@@ -573,6 +573,15 @@ config REGULATOR_MAX77650
Semiconductor. This device has a SIMO with three independent
power rails and an LDO.
+config REGULATOR_MAX77857
+ tristate "ADI MAX77857/MAX77831 regulator support"
+ depends on I2C
+ help
+ This driver controls a ADI MAX77857 and MAX77831 regulators.
+ via I2C bus. MAX77857 and MAX77831 are high efficiency buck-boost
+ converters with input voltage range (2.5V to 16V). Say Y here to
+ enable the regulator driver
+
config REGULATOR_MAX8649
tristate "Maxim 8649 voltage regulator"
depends on I2C
@@ -85,6 +85,7 @@ obj-$(CONFIG_REGULATOR_MAX77686) += max77686-regulator.o
obj-$(CONFIG_REGULATOR_MAX77693) += max77693-regulator.o
obj-$(CONFIG_REGULATOR_MAX77802) += max77802-regulator.o
obj-$(CONFIG_REGULATOR_MAX77826) += max77826-regulator.o
+obj-$(CONFIG_REGULATOR_MAX77857) += max77857-regulator.o
obj-$(CONFIG_REGULATOR_MC13783) += mc13783-regulator.o
obj-$(CONFIG_REGULATOR_MC13892) += mc13892-regulator.o
obj-$(CONFIG_REGULATOR_MC13XXX_CORE) += mc13xxx-regulator-core.o
new file mode 100644
@@ -0,0 +1,382 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include <linux/bitfield.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/of_regulator.h>
+#include <linux/util_macros.h>
+
+#define MAX77857_REG_INT_SRC 0x10
+#define MAX77857_REG_INT_MASK 0x11
+#define MAX77857_REG_CONT1 0x12
+#define MAX77857_REG_CONT2 0x13
+#define MAX77857_REG_CONT3 0x14
+
+#define MAX77857_INT_SRC_OCP BIT(0)
+#define MAX77857_INT_SRC_THS BIT(1)
+#define MAX77857_INT_SRC_HARDSHORT BIT(2)
+#define MAX77857_INT_SRC_OVP BIT(3)
+#define MAX77857_INT_SRC_POK BIT(4)
+
+#define MAX77857_ILIM_MASK GENMASK(2, 0)
+#define MAX77857_CONT1_FREQ GENMASK(4, 3)
+#define MAX77857_CONT3_FPWM BIT(5)
+
+enum max77857_id {
+ ID_MAX77831 = 1,
+ ID_MAX77857,
+};
+
+static bool max77857_volatile_reg(struct device *dev, unsigned int reg)
+{
+ enum max77857_id id = (enum max77857_id)dev_get_drvdata(dev);
+
+ switch (id) {
+ case ID_MAX77831:
+ case ID_MAX77857:
+ return reg == MAX77857_REG_INT_SRC;
+ default:
+ return true;
+ }
+}
+
+struct regmap_config max77857_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .cache_type = REGCACHE_RBTREE,
+ .volatile_reg = max77857_volatile_reg,
+};
+
+static int max77857_get_status(struct regulator_dev *rdev)
+{
+ unsigned int val;
+ int ret;
+
+ ret = regmap_read(rdev->regmap, MAX77857_REG_INT_SRC, &val);
+ if (ret)
+ return ret;
+
+ if (FIELD_GET(MAX77857_INT_SRC_POK, val))
+ return REGULATOR_STATUS_ON;
+
+ return REGULATOR_STATUS_ERROR;
+}
+
+static unsigned int max77857_get_mode(struct regulator_dev *rdev)
+{
+ enum max77857_id id = (enum max77857_id)rdev_get_drvdata(rdev);
+ unsigned int regval;
+ int ret;
+
+ switch (id) {
+ case ID_MAX77831:
+ case ID_MAX77857:
+ ret = regmap_read(rdev->regmap, MAX77857_REG_CONT3, ®val);
+ if (ret)
+ return ret;
+
+ if (FIELD_GET(MAX77857_CONT3_FPWM, regval))
+ return REGULATOR_MODE_FAST;
+
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return REGULATOR_MODE_NORMAL;
+}
+
+static int max77857_set_mode(struct regulator_dev *rdev, unsigned int mode)
+{
+ enum max77857_id id = (enum max77857_id)rdev_get_drvdata(rdev);
+ unsigned int reg, val;
+
+ switch (id) {
+ case ID_MAX77831:
+ case ID_MAX77857:
+ reg = MAX77857_REG_CONT3;
+ val = MAX77857_CONT3_FPWM;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ switch (mode) {
+ case REGULATOR_MODE_FAST:
+ return regmap_set_bits(rdev->regmap, reg, val);
+ case REGULATOR_MODE_NORMAL:
