[v6,1/3] remoteproc: k3-r5: Simplify single core config set
Commit Message
The config PROC_BOOT_CFG_FLAG_R5_SINGLE_CORE
is set only when cluster mode is set to
CLUSTER_MODE_SINGLECPU and cluster mode
is already configured before setting this config.
So directly check for cluster mode instead of checking
soc_data->single_cpu_mode first and then checking
cluster mode.
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
---
V6: No change
---
drivers/remoteproc/ti_k3_r5_remoteproc.c | 17 ++++++++---------
1 file changed, 8 insertions(+), 9 deletions(-)
Comments
On Mon, Jan 16, 2023 at 08:49:04PM +0530, Devarsh Thakkar wrote:
> The config PROC_BOOT_CFG_FLAG_R5_SINGLE_CORE
> is set only when cluster mode is set to
> CLUSTER_MODE_SINGLECPU and cluster mode
> is already configured before setting this config.
>
> So directly check for cluster mode instead of checking
> soc_data->single_cpu_mode first and then checking
> cluster mode.
>
> Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
> ---
> V6: No change
> ---
> drivers/remoteproc/ti_k3_r5_remoteproc.c | 17 ++++++++---------
> 1 file changed, 8 insertions(+), 9 deletions(-)
>
> diff --git a/drivers/remoteproc/ti_k3_r5_remoteproc.c b/drivers/remoteproc/ti_k3_r5_remoteproc.c
> index 0481926c6975..036c9dc217f3 100644
> --- a/drivers/remoteproc/ti_k3_r5_remoteproc.c
> +++ b/drivers/remoteproc/ti_k3_r5_remoteproc.c
> @@ -875,15 +875,14 @@ static int k3_r5_rproc_configure(struct k3_r5_rproc *kproc)
> boot_vec = 0x0;
> if (core == core0) {
> clr_cfg = PROC_BOOT_CFG_FLAG_R5_TEINIT;
> - if (cluster->soc_data->single_cpu_mode) {
> - /*
> - * Single-CPU configuration bit can only be configured
> - * on Core0 and system firmware will NACK any requests
> - * with the bit configured, so program it only on
> - * permitted cores
> - */
> - if (cluster->mode == CLUSTER_MODE_SINGLECPU)
> - set_cfg = PROC_BOOT_CFG_FLAG_R5_SINGLE_CORE;
> + /*
> + * Single-CPU configuration bit can only be configured
> + * on Core0 and system firmware will NACK any requests
> + * with the bit configured, so program it only on
> + * permitted cores
> + */
> + if (cluster->mode == CLUSTER_MODE_SINGLECPU) {
> + set_cfg = PROC_BOOT_CFG_FLAG_R5_SINGLE_CORE;
This is exactly the kind of buggy situation I want to avoid by asking to use
soc_data->single_cpu_mode only in probe().
> } else {
> /*
> * LockStep configuration bit is Read-only on Split-mode
> --
> 2.34.1
>
@@ -875,15 +875,14 @@ static int k3_r5_rproc_configure(struct k3_r5_rproc *kproc)
boot_vec = 0x0;
if (core == core0) {
clr_cfg = PROC_BOOT_CFG_FLAG_R5_TEINIT;
- if (cluster->soc_data->single_cpu_mode) {
- /*
- * Single-CPU configuration bit can only be configured
- * on Core0 and system firmware will NACK any requests
- * with the bit configured, so program it only on
- * permitted cores
- */
- if (cluster->mode == CLUSTER_MODE_SINGLECPU)
- set_cfg = PROC_BOOT_CFG_FLAG_R5_SINGLE_CORE;
+ /*
+ * Single-CPU configuration bit can only be configured
+ * on Core0 and system firmware will NACK any requests
+ * with the bit configured, so program it only on
+ * permitted cores
+ */
+ if (cluster->mode == CLUSTER_MODE_SINGLECPU) {
+ set_cfg = PROC_BOOT_CFG_FLAG_R5_SINGLE_CORE;
} else {
/*
* LockStep configuration bit is Read-only on Split-mode