[7/7] arm64: dts: qcom: ipq9574: Add PCIe PHYs and controller nodes
Commit Message
Add PCIe0, PCIe1, PCIe2, PCIe3 (and corresponding PHY) devices
found on IPQ9574 platform. The PCIe0 & PCIe1 are 1-lane Gen3
host whereas PCIe2 & PCIe3 are 2-lane Gen3 host.
Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
---
arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts | 28 ++
arch/arm64/boot/dts/qcom/ipq9574.dtsi | 477 ++++++++++++++++++-
2 files changed, 499 insertions(+), 6 deletions(-)
Comments
Hi Devi,
On 2/14/2023 10:11 PM, Devi Priya wrote:
> Add PCIe0, PCIe1, PCIe2, PCIe3 (and corresponding PHY) devices
> found on IPQ9574 platform. The PCIe0 & PCIe1 are 1-lane Gen3
> host whereas PCIe2 & PCIe3 are 2-lane Gen3 host.
>
> Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
> Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
> Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
> ---
> arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts | 28 ++
> arch/arm64/boot/dts/qcom/ipq9574.dtsi | 477 ++++++++++++++++++-
> 2 files changed, 499 insertions(+), 6 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts b/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
> index 2c8430197ec0..21b53f34ce84 100644
> --- a/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
> +++ b/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
> @@ -8,6 +8,7 @@
>
> /dts-v1/;
>
> +#include <dt-bindings/gpio/gpio.h>
> #include "ipq9574.dtsi"
>
> / {
> @@ -29,6 +30,33 @@
> status = "okay";
> };
>
> +&pcie1_phy {
> + status = "okay";
> +};
> +
> +&pcie1_x1 {
> + perst-gpios = <&tlmm 26 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
> +
> +&pcie2_phy {
> + status = "okay";
> +};
> +
> +&pcie2_x2 {
> + perst-gpios = <&tlmm 29 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
> +
> +&pcie3_phy {
> + status = "okay";
> +};
> +
> +&pcie3_x2 {
> + perst-gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
> +
> &sdhc_1 {
> pinctrl-0 = <&sdc_default_state>;
> pinctrl-names = "default";
> diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> index 062f80798ebb..a32dbdeb5bed 100644
> --- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> +++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> @@ -6,8 +6,8 @@
> * Copyright (c) 2023, Qualcomm Innovation Center, Inc. All rights reserved.
> */
>
> -#include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/clock/qcom,ipq9574-gcc.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/reset/qcom,ipq9574-gcc.h>
>
> / {
> @@ -22,11 +22,41 @@
> #clock-cells = <0>;
> };
>
> + pcie30_phy0_pipe_clk: pcie30_phy0_pipe_clk {
> + compatible = "fixed-clock";
> + clock-frequency = <250000000>;
> + #clock-cells = <0>;
> + };
> +
> + pcie30_phy1_pipe_clk: pcie30_phy1_pipe_clk {
> + compatible = "fixed-clock";
> + clock-frequency = <250000000>;
> + #clock-cells = <0>;
> + };
> +
> + pcie30_phy2_pipe_clk: pcie30_phy2_pipe_clk {
> + compatible = "fixed-clock";
> + clock-frequency = <250000000>;
> + #clock-cells = <0>;
> + };
> +
> + pcie30_phy3_pipe_clk: pcie30_phy3_pipe_clk {
> + compatible = "fixed-clock";
> + clock-frequency = <250000000>;
> + #clock-cells = <0>;
> + };
> +
> sleep_clk: sleep-clk {
> compatible = "fixed-clock";
> #clock-cells = <0>;
> };
>
> + usb3phy_0_cc_pipe_clk: usb3phy_0_cc_pipe_clk {
> + compatible = "fixed-clock";
> + clock-frequency = <125000000>;
> + #clock-cells = <0>;
> + };
> +
Why is the usb clock added here ?
> xo_board_clk: xo-board-clk {
> compatible = "fixed-clock";
> #clock-cells = <0>;
> @@ -121,6 +151,155 @@
> #size-cells = <1>;
> ranges = <0 0 0 0xffffffff>;
>
> + pcie0_phy: phy@84000 {
> + compatible = "qcom,ipq9574-qmp-gen3x1-pcie-phy";
> + reg = <0x00084000 0x1bc>; /* Serdes PLL */
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> + clocks = <&gcc GCC_PCIE0_AUX_CLK>,
> + <&gcc GCC_PCIE0_AHB_CLK>,
> + <&gcc GCC_ANOC_PCIE0_1LANE_M_CLK>,
> + <&gcc GCC_SNOC_PCIE0_1LANE_S_CLK>;
> + clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane";
> +
> + assigned-clocks = <&gcc GCC_PCIE0_AUX_CLK>;
> + assigned-clock-rates = <20000000>;
> +
> + resets = <&gcc GCC_PCIE0_PHY_BCR>,
> + <&gcc GCC_PCIE0PHY_PHY_BCR>;
> + reset-names = "phy", "common";
> +
> + status = "disabled";
> +
> + pcie0_lane: phy@84200 {
> + reg = <0x00084200 0x16c>, /* Serdes Tx */
> + <0x00084400 0x200>, /* Serdes Rx */
> + <0x00084800 0x1f0>, /* PCS: Lane0, COM, PCIE */
> + <0x00084c00 0xf4>; /* pcs_misc */
> + #phy-cells = <0>;
> +
> + clocks = <&gcc GCC_PCIE0_PIPE_CLK>;
> + clock-names = "pipe0";
> + clock-output-names = "gcc_pcie0_pipe_clk_src";
> + #clock-cells = <0>;
> + };
> + };
> +
> + pcie2_phy: phy@8c000 {
Can the phy/pcie nodes labelled in order ?
Currently it 0/2/3/1 ?
> + compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy";
> + reg = <0x0008c000 0x1bc>; /* Serdes PLL */
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + clocks = <&gcc GCC_PCIE2_AUX_CLK>,
> + <&gcc GCC_PCIE2_AHB_CLK>,
> + <&gcc GCC_ANOC_PCIE2_2LANE_M_CLK>,
> + <&gcc GCC_SNOC_PCIE2_2LANE_S_CLK>;
> + clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane";
> +
> + assigned-clocks = <&gcc GCC_PCIE2_AUX_CLK>;
> + assigned-clock-rates = <20000000>;
> +
> + resets = <&gcc GCC_PCIE2_PHY_BCR>,
> + <&gcc GCC_PCIE2PHY_PHY_BCR>;
> + reset-names = "phy", "common";
> +
> + status = "disabled";
> +
> + pcie2_lanes: phy@8c200 {
> + reg = <0x0008c200 0x16c>, /* Serdes Tx0 */
> + <0x0008c400 0x200>, /* Serdes Rx0 */
> + <0x0008d000 0x1f0>, /* PCS: Lane0, COM, PCIE */
> + <0x0008c600 0x16c>, /* Serdes Tx1 */
> + <0x0008c800 0x200>, /* Serdes Rx1 */
> + <0x0008d400 0x0f8>; /* pcs_misc */
> +
> + #phy-cells = <0>;
> +
> + clocks = <&gcc GCC_PCIE2_PIPE_CLK>;
> + clock-names = "pipe0";
> + clock-output-names = "gcc_pcie2_pipe_clk_src";
> + #clock-cells = <0>;
> + };
> + };
> +
> + pcie3_phy: phy@f4000 {
> + compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy";
> + reg = <0x000f4000 0x1bc>; /* Serdes PLL */
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + clocks = <&gcc GCC_PCIE3_AUX_CLK>,
> + <&gcc GCC_PCIE3_AHB_CLK>,
> + <&gcc GCC_ANOC_PCIE3_2LANE_M_CLK>,
> + <&gcc GCC_SNOC_PCIE3_2LANE_S_CLK>;
> + clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane";
> +
> + assigned-clocks = <&gcc GCC_PCIE3_AUX_CLK>;
> + assigned-clock-rates = <20000000>;
> +
> + resets = <&gcc GCC_PCIE3_PHY_BCR>,
> + <&gcc GCC_PCIE3PHY_PHY_BCR>;
> + reset-names = "phy", "common";
> +
> + status = "disabled";
> +
> + pcie3_lanes: phy@f4200 {
> + reg = <0x000f4200 0x16c>, /* Serdes Tx0 */
> + <0x000f4400 0x200>, /* Serdes Rx0 */
> + <0x000f5000 0x1f0>, /* PCS: Lane0, COM, PCIE */
> + <0x000f4600 0x16c>, /* Serdes Tx1 */
> + <0x000f4800 0x200>, /* Serdes Rx1 */
> + <0x000f5400 0x0f8>; /* pcs_misc */
> +
> + #phy-cells = <0>;
> +
> + clocks = <&gcc GCC_PCIE3_PIPE_CLK>;
> + clock-names = "pipe0";
> + clock-output-names = "gcc_pcie3_pipe_clk_src";
> + #clock-cells = <0>;
> + };
> + };
> +
> + pcie1_phy: phy@fc000 {
> + compatible = "qcom,ipq9574-qmp-gen3x1-pcie-phy";
> + reg = <0x000fc000 0x1bc>; /* Serdes PLL */
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + clocks = <&gcc GCC_PCIE1_AUX_CLK>,
> + <&gcc GCC_PCIE1_AHB_CLK>,
> + <&gcc GCC_ANOC_PCIE1_1LANE_M_CLK>,
> + <&gcc GCC_SNOC_PCIE1_1LANE_S_CLK>;
> + clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane";
> +
> + assigned-clocks = <&gcc GCC_PCIE1_AUX_CLK>;
> + assigned-clock-rates = <20000000>;
> +
> + resets = <&gcc GCC_PCIE1_PHY_BCR>,
> + <&gcc GCC_PCIE1PHY_PHY_BCR>;
> + reset-names = "phy", "common";
> +
> + status = "disabled";
> +
> + pcie1_lane: phy@fc200 {
> + reg = <0x000fc200 0x16c>, /* Serdes Tx */
> + <0x000fc400 0x200>, /* Serdes Rx */
> + <0x000fc800 0x1f0>, /* PCS: Lane0, COM, PCIE */
> + <0x000fcc00 0xf4>; /* pcs_misc */
> + #phy-cells = <0>;
> +
> + clocks = <&gcc GCC_PCIE1_PIPE_CLK>;
> + clock-names = "pipe0";
> + clock-output-names = "gcc_pcie1_pipe_clk_src";
> + #clock-cells = <0>;
> + };
> + };
> +
> tlmm: pinctrl@1000000 {
> compatible = "qcom,ipq9574-tlmm";
> reg = <0x01000000 0x300000>;
> @@ -145,11 +324,11 @@
> clocks = <&xo_board_clk>,
> <&sleep_clk>,
> <&bias_pll_ubi_nc_clk>,
> - <0>,
> - <0>,
> - <0>,
> - <0>,
> - <0>;
> + <&pcie30_phy0_pipe_clk>,
> + <&pcie30_phy1_pipe_clk>,
> + <&pcie30_phy2_pipe_clk>,
> + <&pcie30_phy3_pipe_clk>,
> + <&usb3phy_0_cc_pipe_clk>;
Same , why usb3 clk is added here ?
