[3/3] spi: spi-imx: fix use of more than four chipselects
Commit Message
Currently, the spi->chip_select is used unconditionally in code such as
/* set chip select to use */
ctrl |= MX51_ECSPI_CTRL_CS(spi->chip_select);
and
if (spi->mode & SPI_CPHA)
cfg |= MX51_ECSPI_CONFIG_SCLKPHA(spi->chip_select);
else
cfg &= ~MX51_ECSPI_CONFIG_SCLKPHA(spi->chip_select);
with these macros being
#define MX51_ECSPI_CTRL_CS(cs) ((cs) << 18)
#define MX51_ECSPI_CONFIG_SCLKPHA(cs) (1 << ((cs) + 0))
However, the CHANNEL_SELECT field in the control register is only two
bits wide, so when spi->chip_select >= 4, we end up writing garbage
into the BURST_LENGTH field. Similarly, there are only four bits in
the SCLK_PHA field, so the code above ends up actually modifying bits
in the SCLK_POL (or higher) field.
The scrambling of the BURST_LENGTH field itself is probably benign,
since that is explicitly completely initialized later, in
->prepare_transfer.
But, since we effectively write (spi->chip_select & 3) into the
CHANNEL_SELECT field, that value is what the IP block then uses to
determine which bits of the configuration register control phase,
polarity etc., and those bits are not properly initialized, so
communication with the spi device completely fails.
Fix this by using the ->unused_native_cs value as channel number for
any spi device which uses a gpio as chip select.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
drivers/spi/spi-imx.c | 31 ++++++++++++++++++++-----------
1 file changed, 20 insertions(+), 11 deletions(-)
Comments
Hello,
> -----Original Message-----
> From: Rasmus Villemoes <linux@rasmusvillemoes.dk>
> Sent: Tuesday, April 25, 2023 7:15 PM
> To: Mark Brown <broonie@kernel.org>; Shawn Guo <shawnguo@kernel.org>;
> Sascha Hauer <s.hauer@pengutronix.de>; Pengutronix Kernel Team
> <kernel@pengutronix.de>; Fabio Estevam <festevam@gmail.com>; NXP Linux
> Team <linux-imx@nxp.com>
> Cc: Marc Kleine-Budde <mkl@pengutronix.de>; Rasmus Villemoes
> <linux@rasmusvillemoes.dk>; linux-spi@vger.kernel.org; linux-arm-
> kernel@lists.infradead.org; linux-kernel@vger.kernel.org
> Subject: [PATCH 3/3] spi: spi-imx: fix use of more than four chipselects
>
> CAUTION: This message has originated from an External Source. Please use
> proper judgment and caution when opening attachments, clicking links, or
> responding to this email.
>
>
> Currently, the spi->chip_select is used unconditionally in code such as
>
> /* set chip select to use */
> ctrl |= MX51_ECSPI_CTRL_CS(spi->chip_select);
>
> and
>
> if (spi->mode & SPI_CPHA)
> cfg |= MX51_ECSPI_CONFIG_SCLKPHA(spi->chip_select);
> else
> cfg &= ~MX51_ECSPI_CONFIG_SCLKPHA(spi->chip_select);
>
> with these macros being
>
> #define MX51_ECSPI_CTRL_CS(cs) ((cs) << 18)
> #define MX51_ECSPI_CONFIG_SCLKPHA(cs) (1 << ((cs) + 0))
>
> However, the CHANNEL_SELECT field in the control register is only two bits
> wide, so when spi->chip_select >= 4, we end up writing garbage into the
> BURST_LENGTH field. Similarly, there are only four bits in the SCLK_PHA field,
> so the code above ends up actually modifying bits in the SCLK_POL (or higher)
> field.
>
> The scrambling of the BURST_LENGTH field itself is probably benign, since
> that is explicitly completely initialized later, in
> ->prepare_transfer.
>
> But, since we effectively write (spi->chip_select & 3) into the
> CHANNEL_SELECT field, that value is what the IP block then uses to determine
> which bits of the configuration register control phase, polarity etc., and those
> bits are not properly initialized, so communication with the spi device
> completely fails.
>
> Fix this by using the ->unused_native_cs value as channel number for any spi
> device which uses a gpio as chip select.
