[3/3] arm64: dts: qcom: msm8916-*: Fix alphabetic node order
Commit Message
Fix a couple of instances of incorrectly sorted nodes in the MSM8916
boards. They should be ordered alphabetically for consistency.
No functional change.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
---
Changing the RGB LED node order to BGR is a bit funny but this is how
alphabetic ordering works. :-)
---
.../boot/dts/qcom/msm8916-alcatel-idol347.dts | 8 ++---
.../boot/dts/qcom/msm8916-samsung-a3u-eur.dts | 10 +++---
.../boot/dts/qcom/msm8916-samsung-gt5-common.dtsi | 38 +++++++++++-----------
arch/arm64/boot/dts/qcom/msm8916-thwc-uf896.dts | 8 ++---
arch/arm64/boot/dts/qcom/msm8916-thwc-ufi001c.dts | 8 ++---
.../arm64/boot/dts/qcom/msm8916-yiming-uz801v3.dts | 8 ++---
6 files changed, 40 insertions(+), 40 deletions(-)
@@ -58,10 +58,6 @@ usb_id: usb-id {
};
};
-&blsp_uart2 {
- status = "okay";
-};
-
&blsp_i2c4 {
status = "okay";
@@ -153,6 +149,10 @@ led@1 {
};
};
+&blsp_uart2 {
+ status = "okay";
+};
+
&pm8916_resin {
status = "okay";
linux,code = <KEY_VOLUMEDOWN>;
@@ -49,11 +49,6 @@ reg_key_led: regulator-key-led {
};
};
-&touchkey {
- vcc-supply = <®_touch_key>;
- vdd-supply = <®_key_led>;
-};
-
&accelerometer {
mount-matrix = "0", "1", "0",
"1", "0", "0",
@@ -108,6 +103,11 @@ &mdss_dsi0_out {
remote-endpoint = <&panel_in>;
};
+&touchkey {
+ vcc-supply = <®_touch_key>;
+ vdd-supply = <®_key_led>;
+};
+
&vibrator {
status = "okay";
};
@@ -65,25 +65,6 @@ hall-sensor-switch {
};
};
-&blsp_i2c4 {
- status = "okay";
-
- fuelgauge@36 {
- compatible = "maxim,max77849-battery";
- reg = <0x36>;
-
- maxim,rsns-microohm = <10000>;
- maxim,over-heat-temp = <600>;
- maxim,over-volt = <4400>;
-
- interrupt-parent = <&tlmm>;
- interrupts = <121 IRQ_TYPE_EDGE_FALLING>;
-
- pinctrl-0 = <&fuelgauge_int_default>;
- pinctrl-names = "default";
- };
-};
-
&blsp_i2c2 {
status = "okay";
@@ -112,6 +93,25 @@ accelerometer@1d {
};
};
+&blsp_i2c4 {
+ status = "okay";
+
+ fuelgauge@36 {
+ compatible = "maxim,max77849-battery";
+ reg = <0x36>;
+
+ maxim,rsns-microohm = <10000>;
+ maxim,over-heat-temp = <600>;
+ maxim,over-volt = <4400>;
+
+ interrupt-parent = <&tlmm>;
+ interrupts = <121 IRQ_TYPE_EDGE_FALLING>;
+
+ pinctrl-0 = <&fuelgauge_int_default>;
+ pinctrl-names = "default";
+ };
+};
+
&blsp_uart2 {
status = "okay";
};
@@ -13,16 +13,16 @@ &button_restart {
gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
};
-&led_r {
- gpios = <&tlmm 82 GPIO_ACTIVE_HIGH>;
+&led_b {
+ gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>;
};
&led_g {
gpios = <&tlmm 83 GPIO_ACTIVE_HIGH>;
};
-&led_b {
- gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>;
+&led_r {
+ gpios = <&tlmm 82 GPIO_ACTIVE_HIGH>;
};
&button_default {
@@ -13,16 +13,16 @@ &button_restart {
gpios = <&tlmm 37 GPIO_ACTIVE_HIGH>;
};
-&led_r {
- gpios = <&tlmm 22 GPIO_ACTIVE_HIGH>;
+&led_b {
+ gpios = <&tlmm 20 GPIO_ACTIVE_HIGH>;
};
&led_g {
gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
};
-&led_b {
- gpios = <&tlmm 20 GPIO_ACTIVE_HIGH>;
+&led_r {
+ gpios = <&tlmm 22 GPIO_ACTIVE_HIGH>;
};
&mpss {
@@ -13,16 +13,16 @@ &button_restart {
gpios = <&tlmm 23 GPIO_ACTIVE_LOW>;
};
-&led_r {
- gpios = <&tlmm 7 GPIO_ACTIVE_HIGH>;
+&led_b {
+ gpios = <&tlmm 6 GPIO_ACTIVE_HIGH>;
};
&led_g {
gpios = <&tlmm 8 GPIO_ACTIVE_HIGH>;
};
-&led_b {
- gpios = <&tlmm 6 GPIO_ACTIVE_HIGH>;
+&led_r {
+ gpios = <&tlmm 7 GPIO_ACTIVE_HIGH>;
};
&button_default {