[1/2] ARM: dts: imx6qdl: Add Variscite VAR-SOM-MX6 SoM support
Commit Message
This patch adds support for the Variscite VAR_SOM-MX6 SoM with :
- i.MX6 Quad or Dual Lite SoC
- 256 – 4096 MB DDR3
- 4-64 GB eMMC
- 128 – 1024 MB SLC NAND
- Camera Interface
- HDMI+CEC interface
- LVDS / DSI / Parallel RGB interfaces
- Ethernet RGMII interface
- On-SoM Wi-Fi/Bluetooth with WiLink wl183x SDIO Module
- SD/MMC/SDIO interface
- USB Host + USB OTG interface
- I2C interfaces
- SPI interfaces
- PCI-Express 2.0 interface
- on-SoM Audio Codec with HP/Line-In interfaces + DMIC interface
- Digital Audio interface
- S/PDIF interface
Product website : https://www.variscite.com/product/system-on-module-som/cortex-a9/var-som-mx6-cpu-freescale-imx6/
Support is handled with a SoM-centric dtsi exporting the default interfaces
along the default pinmuxing to be enabled by the board dts file.
This file is based on the one provided by Variscite on their own
kernel, but adapted for mainline.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: James Hilliard <james.hilliard1@gmail.com>
---
arch/arm/boot/dts/imx6qdl-var-som.dtsi | 547 +++++++++++++++++++++++++
1 file changed, 547 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6qdl-var-som.dtsi
Comments
On 19/07/2023 18:00, James Hilliard wrote:
> This patch adds support for the Variscite VAR_SOM-MX6 SoM with :
> - i.MX6 Quad or Dual Lite SoC
> - 256 – 4096 MB DDR3
> - 4-64 GB eMMC
> - 128 – 1024 MB SLC NAND
> - Camera Interface
> - HDMI+CEC interface
> - LVDS / DSI / Parallel RGB interfaces
> - Ethernet RGMII interface
> - On-SoM Wi-Fi/Bluetooth with WiLink wl183x SDIO Module
> - SD/MMC/SDIO interface
> - USB Host + USB OTG interface
> - I2C interfaces
> - SPI interfaces
> - PCI-Express 2.0 interface
> - on-SoM Audio Codec with HP/Line-In interfaces + DMIC interface
> - Digital Audio interface
> - S/PDIF interface
>
> Product website : https://www.variscite.com/product/system-on-module-som/cortex-a9/var-som-mx6-cpu-freescale-imx6/
>
> Support is handled with a SoM-centric dtsi exporting the default interfaces
> along the default pinmuxing to be enabled by the board dts file.
>
> This file is based on the one provided by Variscite on their own
> kernel, but adapted for mainline.
>
> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
> Signed-off-by: James Hilliard <james.hilliard1@gmail.com>
> ---
> arch/arm/boot/dts/imx6qdl-var-som.dtsi | 547 +++++++++++++++++++++++++
> 1 file changed, 547 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6qdl-var-som.dtsi
>
> diff --git a/arch/arm/boot/dts/imx6qdl-var-som.dtsi b/arch/arm/boot/dts/imx6qdl-var-som.dtsi
> new file mode 100644
> index 000000000000..e93dae59624e
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6qdl-var-som.dtsi
> @@ -0,0 +1,547 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Support for Variscite VAR-SOM-MX6 Module
> + *
> + * Copyright 2011 Linaro Ltd.
> + * Copyright 2012 Freescale Semiconductor, Inc.
> + * Copyright (C) 2014-2016 Variscite, Ltd.
> + * Author: Donio Ron <ron.d@variscite.com>
> + * Copyright 2022 Bootlin
> + */
> +
> +/dts-v1/;
> +
> +#include "imx6q.dtsi"
> +#include <dt-bindings/clock/imx6qdl-clock.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/sound/fsl-imx-audmux.h>
> +
> +/ {
> + model = "Variscite i.MX6 QUAD/DUAL VAR-SOM-MX6";
> + compatible = "fsl,imx6q";
That's not correct compatible. It's not Imx6 soc. It's a som.
