonders of
GENMASK yet.  PCI_CONF1_ADDRESS is the only user of PCI_CONF1_BUS etc,
so I think this would be simpler overall:

  #define PCI_CONF1_BUS  0x00ff0000
  #define PCI_CONF1_DEV  0x0000f800
  #define PCI_CONF1_FUNC 0x00000700
  #define PCI_CONF1_REG  0x000000ff

  #define PCI_CONF1_ADDRESS(bus, dev, func, reg) \
    (FIELD_PREP(PCI_CONF1_BUS, (bus)) | \
     FIELD_PREP(PCI_CONF1_DEV, (dev)) | \
     FIELD_PREP(PCI_CONF1_FUNC, (func)) | \
     FIELD_PREP(PCI_CONF1_REG, (reg & ~0x3)))

The v6.7 merge window just opened, and I won't start merging v6.8
material until v6.7-rc1 (probably Nov 12), so no hurry on this.

Bjorn
  
Ilpo Järvinen Nov. 3, 2023, 1:10 p.m. UTC | #2
On Tue, 31 Oct 2023, Bjorn Helgaas wrote:
> On Fri, Oct 27, 2023 at 11:38:11AM +0300, Ilpo Järvinen wrote:
> > Instead of open-coded masking and shifting with PCI_CONF1_* bitfields,
> > use GENMASK() and FIELD_PREP(), and then remove the *_SHIFT defines
> > that are no longer needed.

> > @@ -797,19 +799,15 @@ static inline pci_power_t mid_pci_get_power_state(struct pci_dev *pdev)
> >   * Section 3.2.2.3.2, Figure 3-2, p. 50.
> >   */
> >  
> > -#define PCI_CONF1_BUS_SHIFT	16 /* Bus number */
> > -#define PCI_CONF1_DEV_SHIFT	11 /* Device number */
> > -#define PCI_CONF1_FUNC_SHIFT	8  /* Function number */
> > -
> > -#define PCI_CONF1_BUS_MASK	0xff
> > -#define PCI_CONF1_DEV_MASK	0x1f
> > -#define PCI_CONF1_FUNC_MASK	0x7
> > +#define PCI_CONF1_BUS_MASK	GENMASK(23, 16)
> > +#define PCI_CONF1_DEV_MASK	GENMASK(15, 11)
> > +#define PCI_CONF1_FUNC_MASK	GENMASK(10, 8)
> >  #define PCI_CONF1_REG_MASK	0xfc /* Limit aligned offset to a maximum of 256B */
> >  
> >  #define PCI_CONF1_ENABLE	BIT(31)
> > -#define PCI_CONF1_BUS(x)	(((x) & PCI_CONF1_BUS_MASK) << PCI_CONF1_BUS_SHIFT)
> > -#define PCI_CONF1_DEV(x)	(((x) & PCI_CONF1_DEV_MASK) << PCI_CONF1_DEV_SHIFT)
> > -#define PCI_CONF1_FUNC(x)	(((x) & PCI_CONF1_FUNC_MASK) << PCI_CONF1_FUNC_SHIFT)
> > +#define PCI_CONF1_BUS(x)	FIELD_PREP(PCI_CONF1_BUS_MASK, (x))
> > +#define PCI_CONF1_DEV(x)	FIELD_PREP(PCI_CONF1_DEV_MASK, (x))
> > +#define PCI_CONF1_FUNC(x)	FIELD_PREP(PCI_CONF1_FUNC_MASK, (x))
> >  #define PCI_CONF1_REG(x)	((x) & PCI_CONF1_REG_MASK)
> 
> I love getting rid of the _SHIFT #defines.
>
> I'm a dinosaur and haven't been completely converted to the wonders of
> GENMASK yet.

Okay but would it convince even "a dinosaur" like you :-) if you imagine
a Bit Location column in some spec which says:
	23:16

GENMASK just happens to mystically repeat those two numbers:
	GENMASK(23, 16)

Pretty magic, isn't it?

