[1/3] arm64: dts: qcom: sa8775p: add the i2c node for sa8775p-ride
Commit Message
From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Add the i2c node for the interface exposed on the sa8775p-ride board.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
---
arch/arm64/boot/dts/qcom/sa8775p-ride.dts | 19 +++++++++++++
arch/arm64/boot/dts/qcom/sa8775p.dtsi | 34 +++++++++++++++++++++++
2 files changed, 53 insertions(+)
@@ -13,6 +13,7 @@ / {
aliases {
serial0 = &uart10;
+ i2c18 = &i2c18;
};
chosen {
@@ -20,10 +21,21 @@ chosen {
};
};
+&i2c18 {
+ clock-frequency = <400000>;
+ pinctrl-0 = <&qup_i2c18_default>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
&qupv3_id_1 {
status = "okay";
};
+&qupv3_id_2 {
+ status = "okay";
+};
+
&sleep_clk {
clock-frequency = <32764>;
};
@@ -33,6 +45,13 @@ qup_uart10_default: qup-uart10-state {
pins = "gpio46", "gpio47";
function = "qup1_se3";
};
+
+ qup_i2c18_default: qup-i2c18-state {
+ pins = "gpio95", "gpio96";
+ function = "qup2_se4";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
};
&uart10 {
@@ -491,6 +491,40 @@ &clk_virt SLAVE_QUP_CORE_1 0>,
};
};
+ qupv3_id_2: geniqup@8c0000 {
+ compatible = "qcom,geni-se-qup";
+ reg = <0x0 0x8c0000 0x0 0x6000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ clock-names = "m-ahb", "s-ahb";
+ clocks = <&gcc GCC_QUPV3_WRAP_2_M_AHB_CLK>,
+ <&gcc GCC_QUPV3_WRAP_2_S_AHB_CLK>;
+ iommus = <&apps_smmu 0x5a3 0x0>;
+ status = "disabled";
+
+ i2c18: i2c@890000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x890000 0x0 0x4000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_2 0
+ &clk_virt SLAVE_QUP_CORE_2 0>,
+ <&gem_noc MASTER_APPSS_PROC 0
+ &config_noc SLAVE_QUP_2 0>,
+ <&aggre2_noc MASTER_QUP_2 0
+ &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core",
+ "qup-config",
+ "qup-memory";
+ power-domains = <&rpmhpd SA8775P_CX>;
+ status = "disabled";
+ };
+ };
+
intc: interrupt-controller@17a00000 {
compatible = "arm,gic-v3";
reg = <0x0 0x17a00000 0x0 0x10000>, /* GICD */