diff mbox series

[v2,3/9] arm64: dts: amlogic: Used onboard usb hub reset on odroid c2

Message ID 20230118044418.875-4-linux.amoon@gmail.com
State New
Headers
Series [v2,1/9] dt-bindings: usb: Add device id for Genesys Logic hub controller |

Commit Message

Anand Moon Jan. 18, 2023, 4:44 a.m. UTC 
  On Odroid c2 previously use gpio-hog to reset the usb hub,
switch to used on-board usb hub reset to enable the usb hub
and enable power to hub.

Signed-off-by: Anand Moon <linux.amoon@gmail.com>
---
v2 - drop the vendor name from compatible string.
   - move the hub node to USB controller node.
   - drop the usb_otg_pwr since it only liked to OTG port
         and link p5v0 to the vdd-supply.
---
 .../boot/dts/amlogic/meson-gxbb-odroidc2.dts  | 26 ++++++++-----------
 1 file changed, 11 insertions(+), 15 deletions(-)

Comments

Neil Armstrong Jan. 18, 2023, 8:27 a.m. UTC | #1 
On 18/01/2023 05:44, Anand Moon wrote:
> On Odroid c2 previously use gpio-hog to reset the usb hub,
> switch to used on-board usb hub reset to enable the usb hub
> and enable power to hub.
> 
> Signed-off-by: Anand Moon <linux.amoon@gmail.com>
> ---
> v2 - drop the vendor name from compatible string.
>     - move the hub node to USB controller node.
>     - drop the usb_otg_pwr since it only liked to OTG port
>           and link p5v0 to the vdd-supply.
> ---
>   .../boot/dts/amlogic/meson-gxbb-odroidc2.dts  | 26 ++++++++-----------
>   1 file changed, 11 insertions(+), 15 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
> index 201596247fd9..01356437a077 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
> @@ -250,21 +250,6 @@ eth_phy0: ethernet-phy@0 {
>   	};
>   };
>   
> -&gpio_ao {
> -	/*
> -	 * WARNING: The USB Hub on the Odroid-C2 needs a reset signal
> -	 * to be turned high in order to be detected by the USB Controller
> -	 * This signal should be handled by a USB specific power sequence
> -	 * in order to reset the Hub when USB bus is powered down.
> -	 */
> -	hog-0 {
> -		gpio-hog;
> -		gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>;
> -		output-high;
> -		line-name = "usb-hub-reset";
> -	};
> -};
> -
>   &hdmi_tx {
>   	status = "okay";
>   	pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
> @@ -414,5 +399,16 @@ &usb0 {
>   };
>   
>   &usb1 {
> +	dr_mode = "host";
> +	#address-cells = <1>;
> +	#size-cells = <0>;
>   	status = "okay";
> +
> +	hub@1 {
> +		/* Genesys Logic GL852G USB 2.0 hub */
> +		compatible = "usb5e3,610";
> +		reg = <1>;
> +		vdd-supply = <&p5v0>;
> +		reset-gpio = <&gpio_ao GPIOAO_4 GPIO_ACTIVE_LOW>;
> +	};
>   };

Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
index 201596247fd9..01356437a077 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
@@ -250,21 +250,6 @@  eth_phy0: ethernet-phy@0 {
 	};
 };
 
-&gpio_ao {
-	/*
-	 * WARNING: The USB Hub on the Odroid-C2 needs a reset signal
-	 * to be turned high in order to be detected by the USB Controller
-	 * This signal should be handled by a USB specific power sequence
-	 * in order to reset the Hub when USB bus is powered down.
-	 */
-	hog-0 {
-		gpio-hog;
-		gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "usb-hub-reset";
-	};
-};
-
 &hdmi_tx {
 	status = "okay";
 	pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
@@ -414,5 +399,16 @@  &usb0 {
 };
 
 &usb1 {
+	dr_mode = "host";
+	#address-cells = <1>;
+	#size-cells = <0>;
 	status = "okay";
+
+	hub@1 {
+		/* Genesys Logic GL852G USB 2.0 hub */
+		compatible = "usb5e3,610";
+		reg = <1>;
+		vdd-supply = <&p5v0>;
+		reset-gpio = <&gpio_ao GPIOAO_4 GPIO_ACTIVE_LOW>;
+	};
 };