[v6,7/7] arm64: dts: mediatek: Initial mt8365-evk support

Message ID 20221230203541.146807-8-bero@baylibre.com
State New
Headers
Series Add minimal MT8365 and MT8365-EVK support |

Commit Message

Bernhard Rosenkränzer Dec. 30, 2022, 8:35 p.m. UTC
  From: Fabien Parent <fparent@baylibre.com>

This adds minimal support for the Mediatek 8365 SOC and the EVK reference
board, allowing the board to boot to initramfs with serial port I/O.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
[bero@baylibre.com: Removed parts depending on drivers that aren't upstream yet, cleanups, add CPU cache layout, add systimer]
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
---
 arch/arm64/boot/dts/mediatek/Makefile       |   1 +
 arch/arm64/boot/dts/mediatek/mt8365-evk.dts | 169 +++++++++
 arch/arm64/boot/dts/mediatek/mt8365.dtsi    | 374 ++++++++++++++++++++
 3 files changed, 544 insertions(+)
 create mode 100644 arch/arm64/boot/dts/mediatek/mt8365-evk.dts
 create mode 100644 arch/arm64/boot/dts/mediatek/mt8365.dtsi
  

Comments

Marc Zyngier Dec. 30, 2022, 10:39 p.m. UTC | #1
On Fri, 30 Dec 2022 20:35:41 +0000,
Bernhard Rosenkränzer <bero@baylibre.com> wrote:
> 
> From: Fabien Parent <fparent@baylibre.com>
> 
> This adds minimal support for the Mediatek 8365 SOC and the EVK reference
> board, allowing the board to boot to initramfs with serial port I/O.
> 
> Signed-off-by: Fabien Parent <fparent@baylibre.com>
> [bero@baylibre.com: Removed parts depending on drivers that aren't upstream yet, cleanups, add CPU cache layout, add systimer]
> Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
> Tested-by: Kevin Hilman <khilman@baylibre.com>

[...]

> +	soc {
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		compatible = "simple-bus";
> +		ranges;
> +
> +		gic: interrupt-controller@c000000 {
> +			compatible = "arm,gic-v3";
> +			#interrupt-cells = <4>;

Why 4 cells? All the SPIs routed via sysirq are perfectly happy with 3
cells, and all the PPIs have 0 for the 4th cell (none of them use any
form of partitioning that'd require 4 cells). So where is this coming
from?

> +			interrupt-parent = <&gic>;
> +			interrupt-controller;
> +			reg = <0 0x0c000000 0 0x80000>, <0 0x0c080000 0 0x80000>;
> +

The first region is obviously wrong (512kB for the distributor?
that's... most generous, but the architecture states that it is 64kB,
and that's wasteful enough).

This is also missing the GICC/GICH/GICV regions that Cortex-A53
implements, and that must be provided as per the binding.

> +			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH 0>;
> +		};

Thanks,

	M.
  
Bernhard Rosenkränzer Jan. 1, 2023, 9:57 p.m. UTC | #2
On Fri, Dec 30, 2022 at 11:41 PM Marc Zyngier <maz@kernel.org> wrote:
> > +             gic: interrupt-controller@c000000 {
> > +                     compatible = "arm,gic-v3";
> > +                     #interrupt-cells = <4>;
>
> Why 4 cells? All the SPIs routed via sysirq are perfectly happy with 3
> cells, and all the PPIs have 0 for the 4th cell (none of them use any
> form of partitioning that'd require 4 cells). So where is this coming
> from?

It's coming from the SoC vendor kernel (and went unnoticed because it
happens to work).
Will send an updated version that does the right thing instead. I've
been running it most of the day, so far looking good.

> > +                     interrupt-parent = <&gic>;
> > +                     interrupt-controller;
> > +                     reg = <0 0x0c000000 0 0x80000>, <0 0x0c080000 0 0x80000>;
> > +
>
> The first region is obviously wrong (512kB for the distributor?
> that's... most generous, but the architecture states that it is 64kB,
> and that's wasteful enough).
>
> This is also missing the GICC/GICH/GICV regions that Cortex-A53
> implements, and that must be provided as per the binding.

This was also taken from the vendor kernel; unfortunately neiter the
datasheet for the SoC not the vendor kernel specifies the addresses
for GICC/GICH/GICV.
I've "guessed" based on what's in similar SoCs (MT8183, MT7986a) in
v7; this seems to work (boots, kvm initializes hyp mode properly).

