@@ -15,3 +15,11 @@ config NET_DSA_QCA8K
help
This enables support for the Qualcomm Atheros QCA8K Ethernet
switch chips.
+
+config NET_DSA_QCA8K_LEDS_SUPPORT
+ bool "Qualcomm Atheros QCA8K Ethernet switch family LEDs support"
+ depends on NET_DSA_QCA8K
+ depends on LEDS_CLASS
+ help
+ This enabled support for LEDs present on the Qualcomm Atheros
+ QCA8K Ethernet switch chips.
@@ -2,3 +2,6 @@
obj-$(CONFIG_NET_DSA_AR9331) += ar9331.o
obj-$(CONFIG_NET_DSA_QCA8K) += qca8k.o
qca8k-y += qca8k-common.o qca8k-8xxx.o
+ifdef CONFIG_NET_DSA_QCA8K_LEDS_SUPPORT
+qca8k-y += qca8k-leds.o
+endif
@@ -22,6 +22,7 @@
#include <linux/dsa/tag_qca.h>
#include "qca8k.h"
+#include "qca8k_leds.h"
static void
qca8k_split_addr(u32 regaddr, u16 *r1, u16 *r2, u16 *page)
@@ -1783,6 +1784,10 @@ qca8k_setup(struct dsa_switch *ds)
if (ret)
return ret;
+ ret = qca8k_setup_led_ctrl(priv);
+ if (ret)
+ return ret;
+
qca8k_setup_pcs(priv, &priv->pcs_port_0, 0);
qca8k_setup_pcs(priv, &priv->pcs_port_6, 6);
new file mode 100644
@@ -0,0 +1,232 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/regmap.h>
+#include <net/dsa.h>
+
+#include "qca8k.h"
+#include "qca8k_leds.h"
+
+static int
+qca8k_get_enable_led_reg(int port_num, int led_num, struct qca8k_led_pattern_en *reg_info)
+{
+ switch (port_num) {
+ case 0:
+ reg_info->reg = QCA8K_LED_CTRL_REG(led_num);
+ reg_info->shift = QCA8K_LED_PHY0123_CONTROL_RULE_SHIFT;
+ break;
+ case 1:
+ case 2:
+ case 3:
+ /* Port 123 are controlled on a different reg */
+ reg_info->reg = QCA8K_LED_CTRL3_REG;
+ reg_info->shift = QCA8K_LED_PHY123_PATTERN_EN_SHIFT(port_num, led_num);
+ break;
+ case 4:
+ reg_info->reg = QCA8K_LED_CTRL_REG(led_num);
+ reg_info->shift = QCA8K_LED_PHY4_CONTROL_RULE_SHIFT;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int
+qca8k_led_brightness_set(struct qca8k_led *led,
+ enum led_brightness brightness)
+{
+ struct qca8k_led_pattern_en reg_info;
+ struct qca8k_priv *priv = led->priv;
+ u32 mask, val;
+
+ qca8k_get_enable_led_reg(led->port_num, led->led_num, ®_info);
+
+ val = QCA8K_LED_ALWAYS_OFF;
+ if (brightness)
+ val = QCA8K_LED_ALWAYS_ON;
+
+ /* HW regs to control brightness is special and port 1-2-3
+ * are placed in a different reg.
