diff mbox series

[v2,8/8] ARM: dts: stm32: Add Octavo OSD32MP1-RED board

Message ID	20230621063339.1361073-8-sean@geanix.com
State	New
Headers	Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 2620:137:e000::1:20 as permitted sender) client-ip=2620:137:e000::1:20; From: Sean Nyekjaer <sean@geanix.com> To: a.fatoum@pengutronix.de, Rob Herring <robh+dt@kernel.org>, Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>, Conor Dooley <conor+dt@kernel.org>, Maxime Coquelin <mcoquelin.stm32@gmail.com>, Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Sean Nyekjaer <sean@geanix.com>, dantuguf14105@gmail.com, Olivier Moysan <olivier.moysan@foss.st.com>, devicetree@vger.kernel.org, linux-stm32@st-md-mailman.stormreply.com, linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org Subject: [PATCH v2 8/8] ARM: dts: stm32: Add Octavo OSD32MP1-RED board Date: Wed, 21 Jun 2023 08:33:38 +0200 Message-Id: <20230621063339.1361073-8-sean@geanix.com> In-Reply-To: <20230621063339.1361073-1-sean@geanix.com> References: <20230621063339.1361073-1-sean@geanix.com> MIME-Version: 1.0 Content-Transfer-Encoding: 8bit Precedence: bulk
Series	[v2,1/8] ARM: dts: stm32: Add alternate pinmux for i2s pins \| [v2,1/8] ARM: dts: stm32: Add alternate pinmux for i2s pins [v2,2/8] ARM: dts: stm32: Add alternate pinmux for ldtc pins [v2,3/8] ARM: dts: stm32: Add alternate pinmux for can pins [v2,4/8] ARM: dts: stm32: osd32: fix ldo1 not required to be always-on [v2,5/8] ARM: dts: stm32: osd32: fix ldo2 not required to be always-on [v2,6/8] ARM: dts: stm32: osd32: fix ldo6 not required to be always-on [v2,7/8] dt-bindings: arm: stm32: add extra SiP compatible for oct,stm32mp157c-osd32-red [v2,8/8] ARM: dts: stm32: Add Octavo OSD32MP1-RED board

Commit Message

Sean Nyekjaer June 21, 2023, 6:33 a.m. UTC

  Add support for the Octavo OSD32MP1-RED development board.

General features:
 - STM32MP157C
 - 512MB DDR3
 - CAN-FD
 - HDMI
 - USB-C OTG
 - UART

Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Olivier Moysan <olivier.moysan@foss.st.com>
---
Changes since v1:
 - Fixed comments from Ahmad

 .../arm/boot/dts/stm32mp157c-osd32mp1-red.dts | 226 ++++++++++++++++++
 1 file changed, 226 insertions(+)
 create mode 100644 arch/arm/boot/dts/stm32mp157c-osd32mp1-red.dts

Comments

Alexandre TORGUE July 11, 2023, 1 p.m. UTC | #1

Hi Sean

On 6/21/23 08:33, Sean Nyekjaer wrote:
> Add support for the Octavo OSD32MP1-RED development board.
> 
> General features:
>   - STM32MP157C
>   - 512MB DDR3
>   - CAN-FD
>   - HDMI
>   - USB-C OTG
>   - UART
> 
> Signed-off-by: Sean Nyekjaer <sean@geanix.com>
> Reviewed-by: Olivier Moysan <olivier.moysan@foss.st.com>
> ---

You must update Makefile if you want I build it :). In the same time you 
could also ordering your phandle nodes by alphabetic order. It makes the 
file easier to read.

