[1/2] arm64: dts: ti: k3-j7200: Fix physical address of pin

Message ID 20230414181434.2046049-2-u-kumar1@ti.com
State New
Headers
Series arm64: dts: ti: k3-j7200-common-proc-board fixes |

Commit Message

Kumar, Udit April 14, 2023, 6:14 p.m. UTC
  Fixes: 9ae21ac445e9 ("arm64: dts: ti: k3-j7200: Fix wakeup pinmux range")

wkup_pmx splits into multiple regions. Like

    wkup_pmx0 -> 13 pins (WKUP_PADCONFIG 0 - 12)
    wkup_pmx1 -> 2 pins (WKUP_PADCONFIG 14 - 15)
    wkup_pmx2 -> 59 pins (WKUP_PADCONFIG 26 - 84)
    wkup_pmx3 -> 8 pins (WKUP_PADCONFIG 93 - 100)

With this split, pin offset needs to be adjusted to
match with new pmx for all pins above wkup_pmx0.

Example a pin under wkup_pmx1 should start from 0 instead of
old offset(0x38 WKUP_PADCONFIG 14 offset)

J7200 Datasheet (Table 6-106, Section 6.4 Pin Multiplexing) :
            https://www.ti.com/lit/ds/symlink/dra821u.pdf

Signed-off-by: J Keerthi <j-keerthy@ti.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
---
 .../dts/ti/k3-j7200-common-proc-board.dts     | 28 +++++++++----------
 1 file changed, 14 insertions(+), 14 deletions(-)
  

Comments

Nishanth Menon April 14, 2023, 6:26 p.m. UTC | #1
On 23:44-20230414, Udit Kumar wrote:
> Fixes: 9ae21ac445e9 ("arm64: dts: ti: k3-j7200: Fix wakeup pinmux range")

In the wrong place.
> 
> wkup_pmx splits into multiple regions. Like
> 
>     wkup_pmx0 -> 13 pins (WKUP_PADCONFIG 0 - 12)
>     wkup_pmx1 -> 2 pins (WKUP_PADCONFIG 14 - 15)
>     wkup_pmx2 -> 59 pins (WKUP_PADCONFIG 26 - 84)
>     wkup_pmx3 -> 8 pins (WKUP_PADCONFIG 93 - 100)
> 
> With this split, pin offset needs to be adjusted to
> match with new pmx for all pins above wkup_pmx0.
> 
> Example a pin under wkup_pmx1 should start from 0 instead of
> old offset(0x38 WKUP_PADCONFIG 14 offset)
> 
> J7200 Datasheet (Table 6-106, Section 6.4 Pin Multiplexing) :
>             https://www.ti.com/lit/ds/symlink/dra821u.pdf

Drop the preceding whitespace.

> 
> Signed-off-by: J Keerthi <j-keerthy@ti.com>

Spell check name please, I think he usually goes with:

Signed-off-by: Keerthy <j-keerthy@ti.com>

If this patch is from Keerthy, the patch should have a "From:"

> Signed-off-by: Udit Kumar <u-kumar1@ti.com>
> ---
>  .../dts/ti/k3-j7200-common-proc-board.dts     | 28 +++++++++----------
>  1 file changed, 14 insertions(+), 14 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> index 0d39d6b8cc0c..63633e4f6c59 100644
> --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> @@ -83,25 +83,25 @@ vdd_sd_dv: gpio-regulator-TLV71033 {
>  &wkup_pmx2 {
>  	mcu_cpsw_pins_default: mcu-cpsw-pins-default {
>  		pinctrl-single,pins = <
> -			J721E_WKUP_IOPAD(0x0068, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
> -			J721E_WKUP_IOPAD(0x006c, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
> -			J721E_WKUP_IOPAD(0x0070, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */
> -			J721E_WKUP_IOPAD(0x0074, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */
> -			J721E_WKUP_IOPAD(0x0078, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */
> -			J721E_WKUP_IOPAD(0x007c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */
> -			J721E_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
> -			J721E_WKUP_IOPAD(0x008c, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
> -			J721E_WKUP_IOPAD(0x0090, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
> -			J721E_WKUP_IOPAD(0x0094, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
> -			J721E_WKUP_IOPAD(0x0080, PIN_OUTPUT, 0) /* MCU_RGMII1_TXC */
> -			J721E_WKUP_IOPAD(0x0084, PIN_INPUT, 0) /* MCU_RGMII1_RXC */
> +			J721E_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
> +			J721E_WKUP_IOPAD(0x0004, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
> +			J721E_WKUP_IOPAD(0x0008, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */
> +			J721E_WKUP_IOPAD(0x000c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */
> +			J721E_WKUP_IOPAD(0x0010, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */
> +			J721E_WKUP_IOPAD(0x0014, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */
> +			J721E_WKUP_IOPAD(0x0020, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
> +			J721E_WKUP_IOPAD(0x0024, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
> +			J721E_WKUP_IOPAD(0x0028, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
> +			J721E_WKUP_IOPAD(0x002c, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
> +			J721E_WKUP_IOPAD(0x0018, PIN_OUTPUT, 0) /* MCU_RGMII1_TXC */
> +			J721E_WKUP_IOPAD(0x001c, PIN_INPUT, 0) /* MCU_RGMII1_RXC */