ttyl
bero
  
Marc Zyngier Jan. 1, 2023, 10:44 p.m. UTC | #3
On Sun, 01 Jan 2023 21:57:58 +0000,
Bernhard Rosenkränzer <bero@baylibre.com> wrote:
> 
> On Fri, Dec 30, 2022 at 11:41 PM Marc Zyngier <maz@kernel.org> wrote:
> > > +             gic: interrupt-controller@c000000 {
> > > +                     compatible = "arm,gic-v3";
> > > +                     #interrupt-cells = <4>;
> >
> > Why 4 cells? All the SPIs routed via sysirq are perfectly happy with 3
> > cells, and all the PPIs have 0 for the 4th cell (none of them use any
> > form of partitioning that'd require 4 cells). So where is this coming
> > from?
> 
> It's coming from the SoC vendor kernel (and went unnoticed because
> it happens to work).  Will send an updated version that does the
> right thing instead. I've been running it most of the day, so far
> looking good.
> 
> > > +                     interrupt-parent = <&gic>;
> > > +                     interrupt-controller;
> > > +                     reg = <0 0x0c000000 0 0x80000>, <0 0x0c080000 0 0x80000>;
> > > +
> >
> > The first region is obviously wrong (512kB for the distributor?
> > that's... most generous, but the architecture states that it is 64kB,
> > and that's wasteful enough).
> >
> > This is also missing the GICC/GICH/GICV regions that Cortex-A53
> > implements, and that must be provided as per the binding.
> 
> This was also taken from the vendor kernel; unfortunately neiter the
> datasheet for the SoC not the vendor kernel specifies the addresses
> for GICC/GICH/GICV.
> I've "guessed" based on what's in similar SoCs (MT8183, MT7986a) in
> v7; this seems to work (boots, kvm initializes hyp mode properly).

Please don't "guess", because this adds zero value, and we might as
well run with the vendor crap instead.

Read CBAR_EL1, and use this value to construct the memory map, as per
the A53 TRM. Just booting with KVM enabled means nothing, as this is
solely used at VM run time. You need run a full VM with GIC-2
emulation.

	M.
  