> +...
> +
> + sound: sound {
> + compatible = "simple-audio-card";
> + simple-audio-card,name = "var-som-audio";
> + simple-audio-card,format = "i2s";
> + simple-audio-card,bitclock-master = <&sound_codec>;
> + simple-audio-card,frame-master = <&sound_codec>;
> + simple-audio-card,widgets = "Headphone", "Headphone Jack",
> + "Line", "Line In", "Microphone", "Mic Jack";
> + simple-audio-card,routing = "Headphone Jack", "HPLOUT",
> + "Headphone Jack", "HPROUT",
> + "LINE1L", "Line In",
> + "LINE1R", "Line In";
> +
> + sound_cpu: simple-audio-card,cpu {
> + sound-dai = <&ssi2>;
> + };
> +
> + sound_codec: simple-audio-card,codec {
> + sound-dai = <&tlv320aic3106>;
> + clocks = <&clks IMX6QDL_CLK_CKO>;
> + };
> + };
> +
> + wlan_bt_rfkill {
No underscores in node names.
Just "rfkill"
> + compatible = "rfkill-gpio";
> + name = "wlan_bt_rfkill";
> + type = <2>; /* bluetooth */
> + gpios = <&gpio6 18 GPIO_ACTIVE_HIGH>;
> + };
> +};
> +
...
> + tlv320aic3106: codec@1b {
> + compatible = "ti,tlv320aic3106";
> + reg = <0x1b>;
> + #sound-dai-cells = <0>;
> + DRVDD-supply = <®_3p3v>;
> + AVDD-supply = <®_3p3v>;
> + IOVDD-supply = <®_3p3v>;
> + DVDD-supply = <®_3p3v>;
> + ai3x-ocmv = <0>;
> + reset-gpios = <&gpio4 5 GPIO_ACTIVE_LOW>;
> + ai3x-gpio-func = <
> + 0 /* AIC3X_GPIO1_FUNC_DISABLED */
> + 5 /* AIC3X_GPIO2_FUNC_DIGITAL_MIC_INPUT */
> + >;
> + };
> +};
> +
> +&iomuxc {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hog>;
> +
> + imx6qdl-var-som-mx6 {
> + pinctrl_hog: hoggrp {
> + fsl,pins = <
> + /* CTW6120 IRQ */
> + MX6QDL_PAD_EIM_DA7__GPIO3_IO07 0x80000000
> + /* SDMMC2 CD/WP */
> + MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x80000000
> + MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x80000000
> + >;
> + };
> +
> + pinctrl_audmux: audmux {
It does not look like you tested the DTS against bindings. Please run
`make dtbs_check` (see
Documentation/devicetree/bindings/writing-schema.rst or
https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/
for instructions).
AFAIR, all of them end with grp
...
> +
> +&usdhc3 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc3>;
> + pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
> + bus-width = <4>;
> + vmmc-supply = <®_wl18xx_vmmc>;
> + non-removable;
> + wakeup-source;
> + keep-power-in-suspend;
> + cap-power-off-card;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "okay";
> +
> + wlcore: wlcore@0 {
Generic node names. Is this wifi?
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
> + compatible = "ti,wl1835";
> + reg = <2>;
Best regards,
Krzysztof
On Wed, Jul 19, 2023 at 11:16 AM Krzysztof Kozlowski
<krzysztof.kozlowski@linaro.org> wrote:
>
> On 19/07/2023 18:00, James Hilliard wrote:
> > This patch adds support for the Variscite VAR_SOM-MX6 SoM with :
> > - i.MX6 Quad or Dual Lite SoC
> > - 256 – 4096 MB DDR3
> > - 4-64 GB eMMC
> > - 128 – 1024 MB SLC NAND
> > - Camera Interface
> > - HDMI+CEC interface
> > - LVDS / DSI / Parallel RGB interfaces
> > - Ethernet RGMII interface
> > - On-SoM Wi-Fi/Bluetooth with WiLink wl183x SDIO Module
> > - SD/MMC/SDIO interface
> > - USB Host + USB OTG interface
> > - I2C interfaces
> > - SPI interfaces
> > - PCI-Express 2.0 interface
> > - on-SoM Audio Codec with HP/Line-In interfaces + DMIC interface
> > - Digital Audio interface
> > - S/PDIF interface
> >
> > Product website : https://www.variscite.com/product/system-on-module-som/cortex-a9/var-som-mx6-cpu-freescale-imx6/
> >
> > Support is handled with a SoM-centric dtsi exporting the default interfaces
> > along the default pinmuxing to be enabled by the board dts file.
