diff mbox series

[v3] arm64: dts: ti: k3-j721e: Add overlay to enable CPSW9G ports with GESI

Message ID 20230725073057.96705-1-s-vadapalli@ti.com
State New
Headers
Series [v3] arm64: dts: ti: k3-j721e: Add overlay to enable CPSW9G ports with GESI |

Commit Message

Siddharth Vadapalli July 25, 2023, 7:30 a.m. UTC 
  The J7 GESI EXP board for J721E Common-Proc-Board supports RGMII mode.
Use the overlay to configure CPSW9G ports in RGMII-RXID mode.

Add aliases for CPSW9G ports to enable kernel to fetch MAC addresses
directly from U-Boot.

Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
---

NOTE: This patch is based on linux-next tagged next-20230725.

v2:
https://lore.kernel.org/r/20230710075551.1109024-1-s-vadapalli@ti.com/
Changes since v2:
- Collect Reviewed-by tag from Ravi Gunasekaran <r-gunasekaran@ti.com>
- Rename rgmii1_pins_default, rgmii2_pins_default, rgmii3_pins_default,
  rgmii4_pins_default and mdio0_pins_default to:
  rgmii1_default_pins, rgmii2_default_pins, rgmii3_default_pins,
  rgmii4_default_pins and mdio0_default_pins respectively.
- Rename rgmii1-pins-default, rgmii2-pins-default, rgmii3-pins-default,
  rgmii4-pins-default and mdio0-pins-default to:
  rgmii1-default-pins, rgmii2-default-pins, rgmii3-default-pins,
  rgmii4-default-pins and mdio0-default-pins respectively.
- The above changes are performed to follow the updated json-schema
  patch at:
  https://lore.kernel.org/all/169021456020.3622493.10284534202541859578.robh@kernel.org/ 

v1:
https://lore.kernel.org/r/20230529094222.512675-1-s-vadapalli@ti.com/
Changes since v1:
- Rebase on linux-next tagged next-20230710.

 arch/arm64/boot/dts/ti/Makefile               |   2 +
 .../dts/ti/k3-j721e-evm-gesi-exp-board.dtso   | 196 ++++++++++++++++++
 2 files changed, 198 insertions(+)
 create mode 100644 arch/arm64/boot/dts/ti/k3-j721e-evm-gesi-exp-board.dtso

Comments

Nishanth Menon Aug. 2, 2023, 5:04 a.m. UTC | #1 
Hi Siddharth Vadapalli,

On Tue, 25 Jul 2023 13:00:57 +0530, Siddharth Vadapalli wrote:
> The J7 GESI EXP board for J721E Common-Proc-Board supports RGMII mode.
> Use the overlay to configure CPSW9G ports in RGMII-RXID mode.
> 
> Add aliases for CPSW9G ports to enable kernel to fetch MAC addresses
> directly from U-Boot.
> 
> 
> [...]

I have applied the following to branch ti-k3-dts-next on [1].
Thank you!

[1/1] arm64: dts: ti: k3-j721e: Add overlay to enable CPSW9G ports with GESI
      commit: 7815b2816d146f302f3884ee8e87c7b39fea1ecc

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent up the chain during
the next merge window (or sooner if it is a relevant bug fix), however if
problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux.git
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index 6dd7b6f1d6ab..01d58aa8b06e 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -46,6 +46,7 @@  dtb-$(CONFIG_ARCH_K3) += k3-j7200-evm.dtb
 k3-j721e-evm-dtbs := k3-j721e-common-proc-board.dtb k3-j721e-evm-quad-port-eth-exp.dtbo
 dtb-$(CONFIG_ARCH_K3) += k3-j721e-beagleboneai64.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-j721e-evm.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-j721e-evm-gesi-exp-board.dtbo
 dtb-$(CONFIG_ARCH_K3) += k3-j721e-sk.dtb
 