> PCI_CONF1_ADDRESS is the only user of PCI_CONF1_BUS etc,
> so I think this would be simpler overall:
> 
>   #define PCI_CONF1_BUS  0x00ff0000
>   #define PCI_CONF1_DEV  0x0000f800
>   #define PCI_CONF1_FUNC 0x00000700
>   #define PCI_CONF1_REG  0x000000ff
> 
>   #define PCI_CONF1_ADDRESS(bus, dev, func, reg) \
>     (FIELD_PREP(PCI_CONF1_BUS, (bus)) | \
>      FIELD_PREP(PCI_CONF1_DEV, (dev)) | \
>      FIELD_PREP(PCI_CONF1_FUNC, (func)) | \
>      FIELD_PREP(PCI_CONF1_REG, (reg & ~0x3)))

Yes, it makes sense to remove the extra layer.

One additional thing, I just noticed lots of arch/ code is duplicating 
this calculation so perhaps this should also be moved outside of 
drivers/pci/ into include/linux/pci.h ? (Not in the same patch.)

> The v6.7 merge window just opened, and I won't start merging v6.8
> material until v6.7-rc1 (probably Nov 12), so no hurry on this.

Yes I knew I was sending it quite late because I tried to meet your 
request in getting it all done in the same merge window (which I 
obviously failed but it isn't the end of the world).
  
Ilpo Järvinen Nov. 3, 2023, 2:07 p.m. UTC | #3
On Fri, 3 Nov 2023, Ilpo Järvinen wrote:

> On Tue, 31 Oct 2023, Bjorn Helgaas wrote:
> > On Fri, Oct 27, 2023 at 11:38:11AM +0300, Ilpo Järvinen wrote:
> > > Instead of open-coded masking and shifting with PCI_CONF1_* bitfields,
> > > use GENMASK() and FIELD_PREP(), and then remove the *_SHIFT defines
> > > that are no longer needed.
> 
> > > @@ -797,19 +799,15 @@ static inline pci_power_t mid_pci_get_power_state(struct pci_dev *pdev)
> > >   * Section 3.2.2.3.2, Figure 3-2, p. 50.
> > >   */
> > >  
> > > -#define PCI_CONF1_BUS_SHIFT	16 /* Bus number */
> > > -#define PCI_CONF1_DEV_SHIFT	11 /* Device number */
> > > -#define PCI_CONF1_FUNC_SHIFT	8  /* Function number */
> > > -
> > > -#define PCI_CONF1_BUS_MASK	0xff
> > > -#define PCI_CONF1_DEV_MASK	0x1f
> > > -#define PCI_CONF1_FUNC_MASK	0x7
> > > +#define PCI_CONF1_BUS_MASK	GENMASK(23, 16)
> > > +#define PCI_CONF1_DEV_MASK	GENMASK(15, 11)
> > > +#define PCI_CONF1_FUNC_MASK	GENMASK(10, 8)
> > >  #define PCI_CONF1_REG_MASK	0xfc /* Limit aligned offset to a maximum of 256B */
> > >  
> > >  #define PCI_CONF1_ENABLE	BIT(31)
> > > -#define PCI_CONF1_BUS(x)	(((x) & PCI_CONF1_BUS_MASK) << PCI_CONF1_BUS_SHIFT)
> > > -#define PCI_CONF1_DEV(x)	(((x) & PCI_CONF1_DEV_MASK) << PCI_CONF1_DEV_SHIFT)
> > > -#define PCI_CONF1_FUNC(x)	(((x) & PCI_CONF1_FUNC_MASK) << PCI_CONF1_FUNC_SHIFT)
> > > +#define PCI_CONF1_BUS(x)	FIELD_PREP(PCI_CONF1_BUS_MASK, (x))
> > > +#define PCI_CONF1_DEV(x)	FIELD_PREP(PCI_CONF1_DEV_MASK, (x))
> > > +#define PCI_CONF1_FUNC(x)	FIELD_PREP(PCI_CONF1_FUNC_MASK, (x))
> > >  #define PCI_CONF1_REG(x)	((x) & PCI_CONF1_REG_MASK)
> > 
> > I love getting rid of the _SHIFT #defines.
> >
> > I'm a dinosaur and haven't been completely converted to the wonders of
> > GENMASK yet.
> 
> Okay but would it convince even "a dinosaur" like you :-) if you imagine
> a Bit Location column in some spec which says:
> 	23:16
> 
> GENMASK just happens to mystically repeat those two numbers:
> 	GENMASK(23, 16)
> 
> Pretty magic, isn't it?
> 
> > PCI_CONF1_ADDRESS is the only user of PCI_CONF1_BUS etc,
> > so I think this would be simpler overall:
> > 
> >   #define PCI_CONF1_BUS  0x00ff0000
> >   #define PCI_CONF1_DEV  0x0000f800
> >   #define PCI_CONF1_FUNC 0x00000700
> >   #define PCI_CONF1_REG  0x000000ff
> > 
> >   #define PCI_CONF1_ADDRESS(bus, dev, func, reg) \
> >     (FIELD_PREP(PCI_CONF1_BUS, (bus)) | \
> >      FIELD_PREP(PCI_CONF1_DEV, (dev)) | \
> >      FIELD_PREP(PCI_CONF1_FUNC, (func)) | \
> >      FIELD_PREP(PCI_CONF1_REG, (reg & ~0x3)))

