[V4,4/6] arm64: dts: qcom: ipq9574: Add PCIe PHYs and controller nodes

Message ID 20230519090219.15925-5-quic_devipriy@quicinc.com
State New
Headers
Series Add PCIe support for IPQ9574 |

Commit Message

Devi Priya May 19, 2023, 9:02 a.m. UTC
  Add PCIe0, PCIe1, PCIe2, PCIe3 (and corresponding PHY) devices
found on IPQ9574 platform. The PCIe0 & PCIe1 are 1-lane Gen3
host whereas PCIe2 & PCIe3 are 2-lane Gen3 host.

Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
---
 Changes in V4:
	- No change

 arch/arm64/boot/dts/qcom/ipq9574.dtsi | 365 ++++++++++++++++++++++++++
 1 file changed, 365 insertions(+)
  

Patch

diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
index 16edffe53c8b..0e04549c69a5 100644
--- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
@@ -191,6 +191,58 @@ 
 			reg = <0x00060000 0x6000>;
 		};
 
+		pcie0_phy: phy@84000 {
+			compatible = "qcom,ipq9574-qmp-gen3x1-pcie-phy";
+			reg = <0x00084000 0x1000>;
+
+			clocks = <&gcc GCC_PCIE0_AUX_CLK>,
+				 <&gcc GCC_PCIE0_AHB_CLK>,
+				 <&gcc GCC_ANOC_PCIE0_1LANE_M_CLK>,
+				 <&gcc GCC_SNOC_PCIE0_1LANE_S_CLK>,
+				 <&gcc GCC_PCIE0_PIPE_CLK>;
+			clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane", "pipe";
+
+			assigned-clocks = <&gcc GCC_PCIE0_AUX_CLK>;
+			assigned-clock-rates = <20000000>;
+
+			resets = <&gcc GCC_PCIE0_PHY_BCR>,
+				 <&gcc GCC_PCIE0PHY_PHY_BCR>;
+			reset-names = "phy", "common";
+
+			#clock-cells = <0>;
+			clock-output-names = "gcc_pcie0_pipe_clk_src";
+
+			#phy-cells = <0>;
+			status = "disabled";
+
+		};
+
+		pcie2_phy: phy@8c000 {
+			compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy";
+			reg = <0x0008c000 0x2000>;
+
+			clocks = <&gcc GCC_PCIE2_AUX_CLK>,
+				 <&gcc GCC_PCIE2_AHB_CLK>,
+				 <&gcc GCC_ANOC_PCIE2_2LANE_M_CLK>,
+				 <&gcc GCC_SNOC_PCIE2_2LANE_S_CLK>,
+				 <&gcc GCC_PCIE2_PIPE_CLK>;
+			clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane", "pipe";
+
+			assigned-clocks = <&gcc GCC_PCIE2_AUX_CLK>;
+			assigned-clock-rates = <20000000>;
+
+			resets = <&gcc GCC_PCIE2_PHY_BCR>,
+				 <&gcc GCC_PCIE2PHY_PHY_BCR>;
+			reset-names = "phy", "common";
+
+			#clock-cells = <0>;
+			clock-output-names = "gcc_pcie2_pipe_clk_src";
+
+			#phy-cells = <0>;
+			status = "disabled";
+
+		};
+
 		rng: rng@e3000 {
 			compatible = "qcom,prng-ee";
 			reg = <0x000e3000 0x1000>;
@@ -198,6 +250,58 @@ 
 			clock-names = "core";
 		};
 
