@@ -199,6 +199,15 @@ config SPI_BCM_QSPI
based platforms. This driver works for both SPI master for SPI NOR
flash device as well as MSPI device.
+config SPI_BCMBCA_HSSPI
+ tristate "Broadcom BCMBCA HS SPI controller driver"
+ depends on ARCH_BCMBCA || COMPILE_TEST
+ help
+ This enables support for the High Speed SPI controller present on
+ newer Broadcom BCMBCA SoCs. These SoCs include an updated SPI controller
+ that adds the capability to allow the driver to control chip select
+ explicitly.
+
config SPI_BITBANG
tristate "Utilities for Bitbanging SPI masters"
help
@@ -30,6 +30,7 @@ obj-$(CONFIG_SPI_BCM2835) += spi-bcm2835.o
obj-$(CONFIG_SPI_BCM2835AUX) += spi-bcm2835aux.o
obj-$(CONFIG_SPI_BCM63XX) += spi-bcm63xx.o
obj-$(CONFIG_SPI_BCM63XX_HSSPI) += spi-bcm63xx-hsspi.o
+obj-$(CONFIG_SPI_BCMBCA_HSSPI) += spi-bcmbca-hsspi.o
obj-$(CONFIG_SPI_BCM_QSPI) += spi-iproc-qspi.o spi-brcmstb-qspi.o spi-bcm-qspi.o
obj-$(CONFIG_SPI_BITBANG) += spi-bitbang.o
obj-$(CONFIG_SPI_BUTTERFLY) += spi-butterfly.o
new file mode 100644
@@ -0,0 +1,651 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Broadcom BCMBCA High Speed SPI Controller driver
+ *
+ * Copyright 2000-2010 Broadcom Corporation
+ * Copyright 2012-2013 Jonas Gorski <jogo@openwrt.org>
+ * Copyright 2019-2022 Broadcom Ltd
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/clk.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/spi/spi.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/spi/spi-mem.h>
+#include <linux/pm_runtime.h>
+
+#define HSSPI_GLOBAL_CTRL_REG 0x0
+#define GLOBAL_CTRL_CS_POLARITY_SHIFT 0
+#define GLOBAL_CTRL_CS_POLARITY_MASK 0x000000ff
+#define GLOBAL_CTRL_PLL_CLK_CTRL_SHIFT 8
+#define GLOBAL_CTRL_PLL_CLK_CTRL_MASK 0x0000ff00
+#define GLOBAL_CTRL_CLK_GATE_SSOFF BIT(16)
+#define GLOBAL_CTRL_CLK_POLARITY BIT(17)
+#define GLOBAL_CTRL_MOSI_IDLE BIT(18)
+
+#define HSSPI_GLOBAL_EXT_TRIGGER_REG 0x4
+
+#define HSSPI_INT_STATUS_REG 0x8
+#define HSSPI_INT_STATUS_MASKED_REG 0xc
+#define HSSPI_INT_MASK_REG 0x10
+
+#define HSSPI_PINGx_CMD_DONE(i) BIT((i * 8) + 0)
+#define HSSPI_PINGx_RX_OVER(i) BIT((i * 8) + 1)
+#define HSSPI_PINGx_TX_UNDER(i) BIT((i * 8) + 2)
+#define HSSPI_PINGx_POLL_TIMEOUT(i) BIT((i * 8) + 3)
+#define HSSPI_PINGx_CTRL_INVAL(i) BIT((i * 8) + 4)
+
+#define HSSPI_INT_CLEAR_ALL 0xff001f1f
+
+#define HSSPI_PINGPONG_COMMAND_REG(x) (0x80 + (x) * 0x40)
+#define PINGPONG_CMD_COMMAND_MASK 0xf
+#define PINGPONG_COMMAND_NOOP 0
+#define PINGPONG_COMMAND_START_NOW 1
+#define PINGPONG_COMMAND_START_TRIGGER 2
+#define PINGPONG_COMMAND_HALT 3
+#define PINGPONG_COMMAND_FLUSH 4
+#define PINGPONG_CMD_PROFILE_SHIFT 8
