[v4,4/7] phy: starfive: add JH7110 PCIE 2.0 PHY driver.

Message ID 20230406015216.27034-5-minda.chen@starfivetech.com
State New
Headers
Series Add JH7110 USB and USB PHY driver support |

Commit Message

Minda Chen April 6, 2023, 1:52 a.m. UTC
  Add Starfive JH7110 SoC PCIe 2.0 driver support.
PCIe 2.0 PHY default connect to PCIe controller.
But pcie0 PHY can connect to USB 3.0 controlller.

Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
---
 MAINTAINERS                            |   4 +-
 drivers/phy/starfive/Kconfig           |  11 ++
 drivers/phy/starfive/Makefile          |   1 +
 drivers/phy/starfive/phy-jh7110-pcie.c | 197 +++++++++++++++++++++++++
 4 files changed, 212 insertions(+), 1 deletion(-)
 create mode 100644 drivers/phy/starfive/phy-jh7110-pcie.c
  

Patch

diff --git a/MAINTAINERS b/MAINTAINERS
index 9da352084403..d98b70d62fd4 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -19968,11 +19968,13 @@  M:	William Qiu <william.qiu@starfivetech.com>
 S:	Supported
 F:	Documentation/devicetree/bindings/soc/starfive/starfive,jh7110-syscon.yaml
 
-STARFIVE JH71X0 USB PHY DRIVER
+STARFIVE JH71X0 PCIE AND USB PHY DRIVER
 M:	Emil Renner Berthing <kernel@esmil.dk>
 M:	Minda Chen <minda.chen@starfivetech.com>
 S:	Supported
+F:	Documentation/devicetree/bindings/phy/starfive,jh7110-pcie-phy.yaml
 F:	Documentation/devicetree/bindings/phy/starfive,jh7110-usb-phy.yaml
+F:	drivers/phy/starfive/phy-jh7110-pcie.c
 F:	drivers/phy/starfive/phy-jh7110-usb.c
 
 STATIC BRANCH/CALL
diff --git a/drivers/phy/starfive/Kconfig b/drivers/phy/starfive/Kconfig
index 2c013c390dee..c21c21d284a6 100644
--- a/drivers/phy/starfive/Kconfig
+++ b/drivers/phy/starfive/Kconfig
@@ -12,6 +12,17 @@  config PHY_STARFIVE_DPHY_RX
 	  system. If M is selected, the module will be called
 	  phy-starfive-dphy-rx.
 
