[v7,4/7] dt-bindings: media: add TI DS90UB960 FPD-Link III Deserializer

  Add DT bindings for TI DS90UB960 FPD-Link III Deserializer.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 .../bindings/media/i2c/ti,ds90ub960.yaml      | 425 ++++++++++++++++++
 1 file changed, 425 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/i2c/ti,ds90ub960.yaml
  

Hi Tomi,

Thank you for the patch.

On Wed, Jan 18, 2023 at 02:40:28PM +0200, Tomi Valkeinen wrote:
> Add DT bindings for TI DS90UB960 FPD-Link III Deserializer.
> 
> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
> Reviewed-by: Rob Herring <robh@kernel.org>
> ---
>  .../bindings/media/i2c/ti,ds90ub960.yaml      | 425 ++++++++++++++++++
>  1 file changed, 425 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/i2c/ti,ds90ub960.yaml
> 
> diff --git a/Documentation/devicetree/bindings/media/i2c/ti,ds90ub960.yaml b/Documentation/devicetree/bindings/media/i2c/ti,ds90ub960.yaml
> new file mode 100644
> index 000000000000..1ba22450cdba
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/i2c/ti,ds90ub960.yaml
> @@ -0,0 +1,425 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/media/i2c/ti,ds90ub960.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Texas Instruments DS90UB9XX Family FPD-Link Deserializer Hubs
> +
> +maintainers:
> +  - Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
> +
> +description:
> +  The TI DS90UB9XX devices are FPD-Link video deserializers with I2C and GPIO
> +  forwarding.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - ti,ds90ub960-q1
> +      - ti,ds90ub9702-q1
> +
> +  reg:
> +    maxItems: 1
> +
> +  clocks:
> +    maxItems: 1
> +    description:
> +      Reference clock connected to the REFCLK pin.
> +
> +  clock-names:
> +    items:
> +      - const: refclk
> +
> +  powerdown-gpios:
> +    maxItems: 1
> +    description:
> +      Specifier for the GPIO connected to the PDB pin.
> +
> +  i2c-alias-pool:
> +    $ref: /schemas/types.yaml#/definitions/uint16-array
> +    description:
> +      I2C alias pool is a pool of I2C addresses on the main I2C bus that can be
> +      used to access the remote peripherals on the serializer's I2C bus. The
> +      addresses must be available, not used by any other peripheral. Each
> +      remote peripheral is assigned an alias from the pool, and transactions to
> +      that address will be forwarded to the remote peripheral, with the address
> +      translated to the remote peripheral's real address. This property is not
> +      needed if there are no I2C addressable remote peripherals.
> +
> +  links:
> +    type: object
> +    additionalProperties: false
> +
> +    properties:
> +      '#address-cells':
> +        const: 1
> +
> +      '#size-cells':
> +        const: 0
> +
> +      ti,manual-strobe:
> +        type: boolean
> +        description:
> +          Enable manual strobe position and EQ level
> +
> +    patternProperties:
> +      '^link@[0-3]$':
> +        type: object
> +        additionalProperties: false
> +        properties:
> +          reg:
> +            description: The link number
> +            maxItems: 1
> +
> +          i2c-alias:
> +            description:
> +              The I2C address used for the serializer. Transactions to this
> +              address on the I2C bus where the deserializer resides are
> +              forwarded to the serializer.
> +
> +          ti,rx-mode:
> +            $ref: /schemas/types.yaml#/definitions/uint32
> +            enum:
> +              - 0 # RAW10
> +              - 1 # RAW12 HF
> +              - 2 # RAW12 LF
> +              - 3 # CSI2 SYNC
> +              - 4 # CSI2 NON-SYNC
> +            description:
> +              FPD-Link Input Mode. This should reflect the hardware and the
> +              default mode of the connected device.
> +
> +          ti,cdr-mode:
> +            $ref: /schemas/types.yaml#/definitions/uint32
> +            enum:
> +              - 0 # FPD-Link III
> +              - 1 # FPD-Link IV
> +            description:
> +              FPD-Link CDR Mode. This should reflect the hardware and the
> +              default mode of the connected device.
> +
> +          ti,strobe-pos:
> +            $ref: /schemas/types.yaml#/definitions/int32
> +            minimum: -13
> +            maximum: 13
> +            description: Manual strobe position
> +
> +          ti,eq-level:
> +            $ref: /schemas/types.yaml#/definitions/uint32
> +            maximum: 14
> +            description: Manual EQ level
> +
> +          serializer:
