[10/13] arm64: dts: qcom: msm8916-longcheer-l8910: Add sound and modem
Commit Message
From: Jonathan Albrieux <jonathan.albrieux@gmail.com>
Enable sound and modem for the Longcheer L8910 (BQ Aquaris X5).
The setup is similar to most MSM8916 devices, i.e.:
- QDSP6 audio
- Earpiece/headphones/microphones via digital/analog codec in
MSM8916/PM8916
- Audio jack detection via analog codec in PM8916
- WWAN Internet via BAM-DMUX
except:
- Awinic AW8738 connected to HPH_R (headphones) output of the analog
codec. Note that unlike for wingtech-wt88047 there is no analog
switch that would allow disabling output via the headphone jack
when the speaker is enabled.
Signed-off-by: Jonathan Albrieux <jonathan.albrieux@gmail.com>
Co-developed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
---
.../boot/dts/qcom/msm8916-longcheer-l8910.dts | 54 ++++++++++++++++++++++
1 file changed, 54 insertions(+)
Comments
On 26.09.2023 18:51, Stephan Gerhold wrote:
> From: Jonathan Albrieux <jonathan.albrieux@gmail.com>
>
> Enable sound and modem for the Longcheer L8910 (BQ Aquaris X5).
> The setup is similar to most MSM8916 devices, i.e.:
>
> - QDSP6 audio
> - Earpiece/headphones/microphones via digital/analog codec in
> MSM8916/PM8916
> - Audio jack detection via analog codec in PM8916
> - WWAN Internet via BAM-DMUX
>
> except:
>
> - Awinic AW8738 connected to HPH_R (headphones) output of the analog
> codec. Note that unlike for wingtech-wt88047 there is no analog
> switch that would allow disabling output via the headphone jack
> when the speaker is enabled.
>
> Signed-off-by: Jonathan Albrieux <jonathan.albrieux@gmail.com>
> Co-developed-by: Stephan Gerhold <stephan@gerhold.net>
> Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Konrad
@@ -3,6 +3,8 @@
/dts-v1/;
#include "msm8916-pm8916.dtsi"
+#include "msm8916-modem-qdsp6.dtsi"
+
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/leds/common.h>
@@ -22,6 +24,16 @@ chosen {
stdout-path = "serial0";
};
+ speaker_amp: audio-amplifier {
+ compatible = "awinic,aw8738";
+ mode-gpios = <&tlmm 114 GPIO_ACTIVE_HIGH>;
+ awinic,mode = <5>;
+ sound-name-prefix = "Speaker Amp";
+
+ pinctrl-0 = <&spk_ext_pa_default>;
+ pinctrl-names = "default";
+ };
+
flash-led-controller {
compatible = "ocs,ocp8110";
enable-gpios = <&tlmm 49 GPIO_ACTIVE_HIGH>;
@@ -107,6 +119,17 @@ &blsp_uart2 {
status = "okay";
};
+&mpss_mem {
+ reg = <0x0 0x86800000 0x0 0x5000000>;
+};
+
+&pm8916_codec {
+ qcom,micbias-lvl = <2800>;
+ qcom,mbhc-vthreshold-low = <75 100 120 180 500>;
+ qcom,mbhc-vthreshold-high = <75 100 120 180 500>;
+ qcom,hphl-jack-type-normally-open;
+};
+
&pm8916_resin {
status = "okay";
linux,code = <KEY_VOLUMEDOWN>;
@@ -137,6 +160,30 @@ &sdhc_2 {
cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
};
+&sound {
+ status = "okay";
+
+ /*
+ * Provide widgets/pin-switches to allow enabling speaker separately.
+ * The hardware does not provide a way to disable the output via the
+ * headphone jack when the speaker is enabled.
+ */
+ model = "bq-paella";
+ widgets =
+ "Speaker", "Speaker",
+ "Headphone", "Headphones";
+ pin-switches = "Speaker";
+ audio-routing =
+ "Speaker", "Speaker Amp OUT",
+ "Speaker Amp IN", "HPH_R",
+ "Headphones", "HPH_L",
+ "Headphones", "HPH_R",
+ "AMIC1", "MIC BIAS External1",
+ "AMIC2", "MIC BIAS Internal2",
+ "AMIC3", "MIC BIAS External1";
+ aux-devs = <&speaker_amp>;
+};
+
&usb {
status = "okay";
extcon = <&usb_id>, <&usb_id>;
@@ -205,6 +252,13 @@ sdc2_cd_default: sdc2-cd-default-state {
bias-disable;
};
+ spk_ext_pa_default: spk-ext-pa-default-state {
+ pins = "gpio114";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
usb_id_default: usb-id-default-state {
pins = "gpio110";
function = "gpio";