+config PHY_STARFIVE_JH7110_PCIE
+	tristate "Starfive JH7110 PCIE 2.0/USB 3.0 PHY support"
+	depends on USB_SUPPORT
+	select GENERIC_PHY
+	select USB_PHY
+	help
+	  Enable this to support the StarFive PCIe 2.0 PHY,
+	  or used as USB 3.0 PHY.
+	  If M is selected, the module will be called
+	  phy-jh7110-pcie.ko.
+
 config PHY_STARFIVE_JH7110_USB
 	tristate "Starfive JH7110 USB 2.0 PHY support"
 	depends on USB_SUPPORT
diff --git a/drivers/phy/starfive/Makefile b/drivers/phy/starfive/Makefile
index 176443852f4d..03a55aad53a2 100644
--- a/drivers/phy/starfive/Makefile
+++ b/drivers/phy/starfive/Makefile
@@ -1,3 +1,4 @@ 
 # SPDX-License-Identifier: GPL-2.0
 obj-$(CONFIG_PHY_STARFIVE_DPHY_RX)      += phy-starfive-dphy-rx.o
+obj-$(CONFIG_PHY_STARFIVE_JH7110_PCIE)	+= phy-jh7110-pcie.o
 obj-$(CONFIG_PHY_STARFIVE_JH7110_USB)	+= phy-jh7110-usb.o
diff --git a/drivers/phy/starfive/phy-jh7110-pcie.c b/drivers/phy/starfive/phy-jh7110-pcie.c
new file mode 100644
index 000000000000..725815aabe74
--- /dev/null
+++ b/drivers/phy/starfive/phy-jh7110-pcie.c
@@ -0,0 +1,197 @@ 
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * StarFive JH7110 PCIe 2.0 PHY driver
+ *
+ * Copyright (C) 2023 Minda Chen <minda.chen@starfivetech.com>
+ */
+
+#include <linux/bits.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/mfd/syscon.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#define PCIE_KVCO_LEVEL_OFF		(0x28)
+#define PCIE_USB3_PHY_PLL_CTL_OFF	(0x7c)
+#define PCIE_KVCO_TUNE_SIGNAL_OFF	(0x80)
+#define PCIE_USB3_PHY_ENABLE		BIT(4)
+#define PHY_KVCO_FINE_TUNE_LEVEL	0x91
+#define PHY_KVCO_FINE_TUNE_SIGNALS	0xc
+
+#define USB_PDRSTN_SPLIT		BIT(17)
+
+#define PCIE_CKREF_SRC_MASK		GENMASK(19, 18)
+#define PCIE_CLK_SEL_MASK		GENMASK(21, 20)
+#define PCIE_PHY_MODE			BIT(20)
+#define PCIE_PHY_MODE_MASK		GENMASK(21, 20)
+#define PCIE_USB3_BUS_WIDTH_MASK	GENMASK(3, 2)
+#define PCIE_USB3_RATE_MASK		GENMASK(6, 5)
+#define PCIE_USB3_RX_STANDBY_MASK	BIT(7)
+#define PCIE_USB3_PHY_ENABLE		BIT(4)
+
+struct jh7110_pcie_phy {
+	struct phy *phy;
+	struct regmap *stg_syscon;
+	struct regmap *sys_syscon;
+	void __iomem *regs;
+	u32 sys_phy_connect;
+	u32 stg_pcie_mode;
+	u32 stg_pcie_usb;
+	enum phy_mode mode;
+};
+
+static int jh7110_usb3_mode_set(struct jh7110_pcie_phy *data)
+{
+	if (!data->stg_syscon || !data->sys_syscon) {
+		dev_info(&data->phy->dev, "don't support usb3 mode\n");
+		return -EINVAL;
+	}
+
+	regmap_update_bits(data->stg_syscon, data->stg_pcie_mode,
+		PCIE_PHY_MODE_MASK, PCIE_PHY_MODE);
+	regmap_update_bits(data->stg_syscon, data->stg_pcie_usb,
+		PCIE_USB3_BUS_WIDTH_MASK, 0);
+	regmap_update_bits(data->stg_syscon, data->stg_pcie_usb,
+		PCIE_USB3_RATE_MASK, 0);
+	regmap_update_bits(data->stg_syscon, data->stg_pcie_usb,
+		PCIE_USB3_RX_STANDBY_MASK, 0);
+	regmap_update_bits(data->stg_syscon, data->stg_pcie_usb,
+		PCIE_USB3_PHY_ENABLE, PCIE_USB3_PHY_ENABLE);
+
+	/* Connect usb 3.0 phy mode */
+	regmap_update_bits(data->sys_syscon, data->sys_phy_connect,
+		USB_PDRSTN_SPLIT, 0);
+
+	/* Configuare spread-spectrum mode: down-spread-spectrum */
+	writel(PCIE_USB3_PHY_ENABLE, data->regs + PCIE_USB3_PHY_PLL_CTL_OFF);
+
+	return 0;