+#define PINGPONG_CMD_SS_SHIFT 12
+
+#define HSSPI_PINGPONG_STATUS_REG(x) (0x84 + (x) * 0x40)
+#define HSSPI_PINGPONG_STATUS_SRC_BUSY BIT(1)
+
+#define HSSPI_PROFILE_CLK_CTRL_REG(x) (0x100 + (x) * 0x20)
+#define CLK_CTRL_FREQ_CTRL_MASK 0x0000ffff
+#define CLK_CTRL_SPI_CLK_2X_SEL BIT(14)
+#define CLK_CTRL_ACCUM_RST_ON_LOOP BIT(15)
+#define CLK_CTRL_CLK_POLARITY BIT(16)
+
+#define HSSPI_PROFILE_SIGNAL_CTRL_REG(x) (0x104 + (x) * 0x20)
+#define SIGNAL_CTRL_LATCH_RISING BIT(12)
+#define SIGNAL_CTRL_LAUNCH_RISING BIT(13)
+#define SIGNAL_CTRL_ASYNC_INPUT_PATH BIT(16)
+
+#define HSSPI_PROFILE_MODE_CTRL_REG(x) (0x108 + (x) * 0x20)
+#define MODE_CTRL_MULTIDATA_RD_STRT_SHIFT 8
+#define MODE_CTRL_MULTIDATA_WR_STRT_SHIFT 12
+#define MODE_CTRL_MULTIDATA_RD_SIZE_SHIFT 16
+#define MODE_CTRL_MULTIDATA_WR_SIZE_SHIFT 18
+#define MODE_CTRL_MODE_3WIRE BIT(20)
+#define MODE_CTRL_PREPENDBYTE_CNT_SHIFT 24
+
+#define HSSPI_FIFO_REG(x) (0x200 + (x) * 0x200)
+
+#define HSSPI_OP_MULTIBIT BIT(11)
+#define HSSPI_OP_CODE_SHIFT 13
+#define HSSPI_OP_SLEEP (0 << HSSPI_OP_CODE_SHIFT)
+#define HSSPI_OP_READ_WRITE (1 << HSSPI_OP_CODE_SHIFT)
+#define HSSPI_OP_WRITE (2 << HSSPI_OP_CODE_SHIFT)
+#define HSSPI_OP_READ (3 << HSSPI_OP_CODE_SHIFT)
+#define HSSPI_OP_SETIRQ (4 << HSSPI_OP_CODE_SHIFT)
+
+#define HSSPI_BUFFER_LEN 512
+#define HSSPI_OPCODE_LEN 2
+
+#define HSSPI_MAX_PREPEND_LEN 15
+
+#define HSSPI_MAX_SYNC_CLOCK 30000000
+
+#define HSSPI_SPI_MAX_CS 8
+#define HSSPI_BUS_NUM 1 /* 0 is legacy SPI */
+#define HSSPI_POLL_STATUS_TIMEOUT_MS 100
+
+#define HSSPI_WAIT_MODE_POLLING 0
+#define HSSPI_WAIT_MODE_INTR 1
+#define HSSPI_WAIT_MODE_MAX HSSPI_WAIT_MODE_INTR
+
+#define SPIM_CTRL_CS_OVERRIDE_SEL_SHIFT 0
+#define SPIM_CTRL_CS_OVERRIDE_SEL_MASK 0xff
+#define SPIM_CTRL_CS_OVERRIDE_VAL_SHIFT 8
+#define SPIM_CTRL_CS_OVERRIDE_VAL_MASK 0xff
+
+struct bcmbca_hsspi {
+ struct completion done;
+ struct mutex bus_mutex;
+ struct mutex msg_mutex;
+ struct platform_device *pdev;
+ struct clk *clk;
+ struct clk *pll_clk;
+ void __iomem *regs;
+ void __iomem *spim_ctrl;
+ u8 __iomem *fifo;
+ u32 speed_hz;
+ u8 cs_polarity;
+ u32 wait_mode;
+};
+
+static ssize_t wait_mode_show(struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ struct spi_controller *ctrl = dev_get_drvdata(dev);
+ struct bcmbca_hsspi *bs = spi_master_get_devdata(ctrl);
+
+ return sprintf(buf, "%d\n", bs->wait_mode);
+}
+
+static ssize_t wait_mode_store(struct device *dev, struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct spi_controller *ctrl = dev_get_drvdata(dev);
+ struct bcmbca_hsspi *bs = spi_master_get_devdata(ctrl);
