[5/6] ARM: dts: msm8226: Add tsens node and related nvmem cells
Commit Message
Specify pre-parsed per-sensor calibration nvmem cells in the qfprom
device node rather than parsing the whole data blob in the driver.
Signed-off-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
---
arch/arm/boot/dts/qcom-msm8226.dtsi | 113 ++++++++++++++++++++++++++++
1 file changed, 113 insertions(+)
Comments
On 07/05/2023 23:12, Matti Lehtimäki wrote:
> Specify pre-parsed per-sensor calibration nvmem cells in the qfprom
> device node rather than parsing the whole data blob in the driver.
>
> Signed-off-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
> ---
> arch/arm/boot/dts/qcom-msm8226.dtsi | 113 ++++++++++++++++++++++++++++
> 1 file changed, 113 insertions(+)
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
I did not manually check all the offsets, but they look sane to me.
@@ -500,6 +500,34 @@ data-pins {
};
};
+ tsens: thermal-sensor@fc4a9000 {
+ compatible = "qcom,msm8226-tsens", "qcom,tsens-v0_1";
+ reg = <0xfc4a9000 0x1000>, /* TM */
+ <0xfc4a8000 0x1000>; /* SROT */
+ nvmem-cells = <&tsens_mode>,
+ <&tsens_base1>, <&tsens_base2>,
+ <&tsens_s0_p1>, <&tsens_s0_p2>,
+ <&tsens_s1_p1>, <&tsens_s1_p2>,
+ <&tsens_s2_p1>, <&tsens_s2_p2>,
+ <&tsens_s3_p1>, <&tsens_s3_p2>,
+ <&tsens_s4_p1>, <&tsens_s4_p2>,
+ <&tsens_s5_p1>, <&tsens_s5_p2>,
+ <&tsens_s6_p1>, <&tsens_s6_p2>;
+ nvmem-cell-names = "mode",
+ "base1", "base2",
+ "s0_p1", "s0_p2",
+ "s1_p1", "s1_p2",
+ "s2_p1", "s2_p2",
+ "s3_p1", "s3_p2",
+ "s4_p1", "s4_p2",
+ "s5_p1", "s5_p2",
+ "s6_p1", "s6_p2";
+ #qcom,sensors = <6>;
+ interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "uplow";
+ #thermal-sensor-cells = <1>;
+ };
+
restart@fc4ab000 {
compatible = "qcom,pshold";
reg = <0xfc4ab000 0x4>;
@@ -510,6 +538,91 @@ qfprom: qfprom@fc4bc000 {
reg = <0xfc4bc000 0x1000>;
#address-cells = <1>;
#size-cells = <1>;
+
+ tsens_base1: base1@1c1 {
+ reg = <0x1c1 0x2>;
+ bits = <5 8>;
+ };
+
+ tsens_s0_p1: s0-p1@1c2 {
+ reg = <0x1c2 0x2>;
+ bits = <5 6>;
+ };
+
+ tsens_s1_p1: s1-p1@1c4 {
+ reg = <0x1c4 0x1>;
+ bits = <0 6>;
+ };
+
+ tsens_s2_p1: s2-p1@1c4 {
+ reg = <0x1c4 0x2>;
+ bits = <6 6>;
+ };
+
+ tsens_s3_p1: s3-p1@1c5 {
+ reg = <0x1c5 0x2>;
+ bits = <4 6>;
+ };
+
+ tsens_s4_p1: s4-p1@1c6 {
+ reg = <0x1c6 0x1>;
+ bits = <2 6>;
+ };
+
+ tsens_s5_p1: s5-p1@1c7 {
+ reg = <0x1c7 0x1>;
+ bits = <0 6>;
+ };
+
+ tsens_s6_p1: s6-p1@1ca {
+ reg = <0x1ca 0x2>;
+ bits = <4 6>;
+ };
+
+ tsens_base2: base2@1cc {
+ reg = <0x1cc 0x1>;
+ bits = <0 8>;
+ };
+
+ tsens_s0_p2: s0-p2@1cd {
+ reg = <0x1cd 0x1>;
+ bits = <0 6>;
+ };
+
+ tsens_s1_p2: s1-p2@1cd {
+ reg = <0x1cd 0x2>;
+ bits = <6 6>;
+ };
+
+ tsens_s2_p2: s2-p2@1ce {
+ reg = <0x1ce 0x2>;
+ bits = <4 6>;
+ };
+
+ tsens_s3_p2: s3-p2@1cf {
+ reg = <0x1cf 0x1>;
+ bits = <2 6>;
+ };
+
+ tsens_s4_p2: s4-p2@446 {
+ reg = <0x446 0x2>;
+ bits = <4 6>;
+ };
+
+ tsens_s5_p2: s5-p2@447 {
+ reg = <0x447 0x1>;
+ bits = <2 6>;
+ };
+
+ tsens_s6_p2: s6-p2@44e {
+ reg = <0x44e 0x1>;
+ bits = <1 6>;
+ };
+
+ tsens_mode: mode@44f {
+ reg = <0x44f 0x1>;
+ bits = <5 3>;
+ };
};
spmi_bus: spmi@fc4cf000 {