>
> Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
> ---
> drivers/spi/spi-imx.c | 31 ++++++++++++++++++++-----------
> 1 file changed, 20 insertions(+), 11 deletions(-)
>
> diff --git a/drivers/spi/spi-imx.c b/drivers/spi/spi-imx.c index
> e8f7afbd9847..569a5132f324 100644
> --- a/drivers/spi/spi-imx.c
> +++ b/drivers/spi/spi-imx.c
> @@ -504,6 +504,13 @@ static void mx51_ecspi_disable(struct spi_imx_data
> *spi_imx)
> writel(ctrl, spi_imx->base + MX51_ECSPI_CTRL); }
>
> +static int mx51_ecspi_channel(const struct spi_device *spi) {
> + if (!spi->cs_gpiod)
> + return spi->chip_select;
New set/get APIs for accessing spi->chip_select and spi->cs_gpiod were introduced by
https://github.com/torvalds/linux/commit/303feb3cc06ac0665d0ee9c1414941200e60e8a3
please use these APIs instead of accessing spi->chip_select & spi->cs_gpiod directly.
Regards,
Amit
> + return spi->controller->unused_native_cs;
> +}
> +
> static int mx51_ecspi_prepare_message(struct spi_imx_data *spi_imx,
> struct spi_message *msg) { @@ -514,6 +521,7 @@
> static int mx51_ecspi_prepare_message(struct spi_imx_data *spi_imx,
> u32 testreg, delay;
> u32 cfg = readl(spi_imx->base + MX51_ECSPI_CONFIG);
> u32 current_cfg = cfg;
> + int channel = mx51_ecspi_channel(spi);
>
> /* set Master or Slave mode */
> if (spi_imx->slave_mode)
> @@ -528,7 +536,7 @@ static int mx51_ecspi_prepare_message(struct
> spi_imx_data *spi_imx,
> ctrl |= MX51_ECSPI_CTRL_DRCTL(spi_imx->spi_drctl);
>
> /* set chip select to use */
> - ctrl |= MX51_ECSPI_CTRL_CS(spi->chip_select);
> + ctrl |= MX51_ECSPI_CTRL_CS(channel);
>
> /*
> * The ctrl register must be written first, with the EN bit set other @@ -
> 549,22 +557,22 @@ static int mx51_ecspi_prepare_message(struct
> spi_imx_data *spi_imx,
> * BURST_LENGTH + 1 bits are received
> */
> if (spi_imx->slave_mode && is_imx53_ecspi(spi_imx))
> - cfg &= ~MX51_ECSPI_CONFIG_SBBCTRL(spi->chip_select);
> + cfg &= ~MX51_ECSPI_CONFIG_SBBCTRL(channel);
> else
> - cfg |= MX51_ECSPI_CONFIG_SBBCTRL(spi->chip_select);
> + cfg |= MX51_ECSPI_CONFIG_SBBCTRL(channel);
>
> if (spi->mode & SPI_CPOL) {
> - cfg |= MX51_ECSPI_CONFIG_SCLKPOL(spi->chip_select);
> - cfg |= MX51_ECSPI_CONFIG_SCLKCTL(spi->chip_select);
> + cfg |= MX51_ECSPI_CONFIG_SCLKPOL(channel);
> + cfg |= MX51_ECSPI_CONFIG_SCLKCTL(channel);
> } else {
> - cfg &= ~MX51_ECSPI_CONFIG_SCLKPOL(spi->chip_select);
> - cfg &= ~MX51_ECSPI_CONFIG_SCLKCTL(spi->chip_select);
> + cfg &= ~MX51_ECSPI_CONFIG_SCLKPOL(channel);
> + cfg &= ~MX51_ECSPI_CONFIG_SCLKCTL(channel);
> }
>
> if (spi->mode & SPI_CS_HIGH)
> - cfg |= MX51_ECSPI_CONFIG_SSBPOL(spi->chip_select);
> + cfg |= MX51_ECSPI_CONFIG_SSBPOL(channel);
> else
> - cfg &= ~MX51_ECSPI_CONFIG_SSBPOL(spi->chip_select);
> + cfg &= ~MX51_ECSPI_CONFIG_SSBPOL(channel);
>
> if (cfg == current_cfg)
> return 0;
> @@ -609,14 +617,15 @@ static void mx51_configure_cpha(struct
> spi_imx_data *spi_imx,
> bool cpha = (spi->mode & SPI_CPHA);
> bool flip_cpha = (spi->mode & SPI_RX_CPHA_FLIP) && spi_imx->rx_only;
> u32 cfg = readl(spi_imx->base + MX51_ECSPI_CONFIG);