+ u32 val;
+
+ if (kstrtou32(buf, 10, &val))
+ return -EINVAL;
+
+ if (val > HSSPI_WAIT_MODE_MAX) {
+ dev_warn(dev, "invalid wait mode %u\n", val);
+ return -EINVAL;
+ }
+
+ mutex_lock(&bs->msg_mutex);
+ bs->wait_mode = val;
+ /* clear interrupt status to avoid spurious int on next transfer */
+ if (val == HSSPI_WAIT_MODE_INTR)
+ __raw_writel(HSSPI_INT_CLEAR_ALL, bs->regs + HSSPI_INT_STATUS_REG);
+ mutex_unlock(&bs->msg_mutex);
+
+ return count;
+}
+
+static DEVICE_ATTR_RW(wait_mode);
+
+static struct attribute *bcmbca_hsspi_attrs[] = {
+ &dev_attr_wait_mode.attr,
+ NULL,
+};
+
+static const struct attribute_group bcmbca_hsspi_group = {
+ .attrs = bcmbca_hsspi_attrs,
+};
+
+static void bcmbca_hsspi_set_cs(struct bcmbca_hsspi *bs, unsigned int cs,
+ bool active)
+{
+ u32 reg;
+
+ /* No cs orerriden needed for SS7 internal cs on pcm based voice dev */
+ if (cs == 7)
+ return;
+
+ mutex_lock(&bs->bus_mutex);
+
+ reg = __raw_readl(bs->spim_ctrl);
+ if (active)
+ reg |= BIT(cs + SPIM_CTRL_CS_OVERRIDE_SEL_SHIFT);
+ else
+ reg &= ~BIT(cs + SPIM_CTRL_CS_OVERRIDE_SEL_SHIFT);
+
+ __raw_writel(reg, bs->spim_ctrl);
+
+ mutex_unlock(&bs->bus_mutex);
+}
+
+static void bcmbca_hsspi_set_clk(struct bcmbca_hsspi *bs,
+ struct spi_device *spi, int hz)
+{
+ unsigned int profile = spi->chip_select;
+ u32 reg;
+
+ reg = DIV_ROUND_UP(2048, DIV_ROUND_UP(bs->speed_hz, hz));
+ __raw_writel(CLK_CTRL_ACCUM_RST_ON_LOOP | reg,
+ bs->regs + HSSPI_PROFILE_CLK_CTRL_REG(profile));
+
+ reg = __raw_readl(bs->regs + HSSPI_PROFILE_SIGNAL_CTRL_REG(profile));
+ if (hz > HSSPI_MAX_SYNC_CLOCK)
+ reg |= SIGNAL_CTRL_ASYNC_INPUT_PATH;
+ else
+ reg &= ~SIGNAL_CTRL_ASYNC_INPUT_PATH;
+ __raw_writel(reg, bs->regs + HSSPI_PROFILE_SIGNAL_CTRL_REG(profile));
+
+ mutex_lock(&bs->bus_mutex);
+ /* setup clock polarity */
+ reg = __raw_readl(bs->regs + HSSPI_GLOBAL_CTRL_REG);
+ reg &= ~GLOBAL_CTRL_CLK_POLARITY;
+ if (spi->mode & SPI_CPOL)
+ reg |= GLOBAL_CTRL_CLK_POLARITY;
+ __raw_writel(reg, bs->regs + HSSPI_GLOBAL_CTRL_REG);
+
+ mutex_unlock(&bs->bus_mutex);
+}
+
+static int bcmbca_hsspi_wait_cmd(struct bcmbca_hsspi *bs, unsigned int cs)
+{
+ unsigned long limit;
+ u32 reg = 0;
+ int rc = 0;
+
+ if (bs->wait_mode == HSSPI_WAIT_MODE_INTR) {
+ if (wait_for_completion_timeout(&bs->done, HZ) == 0)
+ rc = 1;
+ } else {
+ limit = jiffies + msecs_to_jiffies(HSSPI_POLL_STATUS_TIMEOUT_MS);
+
+ while (!time_after(jiffies, limit)) {
+ reg = __raw_readl(bs->regs + HSSPI_PINGPONG_STATUS_REG(0));
+ if (reg & HSSPI_PINGPONG_STATUS_SRC_BUSY)
+ cpu_relax();
+ else
+ break;
+ }
+ if (reg & HSSPI_PINGPONG_STATUS_SRC_BUSY)
+ rc = 1;
