diff mbox series

[v4,3/4] riscv: dts: starfive: jh7110: Add PWM node and pins configuration

Message ID 20230601085154.36938-4-william.qiu@starfivetech.com
State New
Headers
Series StarFive's Pulse Width Modulation driver support |

Commit Message

William Qiu June 1, 2023, 8:51 a.m. UTC 
  Add StarFive JH7110 PWM controller node and add PWM pins configuration
on VisionFive 2 board.

Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: William Qiu <william.qiu@starfivetech.com>
---
 .../jh7110-starfive-visionfive-2.dtsi         | 22 +++++++++++++++++++
 arch/riscv/boot/dts/starfive/jh7110.dtsi      |  9 ++++++++
 2 files changed, 31 insertions(+)
diff mbox series

Patch

diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
index 2a6d81609284..bbc2531999bc 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
@@ -126,6 +126,12 @@  &i2c6 {
 	status = "okay";
 };
 
+&ptc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm_pins>;
+	status = "okay";
+};
+
 &sysgpio {
 	i2c0_pins: i2c0-0 {
 		i2c-pins {
@@ -183,6 +189,22 @@  GPOEN_SYS_I2C6_DATA,
 		};
 	};
 
+	pwm_pins: pwm-0 {
+		pwm-pins {
+			pinmux = <GPIOMUX(46, GPOUT_SYS_PWM_CHANNEL0,
+					      GPOEN_SYS_PWM0_CHANNEL0,
+					      GPI_NONE)>,
+				 <GPIOMUX(59, GPOUT_SYS_PWM_CHANNEL1,
+					      GPOEN_SYS_PWM0_CHANNEL1,
+					      GPI_NONE)>;
+			bias-disable;
+			drive-strength = <12>;
+			input-disable;
+			input-schmitt-disable;
+			slew-rate = <0>;
+		};
+	};
+
 	uart0_pins: uart0-0 {
 		tx-pins {
 			pinmux = <GPIOMUX(5, GPOUT_SYS_UART0_TX,
diff --git a/arch/riscv/boot/dts/starfive/jh7110.dtsi b/arch/riscv/boot/dts/starfive/jh7110.dtsi
index 4c5fdb905da8..a82b81d07d88 100644
--- a/arch/riscv/boot/dts/starfive/jh7110.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110.dtsi
@@ -440,6 +440,15 @@  i2c6: i2c@12060000 {
 			status = "disabled";
 		};
 
+		ptc: pwm@120d0000 {
+			compatible = "starfive,jh7110-pwm";
+			reg = <0x0 0x120d0000 0x0 0x10000>;
+			clocks = <&syscrg JH7110_SYSCLK_PWM_APB>;
+			resets = <&syscrg JH7110_SYSRST_PWM_APB>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
+
 		syscrg: clock-controller@13020000 {
 			compatible = "starfive,jh7110-syscrg";
 			reg = <0x0 0x13020000 0x0 0x10000>;