In some use cases, it is desirable to only inject idle on certain set
of CPUs. For example on Alder Lake systems, it is possible that we force
idle only on P-Cores for thermal reasons. Also the idle percent can be
more than 50% if we only choose partial set of CPUs in the system.
Introduce 2 new module parameters for this purpose. They can be only
changed when the cooling device is inactive.
cpumask (Read/Write): A bit mask of CPUs to inject idle. The format of
this bitmask is same as used in other subsystems like in
/proc/irq/*/smp_affinity. The mask is comma separated 32 bit groups.
Each CPU is one bit. For example for 256 CPU system the full mask is:
ffffffff,ffffffff,ffffffff,ffffffff,ffffffff,ffffffff,ffffffff,ffffffff
The leftmost mask is for CPU 0-32.
max_idle (Read/Write): Maximum injected idle time to the total CPU time
ratio in percent range from 1 to 100. Even if the cooling device max_state
is always 100 (100%), this parameter allows to add a max idle percent
limit. The default is 50, to match the current implementation of powerclamp
driver. Also doesn't allow value more than 75, if the cpumask includes
every CPU present in the system.
Also when the cpumask doesn't include every CPU, there is no use of
compensation using package C-state idle counters. Hence don't start
package C-state polling thread even for a single package or a single die
system in this case.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
---
v3:
One word document change from leftmost to rightmost
v2:
Addressed comments from v5 series from Rafael
Build issue reported by Rui
.../admin-guide/thermal/intel_powerclamp.rst | 22 +++
drivers/thermal/intel/intel_powerclamp.c | 177 +++++++++++++++---
2 files changed, 178 insertions(+), 21 deletions(-)
@@ -26,6 +26,8 @@ By:
- Generic Thermal Layer (sysfs)
- Kernel APIs (TBD)
+ (*) Module Parameters
+
INTRODUCTION
============
@@ -318,3 +320,23 @@ device, a PID based userspace thermal controller can manage to
control CPU temperature effectively, when no other thermal influence
is added. For example, a UltraBook user can compile the kernel under
certain temperature (below most active trip points).
+
+Module Parameters
+=================
+
+``cpumask`` (RW)
+ A bit mask of CPUs to inject idle. The format of the bitmask is same as
+ used in other subsystems like in /proc/irq/*/smp_affinity. The mask is
+ comma separated 32 bit groups. Each CPU is one bit. For example for a 256
+ CPU system the full mask is:
+ ffffffff,ffffffff,ffffffff,ffffffff,ffffffff,ffffffff,ffffffff,ffffffff
+
+ The rightmost mask is for CPU 0-32.
+
+``max_idle`` (RW)
+ Maximum injected idle time to the total CPU time ratio in percent range
+ from 1 to 100. Even if the cooling device max_state is always 100 (100%),
+ this parameter allows to add a max idle percent limit. The default is 50,
+ to match the current implementation of powerclamp driver. Also doesn't
+ allow value more than 75, if the cpumask includes every CPU present in
+ the system.
@@ -37,7 +37,7 @@
#include <asm/mwait.h>
#include <asm/cpu_device_id.h>
-#define MAX_TARGET_RATIO (50U)
+#define MAX_TARGET_RATIO (100U)
/* For each undisturbed clamping period (no extra wake ups during idle time),
* we increment the confidence counter for the given target ratio.
* CONFIDENCE_OK defines the level where runtime calibration results are
@@ -105,10 +105,144 @@ static const struct kernel_param_ops duration_ops = {
.get = param_get_int,
};
-
module_param_cb(duration, &duration_ops, &duration, 0644);
MODULE_PARM_DESC(duration, "forced idle time for each attempt in msec.");
+#define DEFAULT_MAX_IDLE 50
+#define MAX_ALL_CPU_IDLE 75
+
+static u8 max_idle = DEFAULT_MAX_IDLE;
+
+static cpumask_var_t idle_injection_cpu_mask;
+
+static int allocate_copy_idle_injection_mask(const struct cpumask *copy_mask)
+{
+ if (cpumask_available(idle_injection_cpu_mask))
+ goto copy_mask;
+
+ /* This mask is allocated only one time and freed during module exit */
+ if (!alloc_cpumask_var(&idle_injection_cpu_mask, GFP_KERNEL))
+ return -ENOMEM;
+
+copy_mask:
+ cpumask_copy(idle_injection_cpu_mask, copy_mask);
+
+ return 0;
+}
+
+/* Return true if the cpumask and idle percent combination is invalid */
+static bool check_invalid(cpumask_var_t mask, u8 idle)
+{
+ if (cpumask_equal(cpu_present_mask, mask) && idle > MAX_ALL_CPU_IDLE)
+ return true;
+
+ return false;
+}
+
+static int cpumask_set(const char *arg, const struct kernel_param *kp)
+{
+ cpumask_var_t new_mask;
+ int ret;
+
+ mutex_lock(&powerclamp_lock);
+
+ /* Can't set mask when cooling device is in use */
+ if (powerclamp_data.clamping) {
+ ret = -EAGAIN;
+ goto skip_cpumask_set;
+ }
+
+ ret = alloc_cpumask_var(&new_mask, GFP_KERNEL);
+ if (!ret)
+ goto skip_cpumask_set;
+
+ ret = bitmap_parse(arg, strlen(arg), cpumask_bits(new_mask),
+ nr_cpumask_bits);
+ if (ret)
+ goto free_cpumask_set;
+
+ if (cpumask_empty(new_mask) || check_invalid(new_mask, max_idle)) {
+ ret = -EINVAL;
+ goto free_cpumask_set;
+ }
+
+ /*
+ * When module parameters are passed from kernel command line
+ * during insmod, the module parameter callback is called
+ * before powerclamp_init(), so we can't assume that some
+ * cpumask can be allocated and copied before here. Also
+ * in this case this cpumask is used as the default mask.