 # Boards with J721s2 SoC
@@ -58,3 +59,4 @@  dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm.dtb
 
 # Enable support for device-tree overlays
 DTC_FLAGS_k3-am6548-iot2050-advanced-m2 += -@
+DTC_FLAGS_k3-j721e-common-proc-board += -@
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-evm-gesi-exp-board.dtso b/arch/arm64/boot/dts/ti/k3-j721e-evm-gesi-exp-board.dtso
new file mode 100644
index 000000000000..6a7d37575da1
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-j721e-evm-gesi-exp-board.dtso
@@ -0,0 +1,196 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/**
+ * DT Overlay for CPSW9G in RGMII mode using J7 GESI EXP BRD board with
+ * J721E board.
+ *
+ * GESI Board Product Link: https://www.ti.com/tool/J7EXPCXEVM
+ *
+ * Copyright (C) 2023 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/net/ti-dp83867.h>
+
+#include "k3-pinctrl.h"
+
+&{/} {
+	aliases {
+		ethernet1 = "/bus@100000/ethernet@c000000/ethernet-ports/port@1";
+		ethernet2 = "/bus@100000/ethernet@c000000/ethernet-ports/port@2";
+		ethernet3 = "/bus@100000/ethernet@c000000/ethernet-ports/port@3";
+		ethernet4 = "/bus@100000/ethernet@c000000/ethernet-ports/port@4";
+	};
+};
+
+&cpsw0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii1_default_pins
+		     &rgmii2_default_pins
+		     &rgmii3_default_pins
+		     &rgmii4_default_pins>;
+};
+
+&cpsw0_port1 {
+	status = "okay";
+	phy-handle = <&cpsw9g_phy12>;
+	phy-mode = "rgmii-rxid";
+	mac-address = [00 00 00 00 00 00];
+	phys = <&cpsw0_phy_gmii_sel 1>;
+};
+
+&cpsw0_port2 {
+	status = "okay";
+	phy-handle = <&cpsw9g_phy15>;
+	phy-mode = "rgmii-rxid";
+	mac-address = [00 00 00 00 00 00];
+	phys = <&cpsw0_phy_gmii_sel 2>;
+};
+
+&cpsw0_port3 {
+	status = "okay";
+	phy-handle = <&cpsw9g_phy0>;
+	phy-mode = "rgmii-rxid";
+	mac-address = [00 00 00 00 00 00];
+	phys = <&cpsw0_phy_gmii_sel 3>;
+};
+
+&cpsw0_port4 {
+	status = "okay";
+	phy-handle = <&cpsw9g_phy3>;
+	phy-mode = "rgmii-rxid";
+	mac-address = [00 00 00 00 00 00];
+	phys = <&cpsw0_phy_gmii_sel 4>;
+};
+
+&cpsw9g_mdio {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mdio0_default_pins>;
+	bus_freq = <1000000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	cpsw9g_phy0: ethernet-phy@0 {
+		reg = <0>;
+		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+		ti,min-output-impedance;
+	};
+	cpsw9g_phy3: ethernet-phy@3 {
+		reg = <3>;
+		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+		ti,min-output-impedance;
