[v2,3/7] arm64: dts: mt8183: Add kukui katsu board

Message ID 20231024212618.1079676-4-hsinyi@chromium.org
State New
Headers
Series Add a few mt8183 follower boards. |

Commit Message

Hsin-Yi Wang Oct. 24, 2023, 9:22 p.m. UTC
  katsu is also known as ASUS Chromebook Detachable CZ1.

Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
---
v1->v2: non sku38 is sku32
---
 arch/arm64/boot/dts/mediatek/Makefile         |  2 +
 .../dts/mediatek/mt8183-kukui-katsu-sku32.dts | 40 +++++++++++++++++
 .../dts/mediatek/mt8183-kukui-katsu-sku38.dts | 44 +++++++++++++++++++
 3 files changed, 86 insertions(+)
 create mode 100644 arch/arm64/boot/dts/mediatek/mt8183-kukui-katsu-sku32.dts
 create mode 100644 arch/arm64/boot/dts/mediatek/mt8183-kukui-katsu-sku38.dts
  

Comments

AngeloGioacchino Del Regno Oct. 25, 2023, 8:25 a.m. UTC | #1
Il 24/10/23 23:22, Hsin-Yi Wang ha scritto:
> katsu is also known as ASUS Chromebook Detachable CZ1.
> 
> Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
> ---
> v1->v2: non sku38 is sku32
> ---
>   arch/arm64/boot/dts/mediatek/Makefile         |  2 +
>   .../dts/mediatek/mt8183-kukui-katsu-sku32.dts | 40 +++++++++++++++++
>   .../dts/mediatek/mt8183-kukui-katsu-sku38.dts | 44 +++++++++++++++++++
>   3 files changed, 86 insertions(+)
>   create mode 100644 arch/arm64/boot/dts/mediatek/mt8183-kukui-katsu-sku32.dts
>   create mode 100644 arch/arm64/boot/dts/mediatek/mt8183-kukui-katsu-sku38.dts
> 
> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> index e6e7592a3645..a13419e67e8e 100644
> --- a/arch/arm64/boot/dts/mediatek/Makefile
> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> @@ -36,6 +36,8 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-jacuzzi-willow-sku0.dtb
>   dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-jacuzzi-willow-sku1.dtb
>   dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-kakadu.dtb
>   dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-kakadu-sku22.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-katsu-sku32.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-katsu-sku38.dtb
>   dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-kodama-sku16.dtb
>   dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-kodama-sku272.dtb
>   dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-kodama-sku288.dtb
> diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-katsu-sku32.dts b/arch/arm64/boot/dts/mediatek/mt8183-kukui-katsu-sku32.dts
> new file mode 100644
> index 000000000000..9fa205c06c74
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-katsu-sku32.dts
> @@ -0,0 +1,40 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright 2023 Google LLC
> + */
> +
> +/dts-v1/;
> +#include "mt8183-kukui-kakadu.dtsi"
> +#include "mt8183-kukui-audio-da7219-rt1015p.dtsi"
> +
> +/ {
> +	model = "Google katsu board";
> +	chassis-type = "tablet";
> +	compatible = "google,katsu-sku32", "google,katsu", "mediatek,mt8183";
> +};
> +
> +&i2c0 {
> +	status = "okay";
> +

The i2c0 node already inherits status = "okay" from mt8183-kukui-kakadu.dtsi,
this is redundant.

> +	/delete-node/touchscreen@10;

You can definitely avoid those ugly /delete-node/ statements: if you check more
closely, mt8183-kukui-kakadu.dtsi is used by only two *.dts files.

I would propose to move the touchscreen@10 node from kakadu.dtsi to kakadu.dts
and kakadu-sku22.dts: in my opinion, that will make things more readable, as
every board defines its own touchscreen.

It would be a different story if we had to duplicate that @10 node for something
like five times or more, but that's not the case.

> +	touchscreen1: touchscreen@5d {
> +		compatible = "goodix,gt7375p";
> +		reg = <0x5d>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&open_touch>;
> +

This....