Chunfeng Yun (云春峰) Jan. 3, 2023, 5:51 a.m. UTC | #4
On Fri, 2022-12-30 at 21:35 +0100, Bernhard Rosenkränzer wrote:
> From: Fabien Parent <fparent@baylibre.com>
> 
> This adds minimal support for the Mediatek 8365 SOC and the EVK
> reference
> board, allowing the board to boot to initramfs with serial port I/O.
> 
> Signed-off-by: Fabien Parent <fparent@baylibre.com>
> [bero@baylibre.com: Removed parts depending on drivers that aren't
> upstream yet, cleanups, add CPU cache layout, add systimer]
> Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
> Tested-by: Kevin Hilman <khilman@baylibre.com>
> ---
>  arch/arm64/boot/dts/mediatek/Makefile       |   1 +
>  arch/arm64/boot/dts/mediatek/mt8365-evk.dts | 169 +++++++++
>  arch/arm64/boot/dts/mediatek/mt8365.dtsi    | 374
> ++++++++++++++++++++
>  3 files changed, 544 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/mediatek/mt8365-evk.dts
>  create mode 100644 arch/arm64/boot/dts/mediatek/mt8365.dtsi
> 
> diff --git a/arch/arm64/boot/dts/mediatek/Makefile
> b/arch/arm64/boot/dts/mediatek/Makefile
> index 813e735c5b96d..d78523c5a7dd6 100644
> --- a/arch/arm64/boot/dts/mediatek/Makefile
> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> @@ -47,4 +47,5 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-
> tomato-r2.dtb
>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r3.dtb
>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-demo.dtb
>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8365-evk.dtb
>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb
> diff --git a/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
> b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
> new file mode 100644
> index 0000000000000..275ea3a0e7085
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
> @@ -0,0 +1,169 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2021-2022 BayLibre, SAS.
> + * Authors:
> + * Fabien Parent <fparent@baylibre.com>
> + * Bernhard Rosenkränzer <bero@baylibre.com>
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/pinctrl/mt8365-pinfunc.h>
> +#include "mt8365.dtsi"
> +
> +/ {
> +	model = "MediaTek MT8365 Open Platform EVK";
> +	compatible = "mediatek,mt8365-evk", "mediatek,mt8365";
> +
> +	aliases {
> +		serial0 = &uart0;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:921600n8";
> +	};
> +
> +	firmware {
> +		optee {
> +			compatible = "linaro,optee-tz";
> +			method = "smc";
> +		};
> +	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +		input-name = "gpio-keys";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&gpio_keys>;
> +
> +		key-volume-up {
> +			gpios = <&pio 24 GPIO_ACTIVE_LOW>;
> +			label = "volume_up";
> +			linux,code = <KEY_VOLUMEUP>;
> +			wakeup-source;
> +			debounce-interval = <15>;
> +		};
> +	};
> +
> +	memory@40000000 {
> +		device_type = "memory";
> +		reg = <0 0x40000000 0 0xc0000000>;
> +	};
> +
> +	usb_otg_vbus: regulator-0 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "otg_vbus";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		gpio = <&pio 16 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +
> +	reserved-memory {
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		ranges;
> +
> +		/* 128 KiB reserved for ARM Trusted Firmware (BL31) */
> +		bl31_secmon_reserved: secmon@43000000 {
> +			no-map;
> +			reg = <0 0x43000000 0 0x20000>;
> +		};
> +
> +		/* 12 MiB reserved for OP-TEE (BL32)
> +		 * +-----------------------+ 0x43e0_0000
> +		 * |      SHMEM 2MiB       |
> +		 * +-----------------------+ 0x43c0_0000
> +		 * |        | TA_RAM  8MiB |
> +		 * + TZDRAM +--------------+ 0x4340_0000
> +		 * |        | TEE_RAM 2MiB |
> +		 * +-----------------------+ 0x4320_0000
> +		 */
> +		optee_reserved: optee@43200000 {
> +			no-map;
> +			reg = <0 0x43200000 0 0x00c00000>;
> +		};
> +	};
> +};
> +
> +&pio {
> +	gpio_keys: gpio-keys-pins {
> +		pins {
> +			pinmux = <MT8365_PIN_24_KPCOL0__FUNC_KPCOL0>;
> +			bias-pull-up;
> +			input-enable;
> +		};
> +	};
> +
> +	uart0_pins: uart0-pins {
> +		pins {
> +			pinmux = <MT8365_PIN_35_URXD0__FUNC_URXD0>,
> +				 <MT8365_PIN_36_UTXD0__FUNC_UTXD0>;
> +		};
> +	};
> +
> +	uart1_pins: uart1-pins {
> +		pins {
> +			pinmux = <MT8365_PIN_37_URXD1__FUNC_URXD1>,
> +				 <MT8365_PIN_38_UTXD1__FUNC_UTXD1>;
> +		};
> +	};
> +
> +	uart2_pins: uart2-pins {
> +		pins {
> +			pinmux = <MT8365_PIN_39_URXD2__FUNC_URXD2>,
> +				 <MT8365_PIN_40_UTXD2__FUNC_UTXD2>;
> +		};
> +	};
> +
> +	usb_pins: usb-pins {
> +		pins-id {
> +			pinmux = <MT8365_PIN_17_GPIO17__FUNC_GPIO17>;
> +			input-enable;
> +			bias-pull-up;
> +		};
> +
> +		pins-usb0-vbus {
> +			pinmux =
> <MT8365_PIN_16_GPIO16__FUNC_USB_DRVVBUS>;
> +			output-high;
> +		};
> +
> +		pin-usb1-vbus {
> +			pinmux = <MT8365_PIN_18_GPIO18__FUNC_GPIO18>;
> +			output-high;
> +		};
> +	};
> +
> +	pwm_pins: pwm-pins {
> +		pins {
> +			pinmux = <MT8365_PIN_19_DISP_PWM__FUNC_PWM_A>,
> +				 <MT8365_PIN_116_I2S_BCK__FUNC_PWM_C>;
> +		};
> +	};
> +};
> +
> +&pwm {
> +	pinctrl-0 = <&pwm_pins>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +};