> +            type: object
> +            description: FPD-Link Serializer node
> +
> +        required:
> +          - reg
> +          - i2c-alias
> +          - ti,rx-mode
> +          - serializer
> +
> +  ports:
> +    $ref: /schemas/graph.yaml#/properties/ports
> +
> +    properties:
> +      port@0:
> +        $ref: /schemas/graph.yaml#/$defs/port-base
> +        unevaluatedProperties: false
> +        description: FPD-Link input 0
> +
> +        properties:
> +          endpoint:
> +            $ref: /schemas/media/video-interfaces.yaml#
> +            unevaluatedProperties: false
> +            description:
> +              Endpoint for FPD-Link port. If the RX mode for this port is RAW,
> +              hsync-active and vsync-active must be defined.
> +
> +      port@1:
> +        $ref: /schemas/graph.yaml#/$defs/port-base
> +        unevaluatedProperties: false
> +        description: FPD-Link input 1
> +
> +        properties:
> +          endpoint:
> +            $ref: /schemas/media/video-interfaces.yaml#
> +            unevaluatedProperties: false
> +            description:
> +              Endpoint for FPD-Link port. If the RX mode for this port is RAW,
> +              hsync-active and vsync-active must be defined.
> +
> +      port@2:
> +        $ref: /schemas/graph.yaml#/$defs/port-base
> +        unevaluatedProperties: false
> +        description: FPD-Link input 2
> +
> +        properties:
> +          endpoint:
> +            $ref: /schemas/media/video-interfaces.yaml#
> +            unevaluatedProperties: false
> +            description:
> +              Endpoint for FPD-Link port. If the RX mode for this port is RAW,
> +              hsync-active and vsync-active must be defined.
> +
> +      port@3:
> +        $ref: /schemas/graph.yaml#/$defs/port-base
> +        unevaluatedProperties: false
> +        description: FPD-Link input 3
> +
> +        properties:
> +          endpoint:
> +            $ref: /schemas/media/video-interfaces.yaml#
> +            unevaluatedProperties: false
> +            description:
> +              Endpoint for FPD-Link port. If the RX mode for this port is RAW,
> +              hsync-active and vsync-active must be defined.
> +
> +      port@4:
> +        $ref: /schemas/graph.yaml#/$defs/port-base
> +        unevaluatedProperties: false
> +        description: CSI-2 Output 0
> +
> +        properties:
> +          endpoint:
> +            $ref: /schemas/media/video-interfaces.yaml#
> +            unevaluatedProperties: false
> +
> +            properties:
> +              data-lanes:
> +                minItems: 1
> +                maxItems: 4
> +
> +            required:
> +              - data-lanes
> +
> +      port@5:
> +        $ref: /schemas/graph.yaml#/$defs/port-base
> +        unevaluatedProperties: false
> +        description: CSI-2 Output 1
> +
> +        properties:
> +          endpoint:
> +            $ref: /schemas/media/video-interfaces.yaml#
> +            unevaluatedProperties: false
> +
> +            properties:
> +              data-lanes:
> +                minItems: 1
> +                maxItems: 4
> +
> +            required:
> +              - data-lanes
> +
> +    required:
> +      - port@0
> +      - port@1
> +      - port@2
> +      - port@3
> +      - port@4
> +      - port@5
> +
> +required:
> +  - compatible
> +  - reg
> +  - clocks
> +  - clock-names
> +  - ports
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/gpio/gpio.h>
> +
> +    i2c {
> +      clock-frequency = <400000>;
> +      #address-cells = <1>;
> +      #size-cells = <0>;
> +
> +      deser@3d {
> +        compatible = "ti,ds90ub960-q1";
> +        reg = <0x3d>;
> +
> +        clock-names = "refclk";
> +        clocks = <&fixed_clock>;
> +
> +        powerdown-gpios = <&pca9555 7 GPIO_ACTIVE_LOW>;
> +
> +        i2c-alias-pool = /bits/ 16 <0x4a 0x4b 0x4c 0x4d 0x4e 0x4f>;
> +
> +        ports {
> +          #address-cells = <1>;
> +          #size-cells = <0>;
> +
> +          /* Port 0, Camera 0 */
> +          port@0 {
> +            reg = <0>;
> +
> +            ub960_fpd3_1_in: endpoint {
> +              remote-endpoint = <&ub953_1_out>;
> +            };
> +          };
> +
> +          /* Port 1, Camera 1 */
> +          port@1 {
> +            reg = <1>;
> +
> +            ub960_fpd3_2_in: endpoint {
> +              remote-endpoint = <&ub913_2_out>;
> +              hsync-active = <0>;
> +              vsync-active = <1>;
> +            };
> +          };
> +
> +          /* Port 2, unused */