> +		interrupt-parent = <&pio>;
> +		interrupts = <155 IRQ_TYPE_LEVEL_LOW>;

...should be done in one line, like so:

		interrupts-extended = <&pio 155 IRQ_TYPE_LEVEL_LOW>;

> +
> +		reset-gpios = <&pio 156 GPIO_ACTIVE_LOW>;
> +		vdd-supply = <&lcd_pp3300>;
> +	};
> +};
> +
> +&panel {
> +	compatible = "starry,2081101qfh032011-53g";

Actually, same comment goes for the panel node: kakadu.dtsi defines a panel
compatible "boe,tv105wum-nw0" but then you're overriding it here with the
starry panel.

You could leave the status = "okay" in kakadu.dtsi and move the panel compatible
to each *.dts board file, therefore increasing readability.

> +};
> +
> +&qca_wifi {
> +	qcom,ath10k-calibration-variant = "GO_KATSU";
> +};

Same comment applies to sku38, of course.

Regards,
Angelo
  

Patch

diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index e6e7592a3645..a13419e67e8e 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -36,6 +36,8 @@  dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-jacuzzi-willow-sku0.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-jacuzzi-willow-sku1.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-kakadu.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-kakadu-sku22.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-katsu-sku32.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-katsu-sku38.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-kodama-sku16.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-kodama-sku272.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-kodama-sku288.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-katsu-sku32.dts b/arch/arm64/boot/dts/mediatek/mt8183-kukui-katsu-sku32.dts
new file mode 100644
index 000000000000..9fa205c06c74
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-katsu-sku32.dts
@@ -0,0 +1,40 @@ 
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright 2023 Google LLC
+ */
+
+/dts-v1/;
+#include "mt8183-kukui-kakadu.dtsi"
+#include "mt8183-kukui-audio-da7219-rt1015p.dtsi"
+
+/ {
+	model = "Google katsu board";
+	chassis-type = "tablet";
+	compatible = "google,katsu-sku32", "google,katsu", "mediatek,mt8183";
+};
+
+&i2c0 {
+	status = "okay";
+
+	/delete-node/touchscreen@10;
+	touchscreen1: touchscreen@5d {
+		compatible = "goodix,gt7375p";
+		reg = <0x5d>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&open_touch>;
+
+		interrupt-parent = <&pio>;
+		interrupts = <155 IRQ_TYPE_LEVEL_LOW>;
+
+		reset-gpios = <&pio 156 GPIO_ACTIVE_LOW>;
+		vdd-supply = <&lcd_pp3300>;
+	};
+};
+
+&panel {
+	compatible = "starry,2081101qfh032011-53g";
+};
+
+&qca_wifi {
+	qcom,ath10k-calibration-variant = "GO_KATSU";
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-katsu-sku38.dts b/arch/arm64/boot/dts/mediatek/mt8183-kukui-katsu-sku38.dts
new file mode 100644
index 000000000000..472a5a3ea25c
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-katsu-sku38.dts
@@ -0,0 +1,44 @@ 
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright 2023 Google LLC
+ */
+
+/dts-v1/;
+#include "mt8183-kukui-kakadu.dtsi"
+#include "mt8183-kukui-audio-rt1015p.dtsi"
+
+/ {
+	model = "Google katsu sku38 board";
+	chassis-type = "tablet";
+	compatible = "google,katsu-sku38", "google,katsu", "mediatek,mt8183";
+};
+
+&i2c0 {
+	status = "okay";
+
+	/delete-node/touchscreen@10;
+	touchscreen1: touchscreen@5d {
+		compatible = "goodix,gt7375p";
+		reg = <0x5d>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&open_touch>;
+
+		interrupt-parent = <&pio>;
+		interrupts = <155 IRQ_TYPE_LEVEL_LOW>;
+
+		reset-gpios = <&pio 156 GPIO_ACTIVE_LOW>;
+		vdd-supply = <&lcd_pp3300>;
+	};
+};
+
+&panel {
+	compatible = "starry,2081101qfh032011-53g";
+};
+
+&qca_wifi {
+	qcom,ath10k-calibration-variant = "GO_KATSU";
+};
+
+&sound {
+	compatible = "mediatek,mt8183_mt6358_ts3a227_rt1015p";
+};