> +
> +&uart0 {
> +	pinctrl-0 = <&uart0_pins>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +};
> +
> +&uart1 {
> +	pinctrl-0 = <&uart1_pins>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +};
> +
> +&uart2 {
> +	pinctrl-0 = <&uart2_pins>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/mediatek/mt8365.dtsi
> b/arch/arm64/boot/dts/mediatek/mt8365.dtsi
> new file mode 100644
> index 0000000000000..60a211ba91dbd
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8365.dtsi
> @@ -0,0 +1,374 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * (C) 2018 MediaTek Inc.
> + * Copyright (C) 2022 BayLibre SAS
> + * Fabien Parent <fparent@baylibre.com>
> + * Bernhard Rosenkränzer <bero@baylibre.com>
> + */
> +#include <dt-bindings/clock/mediatek,mt8365-clk.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/phy/phy.h>
> +#include <dt-bindings/thermal/thermal.h>
> +
> +/ {
> +	compatible = "mediatek,mt8365";
> +	interrupt-parent = <&sysirq>;
> +	#address-cells = <2>;
> +	#size-cells = <2>;
> +
> +	cpus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		cpu-map {
> +			cluster0 {
> +				core0 {
> +					cpu = <&cpu0>;
> +				};
> +				core1 {
> +					cpu = <&cpu1>;
> +				};
> +				core2 {
> +					cpu = <&cpu2>;
> +				};
> +				core3 {
> +					cpu = <&cpu3>;
> +				};
> +			};
> +		};
> +
> +		cpu0: cpu@0 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a53";
> +			reg = <0x0>;
> +			#cooling-cells = <2>;
> +			enable-method = "psci";
> +			i-cache-size = <0x8000>;
> +			i-cache-line-size = <64>;
> +			i-cache-sets = <256>;
> +			d-cache-size = <0x8000>;
> +			d-cache-line-size = <64>;
> +			d-cache-sets = <256>;
> +			next-level-cache = <&l2>;
> +		};
> +
> +		cpu1: cpu@1 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a53";
> +			reg = <0x1>;
> +			#cooling-cells = <2>;
> +			enable-method = "psci";
> +			i-cache-size = <0x8000>;
> +			i-cache-line-size = <64>;
> +			i-cache-sets = <256>;
> +			d-cache-size = <0x8000>;
> +			d-cache-line-size = <64>;
> +			d-cache-sets = <256>;
> +			next-level-cache = <&l2>;
> +		};
> +
> +		cpu2: cpu@2 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a53";
> +			reg = <0x2>;
> +			#cooling-cells = <2>;
> +			enable-method = "psci";
> +			i-cache-size = <0x8000>;
> +			i-cache-line-size = <64>;
> +			i-cache-sets = <256>;
> +			d-cache-size = <0x8000>;
> +			d-cache-line-size = <64>;
> +			d-cache-sets = <256>;
> +			next-level-cache = <&l2>;
> +		};
> +
> +		cpu3: cpu@3 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a53";
> +			reg = <0x3>;
> +			#cooling-cells = <2>;
> +			enable-method = "psci";
> +			i-cache-size = <0x8000>;
> +			i-cache-line-size = <64>;
> +			i-cache-sets = <256>;
> +			d-cache-size = <0x8000>;
> +			d-cache-line-size = <64>;
> +			d-cache-sets = <256>;
> +			next-level-cache = <&l2>;
> +		};
> +
> +		l2: l2-cache {
> +			compatible = "cache";
> +			cache-level = <2>;
> +			cache-size = <0x80000>;
> +			cache-line-size = <64>;
> +			cache-sets = <512>;
> +			cache-unified;
> +		};
> +	};
> +
> +	clk26m: oscillator {
> +		compatible = "fixed-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <26000000>;
> +		clock-output-names = "clk26m";
> +	};
> +
> +	psci {
> +		compatible = "arm,psci-1.0";
> +		method = "smc";
> +	};
> +
> +	soc {
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		compatible = "simple-bus";
> +		ranges;
> +
> +		gic: interrupt-controller@c000000 {
> +			compatible = "arm,gic-v3";
> +			#interrupt-cells = <4>;
> +			interrupt-parent = <&gic>;
> +			interrupt-controller;
> +			reg = <0 0x0c000000 0 0x80000>, <0 0x0c080000 0
> 0x80000>;
> +
> +			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH 0>;
> +		};
> +
> +		topckgen: syscon@10000000 {
> +			compatible = "mediatek,mt8365-topckgen",
> "syscon";
> +			reg = <0 0x10000000 0 0x1000>;
> +			#clock-cells = <1>;
> +		};
> +
> +		infracfg: syscon@10001000 {
> +			compatible = "mediatek,mt8365-infracfg",
> "syscon";
> +			reg = <0 0x10001000 0 0x1000>;
> +			#clock-cells = <1>;
> +		};
> +
> +		pericfg: syscon@10003000 {
> +			compatible = "mediatek,mt8365-pericfg",
> "syscon";
> +			reg = <0 0x10003000 0 0x1000>;
> +			#clock-cells = <1>;
> +		};
> +
> +		syscfg_pctl: syscfg-pctl@10005000 {
> +			compatible = "mediatek,mt8365-syscfg",
> "syscon";
> +			reg = <0 0x10005000 0 0x1000>;
> +		};
> +
> +		pio: pinctrl@1000b000 {
> +			compatible = "mediatek,mt8365-pinctrl";
> +			reg = <0 0x1000b000 0 0x1000>;
> +			mediatek,pctl-regmap = <&syscfg_pctl>;
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +			interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
> +		};
> +
> +		apmixedsys: syscon@1000c000 {
> +			compatible = "mediatek,mt8365-apmixedsys",
> "syscon";
> +			reg = <0 0x1000c000 0 0x1000>;
> +			#clock-cells = <1>;
> +		};
> +
> +		keypad: keypad@10010000 {
> +			compatible = "mediatek,mt6779-keypad";
> +			reg = <0 0x10010000 0 0x1000>;
> +			wakeup-source;
> +			interrupts = <GIC_SPI 124
> IRQ_TYPE_EDGE_FALLING>;
> +			clocks = <&clk26m>;
> +			clock-names = "kpd";
> +			status = "disabled";