+ */
+ ret = allocate_copy_idle_injection_mask(new_mask);
+
+free_cpumask_set:
+ free_cpumask_var(new_mask);
+skip_cpumask_set:
+ mutex_unlock(&powerclamp_lock);
+
+ return ret;
+}
+
+static int cpumask_get(char *buf, const struct kernel_param *kp)
+{
+ if (!cpumask_available(idle_injection_cpu_mask))
+ return -ENODEV;
+
+ return bitmap_print_to_pagebuf(false, buf, cpumask_bits(idle_injection_cpu_mask),
+ nr_cpumask_bits);
+}
+
+static const struct kernel_param_ops cpumask_ops = {
+ .set = cpumask_set,
+ .get = cpumask_get,
+};
+
+module_param_cb(cpumask, &cpumask_ops, NULL, 0644);
+MODULE_PARM_DESC(cpumask, "Mask of CPUs to use for idle injection.");
+
+static int max_idle_set(const char *arg, const struct kernel_param *kp)
+{
+ u8 new_max_idle;
+ int ret = 0;
+
+ mutex_lock(&powerclamp_lock);
+
+ /* Can't set mask when cooling device is in use */
+ if (powerclamp_data.clamping) {
+ ret = -EAGAIN;
+ goto skip_limit_set;
+ }
+
+ ret = kstrtou8(arg, 10, &new_max_idle);
+ if (ret)
+ goto skip_limit_set;
+
+ if (new_max_idle > MAX_TARGET_RATIO) {
+ ret = -EINVAL;
+ goto skip_limit_set;
+ }
+
+ if (check_invalid(idle_injection_cpu_mask, new_max_idle)) {
+ ret = -EINVAL;
+ goto skip_limit_set;
+ }
+
+ max_idle = new_max_idle;
+
+skip_limit_set:
+ mutex_unlock(&powerclamp_lock);
+
+ return ret;
+}
+
+static const struct kernel_param_ops max_idle_ops = {
+ .set = max_idle_set,
+ .get = param_get_int,
+};
+
+module_param_cb(max_idle, &max_idle_ops, &max_idle, 0644);
+MODULE_PARM_DESC(max_idle, "maximum injected idle time to the total CPU time ratio in percent range:1-100");
+
struct powerclamp_calibration_data {
unsigned long confidence; /* used for calibration, basically a counter
* gets incremented each time a clamping
@@ -460,21 +594,15 @@ static void trigger_idle_injection(void)
*/
static int powerclamp_idle_injection_register(void)
{
- /*
- * The idle inject core will only inject for online CPUs,
- * So we can register for all present CPUs. In this way
- * if some CPU goes online/offline while idle inject
- * is registered, nothing additional calls are required.
- * The same runtime and idle time is applicable for
- * newly onlined CPUs if any.
- *
- * Here cpu_present_mask can be used as is.
- * cast to (struct cpumask *) is required as the
- * cpu_present_mask is const struct cpumask *, otherwise
- * there will be compiler warnings.
- */
- ii_dev = idle_inject_register_full((struct cpumask *)cpu_present_mask,
- idle_inject_update);
+ poll_pkg_cstate_enable = false;
+ if (cpumask_equal(cpu_present_mask, idle_injection_cpu_mask)) {
+ ii_dev = idle_inject_register_full(idle_injection_cpu_mask, idle_inject_update);
+ if (topology_max_packages() == 1 && topology_max_die_per_package() == 1)
+ poll_pkg_cstate_enable = true;
+ } else {
+ ii_dev = idle_inject_register(idle_injection_cpu_mask);
+ }
+
if (!ii_dev) {
pr_err("powerclamp: idle_inject_register failed\n");
return -EAGAIN;
@@ -555,7 +683,7 @@ static int powerclamp_set_cur_state(struct thermal_cooling_device *cdev,
mutex_lock(&powerclamp_lock);
new_target_ratio = clamp(new_target_ratio, 0UL,
- (unsigned long) (MAX_TARGET_RATIO - 1));
+ (unsigned long) (max_idle - 1));
if (!powerclamp_data.target_ratio && new_target_ratio > 0) {
pr_info("Start idle injection to reduce power\n");
powerclamp_data.target_ratio = new_target_ratio;
@@ -646,15 +774,19 @@ static int __init powerclamp_init(void)
/* probe cpu features and ids here */
retval = powerclamp_probe();
+ if (retval)
+ return retval;
+
+ mutex_lock(&powerclamp_lock);
+ retval = allocate_copy_idle_injection_mask(cpu_present_mask);
+ mutex_unlock(&powerclamp_lock);
+
if (retval)
return retval;
/* set default limit, maybe adjusted during runtime based on feedback */
window_size = 2;
- if (topology_max_packages() == 1 && topology_max_die_per_package() == 1)
- poll_pkg_cstate_enable = true;
-
cooling_dev = thermal_cooling_device_register("intel_powerclamp", NULL,
&powerclamp_cooling_ops);
if (IS_ERR(cooling_dev))
@@ -679,6 +811,9 @@ static void __exit powerclamp_exit(void)
cancel_delayed_work_sync(&poll_pkg_cstate_work);
debugfs_remove_recursive(debug_dir);
+
+ if (cpumask_available(idle_injection_cpu_mask))
+ free_cpumask_var(idle_injection_cpu_mask);
}
module_exit(powerclamp_exit);