[v3,1/2] arm64: dts: rk3399-pinephone-pro: Add internal display support
Commit Message
From: Martijn Braam <martijn@brixit.nl>
The phone's display is using a Hannstar LCD panel. Support it by adding a
panel DT node and all needed nodes (backlight, MIPI DSI, regulators, etc).
Signed-off-by: Martijn Braam <martijn@brixit.nl>
Co-developed-by: Kamil Trzciński <ayufan@ayufan.eu>
Signed-off-by: Kamil Trzciński <ayufan@ayufan.eu>
Co-developed-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Ondrej Jirman <megi@xff.cz>
---
Changes in v3:
- Fix some ./scripts/checkpatch.pl --strict warnings.
- Add Ondrej Jirman Tested-by tag.
- Change PWM period to 50000 since 20 kHz is recommended (Ondrej Jirman).
- Remove useless comments for the panel regulators (Ondrej Jirman).
- Drop unneeded pinctrl pull down conf for pins that either already have
a pull-down resistor or are already driven by the SoC (Ondrej Jirman).
- Remove "pwm-delay-us" property not supported in mainline (Ondrej Jirman).
Changes in v2:
- Drop touchscreen node because used the wrong compatible (Ondrej Jirman).
- Fix assigned-clock-parents in vopb node (Ondrej Jirman).
- Add vopl and vopl nodes.
.../dts/rockchip/rk3399-pinephone-pro.dts | 95 +++++++++++++++++++
1 file changed, 95 insertions(+)
@@ -29,6 +29,11 @@ chosen {
stdout-path = "serial2:115200n8";
};
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm0 0 50000 0>;
+ };
+
gpio-keys {
compatible = "gpio-keys";
pinctrl-names = "default";
@@ -102,6 +107,30 @@ wifi_pwrseq: sdio-wifi-pwrseq {
/* WL_REG_ON on module */
reset-gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>;
};
+
+ /* MIPI DSI panel 1.8v supply */
+ vcc1v8_lcd: vcc1v8-lcd {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ regulator-name = "vcc1v8_lcd";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc3v3_sys>;
+ gpio = <&gpio3 RK_PA5 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ };
+
+ /* MIPI DSI panel 2.8v supply */
+ vcc2v8_lcd: vcc2v8-lcd {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ regulator-name = "vcc2v8_lcd";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ vin-supply = <&vcc3v3_sys>;
+ gpio = <&gpio3 RK_PA1 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ };
};
&cpu_alert0 {
@@ -139,6 +168,11 @@ &emmc_phy {
status = "okay";
};
+&gpu {
+ mali-supply = <&vdd_gpu>;
+ status = "okay";
+};
+
&i2c0 {
clock-frequency = <400000>;
i2c-scl-rising-time-ns = <168>;
@@ -362,6 +396,39 @@ &io_domains {
status = "okay";
};
+&mipi_dsi {
+ status = "okay";
+ clock-master;
+
+ ports {
+ mipi_out: port@1 {
+ #address-cells = <0>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ mipi_out_panel: endpoint {
+ remote-endpoint = <&mipi_in_panel>;
+ };
+ };
+ };
+
+ panel@0 {
+ compatible = "hannstar,hsd060bhw4";
+ reg = <0>;
+ backlight = <&backlight>;
+ reset-gpios = <&gpio4 RK_PD1 GPIO_ACTIVE_LOW>;
+ vcc-supply = <&vcc2v8_lcd>;
+ iovcc-supply = <&vcc1v8_lcd>;
+ pinctrl-names = "default";
+
+ port {
+ mipi_in_panel: endpoint {
+ remote-endpoint = <&mipi_out_panel>;
+ };
+ };
+ };
+};
+
&pmu_io_domains {
pmu1830-supply = <&vcc_1v8>;
status = "okay";
@@ -429,6 +496,10 @@ &sdio0 {
status = "okay";
};
+&pwm0 {
+ status = "okay";
+};
+
&sdmmc {
bus-width = <4>;
cap-sd-highspeed;
@@ -479,3 +550,27 @@ bluetooth {
&uart2 {
status = "okay";
};
+
+&vopb {
+ status = "okay";
+ assigned-clocks = <&cru DCLK_VOP0_DIV>, <&cru DCLK_VOP0>,
+ <&cru ACLK_VOP0>, <&cru HCLK_VOP0>;
+ assigned-clock-rates = <0>, <0>, <400000000>, <100000000>;
+ assigned-clock-parents = <&cru PLL_GPLL>, <&cru DCLK_VOP0_DIV>;
+};
+
+&vopb_mmu {
+ status = "okay";
+};
+
+&vopl {
+ status = "okay";
+ assigned-clocks = <&cru DCLK_VOP1_DIV>, <&cru DCLK_VOP1>,
+ <&cru ACLK_VOP1>, <&cru HCLK_VOP1>;
+ assigned-clock-rates = <0>, <0>, <400000000>, <100000000>;
+ assigned-clock-parents = <&cru PLL_GPLL>, <&cru DCLK_VOP1_DIV>;
+};
+
+&vopl_mmu {
+ status = "okay";
+};