[26/35] Documentation: sound: correct spelling
Commit Message
Correct spelling problems for Documentation/sound/ as reported
by codespell.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: alsa-devel@alsa-project.org
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
---
Documentation/sound/alsa-configuration.rst | 8 ++++----
Documentation/sound/cards/audigy-mixer.rst | 2 +-
Documentation/sound/cards/maya44.rst | 2 +-
Documentation/sound/cards/sb-live-mixer.rst | 2 +-
Documentation/sound/designs/jack-controls.rst | 2 +-
Documentation/sound/designs/seq-oss.rst | 2 +-
Documentation/sound/hd-audio/notes.rst | 2 +-
7 files changed, 10 insertions(+), 10 deletions(-)
Comments
On Fri, 27 Jan 2023 07:39:56 +0100,
Randy Dunlap wrote:
>
> Correct spelling problems for Documentation/sound/ as reported
> by codespell.
>
> Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
> Cc: Jaroslav Kysela <perex@perex.cz>
> Cc: Takashi Iwai <tiwai@suse.com>
> Cc: alsa-devel@alsa-project.org
> Cc: Jonathan Corbet <corbet@lwn.net>
> Cc: linux-doc@vger.kernel.org
Applied this one now to for-next branch. Thanks.
Takashi
@@ -17,7 +17,7 @@ Digital mixer controls
======================
These controls are built using the DSP instructions. They offer extended
-functionality. Only the default build-in code in the ALSA driver is described
+functionality. Only the default built-in code in the ALSA driver is described
here. Note that the controls work as attenuators: the maximum value is the
neutral position leaving the signal unchanged. Note that if the same destination
is mentioned in multiple controls, the signal is accumulated and can be wrapped
@@ -156,7 +156,7 @@ IEC958 Output
S/PDIF should output the same signal as channel 3+4. [untested!]
-Digitial output selectors
+Digital output selectors
These switches allow a direct digital routing from the ADCs to the DACs.
Each switch determines where the digital input data to one of the DACs comes from.
They are not supported by the ESI windows driver.
@@ -8,7 +8,7 @@ Why we need Jack kcontrols
ALSA uses kcontrols to export audio controls(switch, volume, Mux, ...)
to user space. This means userspace applications like pulseaudio can
switch off headphones and switch on speakers when no headphones are
-pluged in.
+plugged in.
The old ALSA jack code only created input devices for each registered
jack. These jack input devices are not readable by userspace devices
@@ -96,7 +96,7 @@ if you use an AWE64 card, you'll see lik
Number of synth devices: 1
synth 0: [EMU8000]
type 0x1 : subtype 0x20 : voices 32
- capabilties : ioctl enabled / load_patch enabled
+ capabilities : ioctl enabled / load_patch enabled
Number of MIDI devices: 3
midi 0: [Emu8000 Port-0] ALSA port 65:0
@@ -31,7 +31,7 @@ Digital mixer controls
======================
These controls are built using the DSP instructions. They offer extended
-functionality. Only the default build-in code in the ALSA driver is described
+functionality. Only the default built-in code in the ALSA driver is described
here. Note that the controls work as attenuators: the maximum value is the
neutral position leaving the signal unchanged. Note that if the same destination
is mentioned in multiple controls, the signal is accumulated and can be wrapped
@@ -500,7 +500,7 @@ add_jack_modes (bool)
change the headphone amp and mic bias VREF capabilities
power_save_node (bool)
advanced power management for each widget, controlling the power
- sate (D0/D3) of each widget node depending on the actual pin and
+ state (D0/D3) of each widget node depending on the actual pin and
stream states
power_down_unused (bool)
power down the unused widgets, a subset of power_save_node, and
@@ -70,7 +70,7 @@ dsp_map
PCM device number maps assigned to the 1st OSS device;
Default: 0
adsp_map
- PCM device number maps assigned to the 2st OSS device;
+ PCM device number maps assigned to the 2nd OSS device;
Default: 1
nonblock_open
Don't block opening busy PCM devices;
@@ -97,7 +97,7 @@ midi_map
MIDI device number maps assigned to the 1st OSS device;
Default: 0
amidi_map
- MIDI device number maps assigned to the 2st OSS device;
+ MIDI device number maps assigned to the 2nd OSS device;
Default: 1
Module snd-soc-core
@@ -727,9 +727,9 @@ Module for EMU10K1/EMU10k2 based PCI sou
* Sound Blaster Audigy
extin
- bitmap of available external inputs for FX8010 (see bellow)
+ bitmap of available external inputs for FX8010 (see below)
extout
- bitmap of available external outputs for FX8010 (see bellow)
+ bitmap of available external outputs for FX8010 (see below)
seq_ports
allocated sequencer ports (4 by default)
max_synth_voices