[3/3] arm64: dts: qcom: sc8180x-flex5g: Wire up USB Type-C
Commit Message
Following the SC8180X Primus reference design, add pmic_glink and USB
Type-C wiring for battery manager, external display and orientation
switching.
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
---
.../boot/dts/qcom/sc8180x-lenovo-flex-5g.dts | 196 ++++++++++++++++++
1 file changed, 196 insertions(+)
@@ -45,6 +45,84 @@ lid {
};
};
+ pmic-glink {
+ compatible = "qcom,sc8180x-pmic-glink", "qcom,pmic-glink";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ connector@0 {
+ compatible = "usb-c-connector";
+ reg = <0>;
+ power-role = "dual";
+ data-role = "dual";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ pmic_glink_con0_hs: endpoint {
+ remote-endpoint = <&usb_prim_role_switch>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ pmic_glink_con0_ss: endpoint {
+ remote-endpoint = <&usb_prim_qmpphy_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ pmic_glink_con0_sbu: endpoint {
+ remote-endpoint = <&usbprim_sbu_mux>;
+ };
+ };
+ };
+ };
+
+ connector@1 {
+ compatible = "usb-c-connector";
+ reg = <1>;
+ power-role = "dual";
+ data-role = "dual";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+
+ pmic_glink_con1_hs: endpoint {
+ remote-endpoint = <&usb_sec_role_switch>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ pmic_glink_con1_ss: endpoint {
+ remote-endpoint = <&usb_sec_qmpphy_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ pmic_glink_con1_sbu: endpoint {
+ remote-endpoint = <&usbsec_sbu_mux>;
+ };
+ };
+ };
+ };
+ };
+
reserved-memory {
rmtfs_mem: rmtfs-region@85500000 {
compatible = "qcom,rmtfs-mem";
@@ -100,6 +178,44 @@ vreg_s4a_1p8: pm8150-s4-regulator {
vin-supply = <&vph_pwr>;
};
+
+ usbprim-sbu-mux {
+ compatible = "pericom,pi3usb102", "gpio-sbu-mux";
+
+ enable-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>;
+ select-gpios = <&tlmm 100 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&usbprim_sbu_default>;
+
+ mode-switch;
+ orientation-switch;
+
+ port {
+ usbprim_sbu_mux: endpoint {
+ remote-endpoint = <&pmic_glink_con0_sbu>;
+ };
+ };
+ };
+
+ usbsec-sbu-mux {
+ compatible = "pericom,pi3usb102", "gpio-sbu-mux";
+
+ enable-gpios = <&tlmm 188 GPIO_ACTIVE_LOW>;
+ select-gpios = <&tlmm 187 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&usbsec_sbu_default>;
+
+ mode-switch;
+ orientation-switch;
+
+ port {
+ usbsec_sbu_mux: endpoint {
+ remote-endpoint = <&pmic_glink_con1_sbu>;
+ };
+ };
+ };
};
&apps_rsc {
@@ -283,6 +399,24 @@ &mdss {
status = "okay";
};
+&mdss_dp0 {
+ status = "okay";
+};
+
+&mdss_dp0_out {
+ data-lanes = <0 1>;
+ remote-endpoint = <&usb_prim_qmpphy_dp_in>;
+};
+
+&mdss_dp1 {
+ status = "okay";
+};
+
+&mdss_dp1_out {
+ data-lanes = <0 1>;
+ remote-endpoint = <&usb_sec_qmpphy_dp_in>;
+};
+
&mdss_edp {
data-lanes = <0 1 2 3>;
@@ -419,6 +553,8 @@ &usb_prim_qmpphy {
vdda-phy-supply = <&vreg_l3c_1p2>;
vdda-pll-supply = <&vreg_l5e_0p88>;
+ orientation-switch;
+
status = "okay";
};
@@ -430,6 +566,18 @@ &usb_prim_dwc3 {
dr_mode = "host";
};
+&usb_prim_qmpphy_dp_in {
+ remote-endpoint = <&mdss_dp0_out>;
+};
+
+&usb_prim_qmpphy_out {
+ remote-endpoint = <&pmic_glink_con0_ss>;
+};
+
+&usb_prim_role_switch {
+ remote-endpoint = <&pmic_glink_con0_hs>;
+};
+
&usb_sec_hsphy {
vdda-pll-supply = <&vreg_l5e_0p88>;
vdda18-supply = <&vreg_l12a_1p8>;
@@ -442,9 +590,23 @@ &usb_sec_qmpphy {
vdda-phy-supply = <&vreg_l3c_1p2>;
vdda-pll-supply = <&vreg_l5e_0p88>;
+ orientation-switch;
+
status = "okay";
};
+&usb_sec_qmpphy_dp_in {
+ remote-endpoint = <&mdss_dp1_out>;
+};
+
+&usb_sec_qmpphy_out {
+ remote-endpoint = <&pmic_glink_con1_ss>;
+};
+
+&usb_sec_role_switch {
+ remote-endpoint = <&pmic_glink_con1_hs>;
+};
+
&usb_sec {
status = "okay";
};
@@ -560,6 +722,40 @@ wake-n-pins {
};
};
+ usbprim_sbu_default: usbprim-sbu-state {
+ oe-n-pins {
+ pins = "gpio152";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <16>;
+ output-high;
+ };
+
+ sel-pins {
+ pins = "gpio100";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <16>;
+ };
+ };
+
+ usbsec_sbu_default: usbsec-sbu-state {
+ oe-n-pins {
+ pins = "gpio188";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <16>;
+ output-high;
+ };
+
+ sel-pins {
+ pins = "gpio187";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <16>;
+ };
+ };
+
uart13_state: uart13-state {
cts-pins {
pins = "gpio43";