[v2,2/7] drm/i915/dsi: Get rid of redundant 'else'
Commit Message
In the snippets like the following
if (...)
return / goto / break / continue ...;
else
...
the 'else' is redundant. Get rid of it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
---
drivers/gpu/drm/i915/display/intel_dsi_vbt.c | 58 ++++++++++----------
1 file changed, 28 insertions(+), 30 deletions(-)
Comments
Hi Andy,
On Tue, Oct 24, 2023 at 06:57:34PM +0300, Andy Shevchenko wrote:
> In the snippets like the following
>
> if (...)
> return / goto / break / continue ...;
> else
> ...
>
> the 'else' is redundant. Get rid of it.
>
> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Andi
@@ -142,7 +142,7 @@ static enum port intel_dsi_seq_port_to_port(struct intel_dsi *intel_dsi,
if (seq_port) {
if (intel_dsi->ports & BIT(PORT_B))
return PORT_B;
- else if (intel_dsi->ports & BIT(PORT_C))
+ if (intel_dsi->ports & BIT(PORT_C))
return PORT_C;
}
@@ -675,8 +675,8 @@ static const char *sequence_name(enum mipi_seq seq_id)
{
if (seq_id < ARRAY_SIZE(seq_name) && seq_name[seq_id])
return seq_name[seq_id];
- else
- return "(unknown)";
+
+ return "(unknown)";
}
static void intel_dsi_vbt_exec(struct intel_dsi *intel_dsi,
@@ -870,36 +870,34 @@ bool intel_dsi_vbt_init(struct intel_dsi *intel_dsi, u16 panel_id)
* multiply by 100 to preserve remainder
*/
if (intel_dsi->video_mode == BURST_MODE) {
- if (mipi_config->target_burst_mode_freq) {
- u32 bitrate = intel_dsi_bitrate(intel_dsi);
+ u32 bitrate;
- /*
- * Sometimes the VBT contains a slightly lower clock,
- * then the bitrate we have calculated, in this case
- * just replace it with the calculated bitrate.
- */
- if (mipi_config->target_burst_mode_freq < bitrate &&
- intel_fuzzy_clock_check(
- mipi_config->target_burst_mode_freq,
- bitrate))
- mipi_config->target_burst_mode_freq = bitrate;
-
- if (mipi_config->target_burst_mode_freq < bitrate) {
- drm_err(&dev_priv->drm,
- "Burst mode freq is less than computed\n");
- return false;
- }
-
- burst_mode_ratio = DIV_ROUND_UP(
- mipi_config->target_burst_mode_freq * 100,
- bitrate);
-
- intel_dsi->pclk = DIV_ROUND_UP(intel_dsi->pclk * burst_mode_ratio, 100);
- } else {
- drm_err(&dev_priv->drm,
- "Burst mode target is not set\n");
+ if (mipi_config->target_burst_mode_freq == 0) {
+ drm_err(&dev_priv->drm, "Burst mode target is not set\n");
return false;
}
+
+ bitrate = intel_dsi_bitrate(intel_dsi);
+
+ /*
+ * Sometimes the VBT contains a slightly lower clock, then
+ * the bitrate we have calculated, in this case just replace it
+ * with the calculated bitrate.
+ */
+ if (mipi_config->target_burst_mode_freq < bitrate &&
+ intel_fuzzy_clock_check(mipi_config->target_burst_mode_freq,
+ bitrate))
+ mipi_config->target_burst_mode_freq = bitrate;
+
+ if (mipi_config->target_burst_mode_freq < bitrate) {
+ drm_err(&dev_priv->drm, "Burst mode freq is less than computed\n");
+ return false;
+ }
+
+ burst_mode_ratio =
+ DIV_ROUND_UP(mipi_config->target_burst_mode_freq * 100, bitrate);
+
+ intel_dsi->pclk = DIV_ROUND_UP(intel_dsi->pclk * burst_mode_ratio, 100);
} else
burst_mode_ratio = 100;