This ended up not working, because FIELD_PREP() detects ext regs not 
fitting into PCI_CONF1_REG:
	FIELD_PREP(PCI_CONF1_REG, (reg) & ~0x3)

There are two partially overlapping things here when it comes to reg 
(addressing side and parameter input side):

#define PCI_CONF1_REG_ADDR	0x000000ff
// for PCI_CONF1_EXT_ADDRESS:
#define PCI_CONF1_EXT_REG_ADDR	0x0f000000

/* PCI Config register (parameter input side) */
#define PCI_CONF1_REG		0x0fc
#define PCI_CONF1_EXT_REG	0xf00

Would those 4 defines be acceptable? Or should I mark the input side with
_IN or use different prefix for the defines?

> Yes, it makes sense to remove the extra layer.
> 
> One additional thing, I just noticed lots of arch/ code is duplicating 
> this calculation so perhaps this should also be moved outside of 
> drivers/pci/ into include/linux/pci.h ? (Not in the same patch.)

I also noticed you took PCI_CONF1_ENABLE away from PCI_CONF1_ADDRESS(),
did you intend for it to be moved at the caller site?

Moving it outside of PCI_CONF1_ADDRESS() would certainly help reusing this 
code as notall arch code wants PCI_CONF1_ENABLE I think.

> > The v6.7 merge window just opened, and I won't start merging v6.8
> > material until v6.7-rc1 (probably Nov 12), so no hurry on this.
> 
> Yes I knew I was sending it quite late because I tried to meet your 
> request in getting it all done in the same merge window (which I 
> obviously failed but it isn't the end of the world).
> 
>
  