+ return regmap_clear_bits(rdev->regmap, reg, val);
+ default:
+ return -EINVAL;
+ }
+}
+
+static int max77857_get_error_flags(struct regulator_dev *rdev,
+ unsigned int *flags)
+{
+ unsigned int val;
+ int ret;
+
+ ret = regmap_read(rdev->regmap, MAX77857_REG_INT_SRC, &val);
+ if (ret)
+ return ret;
+
+ *flags = 0;
+
+ if (FIELD_GET(MAX77857_INT_SRC_OVP, val))
+ *flags |= REGULATOR_ERROR_OVER_VOLTAGE_WARN;
+
+ if (FIELD_GET(MAX77857_INT_SRC_OCP, val) ||
+ FIELD_GET(MAX77857_INT_SRC_HARDSHORT, val))
+ *flags |= REGULATOR_ERROR_OVER_CURRENT;
+
+ if (FIELD_GET(MAX77857_INT_SRC_THS, val))
+ *flags |= REGULATOR_ERROR_OVER_TEMP;
+
+ if (!FIELD_GET(MAX77857_INT_SRC_POK, val))
+ *flags |= REGULATOR_ERROR_FAIL;
+
+ return 0;
+}
+
+static const struct regulator_ops max77857_regulator_ops = {
+ .list_voltage = regulator_list_voltage_linear_range,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_ramp_delay = regulator_set_ramp_delay_regmap,
+ .get_status = max77857_get_status,
+ .set_mode = max77857_set_mode,
+ .get_mode = max77857_get_mode,
+ .get_error_flags = max77857_get_error_flags,
+};
+
+static struct linear_range max77857_lin_ranges[] = {
+ REGULATOR_LINEAR_RANGE(4485000, 0x3D, 0xCC, 73500)
+};
+
+static const unsigned int max77857_switch_freq[] = {
+ 1200000, 1500000, 1800000, 2100000
+};
+
+static const unsigned int max77857_ramp_table[2][4] = {
+ { 1333, 667, 333, 227 }, /* when switch freq is 1.8MHz or 2.1MHz */
+ { 1166, 667, 333, 167 }, /* when switch freq is 1.2MHz or 1.5MHz */
+};
+
+static struct regulator_desc max77857_regulator_desc = {
+ .ops = &max77857_regulator_ops,
+ .name = "max77857",
+ .linear_ranges = max77857_lin_ranges,
+ .n_linear_ranges = ARRAY_SIZE(max77857_lin_ranges),
+ .vsel_mask = 0xFF,
+ .vsel_reg = MAX77857_REG_CONT2,
+ .ramp_delay_table = max77857_ramp_table[0],
+ .n_ramp_values = ARRAY_SIZE(max77857_ramp_table[0]),
+ .ramp_reg = MAX77857_REG_CONT3,
+ .ramp_mask = GENMASK(1, 0),
+ .ramp_delay = max77857_ramp_table[0][0],
+ .owner = THIS_MODULE,
+};
+
+static irqreturn_t max77857_irq_handler(int irq, void *data)
+{
+ struct regulator_dev *rdev = data;
+ enum max77857_id id = (enum max77857_id)rdev_get_drvdata(rdev);
+ struct device *dev = &rdev->dev;
+ unsigned long flags = 0;
+ unsigned int status;
+ int ret;
+
+ switch (id) {
+ case ID_MAX77831:
+ case ID_MAX77857:
+ ret = regmap_read(rdev->regmap, MAX77857_REG_INT_SRC, &status);
+ break;
+ default:
+ return IRQ_HANDLED;
+ }
+
+ if (ret) {
+ dev_err(dev, "cannot read status\n");
+ return IRQ_HANDLED;
+ }
+
+ if (FIELD_GET(MAX77857_INT_SRC_OCP, status)) {
+ flags |= REGULATOR_EVENT_OVER_CURRENT;
+ dev_dbg(dev, "regulator has been latched off due to overcurrent\n");
+ }
+
+ if (FIELD_GET(MAX77857_INT_SRC_THS, status)) {
+ flags |= REGULATOR_EVENT_OVER_TEMP;
+ dev_dbg(dev, "regulator has been latched off due to thermal shutdown\n");
+ }
+
+ if (FIELD_GET(MAX77857_INT_SRC_HARDSHORT, status)) {
+ flags |= REGULATOR_EVENT_OVER_CURRENT;
+ dev_dbg(dev, "regulator has been latched off due to output hardshort\n");
+ }
+
+ if (id == ID_MAX77831 || id == ID_MAX77857) {
+ if (FIELD_GET(MAX77857_INT_SRC_OVP, status)) {
+ flags |= REGULATOR_EVENT_OVER_VOLTAGE_WARN;
+ dev_dbg(dev, "output overvoltage detected\n");
+ }
+
+ if (FIELD_GET(MAX77857_INT_SRC_POK, status)) {
+ flags |= REGULATOR_EVENT_ENABLE;
+ dev_dbg(dev, "output power OK\n");
+ } else {
+ flags |= REGULATOR_EVENT_FAIL;
+ dev_err(dev, "regulator failed\n");
+ }
+ } else {
+ if (flags != 0)