Regards
Alex

> Changes since v1:
>   - Fixed comments from Ahmad
> 
>   .../arm/boot/dts/stm32mp157c-osd32mp1-red.dts | 226 ++++++++++++++++++
>   1 file changed, 226 insertions(+)
>   create mode 100644 arch/arm/boot/dts/stm32mp157c-osd32mp1-red.dts
> 
> diff --git a/arch/arm/boot/dts/stm32mp157c-osd32mp1-red.dts b/arch/arm/boot/dts/stm32mp157c-osd32mp1-red.dts
> new file mode 100644
> index 000000000000..f840b7faf02a
> --- /dev/null
> +++ b/arch/arm/boot/dts/stm32mp157c-osd32mp1-red.dts
> @@ -0,0 +1,226 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
> +/*
> + * Copyright (C) Geanix ApS 2023 - All Rights Reserved
> + * Author: Sean Nyekjaer <sean@geanix.com>
> + */
> +
> +/dts-v1/;
> +
> +#include "stm32mp157.dtsi"
> +#include "stm32mp15xc.dtsi"
> +#include "stm32mp15xx-osd32.dtsi"
> +#include "stm32mp15xxac-pinctrl.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/pinctrl/stm32-pinfunc.h>
> +
> +/ {
> +	model = "Octavo OSD32MP1 RED board";
> +	compatible = "oct,stm32mp157c-osd32-red", "oct,stm32mp15xx-osd32", "st,stm32mp157";
> +
> +	aliases {
> +		serial0 = &uart4;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	led-controller-0 {
> +		compatible = "gpio-leds";
> +
> +		led-0 {
> +			label = "heartbeat";
> +			gpios = <&gpiod 11 GPIO_ACTIVE_HIGH>;
> +			linux,default-trigger = "heartbeat";
> +		};
> +	};
> +};
> +
> +&ethernet0 {
> +	status = "okay";
> +	pinctrl-0 = <&ethernet0_rgmii_pins_a>;
> +	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_a>;
> +	pinctrl-names = "default", "sleep";
> +	phy-mode = "rgmii-id";
> +	max-speed = <1000>;
> +	phy-handle = <&phy0>;
> +	st,eth-clk-sel;
> +
> +	mdio0 {
> +		compatible = "snps,dwmac-mdio";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		phy0: ethernet-phy@3 {
> +			reg = <3>;
> +		};
> +	};
> +};
> +
> +
> +&i2s2 {
> +	clocks = <&rcc SPI2>, <&rcc SPI2_K>, <&rcc CK_PER>, <&rcc PLL3_R>;
> +	clock-names = "pclk", "i2sclk", "x8k", "x11k";
> +	pinctrl-names = "default", "sleep";
> +	pinctrl-0 = <&i2s2_pins_b>;
> +	pinctrl-1 = <&i2s2_sleep_pins_b>;
> +	status = "okay";
> +
> +	i2s2_port: port {
> +		i2s2_endpoint: endpoint {
> +			remote-endpoint = <&sii9022_tx_endpoint>;
> +			format = "i2s";
> +			mclk-fs = <256>;
> +		};
> +	};
> +};
> +
> +&iwdg2 {
> +	timeout-sec = <32>;
> +	status = "okay";
> +};
> +
> +&pwr_regulators {
> +	vdd-supply = <&vdd>;
> +	vdd_3v3_usbfs-supply = <&vdd_usb>;
> +};
> +
> +&ltdc {
> +	status = "okay";
> +
> +	port {
> +		ltdc_ep0_out: endpoint@0 {
> +			reg = <0>;
> +			remote-endpoint = <&sii9022_in>;
> +		};
> +	};
> +};
> +
> +&i2c1 {
> +	pinctrl-names = "default", "sleep";
> +	pinctrl-0 = <&i2c1_pins_a>;
> +	pinctrl-1 = <&i2c1_sleep_pins_a>;
> +	status = "okay";
> +	i2c-scl-rising-time-ns = <100>;
> +	i2c-scl-falling-time-ns = <7>;
> +	/delete-property/dmas;
> +	/delete-property/dma-names;
> +
> +	hdmi-transmitter@39 {
> +		compatible = "sil,sii9022";
> +		reg = <0x39>;
> +		reset-gpios = <&gpiog 0 GPIO_ACTIVE_LOW>;
> +		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
> +		interrupt-parent = <&gpiog>;
> +		pinctrl-names = "default", "sleep";
> +		pinctrl-0 = <&ltdc_pins_e>;
> +		pinctrl-1 = <&ltdc_sleep_pins_e>;
> +		status = "okay";
> +
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port@0 {
> +				reg = <0>;
> +				sii9022_in: endpoint {
> +					remote-endpoint = <&ltdc_ep0_out>;
> +				};
> +			};
> +
> +			port@1 {
> +				reg = <1>;
> +				sii9022_tx_endpoint: endpoint {
> +					remote-endpoint = <&i2s2_endpoint>;
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +&sdmmc1 {
> +	pinctrl-names = "default", "opendrain", "sleep";
> +	pinctrl-0 = <&sdmmc1_b4_pins_a>;
> +	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
> +	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
> +	cd-gpios = <&gpioe 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> +	disable-wp;
> +	st,neg-edge;
> +	bus-width = <4>;
> +	vmmc-supply = <&v3v3>;
> +	status = "okay";
> +};
> +
> +&sdmmc2 {
> +	pinctrl-names = "default", "opendrain", "sleep";
> +	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_d>;
> +	pinctrl-1 = <&sdmmc2_b4_od_pins_a>;
> +	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_d>;
> +	non-removable;
> +	no-sd;
> +	no-sdio;
> +	st,neg-edge;
> +	bus-width = <8>;
> +	vmmc-supply = <&v3v3>;
> +	vqmmc-supply = <&vdd>;
> +	mmc-ddr-3_3v;
> +	status = "okay";
> +};
> +
> +&uart4 {
> +	pinctrl-names = "default", "sleep", "idle";
> +	pinctrl-0 = <&uart4_pins_a>;
> +	pinctrl-1 = <&uart4_sleep_pins_a>;
> +	pinctrl-2 = <&uart4_idle_pins_a>;
> +	/delete-property/dmas;
> +	/delete-property/dma-names;
> +	status = "okay";
> +};
> +
> +&m_can1 {
> +	pinctrl-names = "default", "sleep";
> +	pinctrl-0 = <&m_can1_pins_d>;
> +	pinctrl-1 = <&m_can1_sleep_pins_d>;
> +	status = "okay";
> +};
> +
> +&usbh_ehci {
> +	phys = <&usbphyc_port0>;
> +	phy-names = "usb";
> +	status = "okay";
> +};
> +
> +&usbh_ohci {
> +	phys = <&usbphyc_port0>;
> +	phy-names = "usb";
> +	status = "okay";
> +};
> +
> +&usbotg_hs {
> +	vbus-supply = <&vbus_otg>;
> +};
> +
> +&usbphyc {
> +	status = "okay";
> +};
> +
> +&usbphyc_port0 {
> +	phy-supply = <&vdd_usb>;
> +};
> +
> +&usbphyc_port1 {
> +	phy-supply = <&vdd_usb>;
> +};
> +
> +&rtc {
> +	status = "okay";
> +};
> +
> +&crc1 {
> +	status = "okay";
> +};
> +
> +&dts {
> +	status = "okay";
> +};