nice catch.

>  		>;
>  	};
>  
>  	mcu_mdio_pins_default: mcu-mdio1-pins-default {
>  		pinctrl-single,pins = <
> -			J721E_WKUP_IOPAD(0x009c, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
> -			J721E_WKUP_IOPAD(0x0098, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
> +			J721E_WKUP_IOPAD(0x0034, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
> +			J721E_WKUP_IOPAD(0x0030, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
>  		>;
>  	};
>  };
> -- 
> 2.34.1
>
  
Kumar, Udit April 15, 2023, 4:10 a.m. UTC | #2
Hi Nishanth

On 4/14/2023 11:56 PM, Nishanth Menon wrote:
> On 23:44-20230414, Udit Kumar wrote:
>> Fixes: 9ae21ac445e9 ("arm64: dts: ti: k3-j7200: Fix wakeup pinmux range")
> In the wrong place.


will address in v2


>> wkup_pmx splits into multiple regions. Like
>>
>>      wkup_pmx0 -> 13 pins (WKUP_PADCONFIG 0 - 12)
>>      wkup_pmx1 -> 2 pins (WKUP_PADCONFIG 14 - 15)
>>      wkup_pmx2 -> 59 pins (WKUP_PADCONFIG 26 - 84)
>>      wkup_pmx3 -> 8 pins (WKUP_PADCONFIG 93 - 100)
>>
>> With this split, pin offset needs to be adjusted to
>> match with new pmx for all pins above wkup_pmx0.
>>
>> Example a pin under wkup_pmx1 should start from 0 instead of
>> old offset(0x38 WKUP_PADCONFIG 14 offset)
>>
>> J7200 Datasheet (Table 6-106, Section 6.4 Pin Multiplexing) :
>>              https://www.ti.com/lit/ds/symlink/dra821u.pdf
> Drop the preceding whitespace.

ok

>> Signed-off-by: J Keerthi <j-keerthy@ti.com>
> Spell check name please, I think he usually goes with:
>
> Signed-off-by: Keerthy <j-keerthy@ti.com>
>
> If this patch is from Keerthy, the patch should have a "From:"

ok.

git apply on original patch didn't worked , so i applied and committed.