> +		};
> +
> +		mcucfg: syscon@10200000 {
> +			compatible = "mediatek,mt8365-mcucfg",
> "syscon";
> +			reg = <0 0x10200000 0 0x2000>;
> +			#clock-cells = <1>;
> +		};
> +
> +		sysirq: interrupt-controller@10200a80 {
> +			compatible = "mediatek,mt8365-sysirq",
> "mediatek,mt6577-sysirq";
> +			interrupt-controller;
> +			#interrupt-cells = <3>;
> +			interrupt-parent = <&gic>;
> +			reg = <0 0x10200a80 0 0x20>;
> +		};
> +
> +		infracfg_nao: infracfg@1020e000 {
> +			compatible = "mediatek,mt8365-infracfg",
> "syscon";
> +			reg = <0 0x1020e000 0 0x1000>;
> +		};
> +
> +		rng: rng@1020f000 {
> +			compatible = "mediatek,mt8365-rng",
> "mediatek,mt7623-rng";
> +			reg = <0 0x1020f000 0 0x100>;
> +			clocks = <&infracfg CLK_IFR_TRNG>;
> +			clock-names = "rng";
> +		};
> +
> +		apdma: dma-controller@11000280 {
> +			compatible = "mediatek,mt8365-uart-dma",
> "mediatek,mt6577-uart-dma";
> +			reg = <0 0x11000280 0 0x80>,
> +			      <0 0x11000300 0 0x80>,
> +			      <0 0x11000380 0 0x80>,
> +			      <0 0x11000400 0 0x80>,
> +			      <0 0x11000580 0 0x80>,
> +			      <0 0x11000600 0 0x80>;
> +			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_LOW>,
> +				     <GIC_SPI 46 IRQ_TYPE_LEVEL_LOW>,
> +				     <GIC_SPI 47 IRQ_TYPE_LEVEL_LOW>,
> +				     <GIC_SPI 48 IRQ_TYPE_LEVEL_LOW>,
> +				     <GIC_SPI 51 IRQ_TYPE_LEVEL_LOW>,
> +				     <GIC_SPI 52 IRQ_TYPE_LEVEL_LOW>;
> +			dma-requests = <6>;
> +			clocks = <&infracfg CLK_IFR_AP_DMA>;
> +			clock-names = "apdma";
> +			#dma-cells = <1>;
> +		};
> +
> +		uart0: serial@11002000 {
> +			compatible = "mediatek,mt8365-uart",
> "mediatek,mt6577-uart";
> +			reg = <0 0x11002000 0 0x1000>;
> +			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_LOW>;
> +			clocks = <&clk26m>, <&infracfg CLK_IFR_UART0>;
> +			clock-names = "baud", "bus";
> +			dmas = <&apdma 0>, <&apdma 1>;
> +			dma-names = "tx", "rx";
> +			status = "disabled";
> +		};
> +
> +		uart1: serial@11003000 {
> +			compatible = "mediatek,mt8365-uart",
> "mediatek,mt6577-uart";
> +			reg = <0 0x11003000 0 0x1000>;
> +			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_LOW>;
> +			clocks = <&clk26m>, <&infracfg CLK_IFR_UART1>;
> +			clock-names = "baud", "bus";
> +			dmas = <&apdma 2>, <&apdma 3>;
> +			dma-names = "tx", "rx";
> +			status = "disabled";
> +		};
> +
> +		uart2: serial@11004000 {
> +			compatible = "mediatek,mt8365-uart",
> "mediatek,mt6577-uart";
> +			reg = <0 0x11004000 0 0x1000>;
> +			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_LOW>;
> +			clocks = <&clk26m>, <&infracfg CLK_IFR_UART2>;
> +			clock-names = "baud", "bus";
> +			dmas = <&apdma 4>, <&apdma 5>;
> +			dma-names = "tx", "rx";
> +			status = "disabled";
> +		};
> +
> +		pwm: pwm@11006000 {
> +			compatible = "mediatek,mt8365-pwm";
> +			reg = <0 0x11006000 0 0x1000>;
> +			#pwm-cells = <2>;
> +			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_LOW>;
> +			clocks = <&infracfg CLK_IFR_PWM_HCLK>,
> +				 <&infracfg CLK_IFR_PWM>,
> +				 <&infracfg CLK_IFR_PWM1>,
> +				 <&infracfg CLK_IFR_PWM2>,
> +				 <&infracfg CLK_IFR_PWM3>;
> +			clock-names = "top", "main", "pwm1", "pwm2",
> "pwm3";
> +		};
> +
> +		spi: spi@1100a000 {
> +			compatible = "mediatek,mt8365-spi",
> "mediatek,mt7622-spi";
> +			reg = <0 0x1100a000 0 0x100>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_LOW>;
> +			clocks = <&topckgen CLK_TOP_UNIVPLL2_D4>,
> +				 <&topckgen CLK_TOP_SPI_SEL>,
> +				 <&infracfg CLK_IFR_SPI0>;
> +			clock-names = "parent-clk", "sel-clk", "spi-
> clk";
> +			status = "disabled";
> +		};
> +
> +		ssusb: usb@11201000 {
> +			compatible = "mediatek,mt8365-mtu3",
> "mediatek,mtu3";
> +			reg = <0 0x11201000 0 0x2e00>, <0 0x11203e00 0
> 0x0100>;
> +			reg-names = "mac", "ippc";
> +			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_LOW>;
> +			phys = <&u2port0 PHY_TYPE_USB2>,
> +			       <&u2port1 PHY_TYPE_USB2>;
> +			clocks = <&topckgen CLK_TOP_SSUSB_TOP_CK_EN>,
> +				 <&infracfg CLK_IFR_SSUSB_REF>,
> +				 <&infracfg CLK_IFR_SSUSB_SYS>,
> +				 <&infracfg CLK_IFR_ICUSB>;
> +			clock-names = "sys_ck", "ref_ck", "mcu_ck",
> "dma_ck";
> +			#address-cells = <2>;
> +			#size-cells = <2>;
> +			ranges;
> +			status = "disabled";
> +
> +			usb_host: usb@11200000 {
> +				compatible = "mediatek,mt8365-xhci",
> "mediatek,mtk-xhci";
> +				reg = <0 0x11200000 0 0x1000>;
> +				reg-names = "mac";
> +				interrupts = <GIC_SPI 67
> IRQ_TYPE_LEVEL_LOW>;
> +				clocks = <&topckgen
> CLK_TOP_SSUSB_TOP_CK_EN>,
> +					 <&infracfg CLK_IFR_SSUSB_REF>,
> +					 <&infracfg CLK_IFR_SSUSB_SYS>,
> +					 <&infracfg CLK_IFR_ICUSB>,
> +					 <&infracfg
> CLK_IFR_SSUSB_XHCI>;
> +				clock-names = "sys_ck", "ref_ck",
> "mcu_ck",
> +					      "dma_ck", "xhci_ck";
> +				status = "disabled";
> +			};
> +		};
> +
> +		u3phy: phy@11cc0000 {
> +			compatible = "mediatek,mt8365-tphy",
> "mediatek,generic-tphy-v2";
> +			#address-cells = <2>;
> +			#size-cells = <2>;
> +			#phy-cells = <1>;
> +			ranges;
Prefer to use ranges with triplet value, refers to mt2712's