diff mbox series

Patch

diff --git a/arch/arm/boot/dts/stm32mp157c-osd32mp1-red.dts b/arch/arm/boot/dts/stm32mp157c-osd32mp1-red.dts
new file mode 100644
index 000000000000..f840b7faf02a
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157c-osd32mp1-red.dts
@@ -0,0 +1,226 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) Geanix ApS 2023 - All Rights Reserved
+ * Author: Sean Nyekjaer <sean@geanix.com>
+ */
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-osd32.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/stm32-pinfunc.h>
+
+/ {
+	model = "Octavo OSD32MP1 RED board";
+	compatible = "oct,stm32mp157c-osd32-red", "oct,stm32mp15xx-osd32", "st,stm32mp157";
+
+	aliases {
+		serial0 = &uart4;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	led-controller-0 {
+		compatible = "gpio-leds";
+
+		led-0 {
+			label = "heartbeat";
+			gpios = <&gpiod 11 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&ethernet0 {
+	status = "okay";
+	pinctrl-0 = <&ethernet0_rgmii_pins_a>;
+	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_a>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rgmii-id";
+	max-speed = <1000>;
+	phy-handle = <&phy0>;
+	st,eth-clk-sel;
+
+	mdio0 {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy0: ethernet-phy@3 {
+			reg = <3>;
+		};
+	};
+};
+
+
+&i2s2 {
+	clocks = <&rcc SPI2>, <&rcc SPI2_K>, <&rcc CK_PER>, <&rcc PLL3_R>;
+	clock-names = "pclk", "i2sclk", "x8k", "x11k";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2s2_pins_b>;
+	pinctrl-1 = <&i2s2_sleep_pins_b>;
+	status = "okay";
+
+	i2s2_port: port {
+		i2s2_endpoint: endpoint {
+			remote-endpoint = <&sii9022_tx_endpoint>;
+			format = "i2s";
+			mclk-fs = <256>;
+		};
+	};
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&pwr_regulators {
+	vdd-supply = <&vdd>;
+	vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&ltdc {
+	status = "okay";
+
+	port {
+		ltdc_ep0_out: endpoint@0 {
+			reg = <0>;
+			remote-endpoint = <&sii9022_in>;
+		};
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c1_pins_a>;
+	pinctrl-1 = <&i2c1_sleep_pins_a>;
+	status = "okay";
+	i2c-scl-rising-time-ns = <100>;
+	i2c-scl-falling-time-ns = <7>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	hdmi-transmitter@39 {
+		compatible = "sil,sii9022";
+		reg = <0x39>;
+		reset-gpios = <&gpiog 0 GPIO_ACTIVE_LOW>;
+		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-parent = <&gpiog>;
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&ltdc_pins_e>;
+		pinctrl-1 = <&ltdc_sleep_pins_e>;
+		status = "okay";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				sii9022_in: endpoint {
+					remote-endpoint = <&ltdc_ep0_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+				sii9022_tx_endpoint: endpoint {
+					remote-endpoint = <&i2s2_endpoint>;
+				};
+			};
+		};
+	};
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	cd-gpios = <&gpioe 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_d>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_d>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	st,neg-edge;
+	bus-width = <8>;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&vdd>;
+	mmc-ddr-3_3v;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&m_can1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can1_pins_d>;
+	pinctrl-1 = <&m_can1_sleep_pins_d>;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	phy-names = "usb";
+	status = "okay";
+};
+
+&usbh_ohci {
+	phys = <&usbphyc_port0>;
+	phy-names = "usb";
+	status = "okay";
+};
+
+&usbotg_hs {
+	vbus-supply = <&vbus_otg>;
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
+
+&rtc {
+	status = "okay";
+};
+
+&crc1 {
+	status = "okay";
+};
+
+&dts {
+	status = "okay";
+};