+}
+
+static void jh7110_pcie_mode_set(struct jh7110_pcie_phy *phy)
+{
+	/* PCIe Multi-PHY PLL KVCO Gain fine tune settings: */
+	writel(PHY_KVCO_FINE_TUNE_LEVEL, phy->regs + PCIE_KVCO_LEVEL_OFF);
+	writel(PHY_KVCO_FINE_TUNE_SIGNALS, phy->regs + PCIE_KVCO_TUNE_SIGNAL_OFF);
+}
+
+static int jh7110_pcie_phy_set_mode(struct phy *_phy,
+				  enum phy_mode mode, int submode)
+{
+	struct jh7110_pcie_phy *phy = phy_get_drvdata(_phy);
+	int ret;
+
+	if (mode != phy->mode) {
+		switch (mode) {
+		case PHY_MODE_USB_HOST:
+		case PHY_MODE_USB_DEVICE:
+		case PHY_MODE_USB_OTG:
+			ret = jh7110_usb3_mode_set(phy);
+			if (ret)
+				return ret;
+			break;
+		case PHY_MODE_PCIE:
+			jh7110_pcie_mode_set(phy);
+			break;
+		default:
+			return -EINVAL;
+		}
+
+		dev_info(&_phy->dev, "Changing phy mode to %d\n", mode);
+		phy->mode = mode;
+	}
+
+	return 0;
+}
+
+static int jh7110_pcie_phy_init(struct phy *_phy)
+{
+	return 0;
+}
+
+static int jh7110_pcie_phy_exit(struct phy *_phy)
+{
+	return 0;
+}
+
+static const struct phy_ops jh7110_pcie_phy_ops = {
+	.init		= jh7110_pcie_phy_init,
+	.exit		= jh7110_pcie_phy_exit,
+	.set_mode	= jh7110_pcie_phy_set_mode,
+	.owner		= THIS_MODULE,
+};
+
+static int jh7110_pcie_phy_probe(struct platform_device *pdev)
+{
+	struct jh7110_pcie_phy *phy;
+	struct device *dev = &pdev->dev;
+	struct phy_provider *phy_provider;
+	u32 args[3];
+
+	phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
+	if (!phy)
+		return -ENOMEM;
+
+	phy->regs = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(phy->regs))
+		return PTR_ERR(phy->regs);
+
+	phy->phy = devm_phy_create(dev, NULL, &jh7110_pcie_phy_ops);
+	if (IS_ERR(phy->phy))
+		return dev_err_probe(dev, PTR_ERR(phy->regs),
+			"Failed to map phy base\n");
+
+	phy->sys_syscon = syscon_regmap_lookup_by_phandle_args(pdev->dev.of_node,
+		"starfive,sys-syscon", 1, args);
+
+	if (!IS_ERR_OR_NULL(phy->sys_syscon))
+		phy->sys_phy_connect = args[0];
+	else
+		phy->sys_syscon = NULL;
+
+	phy->stg_syscon = syscon_regmap_lookup_by_phandle_args(pdev->dev.of_node,
+		"starfive,stg-syscon", 2, args);
+
+	if (!IS_ERR_OR_NULL(phy->stg_syscon)) {
+		phy->stg_pcie_mode = args[0];
+		phy->stg_pcie_usb = args[1];
+	} else
+		phy->stg_syscon = NULL;
+
+	platform_set_drvdata(pdev, phy);
+	phy_set_drvdata(phy->phy, phy);
+	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+
+	return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static int jh7110_pcie_phy_remove(struct platform_device *pdev)
+{
+	platform_set_drvdata(pdev, NULL);
+
+	return 0;
+}
+
+static const struct of_device_id jh7110_pcie_phy_of_match[] = {
+	{ .compatible = "starfive,jh7110-pcie-phy" },
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, jh7110_pcie_phy_of_match);
+
+static struct platform_driver jh7110_pcie_phy_driver = {
+	.probe	= jh7110_pcie_phy_probe,
+	.remove	= jh7110_pcie_phy_remove,
+	.driver = {
+		.of_match_table	= jh7110_pcie_phy_of_match,
+		.name  = "jh7110-pcie-phy",
+	}
+};
+module_platform_driver(jh7110_pcie_phy_driver);
+
+MODULE_DESCRIPTION("StarFive JH7110 PCIe 2.0 PHY driver");
+MODULE_AUTHOR("Minda Chen <minda.chen@starfivetech.com>");
+MODULE_LICENSE("GPL");