[v2] arm64: dts: qcom: sdm845-tama: Add volume up and camera GPIO keys
Commit Message
Tama has four GPIO-wired keys: two for camera focus and shutter /
snapshot, and two more for volume up and down. As per the comment these
used to not work because the necessary pin bias was missing, which is
now set via pinctrl on pm8998_gpios.
The missing bias has also been added to the existing volume down button,
which receives a node name and label cleanup at the same time to be more
consistent with other DTS and the newly added buttons. Its deprecated
gpio-key,wakeup property has also been replaced with wakeup-source.
Note that volume up is also available through the usual PON RESIN node,
but unlike other platforms only triggers when the power button is held
down at the same time making it unsuitable to serve as KEY_VOLUMEUP.
Fixes: 30a7f99befc6 ("arm64: dts: qcom: Add support for SONY Xperia XZ2 / XZ2C / XZ3 (Tama platform)")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
---
Changes since v1:
- Rebased on next-20230109 and replace pm8998_gpio with plural
pm8998_gpios phandle label.
v1: https://lore.kernel.org/linux-arm-msm/20221222190656.31664-1-marijn.suijten@somainline.org/
.../dts/qcom/sdm845-sony-xperia-tama.dtsi | 72 +++++++++++++++++--
1 file changed, 68 insertions(+), 4 deletions(-)
Comments
On Tue, 10 Jan 2023 00:41:32 +0100, Marijn Suijten wrote:
> Tama has four GPIO-wired keys: two for camera focus and shutter /
> snapshot, and two more for volume up and down. As per the comment these
> used to not work because the necessary pin bias was missing, which is
> now set via pinctrl on pm8998_gpios.
>
> The missing bias has also been added to the existing volume down button,
> which receives a node name and label cleanup at the same time to be more
> consistent with other DTS and the newly added buttons. Its deprecated
> gpio-key,wakeup property has also been replaced with wakeup-source.
>
> [...]
Applied, thanks!
[1/1] arm64: dts: qcom: sdm845-tama: Add volume up and camera GPIO keys
commit: 4ce03bb80faed41e04b7d6f089275d262f4cfc79
Best regards,
@@ -4,6 +4,7 @@
*/
#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
#include "sdm845.dtsi"
#include "pm8005.dtsi"
@@ -17,14 +18,43 @@ / {
gpio-keys {
compatible = "gpio-keys";
- /* Neither Camera Focus, nor Camera Shutter seem to work... */
+ pinctrl-0 = <&focus_n &snapshot_n &vol_down_n &vol_up_n>;
+ pinctrl-names = "default";
- key-vol-down {
- label = "volume_down";
+ key-camera-focus {
+ label = "Camera Focus";
+ gpios = <&pm8998_gpios 2 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_CAMERA_FOCUS>;
+ debounce-interval = <15>;
+ linux,can-disable;
+ wakeup-source;
+ };
+
+ key-camera-snapshot {
+ label = "Camera Snapshot";
+ gpios = <&pm8998_gpios 7 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_CAMERA>;
+ debounce-interval = <15>;
+ linux,can-disable;
+ wakeup-source;
+ };
+
+ key-volume-down {
+ label = "Volume Down";
gpios = <&pm8998_gpios 5 GPIO_ACTIVE_LOW>;
linux,code = <KEY_VOLUMEDOWN>;
debounce-interval = <15>;
- gpio-key,wakeup;
+ linux,can-disable;
+ wakeup-source;
+ };
+
+ key-volume-up {
+ label = "Volume Up";
+ gpios = <&pm8998_gpios 6 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEUP>;
+ debounce-interval = <15>;
+ linux,can-disable;
+ wakeup-source;
};
};
@@ -358,6 +388,40 @@ &i2c14 {
/* AMS TCS3490 RGB+IR color sensor @ 72 */
};
+&pm8998_gpios {
+ focus_n: focus-n-state {
+ pins = "gpio2";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ power-source = <0>;
+ bias-pull-up;
+ input-enable;
+ };
+
+ vol_down_n: vol-down-n-state {
+ pins = "gpio5";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ power-source = <0>;
+ bias-pull-up;
+ input-enable;
+ };
+
+ vol_up_n: vol-up-n-state {
+ pins = "gpio6";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ power-source = <0>;
+ bias-pull-up;
+ input-enable;
+ };
+
+ snapshot_n: snapshot-n-state {
+ pins = "gpio7";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ power-source = <0>;
+ bias-pull-up;
+ input-enable;
+ };
+};
+
&qupv3_id_0 {
status = "okay";
};