> >
> > This file is based on the one provided by Variscite on their own
> > kernel, but adapted for mainline.
> >
> > Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
> > Signed-off-by: James Hilliard <james.hilliard1@gmail.com>
> > ---
> > arch/arm/boot/dts/imx6qdl-var-som.dtsi | 547 +++++++++++++++++++++++++
> > 1 file changed, 547 insertions(+)
> > create mode 100644 arch/arm/boot/dts/imx6qdl-var-som.dtsi
> >
> > diff --git a/arch/arm/boot/dts/imx6qdl-var-som.dtsi b/arch/arm/boot/dts/imx6qdl-var-som.dtsi
> > new file mode 100644
> > index 000000000000..e93dae59624e
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/imx6qdl-var-som.dtsi
> > @@ -0,0 +1,547 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/*
> > + * Support for Variscite VAR-SOM-MX6 Module
> > + *
> > + * Copyright 2011 Linaro Ltd.
> > + * Copyright 2012 Freescale Semiconductor, Inc.
> > + * Copyright (C) 2014-2016 Variscite, Ltd.
> > + * Author: Donio Ron <ron.d@variscite.com>
> > + * Copyright 2022 Bootlin
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "imx6q.dtsi"
> > +#include <dt-bindings/clock/imx6qdl-clock.h>
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/sound/fsl-imx-audmux.h>
> > +
> > +/ {
> > + model = "Variscite i.MX6 QUAD/DUAL VAR-SOM-MX6";
> > + compatible = "fsl,imx6q";
>
> That's not correct compatible. It's not Imx6 soc. It's a som.
I'm confused, AFAIU the VAR-SOM-MX6 uses an imx6q SoC.
>
> > +...
> > +
> > + sound: sound {
> > + compatible = "simple-audio-card";
> > + simple-audio-card,name = "var-som-audio";
> > + simple-audio-card,format = "i2s";
> > + simple-audio-card,bitclock-master = <&sound_codec>;
> > + simple-audio-card,frame-master = <&sound_codec>;
> > + simple-audio-card,widgets = "Headphone", "Headphone Jack",
> > + "Line", "Line In", "Microphone", "Mic Jack";
> > + simple-audio-card,routing = "Headphone Jack", "HPLOUT",
> > + "Headphone Jack", "HPROUT",
> > + "LINE1L", "Line In",
> > + "LINE1R", "Line In";
> > +
> > + sound_cpu: simple-audio-card,cpu {
> > + sound-dai = <&ssi2>;
> > + };
> > +
> > + sound_codec: simple-audio-card,codec {
> > + sound-dai = <&tlv320aic3106>;
> > + clocks = <&clks IMX6QDL_CLK_CKO>;
> > + };
> > + };
> > +
> > + wlan_bt_rfkill {
>
> No underscores in node names.
>
> Just "rfkill"
>
>
> > + compatible = "rfkill-gpio";
> > + name = "wlan_bt_rfkill";
> > + type = <2>; /* bluetooth */
> > + gpios = <&gpio6 18 GPIO_ACTIVE_HIGH>;
> > + };
> > +};
> > +
>
> ...