Regards,
Sricharan
On 2/17/2023 2:05 PM, Sricharan Ramabadhran wrote:
>
> Hi Devi,
>
> On 2/14/2023 10:11 PM, Devi Priya wrote:
>> Add PCIe0, PCIe1, PCIe2, PCIe3 (and corresponding PHY) devices
>> found on IPQ9574 platform. The PCIe0 & PCIe1 are 1-lane Gen3
>> host whereas PCIe2 & PCIe3 are 2-lane Gen3 host.
>>
>> Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
>> Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
>> Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
>> ---
>> arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts | 28 ++
>> arch/arm64/boot/dts/qcom/ipq9574.dtsi | 477 ++++++++++++++++++-
>> 2 files changed, 499 insertions(+), 6 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
>> b/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
>> index 2c8430197ec0..21b53f34ce84 100644
>> --- a/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
>> +++ b/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
>> @@ -8,6 +8,7 @@
>> /dts-v1/;
>> +#include <dt-bindings/gpio/gpio.h>
>> #include "ipq9574.dtsi"
>> / {
>> @@ -29,6 +30,33 @@
>> status = "okay";
>> };
>> +&pcie1_phy {
>> + status = "okay";
>> +};
>> +
>> +&pcie1_x1 {
>> + perst-gpios = <&tlmm 26 GPIO_ACTIVE_LOW>;
>> + status = "okay";
>> +};
>> +
>> +&pcie2_phy {
>> + status = "okay";
>> +};
>> +
>> +&pcie2_x2 {
>> + perst-gpios = <&tlmm 29 GPIO_ACTIVE_LOW>;
>> + status = "okay";
>> +};
>> +
>> +&pcie3_phy {
>> + status = "okay";
>> +};
>> +
>> +&pcie3_x2 {
>> + perst-gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
>> + status = "okay";
>> +};
>> +
>> &sdhc_1 {
>> pinctrl-0 = <&sdc_default_state>;
>> pinctrl-names = "default";
>> diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi
>> b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
>> index 062f80798ebb..a32dbdeb5bed 100644
>> --- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
>> @@ -6,8 +6,8 @@
>> * Copyright (c) 2023, Qualcomm Innovation Center, Inc. All rights
>> reserved.
>> */
>> -#include <dt-bindings/interrupt-controller/arm-gic.h>
>> #include <dt-bindings/clock/qcom,ipq9574-gcc.h>
>> +#include <dt-bindings/interrupt-controller/arm-gic.h>
>> #include <dt-bindings/reset/qcom,ipq9574-gcc.h>
>> / {
>> @@ -22,11 +22,41 @@
>> #clock-cells = <0>;
>> };
>> + pcie30_phy0_pipe_clk: pcie30_phy0_pipe_clk {
>> + compatible = "fixed-clock";
>> + clock-frequency = <250000000>;
>> + #clock-cells = <0>;
>> + };
>> +
>> + pcie30_phy1_pipe_clk: pcie30_phy1_pipe_clk {
>> + compatible = "fixed-clock";
>> + clock-frequency = <250000000>;
>> + #clock-cells = <0>;
>> + };
>> +
>> + pcie30_phy2_pipe_clk: pcie30_phy2_pipe_clk {
>> + compatible = "fixed-clock";
>> + clock-frequency = <250000000>;
>> + #clock-cells = <0>;
>> + };
>> +
>> + pcie30_phy3_pipe_clk: pcie30_phy3_pipe_clk {
>> + compatible = "fixed-clock";
>> + clock-frequency = <250000000>;
>> + #clock-cells = <0>;
>> + };
>> +
>> sleep_clk: sleep-clk {
>> compatible = "fixed-clock";
>> #clock-cells = <0>;
>> };
>> + usb3phy_0_cc_pipe_clk: usb3phy_0_cc_pipe_clk {
>> + compatible = "fixed-clock";
>> + clock-frequency = <125000000>;
>> + #clock-cells = <0>;
>> + };
>> +
>
> Why is the usb clock added here ?
As we have brought in the QMP PHY support, added the usb pipe clock too.
Will drop it as it is unrelated to the series.
>
>> xo_board_clk: xo-board-clk {
>> compatible = "fixed-clock";
>> #clock-cells = <0>;
>> @@ -121,6 +151,155 @@
>> #size-cells = <1>;
>> ranges = <0 0 0 0xffffffff>;
>> + pcie0_phy: phy@84000 {
>> + compatible = "qcom,ipq9574-qmp-gen3x1-pcie-phy";
>> + reg = <0x00084000 0x1bc>; /* Serdes PLL */
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges;
>> + clocks = <&gcc GCC_PCIE0_AUX_CLK>,
>> + <&gcc GCC_PCIE0_AHB_CLK>,
>> + <&gcc GCC_ANOC_PCIE0_1LANE_M_CLK>,
>> + <&gcc GCC_SNOC_PCIE0_1LANE_S_CLK>;
>> + clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane";
>> +
>> + assigned-clocks = <&gcc GCC_PCIE0_AUX_CLK>;
>> + assigned-clock-rates = <20000000>;
>> +
>> + resets = <&gcc GCC_PCIE0_PHY_BCR>,
>> + <&gcc GCC_PCIE0PHY_PHY_BCR>;
>> + reset-names = "phy", "common";
>> +
>> + status = "disabled";
>> +
>> + pcie0_lane: phy@84200 {
>> + reg = <0x00084200 0x16c>, /* Serdes Tx */
>> + <0x00084400 0x200>, /* Serdes Rx */
>> + <0x00084800 0x1f0>, /* PCS: Lane0, COM, PCIE */
>> + <0x00084c00 0xf4>; /* pcs_misc */
>> + #phy-cells = <0>;
>> +
>> + clocks = <&gcc GCC_PCIE0_PIPE_CLK>;
>> + clock-names = "pipe0";
>> + clock-output-names = "gcc_pcie0_pipe_clk_src";
>> + #clock-cells = <0>;
>> + };
>> + };
>> +
>> + pcie2_phy: phy@8c000 {
>
> Can the phy/pcie nodes labelled in order ?
> Currently it 0/2/3/1 ?
Sure, okay
>
>> + compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy";
>> + reg = <0x0008c000 0x1bc>; /* Serdes PLL */
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges;
>> +
>> + clocks = <&gcc GCC_PCIE2_AUX_CLK>,
>> + <&gcc GCC_PCIE2_AHB_CLK>,
>> + <&gcc GCC_ANOC_PCIE2_2LANE_M_CLK>,
>> + <&gcc GCC_SNOC_PCIE2_2LANE_S_CLK>;
>> + clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane";
>> +
>> + assigned-clocks = <&gcc GCC_PCIE2_AUX_CLK>;
>> + assigned-clock-rates = <20000000>;
>> +
>> + resets = <&gcc GCC_PCIE2_PHY_BCR>,
>> + <&gcc GCC_PCIE2PHY_PHY_BCR>;
>> + reset-names = "phy", "common";
>> +
>> + status = "disabled";
>> +
>> + pcie2_lanes: phy@8c200 {
>> + reg = <0x0008c200 0x16c>, /* Serdes Tx0 */
>> + <0x0008c400 0x200>, /* Serdes Rx0 */
>> + <0x0008d000 0x1f0>, /* PCS: Lane0, COM, PCIE */
>> + <0x0008c600 0x16c>, /* Serdes Tx1 */
>> + <0x0008c800 0x200>, /* Serdes Rx1 */
>> + <0x0008d400 0x0f8>; /* pcs_misc */
>> +
>> + #phy-cells = <0>;
>> +
>> + clocks = <&gcc GCC_PCIE2_PIPE_CLK>;
>> + clock-names = "pipe0";
>> + clock-output-names = "gcc_pcie2_pipe_clk_src";
>> + #clock-cells = <0>;
>> + };
>> + };
>> +
>> + pcie3_phy: phy@f4000 {
>> + compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy";
>> + reg = <0x000f4000 0x1bc>; /* Serdes PLL */
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges;
>> +
>> + clocks = <&gcc GCC_PCIE3_AUX_CLK>,
>> + <&gcc GCC_PCIE3_AHB_CLK>,
>> + <&gcc GCC_ANOC_PCIE3_2LANE_M_CLK>,
>> + <&gcc GCC_SNOC_PCIE3_2LANE_S_CLK>;
>> + clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane";
>> +
>> + assigned-clocks = <&gcc GCC_PCIE3_AUX_CLK>;
>> + assigned-clock-rates = <20000000>;
>> +
>> + resets = <&gcc GCC_PCIE3_PHY_BCR>,
>> + <&gcc GCC_PCIE3PHY_PHY_BCR>;
>> + reset-names = "phy", "common";
>> +
>> + status = "disabled";
>> +
>> + pcie3_lanes: phy@f4200 {
>> + reg = <0x000f4200 0x16c>, /* Serdes Tx0 */
>> + <0x000f4400 0x200>, /* Serdes Rx0 */
>> + <0x000f5000 0x1f0>, /* PCS: Lane0, COM, PCIE */
>> + <0x000f4600 0x16c>, /* Serdes Tx1 */
>> + <0x000f4800 0x200>, /* Serdes Rx1 */
>> + <0x000f5400 0x0f8>; /* pcs_misc */
>> +
>> + #phy-cells = <0>;
>> +
>> + clocks = <&gcc GCC_PCIE3_PIPE_CLK>;
>> + clock-names = "pipe0";
>> + clock-output-names = "gcc_pcie3_pipe_clk_src";
>> + #clock-cells = <0>;
>> + };
>> + };
>> +
>> + pcie1_phy: phy@fc000 {
>> + compatible = "qcom,ipq9574-qmp-gen3x1-pcie-phy";
>> + reg = <0x000fc000 0x1bc>; /* Serdes PLL */
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges;
>> +
>> + clocks = <&gcc GCC_PCIE1_AUX_CLK>,
>> + <&gcc GCC_PCIE1_AHB_CLK>,
>> + <&gcc GCC_ANOC_PCIE1_1LANE_M_CLK>,
>> + <&gcc GCC_SNOC_PCIE1_1LANE_S_CLK>;
>> + clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane";
>> +
>> + assigned-clocks = <&gcc GCC_PCIE1_AUX_CLK>;
>> + assigned-clock-rates = <20000000>;
>> +
>> + resets = <&gcc GCC_PCIE1_PHY_BCR>,
>> + <&gcc GCC_PCIE1PHY_PHY_BCR>;
>> + reset-names = "phy", "common";
>> +
>> + status = "disabled";
>> +
>> + pcie1_lane: phy@fc200 {
>> + reg = <0x000fc200 0x16c>, /* Serdes Tx */
>> + <0x000fc400 0x200>, /* Serdes Rx */
>> + <0x000fc800 0x1f0>, /* PCS: Lane0, COM, PCIE */
>> + <0x000fcc00 0xf4>; /* pcs_misc */
>> + #phy-cells = <0>;
>> +
>> + clocks = <&gcc GCC_PCIE1_PIPE_CLK>;
>> + clock-names = "pipe0";
>> + clock-output-names = "gcc_pcie1_pipe_clk_src";
>> + #clock-cells = <0>;
>> + };
>> + };
>> +
>> tlmm: pinctrl@1000000 {
>> compatible = "qcom,ipq9574-tlmm";
>> reg = <0x01000000 0x300000>;
>> @@ -145,11 +324,11 @@
>> clocks = <&xo_board_clk>,
>> <&sleep_clk>,
>> <&bias_pll_ubi_nc_clk>,
>> - <0>,
>> - <0>,
>> - <0>,
>> - <0>,
>> - <0>;
>> + <&pcie30_phy0_pipe_clk>,
>> + <&pcie30_phy1_pipe_clk>,
>> + <&pcie30_phy2_pipe_clk>,
>> + <&pcie30_phy3_pipe_clk>,
>> + <&usb3phy_0_cc_pipe_clk>;
>
> Same , why usb3 clk is added here ?