+	};
+	cpsw9g_phy12: ethernet-phy@12 {
+		reg = <12>;
+		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+		ti,min-output-impedance;
+	};
+	cpsw9g_phy15: ethernet-phy@15 {
+		reg = <15>;
+		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+		ti,min-output-impedance;
+	};
+};
+
+&exp1 {
+	p15-hog {
+		/* P15 - EXP_MUX2 */
+		gpio-hog;
+		gpios = <13 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "EXP_MUX2";
+	};
+
+	p16-hog {
+		/* P16 - EXP_MUX3 */
+		gpio-hog;
+		gpios = <14 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "EXP_MUX3";
+	};
+};
+
+&main_pmx0 {
+	mdio0_default_pins: mdio0-default-pins {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x1bc, PIN_OUTPUT, 0) /* (V24) MDIO0_MDC */
+			J721E_IOPAD(0x1b8, PIN_INPUT, 0) /* (V26) MDIO0_MDIO */
+		>;
+	};
+
+	rgmii1_default_pins: rgmii1-default-pins {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x4, PIN_INPUT, 4) /* (AC23) PRG1_PRU0_GPO0.RGMII1_RD0 */
+			J721E_IOPAD(0x8, PIN_INPUT, 4) /* (AG22) PRG1_PRU0_GPO1.RGMII1_RD1 */
+			J721E_IOPAD(0xc, PIN_INPUT, 4) /* (AF22) PRG1_PRU0_GPO2.RGMII1_RD2 */
+			J721E_IOPAD(0x10, PIN_INPUT, 4) /* (AJ23) PRG1_PRU0_GPO3.RGMII1_RD3 */
+			J721E_IOPAD(0x1c, PIN_INPUT, 4) /* (AD22) PRG1_PRU0_GPO6.RGMII1_RXC */
+			J721E_IOPAD(0x14, PIN_INPUT, 4) /* (AH23) PRG1_PRU0_GPO4.RGMII1_RX_CTL */
+			J721E_IOPAD(0x30, PIN_OUTPUT, 4) /* (AF24) PRG1_PRU0_GPO11.RGMII1_TD0 */
+			J721E_IOPAD(0x34, PIN_OUTPUT, 4) /* (AJ24) PRG1_PRU0_GPO12.RGMII1_TD1 */
+			J721E_IOPAD(0x38, PIN_OUTPUT, 4) /* (AG24) PRG1_PRU0_GPO13.RGMII1_TD2 */
+			J721E_IOPAD(0x3c, PIN_OUTPUT, 4) /* (AD24) PRG1_PRU0_GPO14.RGMII1_TD3 */
+			J721E_IOPAD(0x44, PIN_OUTPUT, 4) /* (AE24) PRG1_PRU0_GPO16.RGMII1_TXC */
+			J721E_IOPAD(0x40, PIN_OUTPUT, 4) /* (AC24) PRG1_PRU0_GPO15.RGMII1_TX_CTL */
+		>;
+	};
+
+	rgmii2_default_pins: rgmii2-default-pins {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x58, PIN_INPUT, 4) /* (AE22) PRG1_PRU1_GPO0.RGMII2_RD0 */
+			J721E_IOPAD(0x5c, PIN_INPUT, 4) /* (AG23) PRG1_PRU1_GPO1.RGMII2_RD1 */
+			J721E_IOPAD(0x60, PIN_INPUT, 4) /* (AF23) PRG1_PRU1_GPO2.RGMII2_RD2 */
+			J721E_IOPAD(0x64, PIN_INPUT, 4) /* (AD23) PRG1_PRU1_GPO3.RGMII2_RD3 */
+			J721E_IOPAD(0x70, PIN_INPUT, 4) /* (AE23) PRG1_PRU1_GPO6.RGMII2_RXC */
+			J721E_IOPAD(0x68, PIN_INPUT, 4) /* (AH24) PRG1_PRU1_GPO4.RGMII2_RX_CTL */
+			J721E_IOPAD(0x84, PIN_OUTPUT, 4) /* (AJ25) PRG1_PRU1_GPO11.RGMII2_TD0 */
