diff mbox series

[1/3] usb: dwc3-am62: Add support for system wakeup based on USB events

Message ID 20230316131226.89540-2-rogerq@kernel.org
State New
Headers
Series usb: dwc3-am62: Add system wake-up support |

Commit Message

Roger Quadros March 16, 2023, 1:12 p.m. UTC 
  From: Aswath Govindraju <a-govindraju@ti.com>

The USB2SS IP in TI's AM62 SoC is capable of supporting wakeup from
deep sleep based on the following events,

1) VBUS state change
2) Overcurrent detection
3) Line state change

Wakeup from these events can enabled by setting their corresponding bits
in the WAKEUP_CONFIG register. The events to be enabled are decided based
on the current role of the controller.

When the role of the controller is host, the comparators for detecting
VBUS state change are disabled while entering low power mode. This is done
as VBUS state is not used in host mode and disabling the comparators helps
in reducing the power consumption. So, wakeup from VBUS state change should
be disabled in host mode. While operating in peripheral mode all the wakeup
events can be enabled.

Therefore, add support for the same in the suspend/resume hooks.

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Roger Quadros <rogerq@kernel.org>
---
 drivers/usb/dwc3/dwc3-am62.c | 39 ++++++++++++++++++++++++++++++++++++
 1 file changed, 39 insertions(+)
diff mbox series

Patch

diff --git a/drivers/usb/dwc3/dwc3-am62.c b/drivers/usb/dwc3/dwc3-am62.c
index 173cf3579c55..867bfa1252b8 100644
--- a/drivers/usb/dwc3/dwc3-am62.c
+++ b/drivers/usb/dwc3/dwc3-am62.c
@@ -17,6 +17,8 @@ 
 #include <linux/regmap.h>
 #include <linux/pinctrl/consumer.h>
 
+#include "core.h"
+
 /* USB WRAPPER register offsets */
 #define USBSS_PID			0x0
 #define USBSS_OVERCURRENT_CTRL		0x4
@@ -45,6 +47,10 @@ 
 #define USBSS_PHY_VBUS_SEL_SHIFT	1
 #define USBSS_PHY_LANE_REVERSE		BIT(0)
 
+/* CORE STAT register bits */
+#define USBSS_CORE_OPERATIONAL_MODE_MASK	GENMASK(13, 12)
+#define USBSS_CORE_OPERATIONAL_MODE_SHIFT	12
+
 /* MODE CONTROL register bits */
 #define USBSS_MODE_VALID	BIT(0)
 
@@ -233,6 +239,9 @@  static int dwc3_ti_probe(struct platform_device *pdev)
 	reg |= USBSS_MODE_VALID;
 	dwc3_ti_writel(data, USBSS_MODE_CONTROL, reg);
 
+	/* Device has capability to wakeup system from sleep */
+	device_set_wakeup_capable(dev, true);
+
 	/* Setting up autosuspend */
 	pm_runtime_set_autosuspend_delay(dev, DWC3_AM62_AUTOSUSPEND_DELAY);
 	pm_runtime_use_autosuspend(dev);
@@ -281,6 +290,22 @@  static int dwc3_ti_remove(struct platform_device *pdev)
 static int dwc3_ti_suspend_common(struct device *dev)
 {
 	struct dwc3_data *data = dev_get_drvdata(dev);
+	u32 reg, current_prtcap_dir;
+
+	if (device_may_wakeup(dev)) {
+		reg = dwc3_ti_readl(data, USBSS_CORE_STAT);
+		current_prtcap_dir = (reg & USBSS_CORE_OPERATIONAL_MODE_MASK)
+				     >> USBSS_CORE_OPERATIONAL_MODE_SHIFT;
+		/* Set wakeup config enable bits */
+		reg = dwc3_ti_readl(data, USBSS_WAKEUP_CONFIG);
+		if (current_prtcap_dir == DWC3_GCTL_PRTCAP_HOST) {
+			reg |= USBSS_WAKEUP_CFG_LINESTATE_EN | USBSS_WAKEUP_CFG_OVERCURRENT_EN;
+		} else {
+			reg |= USBSS_WAKEUP_CFG_OVERCURRENT_EN | USBSS_WAKEUP_CFG_LINESTATE_EN |
+			       USBSS_WAKEUP_CFG_VBUSVALID_EN;
+		}
+		dwc3_ti_writel(data, USBSS_WAKEUP_CONFIG, reg);
+	}
 
 	clk_disable_unprepare(data->usb2_refclk);
 
@@ -290,9 +315,23 @@  static int dwc3_ti_suspend_common(struct device *dev)
 static int dwc3_ti_resume_common(struct device *dev)
 {
 	struct dwc3_data *data = dev_get_drvdata(dev);
+	u32 reg;
 
 	clk_prepare_enable(data->usb2_refclk);
 
+	if (device_may_wakeup(dev)) {
+		/* Clear wakeup config enable bits */
+		reg = dwc3_ti_readl(data, USBSS_WAKEUP_CONFIG);
+		reg &= ~(USBSS_WAKEUP_CFG_OVERCURRENT_EN | USBSS_WAKEUP_CFG_LINESTATE_EN |
+			 USBSS_WAKEUP_CFG_VBUSVALID_EN);
+		dwc3_ti_writel(data, USBSS_WAKEUP_CONFIG, reg);
+	}
+
+	reg = dwc3_ti_readl(data, USBSS_WAKEUP_STAT);
+	/* Clear the wakeup status with wakeup clear bit */
+	reg |= USBSS_WAKEUP_STAT_CLR;
+	dwc3_ti_writel(data, USBSS_WAKEUP_STAT, reg);
+
 	return 0;
 }