Sure, will drop it
>
> Regards,
> Sricharan
>
Best Regards,
Devi Priya
On 2/14/2023 10:11 PM, Devi Priya wrote:
> Add PCIe0, PCIe1, PCIe2, PCIe3 (and corresponding PHY) devices
> found on IPQ9574 platform. The PCIe0 & PCIe1 are 1-lane Gen3
> host whereas PCIe2 & PCIe3 are 2-lane Gen3 host.
>
> Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
> Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
> Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
> ---
> arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts | 28 ++
> arch/arm64/boot/dts/qcom/ipq9574.dtsi | 477 ++++++++++++++++++-
> 2 files changed, 499 insertions(+), 6 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts b/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
> index 2c8430197ec0..21b53f34ce84 100644
> --- a/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
> +++ b/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
> @@ -8,6 +8,7 @@
>
> /dts-v1/;
>
> +#include <dt-bindings/gpio/gpio.h>
> #include "ipq9574.dtsi"
>
> / {
> @@ -29,6 +30,33 @@
> status = "okay";
> };
>
> +&pcie1_phy {
> + status = "okay";
> +};
> +
> +&pcie1_x1 {
> + perst-gpios = <&tlmm 26 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
> +
> +&pcie2_phy {
> + status = "okay";
> +};
> +
> +&pcie2_x2 {
> + perst-gpios = <&tlmm 29 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
> +
> +&pcie3_phy {
> + status = "okay";
> +};
> +
> +&pcie3_x2 {
> + perst-gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
> +
> &sdhc_1 {
> pinctrl-0 = <&sdc_default_state>;
> pinctrl-names = "default";
> diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> index 062f80798ebb..a32dbdeb5bed 100644
> --- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> +++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> @@ -6,8 +6,8 @@
> * Copyright (c) 2023, Qualcomm Innovation Center, Inc. All rights reserved.
> */
>
> -#include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/clock/qcom,ipq9574-gcc.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/reset/qcom,ipq9574-gcc.h>
>
> / {
> @@ -22,11 +22,41 @@
> #clock-cells = <0>;
> };
>
> + pcie30_phy0_pipe_clk: pcie30_phy0_pipe_clk {
> + compatible = "fixed-clock";
> + clock-frequency = <250000000>;
> + #clock-cells = <0>;
> + };
> +
> + pcie30_phy1_pipe_clk: pcie30_phy1_pipe_clk {
> + compatible = "fixed-clock";
> + clock-frequency = <250000000>;
> + #clock-cells = <0>;
> + };
> +
> + pcie30_phy2_pipe_clk: pcie30_phy2_pipe_clk {
> + compatible = "fixed-clock";
> + clock-frequency = <250000000>;
> + #clock-cells = <0>;
> + };
> +
> + pcie30_phy3_pipe_clk: pcie30_phy3_pipe_clk {
> + compatible = "fixed-clock";
> + clock-frequency = <250000000>;
> + #clock-cells = <0>;
> + };
> +
> sleep_clk: sleep-clk {
> compatible = "fixed-clock";
> #clock-cells = <0>;
> };
>
> + usb3phy_0_cc_pipe_clk: usb3phy_0_cc_pipe_clk {
> + compatible = "fixed-clock";
> + clock-frequency = <125000000>;
> + #clock-cells = <0>;
> + };
> +
> xo_board_clk: xo-board-clk {
> compatible = "fixed-clock";
> #clock-cells = <0>;
> @@ -121,6 +151,155 @@
> #size-cells = <1>;
> ranges = <0 0 0 0xffffffff>;
>
> + pcie0_phy: phy@84000 {
> + compatible = "qcom,ipq9574-qmp-gen3x1-pcie-phy";
> + reg = <0x00084000 0x1bc>; /* Serdes PLL */
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> + clocks = <&gcc GCC_PCIE0_AUX_CLK>,
> + <&gcc GCC_PCIE0_AHB_CLK>,
> + <&gcc GCC_ANOC_PCIE0_1LANE_M_CLK>,
> + <&gcc GCC_SNOC_PCIE0_1LANE_S_CLK>;
> + clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane";
> +
> + assigned-clocks = <&gcc GCC_PCIE0_AUX_CLK>;
> + assigned-clock-rates = <20000000>;
> +
> + resets = <&gcc GCC_PCIE0_PHY_BCR>,
> + <&gcc GCC_PCIE0PHY_PHY_BCR>;
> + reset-names = "phy", "common";
> +
> + status = "disabled";
> +
> + pcie0_lane: phy@84200 {
> + reg = <0x00084200 0x16c>, /* Serdes Tx */
> + <0x00084400 0x200>, /* Serdes Rx */
> + <0x00084800 0x1f0>, /* PCS: Lane0, COM, PCIE */
> + <0x00084c00 0xf4>; /* pcs_misc */
> + #phy-cells = <0>;
> +
> + clocks = <&gcc GCC_PCIE0_PIPE_CLK>;
> + clock-names = "pipe0";
> + clock-output-names = "gcc_pcie0_pipe_clk_src";
> + #clock-cells = <0>;
> + };
> + };
> +
> + pcie2_phy: phy@8c000 {
> + compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy";
> + reg = <0x0008c000 0x1bc>; /* Serdes PLL */
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + clocks = <&gcc GCC_PCIE2_AUX_CLK>,
> + <&gcc GCC_PCIE2_AHB_CLK>,
> + <&gcc GCC_ANOC_PCIE2_2LANE_M_CLK>,
> + <&gcc GCC_SNOC_PCIE2_2LANE_S_CLK>;
> + clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane";
> +
> + assigned-clocks = <&gcc GCC_PCIE2_AUX_CLK>;
> + assigned-clock-rates = <20000000>;
> +
> + resets = <&gcc GCC_PCIE2_PHY_BCR>,
> + <&gcc GCC_PCIE2PHY_PHY_BCR>;
> + reset-names = "phy", "common";
> +
> + status = "disabled";
> +
> + pcie2_lanes: phy@8c200 {
> + reg = <0x0008c200 0x16c>, /* Serdes Tx0 */
> + <0x0008c400 0x200>, /* Serdes Rx0 */
> + <0x0008d000 0x1f0>, /* PCS: Lane0, COM, PCIE */
> + <0x0008c600 0x16c>, /* Serdes Tx1 */
> + <0x0008c800 0x200>, /* Serdes Rx1 */
> + <0x0008d400 0x0f8>; /* pcs_misc */
> +
> + #phy-cells = <0>;
> +
> + clocks = <&gcc GCC_PCIE2_PIPE_CLK>;
> + clock-names = "pipe0";
> + clock-output-names = "gcc_pcie2_pipe_clk_src";
> + #clock-cells = <0>;
> + };
> + };
> +
> + pcie3_phy: phy@f4000 {
> + compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy";
> + reg = <0x000f4000 0x1bc>; /* Serdes PLL */
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + clocks = <&gcc GCC_PCIE3_AUX_CLK>,
> + <&gcc GCC_PCIE3_AHB_CLK>,
> + <&gcc GCC_ANOC_PCIE3_2LANE_M_CLK>,
> + <&gcc GCC_SNOC_PCIE3_2LANE_S_CLK>;
> + clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane";
> +
> + assigned-clocks = <&gcc GCC_PCIE3_AUX_CLK>;
> + assigned-clock-rates = <20000000>;
> +
> + resets = <&gcc GCC_PCIE3_PHY_BCR>,
> + <&gcc GCC_PCIE3PHY_PHY_BCR>;
> + reset-names = "phy", "common";
> +
> + status = "disabled";
> +
> + pcie3_lanes: phy@f4200 {
> + reg = <0x000f4200 0x16c>, /* Serdes Tx0 */
> + <0x000f4400 0x200>, /* Serdes Rx0 */
> + <0x000f5000 0x1f0>, /* PCS: Lane0, COM, PCIE */
> + <0x000f4600 0x16c>, /* Serdes Tx1 */
> + <0x000f4800 0x200>, /* Serdes Rx1 */
> + <0x000f5400 0x0f8>; /* pcs_misc */
> +
> + #phy-cells = <0>;
> +
> + clocks = <&gcc GCC_PCIE3_PIPE_CLK>;
> + clock-names = "pipe0";
> + clock-output-names = "gcc_pcie3_pipe_clk_src";
> + #clock-cells = <0>;
> + };
> + };
> +
> + pcie1_phy: phy@fc000 {
> + compatible = "qcom,ipq9574-qmp-gen3x1-pcie-phy";
> + reg = <0x000fc000 0x1bc>; /* Serdes PLL */
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + clocks = <&gcc GCC_PCIE1_AUX_CLK>,
> + <&gcc GCC_PCIE1_AHB_CLK>,
> + <&gcc GCC_ANOC_PCIE1_1LANE_M_CLK>,
> + <&gcc GCC_SNOC_PCIE1_1LANE_S_CLK>;
> + clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane";
> +
> + assigned-clocks = <&gcc GCC_PCIE1_AUX_CLK>;
> + assigned-clock-rates = <20000000>;
> +
> + resets = <&gcc GCC_PCIE1_PHY_BCR>,
> + <&gcc GCC_PCIE1PHY_PHY_BCR>;
> + reset-names = "phy", "common";
> +
> + status = "disabled";
> +
> + pcie1_lane: phy@fc200 {
> + reg = <0x000fc200 0x16c>, /* Serdes Tx */
> + <0x000fc400 0x200>, /* Serdes Rx */
> + <0x000fc800 0x1f0>, /* PCS: Lane0, COM, PCIE */
> + <0x000fcc00 0xf4>; /* pcs_misc */
> + #phy-cells = <0>;
> +
> + clocks = <&gcc GCC_PCIE1_PIPE_CLK>;
> + clock-names = "pipe0";
> + clock-output-names = "gcc_pcie1_pipe_clk_src";
> + #clock-cells = <0>;
> + };
> + };
> +
> tlmm: pinctrl@1000000 {
> compatible = "qcom,ipq9574-tlmm";
> reg = <0x01000000 0x300000>;
> @@ -145,11 +324,11 @@
> clocks = <&xo_board_clk>,
> <&sleep_clk>,
> <&bias_pll_ubi_nc_clk>,
> - <0>,
> - <0>,
> - <0>,
> - <0>,
> - <0>;
> + <&pcie30_phy0_pipe_clk>,
> + <&pcie30_phy1_pipe_clk>,
> + <&pcie30_phy2_pipe_clk>,
> + <&pcie30_phy3_pipe_clk>,
> + <&usb3phy_0_cc_pipe_clk>;
pipe clock source is PHY. So should we add the pcie_phy phandle here and
use it like how it is done in other targets, ex: sm8550.dtsi?