> + int channel = mx51_ecspi_channel(spi);
>
> /* Flip cpha logical value iff flip_cpha */
> cpha ^= flip_cpha;
>
> if (cpha)
> - cfg |= MX51_ECSPI_CONFIG_SCLKPHA(spi->chip_select);
> + cfg |= MX51_ECSPI_CONFIG_SCLKPHA(channel);
> else
> - cfg &= ~MX51_ECSPI_CONFIG_SCLKPHA(spi->chip_select);
> + cfg &= ~MX51_ECSPI_CONFIG_SCLKPHA(channel);
>
> writel(cfg, spi_imx->base + MX51_ECSPI_CONFIG); }
> --
> 2.37.2
@@ -504,6 +504,13 @@ static void mx51_ecspi_disable(struct spi_imx_data *spi_imx)
writel(ctrl, spi_imx->base + MX51_ECSPI_CTRL);
}
+static int mx51_ecspi_channel(const struct spi_device *spi)
+{
+ if (!spi->cs_gpiod)
+ return spi->chip_select;
+ return spi->controller->unused_native_cs;
+}
+
static int mx51_ecspi_prepare_message(struct spi_imx_data *spi_imx,
struct spi_message *msg)
{
@@ -514,6 +521,7 @@ static int mx51_ecspi_prepare_message(struct spi_imx_data *spi_imx,
u32 testreg, delay;
u32 cfg = readl(spi_imx->base + MX51_ECSPI_CONFIG);
u32 current_cfg = cfg;
+ int channel = mx51_ecspi_channel(spi);
/* set Master or Slave mode */
if (spi_imx->slave_mode)
@@ -528,7 +536,7 @@ static int mx51_ecspi_prepare_message(struct spi_imx_data *spi_imx,
ctrl |= MX51_ECSPI_CTRL_DRCTL(spi_imx->spi_drctl);
/* set chip select to use */
- ctrl |= MX51_ECSPI_CTRL_CS(spi->chip_select);
+ ctrl |= MX51_ECSPI_CTRL_CS(channel);
/*
* The ctrl register must be written first, with the EN bit set other
@@ -549,22 +557,22 @@ static int mx51_ecspi_prepare_message(struct spi_imx_data *spi_imx,
* BURST_LENGTH + 1 bits are received
*/
if (spi_imx->slave_mode && is_imx53_ecspi(spi_imx))
- cfg &= ~MX51_ECSPI_CONFIG_SBBCTRL(spi->chip_select);
+ cfg &= ~MX51_ECSPI_CONFIG_SBBCTRL(channel);
else
- cfg |= MX51_ECSPI_CONFIG_SBBCTRL(spi->chip_select);
+ cfg |= MX51_ECSPI_CONFIG_SBBCTRL(channel);
if (spi->mode & SPI_CPOL) {
- cfg |= MX51_ECSPI_CONFIG_SCLKPOL(spi->chip_select);
- cfg |= MX51_ECSPI_CONFIG_SCLKCTL(spi->chip_select);
+ cfg |= MX51_ECSPI_CONFIG_SCLKPOL(channel);
+ cfg |= MX51_ECSPI_CONFIG_SCLKCTL(channel);
} else {
- cfg &= ~MX51_ECSPI_CONFIG_SCLKPOL(spi->chip_select);
- cfg &= ~MX51_ECSPI_CONFIG_SCLKCTL(spi->chip_select);
+ cfg &= ~MX51_ECSPI_CONFIG_SCLKPOL(channel);
+ cfg &= ~MX51_ECSPI_CONFIG_SCLKCTL(channel);
}
if (spi->mode & SPI_CS_HIGH)
- cfg |= MX51_ECSPI_CONFIG_SSBPOL(spi->chip_select);
+ cfg |= MX51_ECSPI_CONFIG_SSBPOL(channel);
else
- cfg &= ~MX51_ECSPI_CONFIG_SSBPOL(spi->chip_select);
+ cfg &= ~MX51_ECSPI_CONFIG_SSBPOL(channel);
if (cfg == current_cfg)
return 0;
@@ -609,14 +617,15 @@ static void mx51_configure_cpha(struct spi_imx_data *spi_imx,
bool cpha = (spi->mode & SPI_CPHA);
bool flip_cpha = (spi->mode & SPI_RX_CPHA_FLIP) && spi_imx->rx_only;
u32 cfg = readl(spi_imx->base + MX51_ECSPI_CONFIG);
+ int channel = mx51_ecspi_channel(spi);
/* Flip cpha logical value iff flip_cpha */
cpha ^= flip_cpha;
if (cpha)
- cfg |= MX51_ECSPI_CONFIG_SCLKPHA(spi->chip_select);
+ cfg |= MX51_ECSPI_CONFIG_SCLKPHA(channel);
else
- cfg &= ~MX51_ECSPI_CONFIG_SCLKPHA(spi->chip_select);
+ cfg &= ~MX51_ECSPI_CONFIG_SCLKPHA(channel);
writel(cfg, spi_imx->base + MX51_ECSPI_CONFIG);
}