diff mbox series

[v2,2/4] arm64: dts: qcom: sm6115p-j606f: Hook up display

Message ID 20230620-topic-gpu_tablet_disp-v2-2-0538ea1beb0b@linaro.org
State New
Headers
Series A610 enablement, J606F display |

Commit Message

Konrad Dybcio June 21, 2023, 11:21 a.m. UTC 
  Enable the required nodes, add the required pins and tweak a
regulator to enable non-simplefb display on the Tab P11.

Do note that there exists a second SKU with a different panel+touch
combo, but due to insufficient information, that will need to be
handled separately.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts | 57 +++++++++++++++++++++--
 1 file changed, 52 insertions(+), 5 deletions(-)

Comments

Dmitry Baryshkov June 21, 2023, 2:12 p.m. UTC | #1 
On Wed, 21 Jun 2023 at 14:22, Konrad Dybcio <konrad.dybcio@linaro.org> wrote:
>
> Enable the required nodes, add the required pins and tweak a
> regulator to enable non-simplefb display on the Tab P11.
>
> Do note that there exists a second SKU with a different panel+touch
> combo, but due to insufficient information, that will need to be
> handled separately.
>
> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts | 57 +++++++++++++++++++++--
>  1 file changed, 52 insertions(+), 5 deletions(-)

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts b/arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts
index 81fdcaf48926..667273ae0553 100644
--- a/arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts
+++ b/arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts
@@ -65,9 +65,41 @@  ramoops@ffc00000 {
 	};
 };
 
-&dispcc {
-	/* HACK: disable until a panel driver is ready to retain simplefb */
-	status = "disabled";
+&mdss {
+	status = "okay";
+};
+
+&mdss_dsi0 {
+	vdda-supply = <&pm6125_l18>;
+	status = "okay";
+
+	panel: panel@0 {
+		compatible = "lenovo,j606f-boe-nt36523w", "novatek,nt36523w";
+		reg = <0>;
+
+		reset-gpios = <&tlmm 82 GPIO_ACTIVE_LOW>;
+		vddio-supply = <&pm6125_l9>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&te_active &mdss_dsi_active>;
+
+		rotation = <180>; /* Yep, it's mounted upside down! */
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&mdss_dsi0_out>;
+			};
+		};
+	};
+};
+
+&mdss_dsi0_out {
+	data-lanes = <0 1 2 3>;
+	remote-endpoint = <&panel_in>;
+};
+
+&mdss_dsi0_phy {
+	status = "okay";
 };
 
 &pm6125_gpios {
@@ -212,8 +244,9 @@  pm6125_l17: l17 {
 		};
 
 		pm6125_l18: l18 {
-			regulator-min-microvolt = <1104000>;
-			regulator-max-microvolt = <1312000>;
+			/* 1.104V-1.312V fixed @ 1.232V for DSIPHY */
+			regulator-min-microvolt = <1232000>;
+			regulator-max-microvolt = <1232000>;
 		};
 
 		pm6125_l19: l19 {
@@ -282,6 +315,20 @@  sdc2_gate_pin: sdc2-gate-state {
 		bias-pull-up;
 		output-high;
 	};
+
+	te_active: te-active-state {
+		pins = "gpio81";
+		function = "mdp_vsync";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	mdss_dsi_active: dsi-active-state {
+		pins = "gpio82";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
 };
 
 &ufs_mem_hc {