> #clock-cells = <1>;
> #reset-cells = <1>;
> #power-domain-cells = <1>;
> @@ -282,6 +461,292 @@
> status = "disabled";
> };
> };
> +
> + pcie1_x1: pci@10000000 {
> + compatible = "qcom,pcie-ipq9574";
> + reg = <0x10000000 0xf1d>,
> + <0x10000F20 0xa8>,
> + <0x10001000 0x1000>,
> + <0x000F8000 0x4000>,
> + <0x10100000 0x1000>,
> + <0x00618108 0x4>;
> + reg-names = "dbi", "elbi", "atu", "parf", "config", "aggr_noc";
> + device_type = "pci";
> + linux,pci-domain = <2>;
> + bus-range = <0x00 0xff>;
> + num-lanes = <1>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> +
> + ranges = <0x81000000 0 0x10200000 0x10200000
> + 0 0x00100000 /* downstream I/O */
> + 0x82000000 0 0x10300000 0x10300000
> + 0 0x07d00000>; /* non-prefetchable memory */
> +
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0 0 0 0x7>;
> + interrupt-map = <0 0 0 1 &intc 0 35
> + IRQ_TYPE_LEVEL_HIGH>, /* int_a */
> + <0 0 0 2 &intc 0 49
> + IRQ_TYPE_LEVEL_HIGH>, /* int_b */
> + <0 0 0 3 &intc 0 84
> + IRQ_TYPE_LEVEL_HIGH>, /* int_c */
> + <0 0 0 4 &intc 0 85
> + IRQ_TYPE_LEVEL_HIGH>; /* int_d */
> +
> + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "global_irq";
Controller driver doesn't support the "global_irq" yet. Please correct
me If I am wrong.
Thanks, Kathiravan T.
On Tue, Feb 14, 2023 at 10:11:35PM +0530, Devi Priya wrote:
> Add PCIe0, PCIe1, PCIe2, PCIe3 (and corresponding PHY) devices
> found on IPQ9574 platform. The PCIe0 & PCIe1 are 1-lane Gen3
> host whereas PCIe2 & PCIe3 are 2-lane Gen3 host.
>
Please split the board devicetree changes into a separate patch.
> Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
> Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
> Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
> ---
> arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts | 28 ++
> arch/arm64/boot/dts/qcom/ipq9574.dtsi | 477 ++++++++++++++++++-
> 2 files changed, 499 insertions(+), 6 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts b/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
> index 2c8430197ec0..21b53f34ce84 100644
> --- a/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
> +++ b/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
> @@ -8,6 +8,7 @@
>
> /dts-v1/;
>
> +#include <dt-bindings/gpio/gpio.h>
> #include "ipq9574.dtsi"
>
> / {
> @@ -29,6 +30,33 @@
> status = "okay";
> };
>
> +&pcie1_phy {
> + status = "okay";
No PHY power supply needed? Same comment for rest of the PHY nodes.
> +};
> +
> +&pcie1_x1 {
No need to add a suffix to node label indicating the lane config.
> + perst-gpios = <&tlmm 26 GPIO_ACTIVE_LOW>;
What about "wake" pin? Don't you need pinctrl definitions for these GPIOs?
Same comment for rest of the PCIe nodes.
> + status = "okay";
> +};
> +
> +&pcie2_phy {
> + status = "okay";
> +};
> +
> +&pcie2_x2 {
> + perst-gpios = <&tlmm 29 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
> +
> +&pcie3_phy {
> + status = "okay";
> +};
> +
> +&pcie3_x2 {
> + perst-gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
> +
> &sdhc_1 {
> pinctrl-0 = <&sdc_default_state>;
> pinctrl-names = "default";
> diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> index 062f80798ebb..a32dbdeb5bed 100644
> --- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> +++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> @@ -6,8 +6,8 @@
> * Copyright (c) 2023, Qualcomm Innovation Center, Inc. All rights reserved.
> */
>
> -#include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/clock/qcom,ipq9574-gcc.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/reset/qcom,ipq9574-gcc.h>
>
> / {
> @@ -22,11 +22,41 @@
> #clock-cells = <0>;
> };
>
> + pcie30_phy0_pipe_clk: pcie30_phy0_pipe_clk {
> + compatible = "fixed-clock";
> + clock-frequency = <250000000>;
> + #clock-cells = <0>;
> + };
> +
> + pcie30_phy1_pipe_clk: pcie30_phy1_pipe_clk {
> + compatible = "fixed-clock";
> + clock-frequency = <250000000>;
> + #clock-cells = <0>;
> + };
> +
> + pcie30_phy2_pipe_clk: pcie30_phy2_pipe_clk {
> + compatible = "fixed-clock";
> + clock-frequency = <250000000>;
> + #clock-cells = <0>;
> + };
> +
> + pcie30_phy3_pipe_clk: pcie30_phy3_pipe_clk {
> + compatible = "fixed-clock";
> + clock-frequency = <250000000>;
> + #clock-cells = <0>;
> + };
Why PIPE clocks are modeled as fixed clocks unlike other SoCs?
> +
> sleep_clk: sleep-clk {
> compatible = "fixed-clock";
> #clock-cells = <0>;
> };
>
> + usb3phy_0_cc_pipe_clk: usb3phy_0_cc_pipe_clk {
> + compatible = "fixed-clock";
> + clock-frequency = <125000000>;
> + #clock-cells = <0>;
> + };
Spurious?
> +
> xo_board_clk: xo-board-clk {
> compatible = "fixed-clock";
> #clock-cells = <0>;
> @@ -121,6 +151,155 @@
> #size-cells = <1>;
> ranges = <0 0 0 0xffffffff>;
>
> + pcie0_phy: phy@84000 {
> + compatible = "qcom,ipq9574-qmp-gen3x1-pcie-phy";
> + reg = <0x00084000 0x1bc>; /* Serdes PLL */
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> + clocks = <&gcc GCC_PCIE0_AUX_CLK>,
> + <&gcc GCC_PCIE0_AHB_CLK>,
> + <&gcc GCC_ANOC_PCIE0_1LANE_M_CLK>,
> + <&gcc GCC_SNOC_PCIE0_1LANE_S_CLK>;
> + clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane";
Care to explain what these anoc_lane and snoc_lane clocks are?
> +
> + assigned-clocks = <&gcc GCC_PCIE0_AUX_CLK>;
> + assigned-clock-rates = <20000000>;
> +
> + resets = <&gcc GCC_PCIE0_PHY_BCR>,
> + <&gcc GCC_PCIE0PHY_PHY_BCR>;
> + reset-names = "phy", "common";
> +
> + status = "disabled";
> +
> + pcie0_lane: phy@84200 {
> + reg = <0x00084200 0x16c>, /* Serdes Tx */
> + <0x00084400 0x200>, /* Serdes Rx */
> + <0x00084800 0x1f0>, /* PCS: Lane0, COM, PCIE */
> + <0x00084c00 0xf4>; /* pcs_misc */
> + #phy-cells = <0>;
> +
> + clocks = <&gcc GCC_PCIE0_PIPE_CLK>;
> + clock-names = "pipe0";
> + clock-output-names = "gcc_pcie0_pipe_clk_src";
> + #clock-cells = <0>;
> + };
> + };
> +
[...]
> + pcie1_x1: pci@10000000 {
> + compatible = "qcom,pcie-ipq9574";
> + reg = <0x10000000 0xf1d>,
> + <0x10000F20 0xa8>,
> + <0x10001000 0x1000>,
> + <0x000F8000 0x4000>,
> + <0x10100000 0x1000>,
> + <0x00618108 0x4>;
> + reg-names = "dbi", "elbi", "atu", "parf", "config", "aggr_noc";
As I asked in the binding patch, why "aggr_noc" region is required?
> + device_type = "pci";
> + linux,pci-domain = <2>;
> + bus-range = <0x00 0xff>;
> + num-lanes = <1>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> +
> + ranges = <0x81000000 0 0x10200000 0x10200000
> + 0 0x00100000 /* downstream I/O */
> + 0x82000000 0 0x10300000 0x10300000
> + 0 0x07d00000>; /* non-prefetchable memory */
Don't split the ranges and encode them in a single line.
Also, the I'm not sure why you have set the relocatable flag (n) for both
ranges i.e., in 0x81000000 and 0x82000000.
> +
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0 0 0 0x7>;
> + interrupt-map = <0 0 0 1 &intc 0 35
> + IRQ_TYPE_LEVEL_HIGH>, /* int_a */
> + <0 0 0 2 &intc 0 49
> + IRQ_TYPE_LEVEL_HIGH>, /* int_b */
> + <0 0 0 3 &intc 0 84
> + IRQ_TYPE_LEVEL_HIGH>, /* int_c */
> + <0 0 0 4 &intc 0 85
> + IRQ_TYPE_LEVEL_HIGH>; /* int_d */
> +
Again, wrap the interrupts in a single line.
> + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "global_irq";
> +
Linux doesn't support global_irq yet. But since devicetree is supposed to
describe the hardware, you can keep it.
Above comment applies to rest of the PCIe nodes.
> + /* clocks and clock-names are used to enable the clock in CBCR */
> + clocks = <&gcc GCC_PCIE1_AHB_CLK>,
> + <&gcc GCC_PCIE1_AUX_CLK>,
> + <&gcc GCC_PCIE1_AXI_M_CLK>,
> + <&gcc GCC_PCIE1_AXI_S_CLK>,
> + <&gcc GCC_PCIE1_AXI_S_BRIDGE_CLK>,
> + <&gcc GCC_PCIE1_RCHNG_CLK>;
> + clock-names = "ahb",
> + "aux",
> + "axi_m",
> + "axi_s",
> + "axi_bridge",
> + "rchng";
> +
> + resets = <&gcc GCC_PCIE1_PIPE_ARES>,
> + <&gcc GCC_PCIE1_CORE_STICKY_ARES>,
> + <&gcc GCC_PCIE1_AXI_S_STICKY_ARES>,
> + <&gcc GCC_PCIE1_AXI_S_ARES>,
> + <&gcc GCC_PCIE1_AXI_M_STICKY_ARES>,
> + <&gcc GCC_PCIE1_AXI_M_ARES>,
> + <&gcc GCC_PCIE1_AUX_ARES>,
> + <&gcc GCC_PCIE1_AHB_ARES>;
> + reset-names = "pipe",
> + "sticky",
> + "axi_s_sticky",
> + "axi_s",
> + "axi_m_sticky",
> + "axi_m",
> + "aux",
> + "ahb";
> +
> + phys = <&pcie1_lane>;
> + phy-names = "pciephy";
> + msi-parent = <&v2m0>;
> + status = "disabled";
> + };
> +
[...]