Thanks a lot

> +
> +			u2port0: usb-phy@11cc0000 {
> +				reg = <0 0x11cc0000 0 0x400>;
> +				clocks = <&topckgen
> CLK_TOP_SSUSB_PHY_CK_EN>,
> +					 <&topckgen
> CLK_TOP_USB20_48M_EN>;
> +				clock-names = "ref", "da_ref";
> +				#phy-cells = <1>;
> +			};
> +
> +			u2port1: usb-phy@11cc1000 {
> +				reg = <0 0x11cc1000 0 0x400>;
> +				clocks = <&topckgen
> CLK_TOP_SSUSB_PHY_CK_EN>,
> +					 <&topckgen
> CLK_TOP_USB20_48M_EN>;
> +				clock-names = "ref", "da_ref";
> +				#phy-cells = <1>;
> +			};
> +		};
> +	};
> +
> +	timer {
> +		compatible = "arm,armv8-timer";
> +		interrupt-parent = <&gic>;
> +		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW 0>,
> +			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW 0>,
> +			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW 0>,
> +			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW 0>;
> +	};
> +
> +	system_clk: dummy13m {
> +		compatible = "fixed-clock";
> +		clock-frequency = <13000000>;
> +		#clock-cells = <0>;
> +	};
> +
> +	systimer: timer@10017000 {
> +		compatible = "mediatek,mt6795-systimer";
> +		reg = <0 0x10017000 0 0x10>;
> +		interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_LOW>;
> +		clocks = <&system_clk>;
> +		clock-names = "clk13m";
> +	};
> +};
  

