[3/4] AMR: dts: st: ste: switch to enable-gpios
Commit Message
The recommended name for enable GPIOs property in regulator-gpio is
"enable-gpios". This is also required by bindings:
ste-hrefv60plus-stuib.dtb: regulator-gpio: Unevaluated properties are not allowed ('enable-gpio' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
arch/arm/boot/dts/st/ste-href520-tvk.dts | 2 +-
arch/arm/boot/dts/st/ste-hrefprev60-stuib.dts | 2 +-
arch/arm/boot/dts/st/ste-hrefprev60-tvk.dts | 2 +-
arch/arm/boot/dts/st/ste-hrefv60plus-stuib.dts | 2 +-
arch/arm/boot/dts/st/ste-hrefv60plus-tvk.dts | 2 +-
arch/arm/boot/dts/st/ste-snowball.dts | 2 +-
6 files changed, 6 insertions(+), 6 deletions(-)
Comments
On 26/07/2023 09:03, Krzysztof Kozlowski wrote:
> The recommended name for enable GPIOs property in regulator-gpio is
> "enable-gpios". This is also required by bindings:
>
> ste-hrefv60plus-stuib.dtb: regulator-gpio: Unevaluated properties are not allowed ('enable-gpio' was unexpected)
>
Subject prefix needs fixes (AMR->ARM)
Best regards,
Krzysztof
On Wed, Jul 26, 2023 at 9:03 AM Krzysztof Kozlowski
<krzysztof.kozlowski@linaro.org> wrote:
> The recommended name for enable GPIOs property in regulator-gpio is
> "enable-gpios". This is also required by bindings:
>
> ste-hrefv60plus-stuib.dtb: regulator-gpio: Unevaluated properties are not allowed ('enable-gpio' was unexpected)
>
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Hm if the subject start turning ARM: dts: st: ste: on these I might
need to consider
to move the ste(ricsson) stuff out of dts/st, this series mixes up the Ux500 and
st maintainers. I can deal with this one but if it confuses the scripts that's
not good.
Anyways, patch applied! (With subject fixed.)
Yours,
Linus Walleij
@@ -28,7 +28,7 @@ vmmci: regulator-gpio {
2900000 0x0>;
gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
- enable-gpio = <&gpio2 14 GPIO_ACTIVE_HIGH>;
+ enable-gpios = <&gpio2 14 GPIO_ACTIVE_HIGH>;
enable-active-high;
pinctrl-names = "default";
@@ -27,7 +27,7 @@ vmmci: regulator-gpio {
2900000 0x0>;
gpios = <&tc3589x_gpio 18 GPIO_ACTIVE_HIGH>;
- enable-gpio = <&tc3589x_gpio 17 GPIO_ACTIVE_HIGH>;
+ enable-gpios = <&tc3589x_gpio 17 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
@@ -27,7 +27,7 @@ vmmci: regulator-gpio {
2900000 0x0>;
gpios = <&tc3589x_gpio 18 GPIO_ACTIVE_HIGH>;
- enable-gpio = <&tc3589x_gpio 17 GPIO_ACTIVE_HIGH>;
+ enable-gpios = <&tc3589x_gpio 17 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
};
@@ -29,7 +29,7 @@ vmmci: regulator-gpio {
2900000 0x0>;
gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
- enable-gpio = <&gpio5 9 GPIO_ACTIVE_HIGH>;
+ enable-gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>;
enable-active-high;
pinctrl-names = "default";
@@ -29,7 +29,7 @@ vmmci: regulator-gpio {
2900000 0x0>;
gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
- enable-gpio = <&gpio5 9 GPIO_ACTIVE_HIGH>;
+ enable-gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>;
enable-active-high;
pinctrl-names = "default";
@@ -229,7 +229,7 @@ vmmci: regulator-gpio {
/* GPIO228 SD_SEL */
gpios = <&gpio7 4 GPIO_ACTIVE_HIGH>;
/* GPIO217 MMC_EN */
- enable-gpio = <&gpio6 25 GPIO_ACTIVE_HIGH>;
+ enable-gpios = <&gpio6 25 GPIO_ACTIVE_HIGH>;
enable-active-high;
regulator-min-microvolt = <1800000>;