[v2,3/4] arm64: dts: qcom: sm8250-pdx203: Configure SLG51000 PMIC
Commit Message
Xperia 1 II / PRO use the Dialog SLG51000 PMIC for powering some camera
sensors. Add the required nodes to support it and remove its remnants
from -edo.dtsi, as it's absent on 5 II.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
.../dts/qcom/sm8250-sony-xperia-edo-pdx203.dts | 131 +++++++++++++++++++++
.../boot/dts/qcom/sm8250-sony-xperia-edo.dtsi | 7 --
2 files changed, 131 insertions(+), 7 deletions(-)
@@ -15,6 +15,123 @@ / {
/delete-node/ &vreg_l7f_1p8;
+&i2c5 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ pmic@75 {
+ compatible = "dlg,slg51000";
+ reg = <0x75>;
+ dlg,cs-gpios = <&tlmm 69 GPIO_ACTIVE_HIGH>;
+ vin5-supply = <&vreg_s1f_1p2>;
+ vin6-supply = <&vreg_s1f_1p2>;
+
+ pinctrl-0 = <&cam_pwr_b_cs>;
+ pinctrl-names = "default";
+
+ regulators {
+ slg51000_1_ldo1: ldo1 {
+ regulator-name = "slg51000_b_ldo1";
+ regulator-min-microvolt = <2400000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ slg51000_1_ldo2: ldo2 {
+ regulator-name = "slg51000_b_ldo2";
+ regulator-min-microvolt = <2400000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ slg51000_1_ldo3: ldo3 {
+ regulator-name = "slg51000_b_ldo3";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3750000>;
+ };
+
+ slg51000_1_ldo4: ldo4 {
+ regulator-name = "slg51000_b_ldo4";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3750000>;
+ };
+
+ slg51000_1_ldo5: ldo5 {
+ regulator-name = "slg51000_b_ldo5";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ slg51000_1_ldo6: ldo6 {
+ regulator-name = "slg51000_b_ldo6";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ slg51000_1_ldo7: ldo7 {
+ regulator-name = "slg51000_b_ldo7";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3750000>;
+ };
+ };
+ };
+};
+
+&i2c15 {
+ pmic@75 {
+ compatible = "dlg,slg51000";
+ reg = <0x75>;
+ dlg,cs-gpios = <&tlmm 71 GPIO_ACTIVE_HIGH>;
+ vin5-supply = <&vreg_l2f_1p3>;
+ vin6-supply = <&vreg_l2f_1p3>;
+
+ pinctrl-0 = <&cam_pwr_a_cs>;
+ pinctrl-names = "default";
+
+ regulators {
+ slg51000_0_ldo1: ldo1 {
+ regulator-name = "slg51000_a_ldo1";
+ regulator-min-microvolt = <2400000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ slg51000_0_ldo2: ldo2 {
+ regulator-name = "slg51000_a_ldo2";
+ regulator-min-microvolt = <2400000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ slg51000_0_ldo3: ldo3 {
+ regulator-name = "slg51000_a_ldo3";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3750000>;
+ };
+
+ slg51000_0_ldo4: ldo4 {
+ regulator-name = "slg51000_a_ldo4";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3750000>;
+ };
+
+ slg51000_0_ldo5: ldo5 {
+ regulator-name = "slg51000_a_ldo5";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ slg51000_0_ldo6: ldo6 {
+ regulator-name = "slg51000_a_ldo6";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ slg51000_0_ldo7: ldo7 {
+ regulator-name = "slg51000_a_ldo7";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3750000>;
+ };
+ };
+ };
+};
+
&pm8009_gpios {
gpio-line-names = "NC", /* GPIO_1 */
"CAM_PWR_LD_EN",
@@ -246,4 +363,18 @@ &tlmm {
"HST_BLE_SNS_UART6_RX",
"HST_WLAN_UART_TX",
"HST_WLAN_UART_RX";
+
+ cam_pwr_b_cs: cam-pwr-b-state {
+ pins = "gpio69";
+ drive-strength = <2>;
+ bias-disable;
+ output-low;
+ };
+
+ cam_pwr_a_cs: cam-pwr-a-state {
+ pins = "gpio71";
+ drive-strength = <2>;
+ bias-disable;
+ output-low;
+ };
};
@@ -486,13 +486,6 @@ cs35l41_r: speaker-amp@41 {
};
};
-&i2c5 {
- status = "okay";
- clock-frequency = <400000>;
-
- /* Dialog SLG51000 CMIC @ 75 */
-};
-
&i2c9 {
status = "okay";
clock-frequency = <400000>;