+ *
+ * To control port 0 brightness:
+ * - the 2 bit (15, 14) of:
+ * - QCA8K_LED_CTRL0_REG for led1
+ * - QCA8K_LED_CTRL1_REG for led2
+ * - QCA8K_LED_CTRL2_REG for led3
+ *
+ * To control port 4:
+ * - the 2 bit (31, 30) of:
+ * - QCA8K_LED_CTRL0_REG for led1
+ * - QCA8K_LED_CTRL1_REG for led2
+ * - QCA8K_LED_CTRL2_REG for led3
+ *
+ * To control port 1:
+ * - the 2 bit at (9, 8) of QCA8K_LED_CTRL3_REG are used for led1
+ * - the 2 bit at (11, 10) of QCA8K_LED_CTRL3_REG are used for led2
+ * - the 2 bit at (13, 12) of QCA8K_LED_CTRL3_REG are used for led3
+ *
+ * To control port 2:
+ * - the 2 bit at (15, 14) of QCA8K_LED_CTRL3_REG are used for led1
+ * - the 2 bit at (17, 16) of QCA8K_LED_CTRL3_REG are used for led2
+ * - the 2 bit at (19, 18) of QCA8K_LED_CTRL3_REG are used for led3
+ *
+ * To control port 3:
+ * - the 2 bit at (21, 20) of QCA8K_LED_CTRL3_REG are used for led1
+ * - the 2 bit at (23, 22) of QCA8K_LED_CTRL3_REG are used for led2
+ * - the 2 bit at (25, 24) of QCA8K_LED_CTRL3_REG are used for led3
+ *
+ * To abstract this and have less code, we use the port and led numm
+ * to calculate the shift and the correct reg due to this problem of
+ * not having a 1:1 map of LED with the regs.
+ */
+ if (led->port_num == 0 || led->port_num == 4) {
+ mask = QCA8K_LED_PATTERN_EN_MASK;
+ val <<= QCA8K_LED_PATTERN_EN_SHIFT;
+ } else {
+ mask = QCA8K_LED_PHY123_PATTERN_EN_MASK;
+ }
+
+ return regmap_update_bits(priv->regmap, reg_info.reg,
+ mask << reg_info.shift,
+ val << reg_info.shift);
+}
+
+static int
+qca8k_cled_brightness_set_blocking(struct led_classdev *ldev,
+ enum led_brightness brightness)
+{
+ struct qca8k_led *led = container_of(ldev, struct qca8k_led, cdev);
+
+ return qca8k_led_brightness_set(led, brightness);
+}
+
+static enum led_brightness
+qca8k_led_brightness_get(struct qca8k_led *led)
+{
+ struct qca8k_led_pattern_en reg_info;
+ struct qca8k_priv *priv = led->priv;
+ u32 val;
+ int ret;
+
+ qca8k_get_enable_led_reg(led->port_num, led->led_num, ®_info);
+
+ ret = regmap_read(priv->regmap, reg_info.reg, &val);
+ if (ret)
+ return 0;
+
+ val >>= reg_info.shift;
+
+ if (led->port_num == 0 || led->port_num == 4) {
+ val &= QCA8K_LED_PATTERN_EN_MASK;
+ val >>= QCA8K_LED_PATTERN_EN_SHIFT;
+ } else {
+ val &= QCA8K_LED_PHY123_PATTERN_EN_MASK;
+ }
+
+ /* Assume brightness ON only when the LED is set to always ON */
+ return val == QCA8K_LED_ALWAYS_ON;
+}
+
+static int
+qca8k_parse_port_leds(struct qca8k_priv *priv, struct fwnode_handle *port, int port_num)
+{
+ struct fwnode_handle *led = NULL, *leds = NULL;
+ struct led_init_data init_data = { };
+ enum led_default_state state;
+ struct qca8k_led *port_led;
+ int led_num, led_index;
+ int ret;
+
+ leds = fwnode_get_named_child_node(port, "leds");
+ if (!leds) {
+ dev_dbg(priv->dev, "No Leds node specified in device tree for port %d!\n",
+ port_num);
+ return 0;
+ }
+
+ fwnode_for_each_child_node(leds, led) {
+ /* Reg represent the led number of the port.