+		pcie3_phy: phy@f4000 {
+			compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy";
+			reg = <0x000f4000 0x2000>;
+
+			clocks = <&gcc GCC_PCIE3_AUX_CLK>,
+				 <&gcc GCC_PCIE3_AHB_CLK>,
+				 <&gcc GCC_ANOC_PCIE3_2LANE_M_CLK>,
+				 <&gcc GCC_SNOC_PCIE3_2LANE_S_CLK>,
+				 <&gcc GCC_PCIE3_PIPE_CLK>;
+			clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane", "pipe";
+
+			assigned-clocks = <&gcc GCC_PCIE3_AUX_CLK>;
+			assigned-clock-rates = <20000000>;
+
+			resets = <&gcc GCC_PCIE3_PHY_BCR>,
+				 <&gcc GCC_PCIE3PHY_PHY_BCR>;
+			reset-names = "phy", "common";
+
+			#clock-cells = <0>;
+			clock-output-names = "gcc_pcie3_pipe_clk_src";
+
+			#phy-cells = <0>;
+			status = "disabled";
+
+		};
+
+		pcie1_phy: phy@fc000 {
+			compatible = "qcom,ipq9574-qmp-gen3x1-pcie-phy";
+			reg = <0x000fc000 0x1000>;
+
+			clocks = <&gcc GCC_PCIE1_AUX_CLK>,
+				 <&gcc GCC_PCIE1_AHB_CLK>,
+				 <&gcc GCC_ANOC_PCIE1_1LANE_M_CLK>,
+				 <&gcc GCC_SNOC_PCIE1_1LANE_S_CLK>,
+				 <&gcc GCC_PCIE1_PIPE_CLK>;
+			clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane", "pipe";
+
+			assigned-clocks = <&gcc GCC_PCIE1_AUX_CLK>;
+			assigned-clock-rates = <20000000>;
+
+			resets = <&gcc GCC_PCIE1_PHY_BCR>,
+				 <&gcc GCC_PCIE1PHY_PHY_BCR>;
+			reset-names = "phy", "common";
+
+			#clock-cells = <0>;
+			clock-output-names = "gcc_pcie1_pipe_clk_src";
+
+			#phy-cells = <0>;
+			status = "disabled";
+
+		};
+
 		cryptobam: dma-controller@704000 {
 			compatible = "qcom,bam-v1.7.0";
 			reg = <0x00704000 0x20000>;
@@ -592,6 +696,267 @@ 
 				status = "disabled";
 			};
 		};
+
+		pcie1: pci@10000000 {
+			compatible = "qcom,pcie-ipq9574";
+			reg =  <0x10000000 0xf1d>,
+			       <0x10000F20 0xa8>,
+			       <0x10001000 0x1000>,
+			       <0x000F8000 0x4000>,
+			       <0x10100000 0x1000>;
+			reg-names = "dbi", "elbi", "atu", "parf", "config";
+			device_type = "pci";
+			linux,pci-domain = <2>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <1>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x01000000 0x0 0x00000000 0x10200000 0x0 0x100000>,  /* I/O */
+				 <0x02000000 0x0 0x10300000 0x10300000 0x0 0x7d00000>; /* MEM */
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 35 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 49 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 84 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 85 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global_irq";
+
+			/* clocks and clock-names are used to enable the clock in CBCR */
+			clocks = <&gcc GCC_PCIE1_AHB_CLK>,
+				 <&gcc GCC_PCIE1_AUX_CLK>,
+				 <&gcc GCC_PCIE1_AXI_M_CLK>,
+				 <&gcc GCC_PCIE1_AXI_S_CLK>,
+				 <&gcc GCC_PCIE1_AXI_S_BRIDGE_CLK>,
+				 <&gcc GCC_PCIE1_RCHNG_CLK>;
+			clock-names = "ahb",
+				      "aux",
+				      "axi_m",
+				      "axi_s",
+				      "axi_bridge",
+				      "rchng";
+
+			resets = <&gcc GCC_PCIE1_PIPE_ARES>,
+				 <&gcc GCC_PCIE1_CORE_STICKY_ARES>,
+				 <&gcc GCC_PCIE1_AXI_S_STICKY_ARES>,
+				 <&gcc GCC_PCIE1_AXI_S_ARES>,