>
> > + tlv320aic3106: codec@1b {
> > + compatible = "ti,tlv320aic3106";
> > + reg = <0x1b>;
> > + #sound-dai-cells = <0>;
> > + DRVDD-supply = <®_3p3v>;
> > + AVDD-supply = <®_3p3v>;
> > + IOVDD-supply = <®_3p3v>;
> > + DVDD-supply = <®_3p3v>;
> > + ai3x-ocmv = <0>;
> > + reset-gpios = <&gpio4 5 GPIO_ACTIVE_LOW>;
> > + ai3x-gpio-func = <
> > + 0 /* AIC3X_GPIO1_FUNC_DISABLED */
> > + 5 /* AIC3X_GPIO2_FUNC_DIGITAL_MIC_INPUT */
> > + >;
> > + };
> > +};
> > +
> > +&iomuxc {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_hog>;
> > +
> > + imx6qdl-var-som-mx6 {
> > + pinctrl_hog: hoggrp {
> > + fsl,pins = <
> > + /* CTW6120 IRQ */
> > + MX6QDL_PAD_EIM_DA7__GPIO3_IO07 0x80000000
> > + /* SDMMC2 CD/WP */
> > + MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x80000000
> > + MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x80000000
> > + >;
> > + };
> > +
> > + pinctrl_audmux: audmux {
>
> It does not look like you tested the DTS against bindings. Please run
> `make dtbs_check` (see
> Documentation/devicetree/bindings/writing-schema.rst or
> https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/
> for instructions).
>
> AFAIR, all of them end with grp
Ah, that's def throwing a bunch of warnings, although quite a few look
to be existing
issues in dependent dtsi files. I'll clean up what I can there.
>
>
> ...
>
> > +
> > +&usdhc3 {
> > + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> > + pinctrl-0 = <&pinctrl_usdhc3>;
> > + pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
> > + pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
> > + bus-width = <4>;
> > + vmmc-supply = <®_wl18xx_vmmc>;
> > + non-removable;
> > + wakeup-source;
> > + keep-power-in-suspend;
> > + cap-power-off-card;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + status = "okay";
> > +
> > + wlcore: wlcore@0 {
>
> Generic node names. Is this wifi?
I think it also supports bluetooth technically, although that might be
under a different node.
>
> https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
>
> > + compatible = "ti,wl1835";
> > + reg = <2>;
>
>
> Best regards,
> Krzysztof
>
On 19/07/2023 20:57, James Hilliard wrote:
> On Wed, Jul 19, 2023 at 11:16 AM Krzysztof Kozlowski
> <krzysztof.kozlowski@linaro.org> wrote:
>>
>>> +
>>> +/ {
>>> + model = "Variscite i.MX6 QUAD/DUAL VAR-SOM-MX6";
>>> + compatible = "fsl,imx6q";
>>
>> That's not correct compatible. It's not Imx6 soc. It's a som.
>
> I'm confused, AFAIU the VAR-SOM-MX6 uses an imx6q SoC.
True, I should say - that's incomplete compatible. You claim here this
is imx6q. Not that it uses imx6q... Add your own compatible and document
all of them.
>
>>
>>> +...
>>> +
>>> + sound: sound {
>>> + compatible = "simple-audio-card";
>>> + simple-audio-card,name = "var-som-audio";
>>> + simple-audio-card,format = "i2s";
>>> + simple-audio-card,bitclock-master = <&sound_codec>;
>>> + simple-audio-card,frame-master = <&sound_codec>;
>>> + simple-audio-card,widgets = "Headphone", "Headphone Jack",
>>> + "Line", "Line In", "Microphone", "Mic Jack";
>>> + simple-audio-card,routing = "Headphone Jack", "HPLOUT",
>>> + "Headphone Jack", "HPROUT",
>>> + "LINE1L", "Line In",
>>> + "LINE1R", "Line In";
>>> +
>>> + sound_cpu: simple-audio-card,cpu {
>>> + sound-dai = <&ssi2>;
>>> + };
>>> +
>>> + sound_codec: simple-audio-card,codec {
>>> + sound-dai = <&tlv320aic3106>;
>>> + clocks = <&clks IMX6QDL_CLK_CKO>;
>>> + };
>>> + };
>>> +
>>> + wlan_bt_rfkill {
>>
>> No underscores in node names.