+ }
+
+ if (rc)
+ dev_err(&bs->pdev->dev, "transfer timed out!\n");
+
+ return rc;
+}
+
+static int bcmbca_hsspi_do_txrx(struct spi_device *spi, struct spi_transfer *t,
+ struct spi_message *msg)
+{
+ struct bcmbca_hsspi *bs = spi_master_get_devdata(spi->master);
+ unsigned int chip_select = spi->chip_select;
+ u16 opcode = 0;
+ int pending = t->len;
+ int step_size = HSSPI_BUFFER_LEN;
+ const u8 *tx = t->tx_buf;
+ u8 *rx = t->rx_buf;
+ u32 reg = 0, cs_act = 0;
+
+ bcmbca_hsspi_set_clk(bs, spi, t->speed_hz);
+
+ if (tx && rx)
+ opcode = HSSPI_OP_READ_WRITE;
+ else if (tx)
+ opcode = HSSPI_OP_WRITE;
+ else if (rx)
+ opcode = HSSPI_OP_READ;
+
+ if (opcode != HSSPI_OP_READ)
+ step_size -= HSSPI_OPCODE_LEN;
+
+ if ((opcode == HSSPI_OP_READ && t->rx_nbits == SPI_NBITS_DUAL) ||
+ (opcode == HSSPI_OP_WRITE && t->tx_nbits == SPI_NBITS_DUAL)) {
+ opcode |= HSSPI_OP_MULTIBIT;
+
+ if (t->rx_nbits == SPI_NBITS_DUAL)
+ reg |= 1 << MODE_CTRL_MULTIDATA_RD_SIZE_SHIFT;
+ if (t->tx_nbits == SPI_NBITS_DUAL)
+ reg |= 1 << MODE_CTRL_MULTIDATA_WR_SIZE_SHIFT;
+ }
+
+ __raw_writel(reg | 0xff,
+ bs->regs + HSSPI_PROFILE_MODE_CTRL_REG(chip_select));
+
+ while (pending > 0) {
+ int curr_step = min_t(int, step_size, pending);
+
+ reinit_completion(&bs->done);
+ if (tx) {
+ memcpy_toio(bs->fifo + HSSPI_OPCODE_LEN, tx, curr_step);
+ tx += curr_step;
+ }
+ __raw_writew((u16)cpu_to_be16(opcode | curr_step), bs->fifo);
+
+ /* enable interrupt */
+ if (bs->wait_mode == HSSPI_WAIT_MODE_INTR)
+ __raw_writel(HSSPI_PINGx_CMD_DONE(0),
+ bs->regs + HSSPI_INT_MASK_REG);
+
+ if (!cs_act) {
+ /* must apply cs signal as close as the cmd starts */
+ bcmbca_hsspi_set_cs(bs, chip_select, true);
+ cs_act = 1;
+ }
+
+ reg = chip_select << PINGPONG_CMD_SS_SHIFT |
+ chip_select << PINGPONG_CMD_PROFILE_SHIFT |
+ PINGPONG_COMMAND_START_NOW;
+ __raw_writel(reg, bs->regs + HSSPI_PINGPONG_COMMAND_REG(0));
+
+ if (bcmbca_hsspi_wait_cmd(bs, spi->chip_select))
+ return -ETIMEDOUT;
+
+ pending -= curr_step;
+
+ if (rx) {
+ memcpy_fromio(rx, bs->fifo, curr_step);
+ rx += curr_step;
+ }
+ }
+
+ return 0;
+}
+
+static int bcmbca_hsspi_setup(struct spi_device *spi)
+{
+ struct bcmbca_hsspi *bs = spi_master_get_devdata(spi->master);
+ u32 reg;
+
+ reg = __raw_readl(bs->regs +
+ HSSPI_PROFILE_SIGNAL_CTRL_REG(spi->chip_select));
+ reg &= ~(SIGNAL_CTRL_LAUNCH_RISING | SIGNAL_CTRL_LATCH_RISING);
+ if (spi->mode & SPI_CPHA)
+ reg |= SIGNAL_CTRL_LAUNCH_RISING;
+ else
+ reg |= SIGNAL_CTRL_LATCH_RISING;
+ __raw_writel(reg, bs->regs +
+ HSSPI_PROFILE_SIGNAL_CTRL_REG(spi->chip_select));
+
+ mutex_lock(&bs->bus_mutex);