+ flags |= REGULATOR_EVENT_FAIL;
+ }
+
+ regulator_notifier_call_chain(rdev, flags, NULL);
+
+ return IRQ_HANDLED;
+}
+
+static void max77857_calc_range(struct device *dev, enum max77857_id id)
+{
+ struct linear_range *range;
+ unsigned long vref_step;
+ u32 rtop = 0;
+ u32 rbot = 0;
+
+ device_property_read_u32(dev, "adi,rtop-ohms", &rtop);
+ device_property_read_u32(dev, "adi,rbot-ohms", &rbot);
+
+ if (!rbot || !rtop)
+ return;
+
+ switch (id) {
+ case ID_MAX77831:
+ case ID_MAX77857:
+ range = max77857_lin_ranges;
+ vref_step = 4900UL;
+ break;
+ }
+
+ range->step = DIV_ROUND_CLOSEST(vref_step * (rbot + rtop), rbot);
+ range->min = range->step * range->min_sel;
+}
+
+static int max77857_probe(struct i2c_client *client)
+{
+ const struct i2c_device_id *i2c_id;
+ struct device *dev = &client->dev;
+ struct regulator_config cfg = {};
+ struct regulator_dev *rdev;
+ struct regmap *regmap;
+ enum max77857_id id;
+ u32 switch_freq = 0;
+ int ret;
+
+ i2c_id = i2c_client_get_device_id(client);
+ if (!i2c_id)
+ return -EINVAL;
+
+ id = i2c_id->driver_data;
+
+ dev_set_drvdata(dev, (void *)id);
+
+ max77857_calc_range(dev, id);
+
+ regmap = devm_regmap_init_i2c(client, &max77857_regmap_config);
+ if (IS_ERR(regmap))
+ return dev_err_probe(dev, PTR_ERR(regmap),
+ "cannot initialize regmap\n");
+
+ device_property_read_u32(dev, "adi,switch-frequency-hz", &switch_freq);
+ if (switch_freq) {
+ switch_freq = find_closest(switch_freq, max77857_switch_freq,
+ ARRAY_SIZE(max77857_switch_freq));
+
+ if (id == ID_MAX77831 && switch_freq == 3)
+ switch_freq = 2;
+
+ switch (id) {
+ case ID_MAX77831:
+ case ID_MAX77857:
+ ret = regmap_update_bits(regmap, MAX77857_REG_CONT1,
+ MAX77857_CONT1_FREQ, switch_freq);
+
+ if (switch_freq >= 2)
+ break;
+
+ max77857_regulator_desc.ramp_delay_table = max77857_ramp_table[1];
+ max77857_regulator_desc.ramp_delay = max77857_ramp_table[1][0];
+ break;
+ }
+ if (ret)
+ return ret;
+ }
+
+ cfg.dev = dev;
+ cfg.driver_data = (void *)id;
+ cfg.regmap = regmap;
+ cfg.init_data = of_get_regulator_init_data(dev, dev->of_node,
+ &max77857_regulator_desc);
+ if (!cfg.init_data)
+ return -ENOMEM;
+
+ rdev = devm_regulator_register(dev, &max77857_regulator_desc, &cfg);
+ if (IS_ERR(rdev))
+ return dev_err_probe(dev, PTR_ERR(rdev),
+ "cannot register regulator\n");
+
+ if (client->irq) {
+ ret = devm_request_threaded_irq(dev, client->irq, NULL,
+ max77857_irq_handler,
+ IRQF_ONESHOT,
+ client->name, rdev);
+ if (ret)
+ return dev_err_probe(dev, ret, "cannot request irq\n");
+
+ /* enable interrupts */
+ switch (id) {
+ case ID_MAX77831:
+ case ID_MAX77857:
+ ret = regmap_write(regmap, MAX77857_REG_INT_MASK, 0x00);
+ break;
+ }
+
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+const struct i2c_device_id max77857_id[] = {
+ { "max77831", ID_MAX77831 },
+ { "max77857", ID_MAX77857 },
+ {}
+};
+
+static const struct of_device_id max77857_of_id[] = {
+ { .compatible = "adi,max77831", .data = (void *)ID_MAX77831 },
+ { .compatible = "adi,max77857", .data = (void *)ID_MAX77857 },
+ { }
+};
+
+struct i2c_driver max77857_driver = {
+ .driver = {
+ .name = "max77857",
+ .of_match_table = max77857_of_id,
+ },
+ .id_table = max77857_id,
+ .probe_new = max77857_probe,
+};
+module_i2c_driver(max77857_driver);
+
+MODULE_DESCRIPTION("Analog Devices MAX77857 Buck-Boost Converter Driver");
+MODULE_AUTHOR("Ibrahim Tilki <Ibrahim.Tilki@analog.com>");
+MODULE_AUTHOR("Okan Sahin <Okan.Sahin@analog.com>");
+MODULE_LICENSE("GPL");