Patch

diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 813e735c5b96d..d78523c5a7dd6 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -47,4 +47,5 @@  dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r2.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r3.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-demo.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8365-evk.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt8365-evk.dts b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
new file mode 100644
index 0000000000000..275ea3a0e7085
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
@@ -0,0 +1,169 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2021-2022 BayLibre, SAS.
+ * Authors:
+ * Fabien Parent <fparent@baylibre.com>
+ * Bernhard Rosenkränzer <bero@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/mt8365-pinfunc.h>
+#include "mt8365.dtsi"
+
+/ {
+	model = "MediaTek MT8365 Open Platform EVK";
+	compatible = "mediatek,mt8365-evk", "mediatek,mt8365";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:921600n8";
+	};
+
+	firmware {
+		optee {
+			compatible = "linaro,optee-tz";
+			method = "smc";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		input-name = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys>;
+
+		key-volume-up {
+			gpios = <&pio 24 GPIO_ACTIVE_LOW>;
+			label = "volume_up";
+			linux,code = <KEY_VOLUMEUP>;
+			wakeup-source;
+			debounce-interval = <15>;
+		};
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0 0x40000000 0 0xc0000000>;
+	};
+
+	usb_otg_vbus: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&pio 16 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/* 128 KiB reserved for ARM Trusted Firmware (BL31) */
+		bl31_secmon_reserved: secmon@43000000 {
+			no-map;
+			reg = <0 0x43000000 0 0x20000>;
+		};
+
+		/* 12 MiB reserved for OP-TEE (BL32)
+		 * +-----------------------+ 0x43e0_0000
+		 * |      SHMEM 2MiB       |
+		 * +-----------------------+ 0x43c0_0000
+		 * |        | TA_RAM  8MiB |
+		 * + TZDRAM +--------------+ 0x4340_0000
+		 * |        | TEE_RAM 2MiB |
+		 * +-----------------------+ 0x4320_0000
+		 */
+		optee_reserved: optee@43200000 {
+			no-map;
+			reg = <0 0x43200000 0 0x00c00000>;
+		};
+	};
+};
+
+&pio {
+	gpio_keys: gpio-keys-pins {
+		pins {
+			pinmux = <MT8365_PIN_24_KPCOL0__FUNC_KPCOL0>;
+			bias-pull-up;
+			input-enable;
+		};
+	};
+
+	uart0_pins: uart0-pins {
+		pins {
+			pinmux = <MT8365_PIN_35_URXD0__FUNC_URXD0>,
+				 <MT8365_PIN_36_UTXD0__FUNC_UTXD0>;
+		};
+	};
+
+	uart1_pins: uart1-pins {
+		pins {
+			pinmux = <MT8365_PIN_37_URXD1__FUNC_URXD1>,
+				 <MT8365_PIN_38_UTXD1__FUNC_UTXD1>;
+		};
+	};
+
+	uart2_pins: uart2-pins {
+		pins {
+			pinmux = <MT8365_PIN_39_URXD2__FUNC_URXD2>,
+				 <MT8365_PIN_40_UTXD2__FUNC_UTXD2>;
+		};
+	};
+
+	usb_pins: usb-pins {
+		pins-id {
+			pinmux = <MT8365_PIN_17_GPIO17__FUNC_GPIO17>;
+			input-enable;
+			bias-pull-up;
+		};
+
+		pins-usb0-vbus {
+			pinmux = <MT8365_PIN_16_GPIO16__FUNC_USB_DRVVBUS>;
+			output-high;
+		};
+
+		pin-usb1-vbus {
+			pinmux = <MT8365_PIN_18_GPIO18__FUNC_GPIO18>;
+			output-high;
+		};
+	};
+
+	pwm_pins: pwm-pins {
+		pins {
+			pinmux = <MT8365_PIN_19_DISP_PWM__FUNC_PWM_A>,
+				 <MT8365_PIN_116_I2S_BCK__FUNC_PWM_C>;
+		};
+	};
+};
+
+&pwm {
+	pinctrl-0 = <&pwm_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-0 = <&uart0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-0 = <&uart1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-0 = <&uart2_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8365.dtsi b/arch/arm64/boot/dts/mediatek/mt8365.dtsi
new file mode 100644
index 0000000000000..60a211ba91dbd
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8365.dtsi
@@ -0,0 +1,374 @@ 
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * (C) 2018 MediaTek Inc.
+ * Copyright (C) 2022 BayLibre SAS
+ * Fabien Parent <fparent@baylibre.com>
+ * Bernhard Rosenkränzer <bero@baylibre.com>
+ */
+#include <dt-bindings/clock/mediatek,mt8365-clk.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+	compatible = "mediatek,mt8365";
+	interrupt-parent = <&sysirq>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+				core1 {
+					cpu = <&cpu1>;
+				};
+				core2 {
+					cpu = <&cpu2>;
+				};
+				core3 {
+					cpu = <&cpu3>;
+				};
+			};
+		};
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x0>;
+			#cooling-cells = <2>;
+			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x1>;
+			#cooling-cells = <2>;
+			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2>;
+		};
+
+		cpu2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x2>;
+			#cooling-cells = <2>;
+			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2>;
+		};
+
+		cpu3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x3>;
+			#cooling-cells = <2>;
+			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2>;
+		};
+
+		l2: l2-cache {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-size = <0x80000>;
+			cache-line-size = <64>;
+			cache-sets = <512>;
+			cache-unified;
+		};
+	};
+
+	clk26m: oscillator {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+		clock-output-names = "clk26m";
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	soc {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		compatible = "simple-bus";
+		ranges;
+
+		gic: interrupt-controller@c000000 {
+			compatible = "arm,gic-v3";
+			#interrupt-cells = <4>;
+			interrupt-parent = <&gic>;
+			interrupt-controller;
+			reg = <0 0x0c000000 0 0x80000>, <0 0x0c080000 0 0x80000>;
+
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH 0>;
+		};
+
+		topckgen: syscon@10000000 {
+			compatible = "mediatek,mt8365-topckgen", "syscon";
+			reg = <0 0x10000000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		infracfg: syscon@10001000 {
+			compatible = "mediatek,mt8365-infracfg", "syscon";
+			reg = <0 0x10001000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		pericfg: syscon@10003000 {
+			compatible = "mediatek,mt8365-pericfg", "syscon";
+			reg = <0 0x10003000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		syscfg_pctl: syscfg-pctl@10005000 {
+			compatible = "mediatek,mt8365-syscfg", "syscon";