> + pcie2_x2: pci@20000000 {
> + compatible = "qcom,pcie-ipq9574";
> + reg = <0x20000000 0xf1d>,
> + <0x20000F20 0xa8>,
> + <0x20001000 0x1000>,
> + <0x00088000 0x4000>,
> + <0x20100000 0x1000>;
> + reg-names = "dbi", "elbi", "atu", "parf", "config";
> + device_type = "pci";
> + linux,pci-domain = <3>;
> + bus-range = <0x00 0xff>;
> + num-lanes =<2>;
Space after =
Thanks,
Mani
On 2/24/2023 12:27 PM, Kathiravan T wrote:
>
> On 2/14/2023 10:11 PM, Devi Priya wrote:
>> Add PCIe0, PCIe1, PCIe2, PCIe3 (and corresponding PHY) devices
>> found on IPQ9574 platform. The PCIe0 & PCIe1 are 1-lane Gen3
>> host whereas PCIe2 & PCIe3 are 2-lane Gen3 host.
>>
>> Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
>> Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
>> Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
>> ---
>> arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts | 28 ++
>> arch/arm64/boot/dts/qcom/ipq9574.dtsi | 477 ++++++++++++++++++-
>> 2 files changed, 499 insertions(+), 6 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
>> b/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
>> index 2c8430197ec0..21b53f34ce84 100644
>> --- a/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
>> +++ b/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
>> @@ -8,6 +8,7 @@
>> /dts-v1/;
>> +#include <dt-bindings/gpio/gpio.h>
>> #include "ipq9574.dtsi"
>> / {
>> @@ -29,6 +30,33 @@
>> status = "okay";
>> };
>> +&pcie1_phy {
>> + status = "okay";
>> +};
>> +
>> +&pcie1_x1 {
>> + perst-gpios = <&tlmm 26 GPIO_ACTIVE_LOW>;
>> + status = "okay";
>> +};
>> +
>> +&pcie2_phy {
>> + status = "okay";
>> +};
>> +
>> +&pcie2_x2 {
>> + perst-gpios = <&tlmm 29 GPIO_ACTIVE_LOW>;
>> + status = "okay";
>> +};
>> +
>> +&pcie3_phy {
>> + status = "okay";
>> +};
>> +
>> +&pcie3_x2 {
>> + perst-gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
>> + status = "okay";
>> +};
>> +
>> &sdhc_1 {
>> pinctrl-0 = <&sdc_default_state>;
>> pinctrl-names = "default";
>> diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi
>> b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
>> index 062f80798ebb..a32dbdeb5bed 100644
>> --- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
>> @@ -6,8 +6,8 @@
>> * Copyright (c) 2023, Qualcomm Innovation Center, Inc. All rights
>> reserved.
>> */
>> -#include <dt-bindings/interrupt-controller/arm-gic.h>
>> #include <dt-bindings/clock/qcom,ipq9574-gcc.h>
>> +#include <dt-bindings/interrupt-controller/arm-gic.h>
>> #include <dt-bindings/reset/qcom,ipq9574-gcc.h>
>> / {
>> @@ -22,11 +22,41 @@
>> #clock-cells = <0>;
>> };
>> + pcie30_phy0_pipe_clk: pcie30_phy0_pipe_clk {
>> + compatible = "fixed-clock";
>> + clock-frequency = <250000000>;
>> + #clock-cells = <0>;
>> + };
>> +
>> + pcie30_phy1_pipe_clk: pcie30_phy1_pipe_clk {
>> + compatible = "fixed-clock";
>> + clock-frequency = <250000000>;
>> + #clock-cells = <0>;
>> + };
>> +
>> + pcie30_phy2_pipe_clk: pcie30_phy2_pipe_clk {
>> + compatible = "fixed-clock";
>> + clock-frequency = <250000000>;
>> + #clock-cells = <0>;
>> + };
>> +
>> + pcie30_phy3_pipe_clk: pcie30_phy3_pipe_clk {
>> + compatible = "fixed-clock";
>> + clock-frequency = <250000000>;
>> + #clock-cells = <0>;
>> + };
>> +
>> sleep_clk: sleep-clk {
>> compatible = "fixed-clock";
>> #clock-cells = <0>;
>> };
>> + usb3phy_0_cc_pipe_clk: usb3phy_0_cc_pipe_clk {
>> + compatible = "fixed-clock";
>> + clock-frequency = <125000000>;
>> + #clock-cells = <0>;
>> + };
>> +
>> xo_board_clk: xo-board-clk {
>> compatible = "fixed-clock";
>> #clock-cells = <0>;
>> @@ -121,6 +151,155 @@
>> #size-cells = <1>;
>> ranges = <0 0 0 0xffffffff>;
>> + pcie0_phy: phy@84000 {
>> + compatible = "qcom,ipq9574-qmp-gen3x1-pcie-phy";
>> + reg = <0x00084000 0x1bc>; /* Serdes PLL */
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges;
>> + clocks = <&gcc GCC_PCIE0_AUX_CLK>,
>> + <&gcc GCC_PCIE0_AHB_CLK>,
>> + <&gcc GCC_ANOC_PCIE0_1LANE_M_CLK>,
>> + <&gcc GCC_SNOC_PCIE0_1LANE_S_CLK>;
>> + clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane";
>> +
>> + assigned-clocks = <&gcc GCC_PCIE0_AUX_CLK>;
>> + assigned-clock-rates = <20000000>;
>> +
>> + resets = <&gcc GCC_PCIE0_PHY_BCR>,
>> + <&gcc GCC_PCIE0PHY_PHY_BCR>;
>> + reset-names = "phy", "common";
>> +
>> + status = "disabled";
>> +
>> + pcie0_lane: phy@84200 {
>> + reg = <0x00084200 0x16c>, /* Serdes Tx */
>> + <0x00084400 0x200>, /* Serdes Rx */
>> + <0x00084800 0x1f0>, /* PCS: Lane0, COM, PCIE */
>> + <0x00084c00 0xf4>; /* pcs_misc */
>> + #phy-cells = <0>;
>> +
>> + clocks = <&gcc GCC_PCIE0_PIPE_CLK>;
>> + clock-names = "pipe0";
>> + clock-output-names = "gcc_pcie0_pipe_clk_src";
>> + #clock-cells = <0>;
>> + };
>> + };
>> +
>> + pcie2_phy: phy@8c000 {
>> + compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy";
>> + reg = <0x0008c000 0x1bc>; /* Serdes PLL */
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges;
>> +
>> + clocks = <&gcc GCC_PCIE2_AUX_CLK>,
>> + <&gcc GCC_PCIE2_AHB_CLK>,
>> + <&gcc GCC_ANOC_PCIE2_2LANE_M_CLK>,
>> + <&gcc GCC_SNOC_PCIE2_2LANE_S_CLK>;
>> + clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane";
>> +
>> + assigned-clocks = <&gcc GCC_PCIE2_AUX_CLK>;
>> + assigned-clock-rates = <20000000>;
>> +
>> + resets = <&gcc GCC_PCIE2_PHY_BCR>,
>> + <&gcc GCC_PCIE2PHY_PHY_BCR>;
>> + reset-names = "phy", "common";
>> +
>> + status = "disabled";
>> +
>> + pcie2_lanes: phy@8c200 {
>> + reg = <0x0008c200 0x16c>, /* Serdes Tx0 */
>> + <0x0008c400 0x200>, /* Serdes Rx0 */
>> + <0x0008d000 0x1f0>, /* PCS: Lane0, COM, PCIE */
>> + <0x0008c600 0x16c>, /* Serdes Tx1 */
>> + <0x0008c800 0x200>, /* Serdes Rx1 */
>> + <0x0008d400 0x0f8>; /* pcs_misc */
>> +
>> + #phy-cells = <0>;
>> +
>> + clocks = <&gcc GCC_PCIE2_PIPE_CLK>;
>> + clock-names = "pipe0";
>> + clock-output-names = "gcc_pcie2_pipe_clk_src";
>> + #clock-cells = <0>;
>> + };
>> + };
>> +
>> + pcie3_phy: phy@f4000 {
>> + compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy";
>> + reg = <0x000f4000 0x1bc>; /* Serdes PLL */
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges;
>> +
>> + clocks = <&gcc GCC_PCIE3_AUX_CLK>,
>> + <&gcc GCC_PCIE3_AHB_CLK>,
>> + <&gcc GCC_ANOC_PCIE3_2LANE_M_CLK>,
>> + <&gcc GCC_SNOC_PCIE3_2LANE_S_CLK>;
>> + clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane";
>> +
>> + assigned-clocks = <&gcc GCC_PCIE3_AUX_CLK>;
>> + assigned-clock-rates = <20000000>;
>> +
>> + resets = <&gcc GCC_PCIE3_PHY_BCR>,
>> + <&gcc GCC_PCIE3PHY_PHY_BCR>;
>> + reset-names = "phy", "common";
>> +
>> + status = "disabled";
>> +
>> + pcie3_lanes: phy@f4200 {
>> + reg = <0x000f4200 0x16c>, /* Serdes Tx0 */
>> + <0x000f4400 0x200>, /* Serdes Rx0 */
>> + <0x000f5000 0x1f0>, /* PCS: Lane0, COM, PCIE */
>> + <0x000f4600 0x16c>, /* Serdes Tx1 */
>> + <0x000f4800 0x200>, /* Serdes Rx1 */
>> + <0x000f5400 0x0f8>; /* pcs_misc */
>> +
>> + #phy-cells = <0>;
>> +
>> + clocks = <&gcc GCC_PCIE3_PIPE_CLK>;
>> + clock-names = "pipe0";
>> + clock-output-names = "gcc_pcie3_pipe_clk_src";
>> + #clock-cells = <0>;
>> + };
>> + };
>> +
>> + pcie1_phy: phy@fc000 {
>> + compatible = "qcom,ipq9574-qmp-gen3x1-pcie-phy";
>> + reg = <0x000fc000 0x1bc>; /* Serdes PLL */
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges;
>> +
>> + clocks = <&gcc GCC_PCIE1_AUX_CLK>,
>> + <&gcc GCC_PCIE1_AHB_CLK>,
>> + <&gcc GCC_ANOC_PCIE1_1LANE_M_CLK>,
>> + <&gcc GCC_SNOC_PCIE1_1LANE_S_CLK>;
>> + clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane";
>> +
>> + assigned-clocks = <&gcc GCC_PCIE1_AUX_CLK>;
>> + assigned-clock-rates = <20000000>;
>> +
>> + resets = <&gcc GCC_PCIE1_PHY_BCR>,
>> + <&gcc GCC_PCIE1PHY_PHY_BCR>;
>> + reset-names = "phy", "common";
>> +
>> + status = "disabled";
>> +
>> + pcie1_lane: phy@fc200 {
>> + reg = <0x000fc200 0x16c>, /* Serdes Tx */
>> + <0x000fc400 0x200>, /* Serdes Rx */
>> + <0x000fc800 0x1f0>, /* PCS: Lane0, COM, PCIE */
>> + <0x000fcc00 0xf4>; /* pcs_misc */
>> + #phy-cells = <0>;
>> +
>> + clocks = <&gcc GCC_PCIE1_PIPE_CLK>;
>> + clock-names = "pipe0";
>> + clock-output-names = "gcc_pcie1_pipe_clk_src";
>> + #clock-cells = <0>;
>> + };
>> + };
>> +
>> tlmm: pinctrl@1000000 {
>> compatible = "qcom,ipq9574-tlmm";
>> reg = <0x01000000 0x300000>;
>> @@ -145,11 +324,11 @@
>> clocks = <&xo_board_clk>,
>> <&sleep_clk>,
>> <&bias_pll_ubi_nc_clk>,
>> - <0>,
>> - <0>,
>> - <0>,
>> - <0>,
>> - <0>;
>> + <&pcie30_phy0_pipe_clk>,
>> + <&pcie30_phy1_pipe_clk>,
>> + <&pcie30_phy2_pipe_clk>,
>> + <&pcie30_phy3_pipe_clk>,
>> + <&usb3phy_0_cc_pipe_clk>;
>
>
> pipe clock source is PHY. So should we add the pcie_phy phandle here and
> use it like how it is done in other targets, ex: sm8550.dtsi?