Bjorn Helgaas Nov. 3, 2023, 3:51 p.m. UTC | #4
On Fri, Nov 03, 2023 at 04:07:19PM +0200, Ilpo Järvinen wrote:
> On Fri, 3 Nov 2023, Ilpo Järvinen wrote:
> 
> > On Tue, 31 Oct 2023, Bjorn Helgaas wrote:
> > > On Fri, Oct 27, 2023 at 11:38:11AM +0300, Ilpo Järvinen wrote:
> > > > Instead of open-coded masking and shifting with PCI_CONF1_* bitfields,
> > > > use GENMASK() and FIELD_PREP(), and then remove the *_SHIFT defines
> > > > that are no longer needed.
> > 
> > > > @@ -797,19 +799,15 @@ static inline pci_power_t mid_pci_get_power_state(struct pci_dev *pdev)
> > > >   * Section 3.2.2.3.2, Figure 3-2, p. 50.
> > > >   */
> > > >  
> > > > -#define PCI_CONF1_BUS_SHIFT	16 /* Bus number */
> > > > -#define PCI_CONF1_DEV_SHIFT	11 /* Device number */
> > > > -#define PCI_CONF1_FUNC_SHIFT	8  /* Function number */
> > > > -
> > > > -#define PCI_CONF1_BUS_MASK	0xff
> > > > -#define PCI_CONF1_DEV_MASK	0x1f
> > > > -#define PCI_CONF1_FUNC_MASK	0x7
> > > > +#define PCI_CONF1_BUS_MASK	GENMASK(23, 16)
> > > > +#define PCI_CONF1_DEV_MASK	GENMASK(15, 11)
> > > > +#define PCI_CONF1_FUNC_MASK	GENMASK(10, 8)
> > > >  #define PCI_CONF1_REG_MASK	0xfc /* Limit aligned offset to a maximum of 256B */
> > > >  
> > > >  #define PCI_CONF1_ENABLE	BIT(31)
> > > > -#define PCI_CONF1_BUS(x)	(((x) & PCI_CONF1_BUS_MASK) << PCI_CONF1_BUS_SHIFT)
> > > > -#define PCI_CONF1_DEV(x)	(((x) & PCI_CONF1_DEV_MASK) << PCI_CONF1_DEV_SHIFT)
> > > > -#define PCI_CONF1_FUNC(x)	(((x) & PCI_CONF1_FUNC_MASK) << PCI_CONF1_FUNC_SHIFT)
> > > > +#define PCI_CONF1_BUS(x)	FIELD_PREP(PCI_CONF1_BUS_MASK, (x))
> > > > +#define PCI_CONF1_DEV(x)	FIELD_PREP(PCI_CONF1_DEV_MASK, (x))
> > > > +#define PCI_CONF1_FUNC(x)	FIELD_PREP(PCI_CONF1_FUNC_MASK, (x))
> > > >  #define PCI_CONF1_REG(x)	((x) & PCI_CONF1_REG_MASK)
> > > 
> > > I love getting rid of the _SHIFT #defines.
> > >
> > > I'm a dinosaur and haven't been completely converted to the wonders of
> > > GENMASK yet.
> > 
> > Okay but would it convince even "a dinosaur" like you :-) if you imagine
> > a Bit Location column in some spec which says:
> > 	23:16
> > 
> > GENMASK just happens to mystically repeat those two numbers:
> > 	GENMASK(23, 16)
> > 
> > Pretty magic, isn't it?
> > 
> > > PCI_CONF1_ADDRESS is the only user of PCI_CONF1_BUS etc,
> > > so I think this would be simpler overall:
> > > 
> > >   #define PCI_CONF1_BUS  0x00ff0000
> > >   #define PCI_CONF1_DEV  0x0000f800
> > >   #define PCI_CONF1_FUNC 0x00000700
> > >   #define PCI_CONF1_REG  0x000000ff
> > > 
> > >   #define PCI_CONF1_ADDRESS(bus, dev, func, reg) \
> > >     (FIELD_PREP(PCI_CONF1_BUS, (bus)) | \
> > >      FIELD_PREP(PCI_CONF1_DEV, (dev)) | \
> > >      FIELD_PREP(PCI_CONF1_FUNC, (func)) | \
> > >      FIELD_PREP(PCI_CONF1_REG, (reg & ~0x3)))
> 
> This ended up not working, because FIELD_PREP() detects ext regs not 
> fitting into PCI_CONF1_REG:
> 	FIELD_PREP(PCI_CONF1_REG, (reg) & ~0x3)
> 
> There are two partially overlapping things here when it comes to reg 
> (addressing side and parameter input side):
> 
> #define PCI_CONF1_REG_ADDR	0x000000ff
> // for PCI_CONF1_EXT_ADDRESS:
> #define PCI_CONF1_EXT_REG_ADDR	0x0f000000
> 
> /* PCI Config register (parameter input side) */
> #define PCI_CONF1_REG		0x0fc
> #define PCI_CONF1_EXT_REG	0xf00
> 
> Would those 4 defines be acceptable? Or should I mark the input side with
> _IN or use different prefix for the defines?

No opinion here yet.  Maybe PCI_CONF1_EXT_ADDRESS() needs to
explicitly pull out the low 8 bits before giving them to
PCI_CONF1_ADDRESS()?

> > Yes, it makes sense to remove the extra layer.
> > 
> > One additional thing, I just noticed lots of arch/ code is duplicating 
> > this calculation so perhaps this should also be moved outside of 
> > drivers/pci/ into include/linux/pci.h ? (Not in the same patch.)
> 
> I also noticed you took PCI_CONF1_ENABLE away from PCI_CONF1_ADDRESS(),
> did you intend for it to be moved at the caller site?
> 
> Moving it outside of PCI_CONF1_ADDRESS() would certainly help reusing this 
> code as notall arch code wants PCI_CONF1_ENABLE I think.