+ reg = __raw_readl(bs->regs + HSSPI_GLOBAL_CTRL_REG);
+
+ if (spi->mode & SPI_CS_HIGH)
+ reg |= BIT(spi->chip_select);
+ else
+ reg &= ~BIT(spi->chip_select);
+ __raw_writel(reg, bs->regs + HSSPI_GLOBAL_CTRL_REG);
+
+ if (spi->mode & SPI_CS_HIGH)
+ bs->cs_polarity |= BIT(spi->chip_select);
+ else
+ bs->cs_polarity &= ~BIT(spi->chip_select);
+
+ reg = __raw_readl(bs->spim_ctrl);
+ reg &= ~BIT(spi->chip_select + SPIM_CTRL_CS_OVERRIDE_VAL_SHIFT);
+ if (spi->mode & SPI_CS_HIGH)
+ reg |= BIT(spi->chip_select + SPIM_CTRL_CS_OVERRIDE_VAL_SHIFT);
+ __raw_writel(reg, bs->spim_ctrl);
+
+ mutex_unlock(&bs->bus_mutex);
+
+ return 0;
+}
+
+static int bcmbca_hsspi_transfer_one(struct spi_master *master,
+ struct spi_message *msg)
+{
+ struct bcmbca_hsspi *bs = spi_master_get_devdata(master);
+ struct spi_transfer *t;
+ struct spi_device *spi = msg->spi;
+ int status = -EINVAL;
+ bool keep_cs = false;
+
+ mutex_lock(&bs->msg_mutex);
+ list_for_each_entry(t, &msg->transfers, transfer_list) {
+ status = bcmbca_hsspi_do_txrx(spi, t, msg);
+ if (status)
+ break;
+
+ spi_transfer_delay_exec(t);
+
+ if (t->cs_change) {
+ if (list_is_last(&t->transfer_list, &msg->transfers)) {
+ keep_cs = true;
+ } else {
+ if (!t->cs_off)
+ bcmbca_hsspi_set_cs(bs, spi->chip_select, false);
+
+ spi_transfer_cs_change_delay_exec(msg, t);
+
+ if (!list_next_entry(t, transfer_list)->cs_off)
+ bcmbca_hsspi_set_cs(bs, spi->chip_select, true);
+ }
+ } else if (!list_is_last(&t->transfer_list, &msg->transfers) &&
+ t->cs_off != list_next_entry(t, transfer_list)->cs_off) {
+ bcmbca_hsspi_set_cs(bs, spi->chip_select, t->cs_off);
+ }
+
+ msg->actual_length += t->len;
+ }
+
+ mutex_unlock(&bs->msg_mutex);
+
+ if (status || !keep_cs)
+ bcmbca_hsspi_set_cs(bs, spi->chip_select, false);
+
+ msg->status = status;
+ spi_finalize_current_message(master);
+
+ return 0;
+}
+
+static irqreturn_t bcmbca_hsspi_interrupt(int irq, void *dev_id)
+{
+ struct bcmbca_hsspi *bs = (struct bcmbca_hsspi *)dev_id;
+
+ if (__raw_readl(bs->regs + HSSPI_INT_STATUS_MASKED_REG) == 0)
+ return IRQ_NONE;
+
+ __raw_writel(HSSPI_INT_CLEAR_ALL, bs->regs + HSSPI_INT_STATUS_REG);
+ __raw_writel(0, bs->regs + HSSPI_INT_MASK_REG);
+
+ complete(&bs->done);
+
+ return IRQ_HANDLED;
+}
+
+static int bcmbca_hsspi_probe(struct platform_device *pdev)
+{
+ struct spi_master *master;
+ struct bcmbca_hsspi *bs;
+ struct resource *res_mem;
+ void __iomem *spim_ctrl;
+ void __iomem *regs;
+ struct device *dev = &pdev->dev;
+ struct clk *clk, *pll_clk = NULL;
+ int irq, ret;
+ u32 reg, rate, num_cs = HSSPI_SPI_MAX_CS;
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0)