Yes sure kathir. Will update this in the next series
>
>
>> #clock-cells = <1>;
>> #reset-cells = <1>;
>> #power-domain-cells = <1>;
>> @@ -282,6 +461,292 @@
>> status = "disabled";
>> };
>> };
>> +
>> + pcie1_x1: pci@10000000 {
>> + compatible = "qcom,pcie-ipq9574";
>> + reg = <0x10000000 0xf1d>,
>> + <0x10000F20 0xa8>,
>> + <0x10001000 0x1000>,
>> + <0x000F8000 0x4000>,
>> + <0x10100000 0x1000>,
>> + <0x00618108 0x4>;
>> + reg-names = "dbi", "elbi", "atu", "parf", "config",
>> "aggr_noc";
>> + device_type = "pci";
>> + linux,pci-domain = <2>;
>> + bus-range = <0x00 0xff>;
>> + num-lanes = <1>;
>> + #address-cells = <3>;
>> + #size-cells = <2>;
>> +
>> + ranges = <0x81000000 0 0x10200000 0x10200000
>> + 0 0x00100000 /* downstream I/O */
>> + 0x82000000 0 0x10300000 0x10300000
>> + 0 0x07d00000>; /* non-prefetchable memory */
>> +
>> + #interrupt-cells = <1>;
>> + interrupt-map-mask = <0 0 0 0x7>;
>> + interrupt-map = <0 0 0 1 &intc 0 35
>> + IRQ_TYPE_LEVEL_HIGH>, /* int_a */
>> + <0 0 0 2 &intc 0 49
>> + IRQ_TYPE_LEVEL_HIGH>, /* int_b */
>> + <0 0 0 3 &intc 0 84
>> + IRQ_TYPE_LEVEL_HIGH>, /* int_c */
>> + <0 0 0 4 &intc 0 85
>> + IRQ_TYPE_LEVEL_HIGH>; /* int_d */
>> +
>> + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
>> + interrupt-names = "global_irq";
>
>
> Controller driver doesn't support the "global_irq" yet. Please correct
> me If I am wrong.
>
>
> Thanks, Kathiravan T.
>
Regards,
Devi Priya
On 2/24/2023 2:29 PM, Manivannan Sadhasivam wrote:
> On Tue, Feb 14, 2023 at 10:11:35PM +0530, Devi Priya wrote:
>> Add PCIe0, PCIe1, PCIe2, PCIe3 (and corresponding PHY) devices
>> found on IPQ9574 platform. The PCIe0 & PCIe1 are 1-lane Gen3
>> host whereas PCIe2 & PCIe3 are 2-lane Gen3 host.
>>
>
> Please split the board devicetree changes into a separate patch.
Sure, okay
>
>> Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
>> Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
>> Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
>> ---
>> arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts | 28 ++
>> arch/arm64/boot/dts/qcom/ipq9574.dtsi | 477 ++++++++++++++++++-
>> 2 files changed, 499 insertions(+), 6 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts b/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
>> index 2c8430197ec0..21b53f34ce84 100644
>> --- a/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
>> +++ b/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
>> @@ -8,6 +8,7 @@
>>
>> /dts-v1/;
>>
>> +#include <dt-bindings/gpio/gpio.h>
>> #include "ipq9574.dtsi"
>>
>> / {
>> @@ -29,6 +30,33 @@
>> status = "okay";
>> };
>>
>> +&pcie1_phy {
>> + status = "okay";
>
> No PHY power supply needed? Same comment for rest of the PHY nodes.
The PHY power supplies (VDDA_0P9 and VDDA_1P8) would be turned 'on'
by default and so no supply is added here
>
>> +};
>> +
>> +&pcie1_x1 {
>
> No need to add a suffix to node label indicating the lane config.
Okay
>
>> + perst-gpios = <&tlmm 26 GPIO_ACTIVE_LOW>;
>
> What about "wake" pin? Don't you need pinctrl definitions for these GPIOs?
> Same comment for rest of the PCIe nodes.
In IPQ9574, Wake pin isn't required as the slave devices are not
hot-pluggable & they get enumerated during the bootup. Will add the
pinctrl definition for the Perst gpio in V2
>
>> + status = "okay";
>> +};
>> +
>> +&pcie2_phy {
>> + status = "okay";
>> +};
>> +
>> +&pcie2_x2 {
>> + perst-gpios = <&tlmm 29 GPIO_ACTIVE_LOW>;
>> + status = "okay";
>> +};
>> +
>> +&pcie3_phy {
>> + status = "okay";
>> +};
>> +
>> +&pcie3_x2 {
>> + perst-gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
>> + status = "okay";
>> +};
>> +
>> &sdhc_1 {
>> pinctrl-0 = <&sdc_default_state>;
>> pinctrl-names = "default";
>> diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
>> index 062f80798ebb..a32dbdeb5bed 100644
>> --- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
>> @@ -6,8 +6,8 @@
>> * Copyright (c) 2023, Qualcomm Innovation Center, Inc. All rights reserved.
>> */
>>
>> -#include <dt-bindings/interrupt-controller/arm-gic.h>
>> #include <dt-bindings/clock/qcom,ipq9574-gcc.h>
>> +#include <dt-bindings/interrupt-controller/arm-gic.h>
>> #include <dt-bindings/reset/qcom,ipq9574-gcc.h>
>>
>> / {
>> @@ -22,11 +22,41 @@
>> #clock-cells = <0>;
>> };
>>
>> + pcie30_phy0_pipe_clk: pcie30_phy0_pipe_clk {
>> + compatible = "fixed-clock";
>> + clock-frequency = <250000000>;
>> + #clock-cells = <0>;
>> + };
>> +
>> + pcie30_phy1_pipe_clk: pcie30_phy1_pipe_clk {
>> + compatible = "fixed-clock";
>> + clock-frequency = <250000000>;
>> + #clock-cells = <0>;
>> + };
>> +
>> + pcie30_phy2_pipe_clk: pcie30_phy2_pipe_clk {
>> + compatible = "fixed-clock";
>> + clock-frequency = <250000000>;
>> + #clock-cells = <0>;
>> + };
>> +
>> + pcie30_phy3_pipe_clk: pcie30_phy3_pipe_clk {
>> + compatible = "fixed-clock";
>> + clock-frequency = <250000000>;
>> + #clock-cells = <0>;
>> + };
>
> Why PIPE clocks are modeled as fixed clocks unlike other SoCs?
Sure, will add the clocks to corresponding PHY node and use the phandle
similar to other targets
>
>> +
>> sleep_clk: sleep-clk {
>> compatible = "fixed-clock";
>> #clock-cells = <0>;
>> };
>>
>> + usb3phy_0_cc_pipe_clk: usb3phy_0_cc_pipe_clk {
>> + compatible = "fixed-clock";
>> + clock-frequency = <125000000>;
>> + #clock-cells = <0>;
>> + };
>
> Spurious?
Will drop it
>
>> +
>> xo_board_clk: xo-board-clk {
>> compatible = "fixed-clock";
>> #clock-cells = <0>;
>> @@ -121,6 +151,155 @@
>> #size-cells = <1>;
>> ranges = <0 0 0 0xffffffff>;
>>
>> + pcie0_phy: phy@84000 {
>> + compatible = "qcom,ipq9574-qmp-gen3x1-pcie-phy";
>> + reg = <0x00084000 0x1bc>; /* Serdes PLL */
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges;
>> + clocks = <&gcc GCC_PCIE0_AUX_CLK>,
>> + <&gcc GCC_PCIE0_AHB_CLK>,
>> + <&gcc GCC_ANOC_PCIE0_1LANE_M_CLK>,
>> + <&gcc GCC_SNOC_PCIE0_1LANE_S_CLK>;
>> + clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane";
>
> Care to explain what these anoc_lane and snoc_lane clocks are?
snoc & anoc lane clocks are used in the SNOC/ANOC Network Interface Unit
(NIU) which connects to the corresponding PCIE master/slave interface
>
>> +
>> + assigned-clocks = <&gcc GCC_PCIE0_AUX_CLK>;
>> + assigned-clock-rates = <20000000>;
>> +
>> + resets = <&gcc GCC_PCIE0_PHY_BCR>,
>> + <&gcc GCC_PCIE0PHY_PHY_BCR>;
>> + reset-names = "phy", "common";
>> +
>> + status = "disabled";
>> +
>> + pcie0_lane: phy@84200 {
>> + reg = <0x00084200 0x16c>, /* Serdes Tx */
>> + <0x00084400 0x200>, /* Serdes Rx */
>> + <0x00084800 0x1f0>, /* PCS: Lane0, COM, PCIE */
>> + <0x00084c00 0xf4>; /* pcs_misc */
>> + #phy-cells = <0>;
>> +
>> + clocks = <&gcc GCC_PCIE0_PIPE_CLK>;
>> + clock-names = "pipe0";
>> + clock-output-names = "gcc_pcie0_pipe_clk_src";
>> + #clock-cells = <0>;
>> + };
>> + };
>> +
>
> [...]
>
>> + pcie1_x1: pci@10000000 {
>> + compatible = "qcom,pcie-ipq9574";
>> + reg = <0x10000000 0xf1d>,
>> + <0x10000F20 0xa8>,
>> + <0x10001000 0x1000>,
>> + <0x000F8000 0x4000>,
>> + <0x10100000 0x1000>,
>> + <0x00618108 0x4>;
>> + reg-names = "dbi", "elbi", "atu", "parf", "config", "aggr_noc";
>
> As I asked in the binding patch, why "aggr_noc" region is required?
The ANOC runs at a fixed frequency of 342MHz.
For the connected PCIe slave devices that run at lesser frequency,
the aggr_noc's rate adapter register is updated to configure
the packet transmission rate to ensure no wait cycles are inserted.
Can we use the 'syscon' property here to set the rate adapter?
>
>> + device_type = "pci";
>> + linux,pci-domain = <2>;
>> + bus-range = <0x00 0xff>;
>> + num-lanes = <1>;
>> + #address-cells = <3>;
>> + #size-cells = <2>;
>> +
>> + ranges = <0x81000000 0 0x10200000 0x10200000
>> + 0 0x00100000 /* downstream I/O */
>> + 0x82000000 0 0x10300000 0x10300000
>> + 0 0x07d00000>; /* non-prefetchable memory */
>
> Don't split the ranges and encode them in a single line.
Okay
>
> Also, the I'm not sure why you have set the relocatable flag (n) for both
> ranges i.e., in 0x81000000 and 0x82000000.