will fix in patch itself before posting, Keerthi as author


>> Signed-off-by: Udit Kumar <u-kumar1@ti.com>
>> ---
>>   .../dts/ti/k3-j7200-common-proc-board.dts     | 28 +++++++++----------
>>   1 file changed, 14 insertions(+), 14 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
>> index 0d39d6b8cc0c..63633e4f6c59 100644
>> --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
>> +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
>> @@ -83,25 +83,25 @@ vdd_sd_dv: gpio-regulator-TLV71033 {
>>   &wkup_pmx2 {
>>   	mcu_cpsw_pins_default: mcu-cpsw-pins-default {
>>   		pinctrl-single,pins = <
>> -			J721E_WKUP_IOPAD(0x0068, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
>> -			J721E_WKUP_IOPAD(0x006c, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
>> -			J721E_WKUP_IOPAD(0x0070, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */
>> -			J721E_WKUP_IOPAD(0x0074, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */
>> -			J721E_WKUP_IOPAD(0x0078, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */
>> -			J721E_WKUP_IOPAD(0x007c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */
>> -			J721E_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
>> -			J721E_WKUP_IOPAD(0x008c, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
>> -			J721E_WKUP_IOPAD(0x0090, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
>> -			J721E_WKUP_IOPAD(0x0094, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
>> -			J721E_WKUP_IOPAD(0x0080, PIN_OUTPUT, 0) /* MCU_RGMII1_TXC */
>> -			J721E_WKUP_IOPAD(0x0084, PIN_INPUT, 0) /* MCU_RGMII1_RXC */
>> +			J721E_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
>> +			J721E_WKUP_IOPAD(0x0004, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
>> +			J721E_WKUP_IOPAD(0x0008, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */
>> +			J721E_WKUP_IOPAD(0x000c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */
>> +			J721E_WKUP_IOPAD(0x0010, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */
>> +			J721E_WKUP_IOPAD(0x0014, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */
>> +			J721E_WKUP_IOPAD(0x0020, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
>> +			J721E_WKUP_IOPAD(0x0024, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
>> +			J721E_WKUP_IOPAD(0x0028, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
>> +			J721E_WKUP_IOPAD(0x002c, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
>> +			J721E_WKUP_IOPAD(0x0018, PIN_OUTPUT, 0) /* MCU_RGMII1_TXC */
>> +			J721E_WKUP_IOPAD(0x001c, PIN_INPUT, 0) /* MCU_RGMII1_RXC */
> nice catch.
>
>>   		>;
>>   	};
>>   
>>   	mcu_mdio_pins_default: mcu-mdio1-pins-default {
>>   		pinctrl-single,pins = <
>> -			J721E_WKUP_IOPAD(0x009c, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
>> -			J721E_WKUP_IOPAD(0x0098, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
>> +			J721E_WKUP_IOPAD(0x0034, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
>> +			J721E_WKUP_IOPAD(0x0030, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
>>   		>;
>>   	};
>>   };
>> -- 
>> 2.34.1
>>
  
Nishanth Menon April 15, 2023, 12:47 p.m. UTC | #3
On 09:40-20230415, Kumar, Udit wrote:
[...]
> git apply on original patch didn't worked , so i applied and committed.
> 
> will fix in patch itself before posting, Keerthi as author
Yes, with s/Keerthi/Keerthy please.
  

Patch

diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index 0d39d6b8cc0c..63633e4f6c59 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -83,25 +83,25 @@  vdd_sd_dv: gpio-regulator-TLV71033 {
 &wkup_pmx2 {
 	mcu_cpsw_pins_default: mcu-cpsw-pins-default {
 		pinctrl-single,pins = <
-			J721E_WKUP_IOPAD(0x0068, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
-			J721E_WKUP_IOPAD(0x006c, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
-			J721E_WKUP_IOPAD(0x0070, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */
-			J721E_WKUP_IOPAD(0x0074, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */
-			J721E_WKUP_IOPAD(0x0078, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */
-			J721E_WKUP_IOPAD(0x007c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */
-			J721E_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
-			J721E_WKUP_IOPAD(0x008c, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
-			J721E_WKUP_IOPAD(0x0090, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
-			J721E_WKUP_IOPAD(0x0094, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
-			J721E_WKUP_IOPAD(0x0080, PIN_OUTPUT, 0) /* MCU_RGMII1_TXC */
-			J721E_WKUP_IOPAD(0x0084, PIN_INPUT, 0) /* MCU_RGMII1_RXC */
+			J721E_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
+			J721E_WKUP_IOPAD(0x0004, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
+			J721E_WKUP_IOPAD(0x0008, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */
+			J721E_WKUP_IOPAD(0x000c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */
+			J721E_WKUP_IOPAD(0x0010, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */
+			J721E_WKUP_IOPAD(0x0014, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */
+			J721E_WKUP_IOPAD(0x0020, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
+			J721E_WKUP_IOPAD(0x0024, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
+			J721E_WKUP_IOPAD(0x0028, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
+			J721E_WKUP_IOPAD(0x002c, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
+			J721E_WKUP_IOPAD(0x0018, PIN_OUTPUT, 0) /* MCU_RGMII1_TXC */
+			J721E_WKUP_IOPAD(0x001c, PIN_INPUT, 0) /* MCU_RGMII1_RXC */
 		>;
 	};
 
 	mcu_mdio_pins_default: mcu-mdio1-pins-default {
 		pinctrl-single,pins = <
-			J721E_WKUP_IOPAD(0x009c, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
-			J721E_WKUP_IOPAD(0x0098, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
+			J721E_WKUP_IOPAD(0x0034, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
+			J721E_WKUP_IOPAD(0x0030, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
 		>;
 	};
 };