>>
>> Just "rfkill"
>>
>>
>>> + compatible = "rfkill-gpio";
>>> + name = "wlan_bt_rfkill";
>>> + type = <2>; /* bluetooth */
>>> + gpios = <&gpio6 18 GPIO_ACTIVE_HIGH>;
>>> + };
>>> +};
>>> +
>>
>> ...
>>
>>> + tlv320aic3106: codec@1b {
>>> + compatible = "ti,tlv320aic3106";
>>> + reg = <0x1b>;
>>> + #sound-dai-cells = <0>;
>>> + DRVDD-supply = <®_3p3v>;
>>> + AVDD-supply = <®_3p3v>;
>>> + IOVDD-supply = <®_3p3v>;
>>> + DVDD-supply = <®_3p3v>;
>>> + ai3x-ocmv = <0>;
>>> + reset-gpios = <&gpio4 5 GPIO_ACTIVE_LOW>;
>>> + ai3x-gpio-func = <
>>> + 0 /* AIC3X_GPIO1_FUNC_DISABLED */
>>> + 5 /* AIC3X_GPIO2_FUNC_DIGITAL_MIC_INPUT */
>>> + >;
>>> + };
>>> +};
>>> +
>>> +&iomuxc {
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&pinctrl_hog>;
>>> +
>>> + imx6qdl-var-som-mx6 {
>>> + pinctrl_hog: hoggrp {
>>> + fsl,pins = <
>>> + /* CTW6120 IRQ */
>>> + MX6QDL_PAD_EIM_DA7__GPIO3_IO07 0x80000000
>>> + /* SDMMC2 CD/WP */
>>> + MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x80000000
>>> + MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x80000000
>>> + >;
>>> + };
>>> +
>>> + pinctrl_audmux: audmux {
>>
>> It does not look like you tested the DTS against bindings. Please run
>> `make dtbs_check` (see
>> Documentation/devicetree/bindings/writing-schema.rst or
>> https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/
>> for instructions).
>>
>> AFAIR, all of them end with grp
>
> Ah, that's def throwing a bunch of warnings, although quite a few look
> to be existing
> issues in dependent dtsi files. I'll clean up what I can there.
>
>>
>>
>> ...
>>
>>> +
>>> +&usdhc3 {
>>> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
>>> + pinctrl-0 = <&pinctrl_usdhc3>;
>>> + pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
>>> + pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
>>> + bus-width = <4>;
>>> + vmmc-supply = <®_wl18xx_vmmc>;
>>> + non-removable;
>>> + wakeup-source;
>>> + keep-power-in-suspend;
>>> + cap-power-off-card;
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> + status = "okay";
>>> +
>>> + wlcore: wlcore@0 {
>>
>> Generic node names. Is this wifi?
>
> I think it also supports bluetooth technically, although that might be
> under a different node.
>
Bluetooths are usually under serial, so this is just wifi.
Best regards,
Krzysztof
new file mode 100644
@@ -0,0 +1,547 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Support for Variscite VAR-SOM-MX6 Module
+ *
+ * Copyright 2011 Linaro Ltd.
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ * Copyright (C) 2014-2016 Variscite, Ltd.