Will check and add comment in V2
>
>> +
>> + #interrupt-cells = <1>;
>> + interrupt-map-mask = <0 0 0 0x7>;
>> + interrupt-map = <0 0 0 1 &intc 0 35
>> + IRQ_TYPE_LEVEL_HIGH>, /* int_a */
>> + <0 0 0 2 &intc 0 49
>> + IRQ_TYPE_LEVEL_HIGH>, /* int_b */
>> + <0 0 0 3 &intc 0 84
>> + IRQ_TYPE_LEVEL_HIGH>, /* int_c */
>> + <0 0 0 4 &intc 0 85
>> + IRQ_TYPE_LEVEL_HIGH>; /* int_d */
>> +
>
> Again, wrap the interrupts in a single line.
Sure, okay
>
>> + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
>> + interrupt-names = "global_irq";
>> +
>
> Linux doesn't support global_irq yet. But since devicetree is supposed to
> describe the hardware, you can keep it.
Okay
>
> Above comment applies to rest of the PCIe nodes.
>
>> + /* clocks and clock-names are used to enable the clock in CBCR */
>> + clocks = <&gcc GCC_PCIE1_AHB_CLK>,
>> + <&gcc GCC_PCIE1_AUX_CLK>,
>> + <&gcc GCC_PCIE1_AXI_M_CLK>,
>> + <&gcc GCC_PCIE1_AXI_S_CLK>,
>> + <&gcc GCC_PCIE1_AXI_S_BRIDGE_CLK>,
>> + <&gcc GCC_PCIE1_RCHNG_CLK>;
>> + clock-names = "ahb",
>> + "aux",
>> + "axi_m",
>> + "axi_s",
>> + "axi_bridge",
>> + "rchng";
>> +
>> + resets = <&gcc GCC_PCIE1_PIPE_ARES>,
>> + <&gcc GCC_PCIE1_CORE_STICKY_ARES>,
>> + <&gcc GCC_PCIE1_AXI_S_STICKY_ARES>,
>> + <&gcc GCC_PCIE1_AXI_S_ARES>,
>> + <&gcc GCC_PCIE1_AXI_M_STICKY_ARES>,
>> + <&gcc GCC_PCIE1_AXI_M_ARES>,
>> + <&gcc GCC_PCIE1_AUX_ARES>,
>> + <&gcc GCC_PCIE1_AHB_ARES>;
>> + reset-names = "pipe",
>> + "sticky",
>> + "axi_s_sticky",
>> + "axi_s",
>> + "axi_m_sticky",
>> + "axi_m",
>> + "aux",
>> + "ahb";
>> +
>> + phys = <&pcie1_lane>;
>> + phy-names = "pciephy";
>> + msi-parent = <&v2m0>;
>> + status = "disabled";
>> + };
>> +
>
> [...]
>
>> + pcie2_x2: pci@20000000 {
>> + compatible = "qcom,pcie-ipq9574";
>> + reg = <0x20000000 0xf1d>,
>> + <0x20000F20 0xa8>,
>> + <0x20001000 0x1000>,
>> + <0x00088000 0x4000>,
>> + <0x20100000 0x1000>;
>> + reg-names = "dbi", "elbi", "atu", "parf", "config";
>> + device_type = "pci";
>> + linux,pci-domain = <3>;
>> + bus-range = <0x00 0xff>;
>> + num-lanes =<2>;
>
> Space after =
Sure, okay
>
> Thanks,
> Mani
>
@@ -8,6 +8,7 @@
/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
#include "ipq9574.dtsi"
/ {
@@ -29,6 +30,33 @@
status = "okay";
};
+&pcie1_phy {
+ status = "okay";
+};
+
+&pcie1_x1 {
+ perst-gpios = <&tlmm 26 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&pcie2_phy {
+ status = "okay";
+};
+
+&pcie2_x2 {
+ perst-gpios = <&tlmm 29 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&pcie3_phy {
+ status = "okay";
+};
+
+&pcie3_x2 {
+ perst-gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
&sdhc_1 {
pinctrl-0 = <&sdc_default_state>;
pinctrl-names = "default";
@@ -6,8 +6,8 @@
* Copyright (c) 2023, Qualcomm Innovation Center, Inc. All rights reserved.
*/
-#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/qcom,ipq9574-gcc.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/reset/qcom,ipq9574-gcc.h>
/ {
@@ -22,11 +22,41 @@
#clock-cells = <0>;
};
+ pcie30_phy0_pipe_clk: pcie30_phy0_pipe_clk {
+ compatible = "fixed-clock";
+ clock-frequency = <250000000>;
+ #clock-cells = <0>;
+ };
+
+ pcie30_phy1_pipe_clk: pcie30_phy1_pipe_clk {
+ compatible = "fixed-clock";
+ clock-frequency = <250000000>;
+ #clock-cells = <0>;
+ };
+
+ pcie30_phy2_pipe_clk: pcie30_phy2_pipe_clk {
+ compatible = "fixed-clock";
+ clock-frequency = <250000000>;
+ #clock-cells = <0>;
+ };
+
+ pcie30_phy3_pipe_clk: pcie30_phy3_pipe_clk {
+ compatible = "fixed-clock";
+ clock-frequency = <250000000>;
+ #clock-cells = <0>;
+ };
+
sleep_clk: sleep-clk {
compatible = "fixed-clock";
#clock-cells = <0>;
};
+ usb3phy_0_cc_pipe_clk: usb3phy_0_cc_pipe_clk {
+ compatible = "fixed-clock";
+ clock-frequency = <125000000>;
+ #clock-cells = <0>;
+ };
+
xo_board_clk: xo-board-clk {
compatible = "fixed-clock";
#clock-cells = <0>;
@@ -121,6 +151,155 @@
#size-cells = <1>;
ranges = <0 0 0 0xffffffff>;
+ pcie0_phy: phy@84000 {
+ compatible = "qcom,ipq9574-qmp-gen3x1-pcie-phy";
+ reg = <0x00084000 0x1bc>; /* Serdes PLL */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ clocks = <&gcc GCC_PCIE0_AUX_CLK>,
+ <&gcc GCC_PCIE0_AHB_CLK>,
+ <&gcc GCC_ANOC_PCIE0_1LANE_M_CLK>,
+ <&gcc GCC_SNOC_PCIE0_1LANE_S_CLK>;
+ clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane";
+
+ assigned-clocks = <&gcc GCC_PCIE0_AUX_CLK>;
+ assigned-clock-rates = <20000000>;
+
+ resets = <&gcc GCC_PCIE0_PHY_BCR>,
+ <&gcc GCC_PCIE0PHY_PHY_BCR>;
+ reset-names = "phy", "common";
+
+ status = "disabled";
+
+ pcie0_lane: phy@84200 {
+ reg = <0x00084200 0x16c>, /* Serdes Tx */
+ <0x00084400 0x200>, /* Serdes Rx */
+ <0x00084800 0x1f0>, /* PCS: Lane0, COM, PCIE */
+ <0x00084c00 0xf4>; /* pcs_misc */
+ #phy-cells = <0>;
+
+ clocks = <&gcc GCC_PCIE0_PIPE_CLK>;
+ clock-names = "pipe0";
+ clock-output-names = "gcc_pcie0_pipe_clk_src";
+ #clock-cells = <0>;
+ };
+ };
+
+ pcie2_phy: phy@8c000 {
+ compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy";
+ reg = <0x0008c000 0x1bc>; /* Serdes PLL */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ clocks = <&gcc GCC_PCIE2_AUX_CLK>,
+ <&gcc GCC_PCIE2_AHB_CLK>,
+ <&gcc GCC_ANOC_PCIE2_2LANE_M_CLK>,
+ <&gcc GCC_SNOC_PCIE2_2LANE_S_CLK>;
+ clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane";
+
+ assigned-clocks = <&gcc GCC_PCIE2_AUX_CLK>;
+ assigned-clock-rates = <20000000>;
+
+ resets = <&gcc GCC_PCIE2_PHY_BCR>,
+ <&gcc GCC_PCIE2PHY_PHY_BCR>;
+ reset-names = "phy", "common";
+
+ status = "disabled";
+
+ pcie2_lanes: phy@8c200 {
+ reg = <0x0008c200 0x16c>, /* Serdes Tx0 */
+ <0x0008c400 0x200>, /* Serdes Rx0 */
+ <0x0008d000 0x1f0>, /* PCS: Lane0, COM, PCIE */
+ <0x0008c600 0x16c>, /* Serdes Tx1 */
+ <0x0008c800 0x200>, /* Serdes Rx1 */
+ <0x0008d400 0x0f8>; /* pcs_misc */
+
+ #phy-cells = <0>;
+
+ clocks = <&gcc GCC_PCIE2_PIPE_CLK>;
+ clock-names = "pipe0";
+ clock-output-names = "gcc_pcie2_pipe_clk_src";
+ #clock-cells = <0>;
+ };
+ };
+
+ pcie3_phy: phy@f4000 {
+ compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy";
+ reg = <0x000f4000 0x1bc>; /* Serdes PLL */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ clocks = <&gcc GCC_PCIE3_AUX_CLK>,
+ <&gcc GCC_PCIE3_AHB_CLK>,
+ <&gcc GCC_ANOC_PCIE3_2LANE_M_CLK>,
+ <&gcc GCC_SNOC_PCIE3_2LANE_S_CLK>;
+ clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane";
+
+ assigned-clocks = <&gcc GCC_PCIE3_AUX_CLK>;
+ assigned-clock-rates = <20000000>;
+
+ resets = <&gcc GCC_PCIE3_PHY_BCR>,
+ <&gcc GCC_PCIE3PHY_PHY_BCR>;
+ reset-names = "phy", "common";
+
+ status = "disabled";
+
+ pcie3_lanes: phy@f4200 {
+ reg = <0x000f4200 0x16c>, /* Serdes Tx0 */
+ <0x000f4400 0x200>, /* Serdes Rx0 */
+ <0x000f5000 0x1f0>, /* PCS: Lane0, COM, PCIE */
+ <0x000f4600 0x16c>, /* Serdes Tx1 */
+ <0x000f4800 0x200>, /* Serdes Rx1 */
+ <0x000f5400 0x0f8>; /* pcs_misc */
+
+ #phy-cells = <0>;
+
+ clocks = <&gcc GCC_PCIE3_PIPE_CLK>;
+ clock-names = "pipe0";
+ clock-output-names = "gcc_pcie3_pipe_clk_src";
+ #clock-cells = <0>;
+ };
+ };
+
+ pcie1_phy: phy@fc000 {
+ compatible = "qcom,ipq9574-qmp-gen3x1-pcie-phy";
+ reg = <0x000fc000 0x1bc>; /* Serdes PLL */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ clocks = <&gcc GCC_PCIE1_AUX_CLK>,
+ <&gcc GCC_PCIE1_AHB_CLK>,
+ <&gcc GCC_ANOC_PCIE1_1LANE_M_CLK>,
+ <&gcc GCC_SNOC_PCIE1_1LANE_S_CLK>;
+ clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane";
+
+ assigned-clocks = <&gcc GCC_PCIE1_AUX_CLK>;
+ assigned-clock-rates = <20000000>;
+
+ resets = <&gcc GCC_PCIE1_PHY_BCR>,
+ <&gcc GCC_PCIE1PHY_PHY_BCR>;
+ reset-names = "phy", "common";
+
+ status = "disabled";
+
+ pcie1_lane: phy@fc200 {
+ reg = <0x000fc200 0x16c>, /* Serdes Tx */