+ return irq;
+
+ res_mem = platform_get_resource_byname(pdev, IORESOURCE_MEM, "hsspi");
+ if (!res_mem)
+ return -EINVAL;
+ regs = devm_ioremap_resource(dev, res_mem);
+ if (IS_ERR(regs))
+ return PTR_ERR(regs);
+
+ res_mem = platform_get_resource_byname(pdev, IORESOURCE_MEM, "spim-ctrl");
+ if (!res_mem)
+ return -EINVAL;
+ spim_ctrl = devm_ioremap_resource(dev, res_mem);
+ if (IS_ERR(spim_ctrl))
+ return PTR_ERR(spim_ctrl);
+
+ clk = devm_clk_get(dev, "hsspi");
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ ret = clk_prepare_enable(clk);
+ if (ret)
+ return ret;
+
+ rate = clk_get_rate(clk);
+ if (!rate) {
+ pll_clk = devm_clk_get(dev, "pll");
+
+ if (IS_ERR(pll_clk)) {
+ ret = PTR_ERR(pll_clk);
+ goto out_disable_clk;
+ }
+
+ ret = clk_prepare_enable(pll_clk);
+ if (ret)
+ goto out_disable_clk;
+
+ rate = clk_get_rate(pll_clk);
+ if (!rate) {
+ ret = -EINVAL;
+ goto out_disable_pll_clk;
+ }
+ }
+
+ master = spi_alloc_master(&pdev->dev, sizeof(*bs));
+ if (!master) {
+ ret = -ENOMEM;
+ goto out_disable_pll_clk;
+ }
+
+ bs = spi_master_get_devdata(master);
+ bs->pdev = pdev;
+ bs->clk = clk;
+ bs->pll_clk = pll_clk;
+ bs->regs = regs;
+ bs->spim_ctrl = spim_ctrl;
+ bs->speed_hz = rate;
+ bs->fifo = (u8 __iomem *) (bs->regs + HSSPI_FIFO_REG(0));
+ bs->wait_mode = HSSPI_WAIT_MODE_POLLING;
+
+ mutex_init(&bs->bus_mutex);
+ mutex_init(&bs->msg_mutex);
+ init_completion(&bs->done);
+
+ master->dev.of_node = dev->of_node;
+ if (!dev->of_node)
+ master->bus_num = HSSPI_BUS_NUM;
+
+ of_property_read_u32(dev->of_node, "num-cs", &num_cs);
+ if (num_cs > 8) {
+ dev_warn(dev, "unsupported number of cs (%i), reducing to 8\n",
+ num_cs);
+ num_cs = HSSPI_SPI_MAX_CS;
+ }
+ master->num_chipselect = num_cs;
+ master->setup = bcmbca_hsspi_setup;
+ master->transfer_one_message = bcmbca_hsspi_transfer_one;
+ master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH |
+ SPI_RX_DUAL | SPI_TX_DUAL;
+ master->bits_per_word_mask = SPI_BPW_MASK(8);
+ master->auto_runtime_pm = true;
+
+ platform_set_drvdata(pdev, master);
+
+ /* Initialize the hardware */
+ __raw_writel(0, bs->regs + HSSPI_INT_MASK_REG);
+
+ /* clean up any pending interrupts */
+ __raw_writel(HSSPI_INT_CLEAR_ALL, bs->regs + HSSPI_INT_STATUS_REG);
+
+ /* read out default CS polarities */
+ reg = __raw_readl(bs->regs + HSSPI_GLOBAL_CTRL_REG);
+ bs->cs_polarity = reg & GLOBAL_CTRL_CS_POLARITY_MASK;
+ __raw_writel(reg | GLOBAL_CTRL_CLK_GATE_SSOFF,
+ bs->regs + HSSPI_GLOBAL_CTRL_REG);
+
+ if (irq > 0) {
+ ret = devm_request_irq(dev, irq, bcmbca_hsspi_interrupt, IRQF_SHARED,
+ pdev->name, bs);
+ if (ret)