+ * Author: Donio Ron <ron.d@variscite.com>
+ * Copyright 2022 Bootlin
+ */
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include <dt-bindings/clock/imx6qdl-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
+
+/ {
+ model = "Variscite i.MX6 QUAD/DUAL VAR-SOM-MX6";
+ compatible = "fsl,imx6q";
+
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x40000000>;
+ };
+
+ reg_audio: regulator-audio {
+ compatible = "regulator-fixed";
+ regulator-name = "tlv320aic3x-supply";
+ enable-active-high;
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ touch_3v3_regulator: touch_3v3_regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "touch_3v3_supply";
+ regulator-always-on;
+ status = "okay";
+ };
+
+ reg_wl18xx_vmmc: regulator-wl18xx {
+ compatible = "regulator-fixed";
+ regulator-name = "vwl1807";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&gpio7 8 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ startup-delay-us = <70000>;
+ };
+
+ sound: sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "var-som-audio";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,bitclock-master = <&sound_codec>;
+ simple-audio-card,frame-master = <&sound_codec>;
+ simple-audio-card,widgets = "Headphone", "Headphone Jack",
+ "Line", "Line In", "Microphone", "Mic Jack";
+ simple-audio-card,routing = "Headphone Jack", "HPLOUT",
+ "Headphone Jack", "HPROUT",
+ "LINE1L", "Line In",
+ "LINE1R", "Line In";
+
+ sound_cpu: simple-audio-card,cpu {
+ sound-dai = <&ssi2>;
+ };
+
+ sound_codec: simple-audio-card,codec {
+ sound-dai = <&tlv320aic3106>;
+ clocks = <&clks IMX6QDL_CLK_CKO>;
+ };
+ };
+
+ wlan_bt_rfkill {
+ compatible = "rfkill-gpio";
+ name = "wlan_bt_rfkill";
+ type = <2>; /* bluetooth */
+ gpios = <&gpio6 18 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&cpu0 {
+ operating-points = <
+ /* kHz uV */
+ 1200000 1350000
+ 996000 1250000
+ 852000 1250000
+ 792000 1175000
+ 396000 1175000
+ >;
+
+ fsl,soc-operating-points = <
+ /* ARM kHz SOC-PU uV */
+ 1200000 1275000
+ 996000 1250000
+ 852000 1250000
+ 792000 1250000
+ 396000 1250000
+ >;
+};
+
+&audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ status = "okay";
+
+ ssi2 {
+ fsl,audmux-port = <1>;
+ fsl,port-config = <
+ (IMX_AUDMUX_V2_PTCR_SYN |
+ IMX_AUDMUX_V2_PTCR_TFSDIR |
+ IMX_AUDMUX_V2_PTCR_TFSEL(2) |
+ IMX_AUDMUX_V2_PTCR_TCLKDIR |
+ IMX_AUDMUX_V2_PTCR_TCSEL(2))
+ IMX_AUDMUX_V2_PDCR_RXDSEL(2)
+ >;
+ };
+
+ aud3 {
+ fsl,audmux-port = <2>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN
+ IMX_AUDMUX_V2_PDCR_RXDSEL(1)
+ >;
+ };
+};
+
+&ecspi3 {
+ fsl,spi-num-chipselects = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi3>;
+ cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii";
+ phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ fsl,magic-packet;
+ status = "okay";
+};
+
+&gpc {
+ fsl,ldo-bypass = <1>;
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+
+ pmic@8 {
+ pinctrl-names = "default";
+ compatible = "fsl,pfuze100";
+ reg = <0x08>;
+
+ regulators {
+ sw1a_reg: sw1ab {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw1c_reg: sw1c {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3a_reg: sw3a {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3950000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3b_reg: sw3b {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3950000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw4_reg: sw4 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3950000>;
+ };
+
+ snvs_reg: vsnvs {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vref_reg: vrefddr {
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vgen1_reg: vgen1 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ vgen2_reg: vgen2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ vgen3_reg: vgen3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vgen4_reg: vgen4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vgen5_reg: vgen5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vgen6_reg: vgen6 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ };
+ };
+
+ tlv320aic3106: codec@1b {
+ compatible = "ti,tlv320aic3106";
+ reg = <0x1b>;
+ #sound-dai-cells = <0>;
+ DRVDD-supply = <®_3p3v>;
+ AVDD-supply = <®_3p3v>;
+ IOVDD-supply = <®_3p3v>;
+ DVDD-supply = <®_3p3v>;
+ ai3x-ocmv = <0>;
+ reset-gpios = <&gpio4 5 GPIO_ACTIVE_LOW>;
+ ai3x-gpio-func = <
+ 0 /* AIC3X_GPIO1_FUNC_DISABLED */
+ 5 /* AIC3X_GPIO2_FUNC_DIGITAL_MIC_INPUT */
+ >;
+ };
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ imx6qdl-var-som-mx6 {
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ /* CTW6120 IRQ */
+ MX6QDL_PAD_EIM_DA7__GPIO3_IO07 0x80000000
+ /* SDMMC2 CD/WP */
+ MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x80000000
+ MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x80000000
+ >;
+ };
+