+ <0x000fc400 0x200>, /* Serdes Rx */
+ <0x000fc800 0x1f0>, /* PCS: Lane0, COM, PCIE */
+ <0x000fcc00 0xf4>; /* pcs_misc */
+ #phy-cells = <0>;
+
+ clocks = <&gcc GCC_PCIE1_PIPE_CLK>;
+ clock-names = "pipe0";
+ clock-output-names = "gcc_pcie1_pipe_clk_src";
+ #clock-cells = <0>;
+ };
+ };
+
tlmm: pinctrl@1000000 {
compatible = "qcom,ipq9574-tlmm";
reg = <0x01000000 0x300000>;
@@ -145,11 +324,11 @@
clocks = <&xo_board_clk>,
<&sleep_clk>,
<&bias_pll_ubi_nc_clk>,
- <0>,
- <0>,
- <0>,
- <0>,
- <0>;
+ <&pcie30_phy0_pipe_clk>,
+ <&pcie30_phy1_pipe_clk>,
+ <&pcie30_phy2_pipe_clk>,
+ <&pcie30_phy3_pipe_clk>,
+ <&usb3phy_0_cc_pipe_clk>;
#clock-cells = <1>;
#reset-cells = <1>;
#power-domain-cells = <1>;
@@ -282,6 +461,292 @@
status = "disabled";
};
};
+
+ pcie1_x1: pci@10000000 {
+ compatible = "qcom,pcie-ipq9574";
+ reg = <0x10000000 0xf1d>,
+ <0x10000F20 0xa8>,
+ <0x10001000 0x1000>,
+ <0x000F8000 0x4000>,
+ <0x10100000 0x1000>,
+ <0x00618108 0x4>;
+ reg-names = "dbi", "elbi", "atu", "parf", "config", "aggr_noc";
+ device_type = "pci";
+ linux,pci-domain = <2>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <1>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x81000000 0 0x10200000 0x10200000
+ 0 0x00100000 /* downstream I/O */
+ 0x82000000 0 0x10300000 0x10300000
+ 0 0x07d00000>; /* non-prefetchable memory */
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 35
+ IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 49
+ IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 84
+ IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 85
+ IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "global_irq";
+
+ /* clocks and clock-names are used to enable the clock in CBCR */
+ clocks = <&gcc GCC_PCIE1_AHB_CLK>,
+ <&gcc GCC_PCIE1_AUX_CLK>,
+ <&gcc GCC_PCIE1_AXI_M_CLK>,
+ <&gcc GCC_PCIE1_AXI_S_CLK>,
+ <&gcc GCC_PCIE1_AXI_S_BRIDGE_CLK>,
+ <&gcc GCC_PCIE1_RCHNG_CLK>;
+ clock-names = "ahb",
+ "aux",
+ "axi_m",
+ "axi_s",
+ "axi_bridge",
+ "rchng";
+
+ resets = <&gcc GCC_PCIE1_PIPE_ARES>,
+ <&gcc GCC_PCIE1_CORE_STICKY_ARES>,
+ <&gcc GCC_PCIE1_AXI_S_STICKY_ARES>,
+ <&gcc GCC_PCIE1_AXI_S_ARES>,
+ <&gcc GCC_PCIE1_AXI_M_STICKY_ARES>,
+ <&gcc GCC_PCIE1_AXI_M_ARES>,
+ <&gcc GCC_PCIE1_AUX_ARES>,
+ <&gcc GCC_PCIE1_AHB_ARES>;
+ reset-names = "pipe",
+ "sticky",
+ "axi_s_sticky",
+ "axi_s",
+ "axi_m_sticky",
+ "axi_m",
+ "aux",
+ "ahb";
+
+ phys = <&pcie1_lane>;
+ phy-names = "pciephy";
+ msi-parent = <&v2m0>;
+ status = "disabled";
+ };
+
+ pcie3_x2: pci@18000000 {
+ compatible = "qcom,pcie-ipq9574";
+ reg = <0x18000000 0xf1d>,
+ <0x18000F20 0xa8>,
+ <0x18001000 0x1000>,
+ <0x000F0000 0x4000>,
+ <0x18100000 0x1000>;
+ reg-names = "dbi", "elbi", "atu", "parf", "config";
+ device_type = "pci";
+ linux,pci-domain = <4>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <2>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x81000000 0 0x18200000 0x18200000
+ 0 0x00100000 /* downstream I/O */
+ 0x82000000 0 0x18300000 0x18300000
+ 0 0x07d00000>; /* non-prefetchable memory */
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 189
+ IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 190
+ IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 191
+ IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 192
+ IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "global_irq";
+
+ /* clocks and clock-names are used to enable the clock in CBCR */
+ clocks = <&gcc GCC_PCIE3_AHB_CLK>,
+ <&gcc GCC_PCIE3_AUX_CLK>,
+ <&gcc GCC_PCIE3_AXI_M_CLK>,
+ <&gcc GCC_PCIE3_AXI_S_CLK>,
+ <&gcc GCC_PCIE3_AXI_S_BRIDGE_CLK>,
+ <&gcc GCC_PCIE3_RCHNG_CLK>;
+ clock-names = "ahb",
+ "aux",
+ "axi_m",
+ "axi_s",
+ "axi_bridge",
+ "rchng";
+
+ resets = <&gcc GCC_PCIE3_PIPE_ARES>,
+ <&gcc GCC_PCIE3_CORE_STICKY_ARES>,
+ <&gcc GCC_PCIE3_AXI_S_STICKY_ARES>,
+ <&gcc GCC_PCIE3_AXI_S_ARES>,
+ <&gcc GCC_PCIE3_AXI_M_STICKY_ARES>,
+ <&gcc GCC_PCIE3_AXI_M_ARES>,
+ <&gcc GCC_PCIE3_AUX_ARES>,
+ <&gcc GCC_PCIE3_AHB_ARES>;
+ reset-names = "pipe",
+ "sticky",
+ "axi_s_sticky",
+ "axi_s",
+ "axi_m_sticky",
+ "axi_m",
+ "aux",
+ "ahb";
+
+ phys = <&pcie3_lanes>;
+ phy-names = "pciephy";
+ msi-parent = <&v2m0>;
+ status = "disabled";
+ };
+
+ pcie2_x2: pci@20000000 {
+ compatible = "qcom,pcie-ipq9574";
+ reg = <0x20000000 0xf1d>,
+ <0x20000F20 0xa8>,
+ <0x20001000 0x1000>,
+ <0x00088000 0x4000>,
+ <0x20100000 0x1000>;
+ reg-names = "dbi", "elbi", "atu", "parf", "config";
+ device_type = "pci";
+ linux,pci-domain = <3>;
+ bus-range = <0x00 0xff>;
+ num-lanes =<2>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x81000000 0 0x20200000 0x20200000
+ 0 0x00100000 /* downstream I/O */
+ 0x82000000 0 0x20300000 0x20300000
+ 0 0x07d00000>; /* non-prefetchable memory */
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 164
+ IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 165
+ IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 186
+ IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 187
+ IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "global_irq";
+
+ /* clocks and clock-names are used to enable the clock in CBCR */
+ clocks = <&gcc GCC_PCIE2_AHB_CLK>,
+ <&gcc GCC_PCIE2_AUX_CLK>,
+ <&gcc GCC_PCIE2_AXI_M_CLK>,
+ <&gcc GCC_PCIE2_AXI_S_CLK>,
+ <&gcc GCC_PCIE2_AXI_S_BRIDGE_CLK>,
+ <&gcc GCC_PCIE2_RCHNG_CLK>;
+ clock-names = "ahb",
+ "aux",
+ "axi_m",
+ "axi_s",
+ "axi_bridge",
+ "rchng";
+
+ resets = <&gcc GCC_PCIE2_PIPE_ARES>,
+ <&gcc GCC_PCIE2_CORE_STICKY_ARES>,
+ <&gcc GCC_PCIE2_AXI_S_STICKY_ARES>,
+ <&gcc GCC_PCIE2_AXI_S_ARES>,
+ <&gcc GCC_PCIE2_AXI_M_STICKY_ARES>,
+ <&gcc GCC_PCIE2_AXI_M_ARES>,
+ <&gcc GCC_PCIE2_AUX_ARES>,
+ <&gcc GCC_PCIE2_AHB_ARES>;
+ reset-names = "pipe",
+ "sticky",
+ "axi_s_sticky",
+ "axi_s",
+ "axi_m_sticky",
+ "axi_m",
+ "aux",
+ "ahb";
+
+ phys = <&pcie2_lanes>;
+ phy-names = "pciephy";
+ msi-parent = <&v2m0>;
+ status = "disabled";
+ };
+
+ pcie0_x1: pci@28000000 {
+ compatible = "qcom,pcie-ipq9574";
+ reg = <0x28000000 0xf1d>,
+ <0x28000F20 0xa8>,
+ <0x28001000 0x1000>,
+ <0x00080000 0x2000>,
+ <0x28100000 0x1000>,
+ <0x00618088 0x4>;
+ reg-names = "dbi", "elbi", "atu", "parf", "config", "aggr_noc";
+ device_type = "pci";
+ linux,pci-domain = <1>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <1>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x81000000 0 0x28200000 0x28200000
+ 0 0x00100000 /* downstream I/O */
+ 0x82000000 0 0x28300000 0x28300000
+ 0 0x07d00000>; /* non-prefetchable memory */
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 75
+ IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 78
+ IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 79
+ IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 83
+ IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "global_irq";
+
+ /* clocks and clock-names are used to enable the clock in CBCR */
+ clocks = <&gcc GCC_PCIE0_AHB_CLK>,
+ <&gcc GCC_PCIE0_AUX_CLK>,
+ <&gcc GCC_PCIE0_AXI_M_CLK>,
+ <&gcc GCC_PCIE0_AXI_S_CLK>,
+ <&gcc GCC_PCIE0_AXI_S_BRIDGE_CLK>,
+ <&gcc GCC_PCIE0_RCHNG_CLK>;
+ clock-names = "ahb",
+ "aux",
+ "axi_m",
+ "axi_s",
+ "axi_bridge",
+ "rchng";
+
+ resets = <&gcc GCC_PCIE0_PIPE_ARES>,
+ <&gcc GCC_PCIE0_CORE_STICKY_ARES>,
+ <&gcc GCC_PCIE0_AXI_S_STICKY_ARES>,
+ <&gcc GCC_PCIE0_AXI_S_ARES>,
+ <&gcc GCC_PCIE0_AXI_M_STICKY_ARES>,
+ <&gcc GCC_PCIE0_AXI_M_ARES>,
+ <&gcc GCC_PCIE0_AUX_ARES>,
+ <&gcc GCC_PCIE0_AHB_ARES>;
+ reset-names = "pipe",
+ "sticky",
+ "axi_s_sticky",
+ "axi_s",
+ "axi_m_sticky",
+ "axi_m",
+ "aux",
+ "ahb";
+
+ phys = <&pcie0_lane>;
+ phy-names = "pciephy";
+ msi-parent = <&v2m0>;
+ status = "disabled";
+ };
};
timer {