+ goto out_put_master;
+ }
+
+ pm_runtime_enable(&pdev->dev);
+
+ if (sysfs_create_group(&pdev->dev.kobj, &bcmbca_hsspi_group)) {
+ dev_err(&pdev->dev, "couldn't register sysfs group\n");
+ goto out_pm_disable;
+ }
+
+ /* register and we are done */
+ ret = devm_spi_register_master(dev, master);
+ if (ret)
+ goto out_sysgroup_disable;
+
+ dev_info(dev, "Broadcom BCMBCA High Speed SPI Controller driver");
+
+ return 0;
+
+out_sysgroup_disable:
+ sysfs_remove_group(&pdev->dev.kobj, &bcmbca_hsspi_group);
+out_pm_disable:
+ pm_runtime_disable(&pdev->dev);
+out_put_master:
+ spi_master_put(master);
+out_disable_pll_clk:
+ clk_disable_unprepare(pll_clk);
+out_disable_clk:
+ clk_disable_unprepare(clk);
+ return ret;
+}
+
+static int bcmbca_hsspi_remove(struct platform_device *pdev)
+{
+ struct spi_master *master = platform_get_drvdata(pdev);
+ struct bcmbca_hsspi *bs = spi_master_get_devdata(master);
+
+ /* reset the hardware and block queue progress */
+ __raw_writel(0, bs->regs + HSSPI_INT_MASK_REG);
+ clk_disable_unprepare(bs->pll_clk);
+ clk_disable_unprepare(bs->clk);
+ sysfs_remove_group(&pdev->dev.kobj, &bcmbca_hsspi_group);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int bcmbca_hsspi_suspend(struct device *dev)
+{
+ struct spi_master *master = dev_get_drvdata(dev);
+ struct bcmbca_hsspi *bs = spi_master_get_devdata(master);
+
+ spi_master_suspend(master);
+ clk_disable_unprepare(bs->pll_clk);
+ clk_disable_unprepare(bs->clk);
+
+ return 0;
+}
+
+static int bcmbca_hsspi_resume(struct device *dev)
+{
+ struct spi_master *master = dev_get_drvdata(dev);
+ struct bcmbca_hsspi *bs = spi_master_get_devdata(master);
+ int ret;
+
+ ret = clk_prepare_enable(bs->clk);
+ if (ret)
+ return ret;
+
+ if (bs->pll_clk) {
+ ret = clk_prepare_enable(bs->pll_clk);
+ if (ret) {
+ clk_disable_unprepare(bs->clk);
+ return ret;
+ }
+ }
+
+ spi_master_resume(master);
+
+ return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(bcmbca_hsspi_pm_ops, bcmbca_hsspi_suspend,
+ bcmbca_hsspi_resume);
+
+static const struct of_device_id bcmbca_hsspi_of_match[] = {
+ { .compatible = "brcm,bcmbca-hsspi-v1.1", },
+ {},
+};
+
+MODULE_DEVICE_TABLE(of, bcmbca_hsspi_of_match);
+
+static struct platform_driver bcmbca_hsspi_driver = {
+ .driver = {
+ .name = "bcmbca-hsspi",
+ .pm = &bcmbca_hsspi_pm_ops,
+ .of_match_table = bcmbca_hsspi_of_match,
+ },
+ .probe = bcmbca_hsspi_probe,
+ .remove = bcmbca_hsspi_remove,
+};
+
+module_platform_driver(bcmbca_hsspi_driver);
+
+MODULE_ALIAS("platform:bcmbca_hsspi");
+MODULE_DESCRIPTION("Broadcom BCMBCA High Speed SPI Controller driver");
+MODULE_LICENSE("GPL");