Minor comment. I'd write "unconnected" instead of "unused" (same below).
Either way,

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

> +          port@2 {
> +            reg = <2>;
> +          };
> +
> +          /* Port 3, unused */
> +          port@3 {
> +            reg = <3>;
> +          };
> +
> +          /* Port 4, CSI-2 TX */
> +          port@4 {
> +            reg = <4>;
> +            ds90ub960_0_csi_out: endpoint {
> +              data-lanes = <1 2 3 4>;
> +              link-frequencies = /bits/ 64 <800000000>;
> +              remote-endpoint = <&csi2_phy0>;
> +            };
> +          };
> +
> +          /* Port 5, unused */
> +          port@5 {
> +            reg = <5>;
> +          };
> +        };
> +
> +        links {
> +          #address-cells = <1>;
> +          #size-cells = <0>;
> +
> +          /* Link 0 has DS90UB953 serializer and IMX274 sensor */
> +
> +          link@0 {
> +            reg = <0>;
> +            i2c-alias = <0x44>;
> +
> +            ti,rx-mode = <3>;
> +
> +            serializer1: serializer {
> +              compatible = "ti,ds90ub953-q1";
> +
> +              gpio-controller;
> +              #gpio-cells = <2>;
> +
> +              #clock-cells = <0>;
> +
> +              ports {
> +                #address-cells = <1>;
> +                #size-cells = <0>;
> +
> +                port@0 {
> +                  reg = <0>;
> +                  ub953_1_in: endpoint {
> +                    data-lanes = <1 2 3 4>;
> +                    remote-endpoint = <&sensor_1_out>;
> +                  };
> +                };
> +
> +                port@1 {
> +                  reg = <1>;
> +
> +                  ub953_1_out: endpoint {
> +                    remote-endpoint = <&ub960_fpd3_1_in>;
> +                  };
> +                };
> +              };
> +
> +              i2c {
> +                #address-cells = <1>;
> +                #size-cells = <0>;
> +
> +                sensor@1a {
> +                  compatible = "sony,imx274";
> +                  reg = <0x1a>;
> +
> +                  reset-gpios = <&serializer1 0 GPIO_ACTIVE_LOW>;
> +
> +                  port {
> +                    sensor_1_out: endpoint {
> +                      remote-endpoint = <&ub953_1_in>;
> +                    };
> +                  };
> +                };
> +              };
> +            };
> +          };  /* End of link@0 */
> +
> +          /* Link 1 has DS90UB913 serializer and MT9V111 sensor */
> +
> +          link@1 {
> +            reg = <1>;
> +            i2c-alias = <0x45>;
> +
> +            ti,rx-mode = <0>;
> +
> +            serializer2: serializer {
> +              compatible = "ti,ds90ub913a-q1";
> +
> +              gpio-controller;
> +              #gpio-cells = <2>;
> +
> +              clocks = <&clk_cam_48M>;
> +              clock-names = "clkin";
> +
> +              #clock-cells = <0>;
> +
> +              ports {
> +                #address-cells = <1>;
> +                #size-cells = <0>;
> +
> +                port@0 {
> +                  reg = <0>;
> +                  ub913_2_in: endpoint {
> +                    remote-endpoint = <&sensor_2_out>;
> +                    pclk-sample = <1>;
> +                  };
> +                };
> +
> +                port@1 {
> +                  reg = <1>;
> +
> +                  ub913_2_out: endpoint {
> +                    remote-endpoint = <&ub960_fpd3_2_in>;
> +                  };
> +                };
> +              };
> +
> +              i2c {
> +                #address-cells = <1>;
> +                #size-cells = <0>;
> +
> +                sensor@48 {
> +                  compatible = "aptina,mt9v111";
> +                  reg = <0x48>;
> +
> +                  clocks = <&serializer2>;
> +
> +                  port {
> +                    sensor_2_out: endpoint {
> +                      remote-endpoint = <&ub913_2_in>;
> +                    };
> +                  };
> +                };
> +              };
> +            };
> +          }; /* End of link@1 */
> +        };
> +      };
> +    };
> +...