+			J721E_IOPAD(0x88, PIN_OUTPUT, 4) /* (AH25) PRG1_PRU1_GPO12.RGMII2_TD1 */
+			J721E_IOPAD(0x8c, PIN_OUTPUT, 4) /* (AG25) PRG1_PRU1_GPO13.RGMII2_TD2 */
+			J721E_IOPAD(0x90, PIN_OUTPUT, 4) /* (AH26) PRG1_PRU1_GPO14.RGMII2_TD3 */
+			J721E_IOPAD(0x98, PIN_OUTPUT, 4) /* (AJ26) PRG1_PRU1_GPO16.RGMII2_TXC */
+			J721E_IOPAD(0x94, PIN_OUTPUT, 4) /* (AJ27) PRG1_PRU1_GPO15.RGMII2_TX_CTL */
+		>;
+	};
+
+	rgmii3_default_pins: rgmii3-default-pins {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0xb0, PIN_INPUT, 4) /* (AF28) PRG0_PRU0_GPO0.RGMII3_RD0 */
+			J721E_IOPAD(0xb4, PIN_INPUT, 4) /* (AE28) PRG0_PRU0_GPO1.RGMII3_RD1 */
+			J721E_IOPAD(0xb8, PIN_INPUT, 4) /* (AE27) PRG0_PRU0_GPO2.RGMII3_RD2 */
+			J721E_IOPAD(0xbc, PIN_INPUT, 4) /* (AD26) PRG0_PRU0_GPO3.RGMII3_RD3 */
+			J721E_IOPAD(0xc8, PIN_INPUT, 4) /* (AE26) PRG0_PRU0_GPO6.RGMII3_RXC */
+			J721E_IOPAD(0xc0, PIN_INPUT, 4) /* (AD25) PRG0_PRU0_GPO4.RGMII3_RX_CTL */
+			J721E_IOPAD(0xdc, PIN_OUTPUT, 4) /* (AJ28) PRG0_PRU0_GPO11.RGMII3_TD0 */
+			J721E_IOPAD(0xe0, PIN_OUTPUT, 4) /* (AH27) PRG0_PRU0_GPO12.RGMII3_TD1 */
+			J721E_IOPAD(0xe4, PIN_OUTPUT, 4) /* (AH29) PRG0_PRU0_GPO13.RGMII3_TD2 */
+			J721E_IOPAD(0xe8, PIN_OUTPUT, 4) /* (AG28) PRG0_PRU0_GPO14.RGMII3_TD3 */
+			J721E_IOPAD(0xf0, PIN_OUTPUT, 4) /* (AH28) PRG0_PRU0_GPO16.RGMII3_TXC */
+			J721E_IOPAD(0xec, PIN_OUTPUT, 4) /* (AG27) PRG0_PRU0_GPO15.RGMII3_TX_CTL */
+		>;
+	};
+
+	rgmii4_default_pins: rgmii4-default-pins {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x100, PIN_INPUT, 4) /* (AE29) PRG0_PRU1_GPO0.RGMII4_RD0 */
+			J721E_IOPAD(0x104, PIN_INPUT, 4) /* (AD28) PRG0_PRU1_GPO1.RGMII4_RD1 */
+			J721E_IOPAD(0x108, PIN_INPUT, 4) /* (AD27) PRG0_PRU1_GPO2.RGMII4_RD2 */
+			J721E_IOPAD(0x10c, PIN_INPUT, 4) /* (AC25) PRG0_PRU1_GPO3.RGMII4_RD3 */
+			J721E_IOPAD(0x118, PIN_INPUT, 4) /* (AC26) PRG0_PRU1_GPO6.RGMII4_RXC */
+			J721E_IOPAD(0x110, PIN_INPUT, 4) /* (AD29) PRG0_PRU1_GPO4.RGMII4_RX_CTL */
+			J721E_IOPAD(0x12c, PIN_OUTPUT, 4) /* (AG26) PRG0_PRU1_GPO11.RGMII4_TD0 */
+			J721E_IOPAD(0x130, PIN_OUTPUT, 4) /* (AF27) PRG0_PRU1_GPO12.RGMII4_TD1 */
+			J721E_IOPAD(0x134, PIN_OUTPUT, 4) /* (AF26) PRG0_PRU1_GPO13.RGMII4_TD2 */
+			J721E_IOPAD(0x138, PIN_OUTPUT, 4) /* (AE25) PRG0_PRU1_GPO14.RGMII4_TD3 */
+			J721E_IOPAD(0x140, PIN_OUTPUT, 4) /* (AG29) PRG0_PRU1_GPO16.RGMII4_TXC */
+			J721E_IOPAD(0x13c, PIN_OUTPUT, 4) /* (AF29) PRG0_PRU1_GPO15.RGMII4_TX_CTL */
+		>;
+	};
+};