We must idle the uart only after serial8250_unregister_port(). Otherwise
unbinding the uart via sysfs while doing cat on the port produces an
imprecise external abort:
mem_serial_in from omap_8250_pm+0x44/0xf4
omap_8250_pm from uart_hangup+0xe0/0x194
uart_hangup from __tty_hangup.part.0+0x37c/0x3a8
__tty_hangup.part.0 from uart_remove_one_port+0x9c/0x22c
uart_remove_one_port from serial8250_unregister_port+0x60/0xe8
serial8250_unregister_port from omap8250_remove+0x6c/0xd0
omap8250_remove from platform_remove+0x28/0x54
Turns out the driver needs to have runtime PM functional before the
driver probe calls serial8250_register_8250_port(). And it needs
runtime PM after driver remove calls serial8250_unregister_port().
On probe, we need to read registers before registering the port in
omap_serial_fill_features_erratas(). We do that with custom uart_read()
already.
On remove, after serial8250_unregister_port(), we need to write to the
uart registers to idle the device. Let's add a custom uart_write() for
that.
Currently the uart register access depends on port->membase to be
initialized, which won't work after serial8250_unregister_port().
Let's use priv->membase instead, and use it for runtime PM related
functions to remove the dependency to port->membase for early and
late register access.
Note that during use, we need to check for a valid port in the runtime PM
related functions. This is needed for the optional wakeup configuration.
We now need to set the drvdata a bit earlier so it's available for the
runtime PM functions.
With the port checks in runtime PM functions, the old checks for priv in
omap8250_runtime_suspend() and omap8250_runtime_resume() functions are no
longer needed and are removed.
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
drivers/tty/serial/8250/8250_omap.c | 70 ++++++++++++++++-------------
1 file changed, 38 insertions(+), 32 deletions(-)
@@ -32,6 +32,7 @@
#include "8250.h"
#define DEFAULT_CLK_SPEED 48000000
+#define OMAP_UART_REGSHIFT 2
#define UART_ERRATA_i202_MDR1_ACCESS (1 << 0)
#define OMAP_UART_WER_HAS_TX_WAKEUP (1 << 1)
@@ -115,6 +116,7 @@
#define UART_OMAP_RX_LVL 0x19
struct omap8250_priv {
+ void __iomem *membase;
int line;
u8 habit;
u8 mdr1;
@@ -159,9 +161,14 @@ static void omap_8250_rx_dma_flush(struct uart_8250_port *p);
static inline void omap_8250_rx_dma_flush(struct uart_8250_port *p) { }
#endif
-static u32 uart_read(struct uart_8250_port *up, u32 reg)
+static u32 uart_read(struct omap8250_priv *priv, u32 reg)
{
- return readl(up->port.membase + (reg << up->port.regshift));
+ return readl(priv->membase + (reg << OMAP_UART_REGSHIFT));
+}
+
+static void uart_write(struct omap8250_priv *priv, u32 reg, u32 val)
+{
+ writel(val, priv->membase + (reg << OMAP_UART_REGSHIFT));
}
/*
@@ -548,7 +555,7 @@ static void omap_serial_fill_features_erratas(struct uart_8250_port *up,
u32 mvr, scheme;
u16 revision, major, minor;
- mvr = uart_read(up, UART_OMAP_MVER);
+ mvr = uart_read(priv, UART_OMAP_MVER);
/* Check revision register scheme */
scheme = mvr >> OMAP_UART_MVR_SCHEME_SHIFT;
@@ -1394,7 +1401,7 @@ static int omap8250_probe(struct platform_device *pdev)
UPF_HARD_FLOW;
up.port.private_data = priv;
- up.port.regshift = 2;
+ up.port.regshift = OMAP_UART_REGSHIFT;
up.port.fifosize = 64;
up.tx_loadsz = 64;
up.capabilities = UART_CAP_FIFO;
@@ -1457,6 +1464,8 @@ static int omap8250_probe(struct platform_device *pdev)
DEFAULT_CLK_SPEED);
}
+ priv->membase = membase;
+ priv->line = -ENODEV;
priv->latency = PM_QOS_CPU_LATENCY_DEFAULT_VALUE;
priv->calc_latency = PM_QOS_CPU_LATENCY_DEFAULT_VALUE;
cpu_latency_qos_add_request(&priv->pm_qos_request, priv->latency);
@@ -1464,6 +1473,8 @@ static int omap8250_probe(struct platform_device *pdev)
spin_lock_init(&priv->rx_dma_lock);
+ platform_set_drvdata(pdev, priv);
+
device_init_wakeup(&pdev->dev, true);
pm_runtime_enable(&pdev->dev);
pm_runtime_use_autosuspend(&pdev->dev);
@@ -1525,7 +1536,6 @@ static int omap8250_probe(struct platform_device *pdev)
goto err;
}
priv->line = ret;
- platform_set_drvdata(pdev, priv);
pm_runtime_mark_last_busy(&pdev->dev);
pm_runtime_put_autosuspend(&pdev->dev);
return 0;
@@ -1547,11 +1557,12 @@ static int omap8250_remove(struct platform_device *pdev)
if (err)
return err;
+ serial8250_unregister_port(priv->line);
+ priv->line = -ENODEV;
pm_runtime_dont_use_autosuspend(&pdev->dev);
pm_runtime_put_sync(&pdev->dev);
flush_work(&priv->qos_work);
pm_runtime_disable(&pdev->dev);
- serial8250_unregister_port(priv->line);
cpu_latency_qos_remove_request(&priv->pm_qos_request);
device_init_wakeup(&pdev->dev, false);
return 0;
@@ -1627,7 +1638,6 @@ static int omap8250_lost_context(struct uart_8250_port *up)
static int omap8250_soft_reset(struct device *dev)
{
struct omap8250_priv *priv = dev_get_drvdata(dev);
- struct uart_8250_port *up = serial8250_get_port(priv->line);
int timeout = 100;
int sysc;
int syss;
@@ -1641,20 +1651,20 @@ static int omap8250_soft_reset(struct device *dev)
* needing omap8250_soft_reset() quirk. Do it in two writes as
* recommended in the comment for omap8250_update_scr().