+ pinctrl_audmux: audmux {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
+ MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
+ MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
+ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
+ /* Audio Clock */
+ MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0
+ >;
+ };
+
+ pinctrl_bt: bt {
+ fsl,pins = <
+ /* Bluetooth/wifi enable */
+ MX6QDL_PAD_SD3_DAT6__GPIO6_IO18 0x1b0b1
+ /* Wifi Slow Clock */
+ MX6QDL_PAD_ENET_RXD0__OSC32K_32K_OUT 0x000b0
+ >;
+ };
+
+ pinctrl_ecspi3: ecspi3grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1
+ MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1
+ MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
+ >;
+ };
+
+ pinctrl_enet_irq: enetirqgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_6__ENET_IRQ 0x000b1
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1
+ MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_16__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_pmic: pmicgrp {
+ fsl,pins = <
+ /* PMIC INT */
+ MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x80000000
+ >;
+ };
+
+ pinctrl_pwm2: pwm2grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT9__PWM2_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_DAT4__UART2_RX_DATA 0x1b0b1
+ MX6QDL_PAD_SD3_DAT5__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D28__UART2_CTS_B 0x1b0b1
+ MX6QDL_PAD_EIM_D29__UART2_RTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17069
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10069
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17069
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17069
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17069
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17069
+ /* WL_EN */
+ MX6QDL_PAD_SD3_DAT7__GPIO6_IO17 0x13059
+ /* WL_IRQ */
+ MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x13059
+ >;
+ };
+
+ pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170B9
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100B9
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170B9
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170B9
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170B9
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170B9
+ /* WL_EN */
+ MX6QDL_PAD_SD3_DAT7__GPIO6_IO17 0x130B9
+ /* WL_IRQ */
+ MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x130B9
+ >;
+ };
+
+ pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170F9
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100F9
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170F9
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170F9
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170F9
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170F9
+ /* WL_EN */
+ MX6QDL_PAD_SD3_DAT7__GPIO6_IO17 0x130F9
+ /* WL_IRQ */
+ MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x130F9
+ >;
+ };
+
+ pinctrl_gpmi_nand: gpminandgrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
+ MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
+ MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
+ MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1
+ MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb0b1
+ MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
+ MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
+ MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
+ MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
+ MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
+ MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
+ MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
+ MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
+ MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
+ MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
+ MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
+ >;
+ };
+ };
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>;
+ status = "okay";
+};
+
+®_arm {
+ vin-supply = <&sw1a_reg>;
+};
+
+®_pu {
+ vin-supply = <&sw1c_reg>;
+};
+
+®_soc {
+ vin-supply = <&sw1c_reg>;
+};
+
+&snvs_poweroff {
+ status = "okay";
+};
+
+&ssi2 {
+ fsl,mode = "i2s-slave";
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2 &pinctrl_bt>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpmi_nand>;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+ bus-width = <4>;
+ vmmc-supply = <®_wl18xx_vmmc>;
+ non-removable;
+ wakeup-source;
+ keep-power-in-suspend;
+ cap-power-off-card;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ wlcore: wlcore@0 {
+ compatible = "ti,wl1835";
+ reg = <2>;
+ interrupt-parent = <&gpio6>;
+ interrupts = <17 IRQ_TYPE_EDGE_RISING>;
+ ref-clock-frequency = <38400000>;
+ };
+};
+
+®_vdd1p1 {
+ vin-supply = <&vgen5_reg>;
+};
+
+®_vdd2p5 {
+ vin-supply = <&vgen5_reg>;
+};