+			reg = <0 0x10005000 0 0x1000>;
+		};
+
+		pio: pinctrl@1000b000 {
+			compatible = "mediatek,mt8365-pinctrl";
+			reg = <0 0x1000b000 0 0x1000>;
+			mediatek,pctl-regmap = <&syscfg_pctl>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		apmixedsys: syscon@1000c000 {
+			compatible = "mediatek,mt8365-apmixedsys", "syscon";
+			reg = <0 0x1000c000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		keypad: keypad@10010000 {
+			compatible = "mediatek,mt6779-keypad";
+			reg = <0 0x10010000 0 0x1000>;
+			wakeup-source;
+			interrupts = <GIC_SPI 124 IRQ_TYPE_EDGE_FALLING>;
+			clocks = <&clk26m>;
+			clock-names = "kpd";
+			status = "disabled";
+		};
+
+		mcucfg: syscon@10200000 {
+			compatible = "mediatek,mt8365-mcucfg", "syscon";
+			reg = <0 0x10200000 0 0x2000>;
+			#clock-cells = <1>;
+		};
+
+		sysirq: interrupt-controller@10200a80 {
+			compatible = "mediatek,mt8365-sysirq", "mediatek,mt6577-sysirq";
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			interrupt-parent = <&gic>;
+			reg = <0 0x10200a80 0 0x20>;
+		};
+
+		infracfg_nao: infracfg@1020e000 {
+			compatible = "mediatek,mt8365-infracfg", "syscon";
+			reg = <0 0x1020e000 0 0x1000>;
+		};
+
+		rng: rng@1020f000 {
+			compatible = "mediatek,mt8365-rng", "mediatek,mt7623-rng";
+			reg = <0 0x1020f000 0 0x100>;
+			clocks = <&infracfg CLK_IFR_TRNG>;
+			clock-names = "rng";
+		};
+
+		apdma: dma-controller@11000280 {
+			compatible = "mediatek,mt8365-uart-dma", "mediatek,mt6577-uart-dma";
+			reg = <0 0x11000280 0 0x80>,
+			      <0 0x11000300 0 0x80>,
+			      <0 0x11000380 0 0x80>,
+			      <0 0x11000400 0 0x80>,
+			      <0 0x11000580 0 0x80>,
+			      <0 0x11000600 0 0x80>;
+			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_LOW>,
+				     <GIC_SPI 46 IRQ_TYPE_LEVEL_LOW>,
+				     <GIC_SPI 47 IRQ_TYPE_LEVEL_LOW>,
+				     <GIC_SPI 48 IRQ_TYPE_LEVEL_LOW>,
+				     <GIC_SPI 51 IRQ_TYPE_LEVEL_LOW>,
+				     <GIC_SPI 52 IRQ_TYPE_LEVEL_LOW>;
+			dma-requests = <6>;
+			clocks = <&infracfg CLK_IFR_AP_DMA>;
+			clock-names = "apdma";
+			#dma-cells = <1>;
+		};
+
+		uart0: serial@11002000 {
+			compatible = "mediatek,mt8365-uart", "mediatek,mt6577-uart";
+			reg = <0 0x11002000 0 0x1000>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&clk26m>, <&infracfg CLK_IFR_UART0>;
+			clock-names = "baud", "bus";
+			dmas = <&apdma 0>, <&apdma 1>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		uart1: serial@11003000 {
+			compatible = "mediatek,mt8365-uart", "mediatek,mt6577-uart";
+			reg = <0 0x11003000 0 0x1000>;
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&clk26m>, <&infracfg CLK_IFR_UART1>;
+			clock-names = "baud", "bus";
+			dmas = <&apdma 2>, <&apdma 3>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		uart2: serial@11004000 {
+			compatible = "mediatek,mt8365-uart", "mediatek,mt6577-uart";
+			reg = <0 0x11004000 0 0x1000>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&clk26m>, <&infracfg CLK_IFR_UART2>;
+			clock-names = "baud", "bus";
+			dmas = <&apdma 4>, <&apdma 5>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		pwm: pwm@11006000 {
+			compatible = "mediatek,mt8365-pwm";
+			reg = <0 0x11006000 0 0x1000>;
+			#pwm-cells = <2>;
+			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&infracfg CLK_IFR_PWM_HCLK>,
+				 <&infracfg CLK_IFR_PWM>,
+				 <&infracfg CLK_IFR_PWM1>,
+				 <&infracfg CLK_IFR_PWM2>,
+				 <&infracfg CLK_IFR_PWM3>;
+			clock-names = "top", "main", "pwm1", "pwm2", "pwm3";
+		};
+
+		spi: spi@1100a000 {
+			compatible = "mediatek,mt8365-spi", "mediatek,mt7622-spi";
+			reg = <0 0x1100a000 0 0x100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&topckgen CLK_TOP_UNIVPLL2_D4>,
+				 <&topckgen CLK_TOP_SPI_SEL>,
+				 <&infracfg CLK_IFR_SPI0>;
+			clock-names = "parent-clk", "sel-clk", "spi-clk";
+			status = "disabled";
+		};
+
+		ssusb: usb@11201000 {
+			compatible = "mediatek,mt8365-mtu3", "mediatek,mtu3";
+			reg = <0 0x11201000 0 0x2e00>, <0 0x11203e00 0 0x0100>;
+			reg-names = "mac", "ippc";
+			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_LOW>;
+			phys = <&u2port0 PHY_TYPE_USB2>,
+			       <&u2port1 PHY_TYPE_USB2>;
+			clocks = <&topckgen CLK_TOP_SSUSB_TOP_CK_EN>,
+				 <&infracfg CLK_IFR_SSUSB_REF>,
+				 <&infracfg CLK_IFR_SSUSB_SYS>,
+				 <&infracfg CLK_IFR_ICUSB>;
+			clock-names = "sys_ck", "ref_ck", "mcu_ck", "dma_ck";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			status = "disabled";
+
+			usb_host: usb@11200000 {
+				compatible = "mediatek,mt8365-xhci", "mediatek,mtk-xhci";
+				reg = <0 0x11200000 0 0x1000>;
+				reg-names = "mac";
+				interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_LOW>;
+				clocks = <&topckgen CLK_TOP_SSUSB_TOP_CK_EN>,
+					 <&infracfg CLK_IFR_SSUSB_REF>,
+					 <&infracfg CLK_IFR_SSUSB_SYS>,
+					 <&infracfg CLK_IFR_ICUSB>,
+					 <&infracfg CLK_IFR_SSUSB_XHCI>;
+				clock-names = "sys_ck", "ref_ck", "mcu_ck",
+					      "dma_ck", "xhci_ck";
+				status = "disabled";
+			};
+		};
+
+		u3phy: phy@11cc0000 {
+			compatible = "mediatek,mt8365-tphy", "mediatek,generic-tphy-v2";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			#phy-cells = <1>;
+			ranges;
+
+			u2port0: usb-phy@11cc0000 {
+				reg = <0 0x11cc0000 0 0x400>;
+				clocks = <&topckgen CLK_TOP_SSUSB_PHY_CK_EN>,
+					 <&topckgen CLK_TOP_USB20_48M_EN>;
+				clock-names = "ref", "da_ref";
+				#phy-cells = <1>;
+			};
+
+			u2port1: usb-phy@11cc1000 {
+				reg = <0 0x11cc1000 0 0x400>;
+				clocks = <&topckgen CLK_TOP_SSUSB_PHY_CK_EN>,
+					 <&topckgen CLK_TOP_USB20_48M_EN>;
+				clock-names = "ref", "da_ref";
+				#phy-cells = <1>;
+			};
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW 0>,
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW 0>,
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW 0>,
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW 0>;
+	};
+
+	system_clk: dummy13m {
+		compatible = "fixed-clock";
+		clock-frequency = <13000000>;
+		#clock-cells = <0>;
+	};
+
+	systimer: timer@10017000 {
+		compatible = "mediatek,mt6795-systimer";
+		reg = <0 0x10017000 0 0x10>;
+		interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&system_clk>;
+		clock-names = "clk13m";
+	};
+};