*/
- serial_out(up, UART_OMAP_SCR, OMAP_UART_SCR_DMAMODE_1);
- serial_out(up, UART_OMAP_SCR,
+ uart_write(priv, UART_OMAP_SCR, OMAP_UART_SCR_DMAMODE_1);
+ uart_write(priv, UART_OMAP_SCR,
OMAP_UART_SCR_DMAMODE_1 | OMAP_UART_SCR_DMAMODE_CTL);
- sysc = serial_in(up, UART_OMAP_SYSC);
+ sysc = uart_read(priv, UART_OMAP_SYSC);
/* softreset the UART */
sysc |= OMAP_UART_SYSC_SOFTRESET;
- serial_out(up, UART_OMAP_SYSC, sysc);
+ uart_write(priv, UART_OMAP_SYSC, sysc);
/* By experiments, 1us enough for reset complete on AM335x */
do {
udelay(1);
- syss = serial_in(up, UART_OMAP_SYSS);
+ syss = uart_read(priv, UART_OMAP_SYSS);
} while (--timeout && !(syss & OMAP_UART_SYSS_RESETDONE));
if (!timeout) {
@@ -1668,13 +1678,10 @@ static int omap8250_soft_reset(struct device *dev)
static int omap8250_runtime_suspend(struct device *dev)
{
struct omap8250_priv *priv = dev_get_drvdata(dev);
- struct uart_8250_port *up;
+ struct uart_8250_port *up = NULL;
- /* In case runtime-pm tries this before we are setup */
- if (!priv)
- return 0;
-
- up = serial8250_get_port(priv->line);
+ if (priv->line >= 0)
+ up = serial8250_get_port(priv->line);
/*
* When using 'no_console_suspend', the console UART must not be
* suspended. Since driver suspend is managed by runtime suspend,
@@ -1682,7 +1689,7 @@ static int omap8250_runtime_suspend(struct device *dev)
* active during suspend.
*/
if (priv->is_suspending && !console_suspend_enabled) {
- if (uart_console(&up->port))
+ if (up && uart_console(&up->port))
return -EBUSY;
}
@@ -1693,13 +1700,15 @@ static int omap8250_runtime_suspend(struct device *dev)
if (ret)
return ret;
- /* Restore to UART mode after reset (for wakeup) */
- omap8250_update_mdr1(up, priv);
- /* Restore wakeup enable register */
- serial_out(up, UART_OMAP_WER, priv->wer);
+ if (up) {
+ /* Restore to UART mode after reset (for wakeup) */
+ omap8250_update_mdr1(up, priv);
+ /* Restore wakeup enable register */
+ serial_out(up, UART_OMAP_WER, priv->wer);
+ }
}
- if (up->dma && up->dma->rxchan)
+ if (up && up->dma && up->dma->rxchan)
omap_8250_rx_dma_flush(up);
priv->latency = PM_QOS_CPU_LATENCY_DEFAULT_VALUE;
@@ -1711,18 +1720,15 @@ static int omap8250_runtime_suspend(struct device *dev)
static int omap8250_runtime_resume(struct device *dev)
{
struct omap8250_priv *priv = dev_get_drvdata(dev);
- struct uart_8250_port *up;
+ struct uart_8250_port *up = NULL;
- /* In case runtime-pm tries this before we are setup */
- if (!priv)
- return 0;
+ if (priv->line >= 0)
+ up = serial8250_get_port(priv->line);
- up = serial8250_get_port(priv->line);
-
- if (omap8250_lost_context(up))
+ if (up && omap8250_lost_context(up))
omap8250_restore_regs(up);
- if (up->dma && up->dma->rxchan && !(priv->habit & UART_HAS_EFR2))
+ if (up && up->dma && up->dma->rxchan && !(priv->habit & UART_HAS_EFR2))
omap_8250_rx_dma(up);
priv->latency = priv->calc_latency;