+				 <&gcc GCC_PCIE1_AXI_M_STICKY_ARES>,
+				 <&gcc GCC_PCIE1_AXI_M_ARES>,
+				 <&gcc GCC_PCIE1_AUX_ARES>,
+				 <&gcc GCC_PCIE1_AHB_ARES>;
+			reset-names = "pipe",
+				      "sticky",
+				      "axi_s_sticky",
+				      "axi_s",
+				      "axi_m_sticky",
+				      "axi_m",
+				      "aux",
+				      "ahb";
+
+			phys = <&pcie1_phy>;
+			phy-names = "pciephy";
+			msi-parent = <&v2m0>;
+			status = "disabled";
+		};
+
+		pcie3: pci@18000000 {
+			compatible = "qcom,pcie-ipq9574";
+			reg =  <0x18000000 0xf1d>,
+			       <0x18000F20 0xa8>,
+			       <0x18001000 0x1000>,
+			       <0x000F0000 0x4000>,
+			       <0x18100000 0x1000>;
+			reg-names = "dbi", "elbi", "atu", "parf", "config";
+			device_type = "pci";
+			linux,pci-domain = <4>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <2>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x01000000 0x0 0x00000000 0x18200000 0x0 0x100000>,  /* I/O */
+				 <0x02000000 0x0 0x18300000 0x18300000 0x0 0x7d00000>; /* MEM */
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 189 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 190 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 191 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 192 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global_irq";
+
+			/* clocks and clock-names are used to enable the clock in CBCR */
+			clocks = <&gcc GCC_PCIE3_AHB_CLK>,
+				 <&gcc GCC_PCIE3_AUX_CLK>,
+				 <&gcc GCC_PCIE3_AXI_M_CLK>,
+				 <&gcc GCC_PCIE3_AXI_S_CLK>,
+				 <&gcc GCC_PCIE3_AXI_S_BRIDGE_CLK>,
+				 <&gcc GCC_PCIE3_RCHNG_CLK>;
+			clock-names = "ahb",
+				      "aux",
+				      "axi_m",
+				      "axi_s",
+				      "axi_bridge",
+				      "rchng";
+
+			resets = <&gcc GCC_PCIE3_PIPE_ARES>,
+				 <&gcc GCC_PCIE3_CORE_STICKY_ARES>,
+				 <&gcc GCC_PCIE3_AXI_S_STICKY_ARES>,
+				 <&gcc GCC_PCIE3_AXI_S_ARES>,
+				 <&gcc GCC_PCIE3_AXI_M_STICKY_ARES>,
+				 <&gcc GCC_PCIE3_AXI_M_ARES>,
+				 <&gcc GCC_PCIE3_AUX_ARES>,
+				 <&gcc GCC_PCIE3_AHB_ARES>;
+			reset-names = "pipe",
+				      "sticky",
+				      "axi_s_sticky",
+				      "axi_s",
+				      "axi_m_sticky",
+				      "axi_m",
+				      "aux",
+				      "ahb";
+
+			phys = <&pcie3_phy>;
+			phy-names = "pciephy";
+			msi-parent = <&v2m0>;
+			status = "disabled";
+		};
+
+		pcie2: pci@20000000 {
+			compatible = "qcom,pcie-ipq9574";
+			reg =  <0x20000000 0xf1d>,
+			       <0x20000F20 0xa8>,
+			       <0x20001000 0x1000>,
+			       <0x00088000 0x4000>,
+			       <0x20100000 0x1000>;
+			reg-names = "dbi", "elbi", "atu", "parf", "config";
+			device_type = "pci";
+			linux,pci-domain = <3>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <2>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x01000000 0x0 0x00000000 0x20200000 0x0 0x100000>,  /* I/O */
+				 <0x02000000 0x0 0x20300000 0x20300000 0x0 0x7d00000>; /* MEM */
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 164 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 165 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 186 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 187 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global_irq";
