[30/32] pata_parport-bpck6: move defines and mode_map to bpck6.c
Commit Message
Move all register definitions and mode_map to bpck6.c
Signed-off-by: Ondrej Zary <linux@zary.sk>
---
drivers/ata/pata_parport/bpck6.c | 44 ++++++++++++++++++++++++
drivers/ata/pata_parport/ppc6lnx.c | 54 ------------------------------
2 files changed, 44 insertions(+), 54 deletions(-)
@@ -19,6 +19,50 @@
#include "pata_parport.h"
#include "ppc6lnx.c"
+/* 60772 Commands */
+#define ACCESS_REG 0x00
+#define ACCESS_PORT 0x40
+
+#define ACCESS_READ 0x00
+#define ACCESS_WRITE 0x20
+
+/* 60772 Command Prefix */
+#define CMD_PREFIX_SET 0xe0 // Special command that modifies next command's operation
+#define CMD_PREFIX_RESET 0xc0 // Resets current cmd modifier reg bits
+ #define PREFIX_IO16 0x01 // perform 16-bit wide I/O
+ #define PREFIX_FASTWR 0x04 // enable PPC mode fast-write
+ #define PREFIX_BLK 0x08 // enable block transfer mode
+
+/* 60772 Registers */
+#define REG_STATUS 0x00 // status register
+ #define STATUS_IRQA 0x01 // Peripheral IRQA line
+ #define STATUS_EEPROM_DO 0x40 // Serial EEPROM data bit
+#define REG_VERSION 0x01 // PPC version register (read)
+#define REG_HWCFG 0x02 // Hardware Config register
+#define REG_RAMSIZE 0x03 // Size of RAM Buffer
+ #define RAMSIZE_128K 0x02
+#define REG_EEPROM 0x06 // EEPROM control register
+ #define EEPROM_SK 0x01 // eeprom SK bit
+ #define EEPROM_DI 0x02 // eeprom DI bit
+ #define EEPROM_CS 0x04 // eeprom CS bit
+ #define EEPROM_EN 0x08 // eeprom output enable
+#define REG_BLKSIZE 0x08 // Block transfer len (24 bit)
+
+/* flags */
+#define fifo_wait 0x10
+
+/* DONT CHANGE THESE LEST YOU BREAK EVERYTHING - BIT FIELD DEPENDENCIES */
+#define PPCMODE_UNI_SW 0
+#define PPCMODE_UNI_FW 1
+#define PPCMODE_BI_SW 2
+#define PPCMODE_BI_FW 3
+#define PPCMODE_EPP_BYTE 4
+#define PPCMODE_EPP_WORD 5
+#define PPCMODE_EPP_DWORD 6
+
+int mode_map[] = { PPCMODE_UNI_FW, PPCMODE_BI_FW, PPCMODE_EPP_BYTE,
+ PPCMODE_EPP_WORD, PPCMODE_EPP_DWORD };
+
static void bpck6_send_cmd(struct pi_adapter *pi, u8 cmd)
{
switch (mode_map[pi->mode]) {
@@ -15,57 +15,3 @@
//***************************************************************************
-// 60772 Commands
-
-#define ACCESS_REG 0x00
-#define ACCESS_PORT 0x40
-
-#define ACCESS_READ 0x00
-#define ACCESS_WRITE 0x20
-
-// 60772 Command Prefix
-
-#define CMD_PREFIX_SET 0xe0 // Special command that modifies the next command's operation
-#define CMD_PREFIX_RESET 0xc0 // Resets current cmd modifier reg bits
- #define PREFIX_IO16 0x01 // perform 16-bit wide I/O
- #define PREFIX_FASTWR 0x04 // enable PPC mode fast-write
- #define PREFIX_BLK 0x08 // enable block transfer mode
-
-// 60772 Registers
-
-#define REG_STATUS 0x00 // status register
- #define STATUS_IRQA 0x01 // Peripheral IRQA line
- #define STATUS_EEPROM_DO 0x40 // Serial EEPROM data bit
-#define REG_VERSION 0x01 // PPC version register (read)
-#define REG_HWCFG 0x02 // Hardware Config register
-#define REG_RAMSIZE 0x03 // Size of RAM Buffer
- #define RAMSIZE_128K 0x02
-#define REG_EEPROM 0x06 // EEPROM control register
- #define EEPROM_SK 0x01 // eeprom SK bit
- #define EEPROM_DI 0x02 // eeprom DI bit
- #define EEPROM_CS 0x04 // eeprom CS bit
- #define EEPROM_EN 0x08 // eeprom output enable
-#define REG_BLKSIZE 0x08 // Block transfer len (24 bit)
-
-//***************************************************************************
-
-// ppc_flags
-
-#define fifo_wait 0x10
-
-//***************************************************************************
-
-// DONT CHANGE THESE LEST YOU BREAK EVERYTHING - BIT FIELD DEPENDENCIES
-
-#define PPCMODE_UNI_SW 0
-#define PPCMODE_UNI_FW 1
-#define PPCMODE_BI_SW 2
-#define PPCMODE_BI_FW 3
-#define PPCMODE_EPP_BYTE 4
-#define PPCMODE_EPP_WORD 5
-#define PPCMODE_EPP_DWORD 6
-
-//***************************************************************************
-
-int mode_map[] = { PPCMODE_UNI_FW, PPCMODE_BI_FW, PPCMODE_EPP_BYTE,
- PPCMODE_EPP_WORD, PPCMODE_EPP_DWORD };