+ * Each port can have at most 3 leds attached
+ * Commonly:
+ * 1. is gigabit led
+ * 2. is mbit led
+ * 3. additional status led
+ */
+ if (fwnode_property_read_u32(led, "reg", &led_num))
+ continue;
+
+ if (led_num >= QCA8K_LED_PORT_COUNT) {
+ dev_warn(priv->dev, "Invalid LED reg %d defined for port %d",
+ led_num, port_num);
+ continue;
+ }
+
+ led_index = QCA8K_LED_PORT_INDEX(port_num, led_num);
+
+ port_led = &priv->ports_led[led_index];
+ port_led->port_num = port_num;
+ port_led->led_num = led_num;
+ port_led->priv = priv;
+
+ state = led_init_default_state_get(led);
+ switch (state) {
+ case LEDS_DEFSTATE_ON:
+ port_led->cdev.brightness = 1;
+ qca8k_led_brightness_set(port_led, 1);
+ break;
+ case LEDS_DEFSTATE_KEEP:
+ port_led->cdev.brightness =
+ qca8k_led_brightness_get(port_led);
+ break;
+ default:
+ port_led->cdev.brightness = 0;
+ qca8k_led_brightness_set(port_led, 0);
+ }
+
+ port_led->cdev.max_brightness = 1;
+ port_led->cdev.brightness_set_blocking = qca8k_cled_brightness_set_blocking;
+ init_data.default_label = ":port";
+ init_data.devicename = "qca8k";
+ init_data.fwnode = led;
+
+ ret = devm_led_classdev_register_ext(priv->dev, &port_led->cdev, &init_data);
+ if (ret)
+ dev_warn(priv->dev, "Failed to init LED %d for port %d", led_num, port_num);
+ }
+
+ return 0;
+}
+
+int
+qca8k_setup_led_ctrl(struct qca8k_priv *priv)
+{
+ struct fwnode_handle *ports, *port;
+ int port_num;
+ int ret;
+
+ ports = device_get_named_child_node(priv->dev, "ports");
+ if (!ports) {
+ dev_info(priv->dev, "No ports node specified in device tree!");
+ return 0;
+ }
+
+ fwnode_for_each_child_node(ports, port) {
+ if (fwnode_property_read_u32(port, "reg", &port_num))
+ continue;
+
+ /* Skip checking for CPU port 0 and CPU port 6 as not supported */
+ if (port_num == 0 || port_num == 6)
+ continue;
+
+ /* Each port can have at most 3 different leds attached.
+ * Switch port starts from 0 to 6, but port 0 and 6 are CPU
+ * port. The port index needs to be decreased by one to identify
+ * the correct port for LED setup.
+ */
+ ret = qca8k_parse_port_leds(priv, port, qca8k_port_to_phy(port_num));
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
@@ -11,6 +11,7 @@
#include <linux/delay.h>
#include <linux/regmap.h>
#include <linux/gpio.h>
+#include <linux/leds.h>
#include <linux/dsa/tag_qca.h>
#define QCA8K_ETHERNET_MDIO_PRIORITY 7
@@ -85,6 +86,51 @@
#define QCA8K_MDIO_MASTER_DATA(x) FIELD_PREP(QCA8K_MDIO_MASTER_DATA_MASK, x)
#define QCA8K_MDIO_MASTER_MAX_PORTS 5
#define QCA8K_MDIO_MASTER_MAX_REG 32
+
+/* LED control register */
+#define QCA8K_LED_PORT_COUNT 3