+
+			/* clocks and clock-names are used to enable the clock in CBCR */
+			clocks = <&gcc GCC_PCIE2_AHB_CLK>,
+				 <&gcc GCC_PCIE2_AUX_CLK>,
+				 <&gcc GCC_PCIE2_AXI_M_CLK>,
+				 <&gcc GCC_PCIE2_AXI_S_CLK>,
+				 <&gcc GCC_PCIE2_AXI_S_BRIDGE_CLK>,
+				 <&gcc GCC_PCIE2_RCHNG_CLK>;
+			clock-names = "ahb",
+				      "aux",
+				      "axi_m",
+				      "axi_s",
+				      "axi_bridge",
+				      "rchng";
+
+			resets = <&gcc GCC_PCIE2_PIPE_ARES>,
+				 <&gcc GCC_PCIE2_CORE_STICKY_ARES>,
+				 <&gcc GCC_PCIE2_AXI_S_STICKY_ARES>,
+				 <&gcc GCC_PCIE2_AXI_S_ARES>,
+				 <&gcc GCC_PCIE2_AXI_M_STICKY_ARES>,
+				 <&gcc GCC_PCIE2_AXI_M_ARES>,
+				 <&gcc GCC_PCIE2_AUX_ARES>,
+				 <&gcc GCC_PCIE2_AHB_ARES>;
+			reset-names = "pipe",
+				      "sticky",
+				      "axi_s_sticky",
+				      "axi_s",
+				      "axi_m_sticky",
+				      "axi_m",
+				      "aux",
+				      "ahb";
+
+			phys = <&pcie2_phy>;
+			phy-names = "pciephy";
+			msi-parent = <&v2m0>;
+			status = "disabled";
+		};
+
+		pcie0: pci@28000000 {
+			compatible = "qcom,pcie-ipq9574";
+			reg =  <0x28000000 0xf1d>,
+			       <0x28000F20 0xa8>,
+			       <0x28001000 0x1000>,
+			       <0x00080000 0x4000>,
+			       <0x28100000 0x1000>;
+			reg-names = "dbi", "elbi", "atu", "parf", "config";
+			device_type = "pci";
+			linux,pci-domain = <1>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <1>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x01000000 0x0 0x00000000 0x28200000 0x0 0x100000>,  /* I/O */
+				 <0x02000000 0x0 0x28300000 0x28300000 0x0 0x7d00000>; /* MEM */
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 75 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 78 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 79 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 83 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global_irq";
+
+			/* clocks and clock-names are used to enable the clock in CBCR */
+			clocks = <&gcc GCC_PCIE0_AHB_CLK>,
+				 <&gcc GCC_PCIE0_AUX_CLK>,
+				 <&gcc GCC_PCIE0_AXI_M_CLK>,
+				 <&gcc GCC_PCIE0_AXI_S_CLK>,
+				 <&gcc GCC_PCIE0_AXI_S_BRIDGE_CLK>,
+				 <&gcc GCC_PCIE0_RCHNG_CLK>;
+			clock-names = "ahb",
+				      "aux",
+				      "axi_m",
+				      "axi_s",
+				      "axi_bridge",
+				      "rchng";
+
+			resets = <&gcc GCC_PCIE0_PIPE_ARES>,
+				 <&gcc GCC_PCIE0_CORE_STICKY_ARES>,
+				 <&gcc GCC_PCIE0_AXI_S_STICKY_ARES>,
+				 <&gcc GCC_PCIE0_AXI_S_ARES>,
+				 <&gcc GCC_PCIE0_AXI_M_STICKY_ARES>,
+				 <&gcc GCC_PCIE0_AXI_M_ARES>,
+				 <&gcc GCC_PCIE0_AUX_ARES>,
+				 <&gcc GCC_PCIE0_AHB_ARES>;
+			reset-names = "pipe",
+				      "sticky",
+				      "axi_s_sticky",
+				      "axi_s",
+				      "axi_m_sticky",
+				      "axi_m",
+				      "aux",
+				      "ahb";
+
+			phys = <&pcie0_phy>;
+			phy-names = "pciephy";
+			msi-parent = <&v2m0>;
+			status = "disabled";
+		};
+
 	};
 
 	timer {