Honestly, I didn't think about PCI_CONF1_ENABLE; I just wanted to show
the idea of using FIELD_PREP() directly in PCI_CONF1_ADDRESS().

I *did* later think that the "& ~0x3" part maybe doesn't belong in
PCI_CONF1_ADDRESS(), since that's really connected with the use of
readl()/writel() in the caller.  Hmmm, I guess only
faraday_raw_pci_read_config() and ixp4xx_config_addr() actually use
this.  Maybe those places should mask out the low bits themselves?

Maybe the same with PCI_CONF1_ENABLE, since ixp4xx_config_addr()
removes that bit anyway?  Not sure.

Bjorn
  

Patch

diff --git a/drivers/pci/pci.h b/drivers/pci/pci.h
index 39a8932dc340..31da9fde8aca 100644
--- a/drivers/pci/pci.h
+++ b/drivers/pci/pci.h
@@ -2,6 +2,8 @@ 
 #ifndef DRIVERS_PCI_H
 #define DRIVERS_PCI_H
 
+#include <linux/bitfield.h>
+#include <linux/bits.h>
 #include <linux/pci.h>
 
 /* Number of possible devfns: 0.0 to 1f.7 inclusive */
@@ -797,19 +799,15 @@  static inline pci_power_t mid_pci_get_power_state(struct pci_dev *pdev)
  * Section 3.2.2.3.2, Figure 3-2, p. 50.
  */
 
-#define PCI_CONF1_BUS_SHIFT	16 /* Bus number */
-#define PCI_CONF1_DEV_SHIFT	11 /* Device number */
-#define PCI_CONF1_FUNC_SHIFT	8  /* Function number */
-
-#define PCI_CONF1_BUS_MASK	0xff
-#define PCI_CONF1_DEV_MASK	0x1f
-#define PCI_CONF1_FUNC_MASK	0x7
+#define PCI_CONF1_BUS_MASK	GENMASK(23, 16)
+#define PCI_CONF1_DEV_MASK	GENMASK(15, 11)
+#define PCI_CONF1_FUNC_MASK	GENMASK(10, 8)
 #define PCI_CONF1_REG_MASK	0xfc /* Limit aligned offset to a maximum of 256B */
 
 #define PCI_CONF1_ENABLE	BIT(31)
-#define PCI_CONF1_BUS(x)	(((x) & PCI_CONF1_BUS_MASK) << PCI_CONF1_BUS_SHIFT)
-#define PCI_CONF1_DEV(x)	(((x) & PCI_CONF1_DEV_MASK) << PCI_CONF1_DEV_SHIFT)
-#define PCI_CONF1_FUNC(x)	(((x) & PCI_CONF1_FUNC_MASK) << PCI_CONF1_FUNC_SHIFT)
+#define PCI_CONF1_BUS(x)	FIELD_PREP(PCI_CONF1_BUS_MASK, (x))
+#define PCI_CONF1_DEV(x)	FIELD_PREP(PCI_CONF1_DEV_MASK, (x))
+#define PCI_CONF1_FUNC(x)	FIELD_PREP(PCI_CONF1_FUNC_MASK, (x))
 #define PCI_CONF1_REG(x)	((x) & PCI_CONF1_REG_MASK)
 
 #define PCI_CONF1_ADDRESS(bus, dev, func, reg) \
@@ -827,9 +825,8 @@  static inline pci_power_t mid_pci_get_power_state(struct pci_dev *pdev)
  * are used for specifying additional 4 high bits of PCI Express register.
  */
 
-#define PCI_CONF1_EXT_REG_SHIFT	16
-#define PCI_CONF1_EXT_REG_MASK	0xf00
-#define PCI_CONF1_EXT_REG(x)	(((x) & PCI_CONF1_EXT_REG_MASK) << PCI_CONF1_EXT_REG_SHIFT)
+#define PCI_CONF1_EXT_REG_MASK	GENMASK(27, 24)
+#define PCI_CONF1_EXT_REG(x)	FIELD_PREP(PCI_CONF1_EXT_REG_MASK, (x) >> 8)
 
 #define PCI_CONF1_EXT_ADDRESS(bus, dev, func, reg) \
 	(PCI_CONF1_ADDRESS(bus, dev, func, reg) | \