+#define QCA8K_LED_COUNT ((QCA8K_NUM_PORTS - QCA8K_NUM_CPU_PORTS) * QCA8K_LED_PORT_COUNT)
+#define QCA8K_LED_RULE_COUNT 6
+#define QCA8K_LED_RULE_MAX 11
+#define QCA8K_LED_PORT_INDEX(_phy, _led) (((_phy) * QCA8K_LED_PORT_COUNT) + (_led))
+
+#define QCA8K_LED_PHY123_PATTERN_EN_SHIFT(_phy, _led) ((((_phy) - 1) * 6) + 8 + (2 * (_led)))
+#define QCA8K_LED_PHY123_PATTERN_EN_MASK GENMASK(1, 0)
+
+#define QCA8K_LED_PHY0123_CONTROL_RULE_SHIFT 0
+#define QCA8K_LED_PHY4_CONTROL_RULE_SHIFT 16
+
+#define QCA8K_LED_CTRL_REG(_i) (0x050 + (_i) * 4)
+#define QCA8K_LED_CTRL0_REG 0x50
+#define QCA8K_LED_CTRL1_REG 0x54
+#define QCA8K_LED_CTRL2_REG 0x58
+#define QCA8K_LED_CTRL3_REG 0x5C
+#define QCA8K_LED_CTRL_SHIFT(_i) (((_i) % 2) * 16)
+#define QCA8K_LED_CTRL_MASK GENMASK(15, 0)
+#define QCA8K_LED_RULE_MASK GENMASK(13, 0)
+#define QCA8K_LED_BLINK_FREQ_MASK GENMASK(1, 0)
+#define QCA8K_LED_BLINK_FREQ_SHITF 0
+#define QCA8K_LED_BLINK_2HZ 0
+#define QCA8K_LED_BLINK_4HZ 1
+#define QCA8K_LED_BLINK_8HZ 2
+#define QCA8K_LED_BLINK_AUTO 3
+#define QCA8K_LED_LINKUP_OVER_MASK BIT(2)
+#define QCA8K_LED_TX_BLINK_MASK BIT(4)
+#define QCA8K_LED_RX_BLINK_MASK BIT(5)
+#define QCA8K_LED_COL_BLINK_MASK BIT(7)
+#define QCA8K_LED_LINK_10M_EN_MASK BIT(8)
+#define QCA8K_LED_LINK_100M_EN_MASK BIT(9)
+#define QCA8K_LED_LINK_1000M_EN_MASK BIT(10)
+#define QCA8K_LED_POWER_ON_LIGHT_MASK BIT(11)
+#define QCA8K_LED_HALF_DUPLEX_MASK BIT(12)
+#define QCA8K_LED_FULL_DUPLEX_MASK BIT(13)
+#define QCA8K_LED_PATTERN_EN_MASK GENMASK(15, 14)
+#define QCA8K_LED_PATTERN_EN_SHIFT 14
+#define QCA8K_LED_ALWAYS_OFF 0
+#define QCA8K_LED_ALWAYS_BLINK_4HZ 1
+#define QCA8K_LED_ALWAYS_ON 2
+#define QCA8K_LED_RULE_CONTROLLED 3
+
#define QCA8K_GOL_MAC_ADDR0 0x60
#define QCA8K_GOL_MAC_ADDR1 0x64
#define QCA8K_MAX_FRAME_SIZE 0x78
@@ -382,6 +428,19 @@ struct qca8k_pcs {
int port;
};
+struct qca8k_led_pattern_en {
+ u32 reg;
+ u8 shift;
+};
+
+struct qca8k_led {
+ u8 port_num;
+ u8 led_num;
+ u16 old_rule;
+ struct qca8k_priv *priv;
+ struct led_classdev cdev;
+};
+
struct qca8k_priv {
u8 switch_id;
u8 switch_revision;
@@ -406,6 +465,7 @@ struct qca8k_priv {
struct qca8k_pcs pcs_port_0;
struct qca8k_pcs pcs_port_6;
const struct qca8k_match_data *info;
+ struct qca8k_led ports_led[QCA8K_LED_COUNT];
};
struct qca8k_mib_desc {
new file mode 100644
@@ -0,0 +1,16 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+#ifndef __QCA8K_LEDS_H
+#define __QCA8K_LEDS_H
+
+/* Leds Support function */
+#ifdef CONFIG_NET_DSA_QCA8K_LEDS_SUPPORT
+int qca8k_setup_led_ctrl(struct qca8k_priv *priv);
+#else
+static inline int qca8k_setup_led_ctrl(struct qca8k_priv *priv)
+{
+ return 0;
+}
+#endif
+
+#endif /* __QCA8K_LEDS_H */